EMC 2 CABLE GLANDS These EMC cable glands combine several advantages in one product. First, you get the same clamping ranges as the standard brass glands. The protection class is IP68. In order to get a low electrical impedance between the cable gland and the braiding of the cable the cable gland does not have to be disassembled. Secondly, a perfect shielding will be achieved by just tightening the dome nut. This high tech cable gland consists of a nickel plated brass body, PA6 clamping insert, an EMC contact element and choloprene seal. The components are preassembled. To install an EMC cable gland remove approx. mm (0. 0.39) of the insulation of the cable. Insert the cable in to the cable gland and adjust it without the contact elements touching the braiding. Tighten the cap and conductivity will be established. The design of the contact elements will adapt to different cable diameters according to the clamping range of the cable glands. Since the clamping insert of the cable gland is as long as the gland itself electrical shortcuts between the body and individual wires will be avoided. Tightening the dome nut will have three different effects: The cable will be centered in the cable gland, the choloprene seal will ensure IP 68 protection, and the design of the dome cap will provide appropriate strain relief. All is done by just one turn of the dome cap. Even uninstalling the cable is easy; open the dome cap and pull the cable out of the cable gland together with the insert, which can then be removed easily. Tighten the cable gland to the housing. Insert cable until EMC spring. Remove outer sheath of shielded cable Lock and tight the cap. EMC 2 SERIES INTRO
BMEM-BMEN EMC 2 SERIES METRIC TREAD CABLE GLANDS - C up to + C -40 C up to +1 C EN 60423 D Manufactured according to the requirements of EN 262 Thread Type Ø min-max mm MX1, - 6, - 4, -,0 MX1, -,0 MX1,,0 - MX1,,0-1 1-1 - 1 -,0-32,0 MX1, - 32,0 MX1, - 3 Glands with Long Thread MX1, - 6, - MX1, -,0 MX1,,0-1 - 1 1 -,0 MX1, - 32,0 Ø min mm 2, 4, 8,, 11,0 1 2 31,0 2, 4, 8, 11,0 1 31,0 mm mm 7,0 6,,0,0,0,0 1 1 1 1 mm D mm Box/Min.OQ 1 27,0 3 4,0 7,0 6 2,0 2 37,0 3 3 42,0 47,0 4 s, 18,9 26,8 41,8 44,, 62,7 70,0 BMEM-0S BMEM-01 BMEM-01S BMEM-02 BMEM-03 BMEM-03S BMEM-04 BMEM-04S BMEM-0 BMEM-0S BMEM-06 BMEM-06S BMEM-07 1.0 1.0 0 400 3 2 160 140 90 70 1 27,0 3 4 6 21,8 22,6 27, 3 47,3 2,2, 18,9 26,8 44,, 70,0 BMEN-0S BMEN-01 BMEN-02 BMEN-03 BMEN-04 BMEN-0 BMEN-06 BMEN-07 1.0 400 300 160 90 mm mm,0 1 1,0,0 32,0 32,0,0,0 6,0,0 7,0,0 1,0 32,0,0 6,0
EMC 2 SERIES PG TREAD CABLE GLANDS BESM-BSEN - C up to + C -40 C up to +1 C DIN 40430 D Manufactured according to the requirements of EN 262 Thread Type Ø min-max mm Pg7-6, Pg9 - Pg11 -,0 Pg1 -,0 Pg16,0 - Pg21 1-1 Pg29 1 -,0 Pg36-32,0 Pg42-3 Pg48 Glands with Long Thread Pg7-6, Pg9 - Pg11 -,0 Pg1 -,0 Pg16,0 - Pg21 1-1 Pg29 1 -,0 Pg36-32,0 Pg42-3 Pg48 Ø min mm 2, 8, 11,0 1 2 31,0 2, 8, 11,0 1 2 31,0 mm mm 6, 6, 7,2,0,0,0,0,0,0,0 1 1 mm D mm Box/Min.OQ,0 21,8 22,6,3 24,1 27, 31,2 39,3 47,2 47,7 2,0, 18,9 26,8 44,, 70,0 BSEM-01 BSEM-02 BSEM-03 BSEM-04 BSEM-0 BSEM-06 BSEM-07 BSEM-08 BSEM-09 BSEM- 1.0 600 3 160 90,0 21,8 22,6,3 24,1 27, 31,2 39,3 47,2 47,7 2,0, 18,9 26,8 44,, 70,0 BSEN-01 BSEN-02 BSEN-03 BSEN-04 BSEN-0 BSEN-06 BSEN-07 BSEN-08 BSEN-09 BSEN- 1.0 0 3 160 90 mm mm,,2 18,6,4 22, 28,3 37,0 47,0 9,3,0,,2 18,6,4 22, 28,3 37,0 47,0 9,3,0
EMC 2 SERIES NPT TREAD CABLE GLANDS BNEM - C up to + C -40 C up to +1 C ANSI B1..1 D Manufactured according to the requirements of EN 262 Thread Type NPT3/8" NPT1/2" NPT3/4" NPT1" Ø min-max inch 0,196-0,393 0,236-0,4 0,11-0,708 0,708-0,984 Ø min inch 0,7 0,196 0,433 0,629 inch inch 0,42 0,11 0,11 0,11 0,669 0,834 1,043 1,307 inch inch 0,787 0,866 1,181 1,74 0,787 0,866 1,181 1,692 inch D inch 1,94 1,7 1,866 2,173 0,866 0,964 1,299 1,71 BNEM-01 BNEM-02 BNEM-03 BNEM-04 Box/Min.OQ 300 160
EMC 3 CABLE GLANDS New generation of EMC and Derivation Gland The new generation of Bimed s EMC and derivation gland shows signi_cant advantages compared to other existing cable glands. The patented contact system inside the gland allows all degrees of freedom which are neccessary to install a cable easily; the cable can be pulled forward and backward inside the gland without damaging the cable shielding. This is realized by specially designed contact elements. This feature is most advantageous when connectorizing the single cores of the cable. Also the cable can easily be rotated inside the gland without damaging the cable shielding most important when installing the gland at an industrial connector. The unique mechanism of the integrated contact system therefore show the following features: For small cable diameters in the lower clamping range of the gland the contact system won t touch the cable braiding during the installation process at all. For bigger cable diameters in the upper clamping range of the gland, the contact system will rotate freely inside the gland together with the cable itself. Only when tightening the cap the contact element will be fixed and will be pressed against the cable shielding to ensure a low resistance electrical contact between gland and cable braiding. Simultaneously IP68 protection class and cable anchorage according to the EN 262 is achieved. This straight forward application and convenient installation of the gland saves a lot of time and therefore a lot of money. Shielding and derivation tests performed with this gland show exceptional values. So this EMC and derivation gland from Bime will be used wherever an outstanding performance is needed. Simple application, fast installation together with the patented contact system makes Bimed s gland unique among the cable glands. EMC 3 SERIES INTRO
EMC 3 SERIES EURO METRIC TREAD CABLE GLANDS BMEM-E - C up to + C -40 C up to +1 C EN 60423 D Fast and easy installation. Adapts to different cable shields. Reliable connection. igh shielding factor. Mechanical values according to EN 262. Clamping range identical to all other Eurometric Bime glands. 360 brand touching. Manufactured according to the requirements of EN 262 Thread Type MX1, MX1, MX1, MX1, Ø min-max mm - 6, -,0 -,0 11,0-1 - 21,0 1-2 27,0-3 Ø min mm 2, 9, 1,0 31,0 mm 7,0 mm,0 1,0 32,0,0 6 mm mm 27,0 3 4 27,0 3 4 6 mm D mm 21,,3 26, 32,7 36,3 44, 1, 2,9, 37,0 48,4 70,0 BMEM-ES BMEM-E1 BMEM-E2 BMEM-E3 BMEM-E4 BMEM-E BMEM-E6 BMEM-E7 Box/Min.OQ 400 2 140
INTRO These cable glands are developed according to end users' requirements. Their features can be summarized as follows: A2 Easy insertion of the cable from the two sides of the gland. Open contact fingers in loose position. Free radial and axial movement of the cable. Easy radial and axial movement of the cable, even in contact position without any damage to the braid with the help of rounded contact finger surfaces. Large contact surfaces of the fingers allow low contact resistance even on loosely woven cable braids (the contact surfaces do not sink into the braided wires). igh contact performance even under vibrating conditions with help of the reduced A2 distance between the "sealing clamping level" and "EMC contact level". As Supplied With Min. Cable Diameter With Cable Diameter EMC 4 SERIES EMC 4 CABLE GLANDS
EMC 4 SERIES METRIC TREAD CABLE GLANDS BMEM-E - C up to + C -40 C up to +300 C EN 60423 Manufactured according to the requirements of EN 262 Thread Type MX1, MX1, MX1, MX1, MX1, Ø min-max mm - 6, -,0 -,0 7, -,0-1 1 -,0-32,0-3 37,0 - Ø min mm 2,0 - - 4, -,0, - 11, 7,0 -,0-1 - 27,0 2-3 - - 4 mm,0 mm 16 32 40 63 63 mm mm,0 7,0 6 7 mm 2 3 32,0 3 42,0,0 7,0 67,0 6,0 BMEM-ES (MT) BMEM-E1 (M16T) BMEM-E2S (MT) BMEM-E2 (MT) BMEM-E3 (MT) BMEM-E4 (M32T) BMEM-E (M40T) BMEM-E6 (MT) BMEM-E7 (M63T) BMEM-E7L (M63T) 2 Box/Min. OQ 600 400 2 140
PG TREAD CABLE GLANDS EMC 4 SERIES BSEM-E - C up to + C -40 C up to +300 C DIN 40430 Manufactured according to the requirements of EN 262 These ranges are not keeped in our stocks and can be produced only for pcs as MOQ. Thread Type Pg7 Pg9 Pg11 Pg1 Pg16 Pg21 Pg29 Pg36 Pg42 Pg48 Ø min-max mm - 6, - -,0 -,0 7, -,0-1 1 -,0-32,0-3 Ø min mm 2,0 - - - 4, -,0, - 11, 7,0 -,0-1 - 27,0 2-3 - mm mm,, 18,60,40 22, 28,30 37,00 47,00 0 9,30 mm mm,0,0 60,0 6 mm 2 2 2 3 41,0 4 4 2,0 BSEM-E1(Pg7T) BSEM-E2 (Pg9T) BSEM-E3(Pg11T) BSEM-E4(Pg1T) BSEM-E (Pg16T) BSEM-E6 (Pg21T) BSEM-E7 (Pg29T) BSEM-E8 (Pg36T) BSEM-E9 (Pg42T) BSEM-E0 (Pg48T) Box/Min. OQ 00 600 400 2 140
BNEM-E EMC 4 SERIES NPT TREAD CABLE GLANDS - C up to + C -40 C up to +300 C ANSI B1..1 Manufactured according to the requirements of EN 262 These ranges are not keeped in our stocks and can be produced only for pcs as MOQ. Thread Type NPT 1/4" NPT 3/8" NPT 1/2" NPT 1/2" NPT 3/4" NPT 1" NPT 1 1/4" NPT 1 1/2" NPT 2" Ø min-max inch 0,118-0, 0,196-0,393 0,236-0,4 0,29-0,1 0,393-0,708 0,629-0,984 0,866-1,9 1,181-1,889 1,338-1,732 Ø min inch 0,078-0,196 0,137-0,314 0,177-0,393 0,216-0,42 0,27-0,1 0,4-0,787 0,708-1,062 1,023-1,338 1,181-1,74 inch 0,236 0,236 0,314 0,314 0,314 0,34 0,34 0,34 0,1 inch inch 0,1 0,787 0,866 0,944 1,181 1,74 1,968 2,283 2,19 0,1 0,787 0,866 0,944 1,181 1,74 1,968 2,362 2,677 inch 1,2 1,338 1,9 1,496 1,63 1,968 2,244 2,637 2,716 BNEM-ES (NPT1/4"T) BNEM-E1 (NPT3/8"T) BNEM-E2S (NPT1/2"T) BNEM-E2 (NPT1/2"T) BNEM-E3 (NPT3/4"T) BNEM-E4 (NPT1"T) BNEM-E (NPT1 1/4"T) BNEM-E6 (NPT1 1/2"T) BNEM-E7 (NPT2"T) Box/Min. OQ 600 400 2 140
Lock Nut STANDARD SERIES LOCK NUTS BMBL-BSL-BPFL SW D Thread Type SW mm Metric Thread (Attachment thread : EN 60423) MX1, 19 MX1, 24 MX1, 30 36 46 MX1, 60 70 MX2,0 77 M7X2,0 80 M80X2,0 90 M8X2,0 9 M90X2,0 Pg Thread (Attachment thread : DIN 40430) Pg 7 Pg 9 18 Pg 11 21 Pg 1 23 Pg 16 26 Pg 21 32 Pg 29 41 Pg 36 1 Pg 42 60 Pg 48 64 G(Pf) Thread (Attachment thread : DIN ISO 228) G 3/8" 22 G 1/2" 27 G 3/4" 33 G 1" 43 mm D mm 2,8 7,0 7,0 16,6 21,0 26, 39, 1,0 6 77,0 8 89,6 99,3 6,2 1,0 BMBL-01 BMBL-02 BMBL-03 BMBL-04 BMBL-0 BMBL-06 BMBL-07 BMBL-08 BMBL-09 BMBL- BMBL-11 BMBL- BMBL-13 2,8 2,8, 16,6 2, 2 3, 4 6 70, BSL-01 BSL-02 BSL-03 BSL-04 BSL-0 BSL-06 BSL-07 BSL-08 BSL-09 BSL- 36, 46, BPFL-01 BPFL-02 BPFL-03 BPFL-04
BMEL-BSEL EMC SERIES LOCK NUTS Lock Nut Special design shape for painted enclosures. SW D Thread Type SW mm Metric Thread (Attachment thread : EN 60423) MX1, MX1, MX1, MX1, Pg Thread (Attachment thread : DIN 40430) Pg7 Pg9 Pg11 Pg1 Pg16 Pg21 Pg29 Pg36 Pg42 Pg48 mm D mm 19 24 30 36 46 60 70 3,3 4,6,6 6,7 16,6 21,0 26, 39, 1,0 6 77,0 BMEL-01 BMEL-02 BMEL-03 BMEL-04 BMEL-0 BMEL-06 BMEL-07 BMEL-08 18 21 23 26 32 41 1 60 64 3,3 3,3 4,6,6,6 6,1 16,6 2, 2 3, 4 6 70, BSEL-01 BSEL-02 BSEL-03 BSEL-04 BSEL-0 BSEL-06 BSEL-07 BSEL-08 BSEL-09 BSEL-