INSTRUCTION AND MAINTENANCE VIDEO MOTORE PROJECTION SCREEN 1.1 TECHNICAL DATA PRODUCT DESCRIPTION Screens made with the following projection fabrics: SOFT WHITE, MATT WHITE SOFT, SOFT WHITE TRANSOUND, RETRO (see technical pages 5/6/7) In the standard version, the screen is lowered from the front side of the box, by wall installation the fabric will descend at a distance from the same of mm 81.5 to 97.5, on request, the screen can be provided with rear lowering system, in this case the fabric will be at a wall distance of approximately 22.5 to 16.5 mm - Screen case of extruded aluminium, powder coated in white RAL 9010, section 85x93 mm with rounded corners on the upper ribs suitable for the fixation of hooking brackets; on the bottom part longitudinal slot with rounded edges, through which the projection fabric descends, Internal tube for the screen rewinding, of anodized aluminium silver Ø 60 mm, which incorporates the electric motor on special silent-block rubber Single phase electric motor, IMQ, CE, 5- year warranty from date of purchase, supply 200V - 50Hz, 0.5 A absorption, degree of protection IP 44, 17 RPM, in the standard version the motor is mounted on the left side screen up and down electric inverter standard supplied. Screen up and down limit switches factory adjusted, possibility of different settings if necessary. The screen can also be stopped at intermediate height by pressing the electric inverter switch - Suspension brackets are standard supplied and can be mounted anywhere along the whole housing length. Brackets are steel made, epoxy powder coated in white RAL 9010, suitable both for wall or ceiling installation thanks specific expansion anchors - Screen case end caps steel epoxy coated in white RAL 9010 Robust individual packing in double cardboard type Volcano - Product CE certified, full warranty 24 months as specified on the operating and maintenance manual- Optional accessories: radio remote control, spacing brackets - Box dimensions: size of the base of the canvas +7 cm 1
1.1.1 ELECTRIC CONTROL MOTOR SINGLE PHASE Standard voltage 230 V - 50 HZNormal power 120 W Power consumption 0.5 A Degree of protection IP 44 17 rpm Normal torque 6 Nm Approval "IMQ" 1.1.2 ELECTRIC UP-DOWN INVERTER 10 A Section output engine cables N. 4 x 1,5mq Power supply cable PHASE + NEUTRAL + EARTH sect. 1,5 mm POWER SUPPLY 220 VOLT - 50 HERTZ 1.1.3 REMOTE CONTROL (if any) Operating frequency: 433.920 Mhz Coding System: self code learning N. of codes to be memorized: 1000 for each receiver Capacity (BROWN) Impedance 50 Ohm Receipt range capacity: 40 m ca. (Please note that the value is to be considered guidance and can be influenced by barriers, metal structures, electromagnetic fields etc.). - Supply voltage 230 V aprox. - Power consumption 1.5 W MAX - Operating temperature - 10 to + 55 C 2
1.1.4 ELECTRICAL WIRING DIAGRAM FOR INVERTER SWITCH MOTORE = MOTOR POWER MORSETTI = WIRING TERMINALS 2 BLUE 3 YELLOW GREEN 4 BLACK OR BROWN 5 BLACK OR BROWN 1 PHASE 2 NEUTRAL 3 GROUND - Disconnect mains power prior to any operation - After installation you should not operate any traction on the terminals - Connect the grounding wires before the phase and neutral 3
1.1.5 WIRING FOR REMOTE CONTROL To install the unit, proceed as follows: a) prepare the Jumper b) connect the power supply and the motor (with the limit switches) c) if required, connect the manual wall switches open/close 4
1.2 PROJECTION FABRIC PVC projection fabric, thickness 400 MY, height. 2400, cadmium free, type fire proof class M1, as per french definition and in compliance with EEC 91/338. Light white colour with a smooth side, rear of the screen not to be used and a satin finish side for projections. In the standard version, front screen lowering from the screen case, consequently wall distance about mm. 81.5-97.5 in the case of wall fixation, on request, it can be supplied with rear lowering system, in this case wall distance will be mm. 22.5 to 16.5. The projection canvas is rolled on a silver anodized round aluminium tube, section dia.mm.60, which integrates the electric motor. For best viewing, it is recommended to unroll the screen at least few hours before projection start to allow the canvas to perform its best planarity. FRONT LOWERING (WALL DISPLACED) REAR LOWERING (CLOSE TO THE WALL) 5
1.3 ALUMINIUM CASE Extruded aluminium casing powder coated in light grey RAL 7035, section mm. 85x93 with rounded corners, upper ribs with appropriate hooking brackets, longitudinal slot with rounded edges, through which the projection canvas is lowered, on the bottom left side of the screen case, two holes enable the access to the canvas raising/lowering adjustment screws. 2.0 SAFETY 2.1 SAFETY CRITERIA ADOPTED The cables supplied are contained in a single housing of self-extinguishing plastic, however, wall or ceiling mounting must comply with the law 46/90 and be conducted by appropriate staff. In case of failure of one of the two limit adjustment screws, on the electric motor, there is a thermal switch capable to open the electrical circuit. The whole equipment was designed for maximum safety. 2.2 SAFETY COMPONENTS The adopted safety components are: Robust suspension brackets widely oversized thermal electric switch in case of failure of one of the two limits. No sharp corners or sharp edges which could cause injury 6
3.0 INSTALLATION The installation of this type of screens can be to wall or to the ceiling. 3.1 INSTALLATION INSTRUCTION To make a correct installation, position the two suspension brackets in such a way that the screen is suspended about 1 / 15 of its length, measured from one of the two terminal heads. Fix the brackets to obtain an alignment as accurate as possible. Use reliable anchors and appropriate to the wall, minimum recommended size diameter mm. 8. IMPORTANT! Make sure that wall or ceiling are appropriate to support the declared weight and to the installation through screw anchors. When in doubt, use chemical fixings type. Once brackets are fixed, lift up the screen and attach it on the appropriate tab of the bracket, then slightly tighten the front screw and tighten the lock bolt. This must be done by two people, one from the left side, the other from the right side. IMPORTANT! Choose walls with a flat surface, otherwise the bracket tag will not ensure the suspension of the screen. 7
4.0 OPERATION 4.1 GENERAL DESCRIPTION After the electrical connections, make sure of the exact voltage of the power supply, close the circuit and giving power and operate with short pulses on the inverter "Lowering." Make sure everything runs properly and then operate few times the up/down mechanism. At this point the operation was well performed. 5.0 USE 5.1 SETTING THE LIMIT SWITCHES The only adjustment to be made is that of the two up and down switches up of the projection screen. These two elements are already set during production, by the manufacturer. However, you can make some adjustments by turning the two limit switches screws, which can be reached by introducing a 4 mm hexagonal key standard supplied - in the two holes on the bottom of the screen case. IMPORTANT! Do not unroll the canvas over the measurement specified for each type of screen: increasing the descent above this size could damage the screen or cause its fall off, such damages are not covered by warranty and are not under the responsibility of the manufacturer. Likewise, do not force the rewinding of the canvas after it has been completely rolled up as this would force the electric motor and the counter weight tube could get stacked into the box and consequently get damaged. 8
Setting the upper limit switch - Bring the canvas to the maximum upper position, then stop the movement by pressing STOP button (centre position) - Insert the 4 mm hexagonal screw (standard supplied) in the 1st hole near the opening of the descent of the canvas, turn the screw counter-clockwise = more winding-up, clockwise = less winding-up. Each turn of the screw is approximately mm. 35 displacement of the canvas. Setting the lower limit switch - Bring the canvas to the maximum lower position, then stop the movement by pressing STOP button (centre position) - Insert the 4 mm hexagonal screw (standard supplied) in the 2nd hole (the farthest one from the canvas), turn the screw counter-clockwise = more descent, clockwise = less descent. DISCESA = DOWN SALITA = UP LATO PROIEZIONE = PROJECTION SIDE 9
5.2 RECOMMENDATIONS AND PROHIBITION It is forbidden the use of the screen by persons below 16 years of age or disabled or otherwise altered in their operational ability. It also prohibited the installation on precarious, unstable and uneven walls. Environments with high humidity, dusty, in the presence of explosive mixtures. It is not recommended the screen continue exposure to sunlight, which could alter the original colour of the canvas. Do not expose the screen to temperatures above 50 C, this could cause irreparable damages. In case of malfunction of the motor, do not force manually the output of the canvas, but call service. Do not adjust the limit switches continuously and without any real necessity. 10