Douglas Lighting Controls Bluetooth Commissioning and Room Control App BT-APP Field Manual *Patent Pending
Table of Contents 1. GENERAL DESCRIPTION Page 3 2. SYSTEM REQUIREMENTS Page 3 3. SYSTEM SETUP Page 4 ASSOCIATE DEVICES Page 6 4. SETUP ROOM Page 8 5. DEVICE SETUP Page 11 SETUP DIMMER SWITCH Page 12 SETUP 4-BUTTON SWITCH Page 13 SETUP 8-BUTTON SWITCH Page 14 SETUP OCCUPANCY DAYLIGHT SENSOR Page 15 SETUP GATEWAY Page 16 6. SETUP ROOM CONTROL Page 17 Page 2
1. GENERAL DESCRIPTION The Douglas Lighting Controls Bluetooth App for Commissioning and Room Control is available for ios devices (ipod, iphone) by download through the Apple App Store. The App provides users with an easy to use field tool for commissioning Douglas Lighting Controls Bluetooth Wireless system and included an end user App for controlling lights. Commissionable Devices BT-PP20-A BT-8BTSW-U-A BT-8BTSW-3-A BT-4BTSW-U-A BT-4BTSW-3-A BT-DMSW-U-A BT-DMSW-3-A BT-WOR-A BT-GTWY-A BT-FMS-A (only functions as a stand-alone device or with other BT-FMS units) 2. SYSTEM REQUIREMENTS A dedicated ios device to commission system, save, and store system parameters ipod Gen 6 or newer and ios 10.x or higher iphone 6 or newer and ios 10.x or higher Before You Start A best practise is to use a dedicated ipod or iphone as the projects system set-up device rather than a personal smartphone as the system settings stay with the Apple ID. When setting up the ios device Apple ID, icloud account, and network access, chose names carefully, record accurately, and store in a reliable location. Once a Fixture Controller & Sensor has been added to a network (associated), do not remove (disassociate) it before ensuring it is connected to, and communicating with, the system set-up device. Page 3
3. SYSTEM SETUP Process 1. Download App 2. Select Set-up Network 3. Associate First Device, Setup Device and Room 4. Set Up Other Devices (Occupancy Sensor Last) 5. Select Room Control to Control a Room via App Overview Douglas Lighting Controls recommends using a project-dedicated device, not one which is used for personal and/or other company data and communications. Details on icloud accounts, including instructions for setup, can be found at www.apple.com/icloud. An ios device with icloud account is needed to download the App and to back up the system parameters on icloud. Each icloud account can have only one instance of the App, and the App can create and maintain only one database. A database stores the system parameters. The database is identified by the Network Key and accessed using the Admin Password (both values are entered during system set-up). After an ios device is configured with an icloud account and the App downloaded, the system set-up process can begin. First, system parameters are entered. These include: Site Name Network Key Admin Password Record this information accurately and store in a reliable location. These parameters are critical to accessing the system. A good method for recording this information is screen capture the network setup page. To take a screen shot, press and hold the ON/OFF button, then momentarily press the Home button. The screen capture will be saved as an image accessible via the Photos icon. The screen capture can then be emailed to a few people for recovery purposes. Again, it is very important to keep track of this data and of the ios device itself. Spatial organization A Douglas Lighting Controls Bluetooth wireless network can have multiple rooms and each room can have up to eight lighting zones. Rooms and Zones are defined in the system set-up. Review your floor plans to find, and if needed, develop a room and zone plan 1. DOWNLOAD APP Visit the Apple App store and search for Douglas Lighting Controls Access Douglas Lighting Controls BTCC App Page 4
3. SYSTEM SETUP 2. SYSTEM SETUP System Setup Ensure your Smartphone s Bluetooth is ON Open App Select System Setup (bottom right) System Setup Enter information save this information you will need it later. It cannot be retrieved if lost or forgotten. Tip: screen capture your System Setup > press and hold Power, then press Home button Press Done (upper right) Page 5
3. SYSTEM SETUP 3. ASSOCIATE DEVICES Press + to find unassociated devices Tip: set up the Occupancy/Daylight sensors last Select device to be associated to network Devices will identify themselves when selected: Switches: Bottom LEDs will flash Orange Sensor: LED will flash Orange Controller: fixture(s) will flash and LED will flash Orange Press upload icon to add device to room Page 6
3. SYSTEM SETUP Associate Device Enter Device Name TIP: use device type and location Note: Device Names are tested to avoid duplication Press OK Associate Device Device is now Associated and shown in list -> since the device has yet to be setup, Room is listed as Global Press cog wheel to continue with device setup Page 7
4. SETUP ROOM Setup Room Press > to setup room Setup Room Press + to add Room If rooms have already been created, they will be listed. If so, press the room you d like press Select Page 8
4. SETUP ROOM Setup Room Enter Room Name Set Timeouts Occupancy 15s, 5m, 10m, 20m, 30m, 45m Quiet Mode 30s, 30m, 60m, 90m, 120m, 150, 180m Occupancy Mode Occupancy (Auto ON/Auto OFF) Vacancy (Manual ON/Auto OFF) None (to use as daylight sensor only) Full (high light level) Partial (Auto ON @ 50%, wall switch needed for HIGH light level) Zone Settings Select Zone Settings to define the lighting ZONES within the room Note: multiple controllers (BT-PP20), and therefore multiple fixtures, can be assigned to the same ZONE Zone Settings (8 max.) Up to eight (8) zones (Z 1 through Z 8) can be defined in a room Zones can be named by tapping Zone field Dimming Min. & Max. levels (Low & High trim) can be adjusted Press the circle in the rightmost column to enable selected zones Press Done to return to the edit room page Page 9
4. SETUP ROOM Setup Room Select Scene Settings Scenes Settings (6 max.) Default shown below Press SCENE Name to Edit NOTE: SCENE Names show in Wall Station setup screens Activate the desired SCENE by activating check mark Press Config to adjust the SCENE Scenes Settings Set SCENE by activating the desired ZONE (1-8) and adjusting the Zone s DIM Level Slider and ON/OFF button Press Done Repeat for other SCENES Done > Done > Done to return to Device setup page Complete Device setup Page 10
5. DEVICE SETUP Setup: Controller After adding the device to a room, continue with device setup Edit parameters in grey boxes (other parameters are edited in Room Setup) Select Zones: 1 to 8 or as labelled in Room Setup Select Daylight Sensor: None - no daylight available to this Zone Sensor 1 when daylight/window is available to this Zone Sensor 2 when window AND a SKYLIGHT are present in this Zone, use for the second sensor near Skylight Daylight Area: None/Primary/Secondary Scroll down for more items Emergency Pack: ON if controlling Emergency Light Database Device: Always OFF TTL: Always 2 Test Emergency Mode Press Write All Parameters to Save Then, Cancel to go back to Associated Device List Page 11
5. DEVICE SETUP Setup: Dimmer Switch After adding the device to a room, continue with device setup Enter parameters in grey boxes all other parameters are edited in Room Set-up Select Zones: 1 to 8 or as labelled in Room Setup Daylight Sensor None - no daylight available to this Zone Sensor 1 when daylight/window is available to this Zone Sensor 2 when window AND a SKYLIGHT are present in this Zone, use for the second sensor near Skylight Scroll down for more items TTL: Always 2 Press Write All Params to Save Cancel to go back to Associated Device List Page 12
5. DEVICE SETUP Setup: 4-button Switch After adding the device to a room, continue with device setup Select Button to define action Select ZONE, then action or preset for this ZONE DIM UP DIM DOWN ON OFF TOGGLE Preset (configured in Edit Room Setup page) Cancel to go back and set other buttons Press Write All Params to Save Page 13
5. DEVICE SETUP Setup: 8-button Switch After adding the device to a room, continue with device setup Select Button to define action Select ZONE, then action or preset for this ZONE DIM UP DIM DOWN ON OFF TOGGLE Preset (configured in Edit Room Setup page) Cancel to go back and set other buttons Press Write All Params to Save Page 14
5. DEVICE SETUP Setup: Occupancy Daylight Sensor After adding the device to a room, continue with device setup Select Zones that Sensor will Control: None, 1 to 8, All Secondary Occupancy When Bluetooth is on and Room Control App is in use, secondary occupancy is managed by Bluetooth proximity to Sensor Daylight Sensor None Occupancy sensor ONLY, no daylight available to this Zone Sensor 1 when daylight/window is available to this Zone Sensor 2 when window AND a SKYLIGHT are present in this Zone, use for the second sensor near Skylight Secondary Daylighting If you have a controllers in the same zone and want primary and secondary Daylight Zone (secondary zone is dimmer by 50% of the dimming of the primary zone) Scroll down for more items Daylight Setpoint (lux) Default 300 Daylight Control For Daylight Harvesting TTL: Always 2 Press Write All Params to Save Cancel to go back Page 15
5. DEVICE SETUP Setup: Gateway Dialog Base Address Room 1 Room 2 Room 3 Room 4 Dialog Base Address TTL: Always 2 Write All Params Cancel to go back Page 16
6. SETUP ROOM CONTROL Setup: Room Control See office or Building Manager for parameters Enter parameters Press DONE Control up to 4 Zones in a room (screen us non-editable) Page 17
toll free: 877-873-2797 direct: 604-873-2797 lighting@douglaslightingcontrols.com www.douglaslightingcontrols.com Your Douglas Lighting Controls representative: The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Douglas Lighting Controls is under license. Other trademarks and trade names are those of their respective owners. LIT#: AT-APP-FM062618 A member of the Panasonic Group