FULL AHD IR LED Dome Camera User Manual M262-ATR522-001 Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CONTENTS 1. NOTICES 2. FOR YOUR SAFETY 3. FEATURES 4. EQUIPMENT AND ACCESSORIES 5. OVERVIEW AND FUNCTION 6. INSTALLATION 7. CONNECTION 8. DIMENSIONS 9. SPECIFICATION 10. OSD MENU STRUCTURE 11. AHD UTC (UP THE COAX) CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Use Class 2 Power Supply Only 2
1. NOTICES This device complies with Part 15 of FCC regulations. Operation is subject to the following two conditions: 1. This device may cause harmful interference. 2. This device may receive interference that can cause affect the operation of this equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference problems at his or her own expense. Caution Alteration or modifications carried out without. appropriate authorization may invalidate the user's right to operate the equipment. 1. A regulated DC12V 500mA power supply is recommended to ensure the best picture quality and stable operation. An unregulated power supply may cause damage to the camera. Using an unregulated power supply will void the product warranty. If your monitor is switched to high impedance, then please adjust accordingly. 2. Do not attempt to disassemble the camera to access internal components. Refer servicing to your dealer. 3. Never face the camera towards the sun or any bright or reflective light, which may cause smear on the picture and possible damage to the image sensor. 4. Do not remove the serial sticker for the warranty service. 3
1. NOTICES WEEE (Waste Electrical & Electronic Equipment) This marking shown on the product or its remove, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how to safely recycle the item. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 4
2. FOR YOUR SAFETY 1) All warning and instruductions in this manual should be followed. 2) Save this manual for future reference. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) To help prevent from electric shock, plug the equipment and peripheral power cables into properly polarized or grounded electrical outlets. These cables are equipped with the wide blade or the third prong to ensure proper grounding. Do not use adapter plug or remove the ground prong from a cable. If the provided plug does not fit your outlet, consult an electrician. 10) Ensure that nothing rests on your equipment's cable and that the cables are not located where they can be stpped on, trapped over, or pinched. 11) Only use attachments or accessories as specified. 12) Only use the equipment with the cart, stand, tripod, bracket, or table that is specified by the manufacturer or sold with the apparatus. When a cart is used, use caution to prevent the cart from tipping over and to avoid injury. 13) Do not connect or disconnect during lighting storms due to risk of electric shock. 14) If any of the following conditions occur, unplug the equipment from the electrical outlet and replace the part or contact your trained service provider: The power cable, extension cable, or plug is damaged. An object has fallen into the equipment. The equipment has been exposed to water. The equipment has been dropped or damaged. The equipment does not operate correctly when you follow the operating instructions. 5
3. FEATURES High resolution SONY 1/2.8" 2.1MP Progressive Color CMOS Image Sensor, 1080p(1920x1080)@30fps Support various digital video output 1080p@30fps / 1080p@25fps / 720P@30fps / 720p@25fps AHD(Analog HD) Output AHD is suitable for long reach transmission over single coaxial cable. Transmission Distance: 300 m (Color) Max. Transmission Distance: 500 m OSD menu for setup and configuration. 20 long life IR illuminators for 0 Lux viewing performance and range to 20 m (66 ft.) Provides True Day/Night capability with motorized IR cut filter. Power source: 12VDC 3-Axis gimbal IP66 Waterproof construction. UTC (Up the coax.) via AHD coaxial cable. 6
4. EQUIPMENT AND ACCESSORIES Camera Manual Template Screws, Set Screw / L-Wrench / Plastic Anchors Plastic Anchors Screws L-Wrench Set Screw 7
5. CAMERA COMPONENT DESCRIPTIONS Housing Ball Photo Cell Housing Ball Bracket IR LED Housing Top Housing Bottom 8
6. INSTALLATION Template 70 140 70 Plastic Anchors (4ea) Tapping Screws-4x25L (4ea) Open Close Set Screw-M2.5x3L (1ea) 9 L-Wrench
7. CONNECTION MONITOR CONNECTION When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems. 10
8. DIMENSIONS Unit(mm) Ø 93 20-IR LED Ø 69 77 (The maximum rotation) 63 4-Ø4.5 Ø68.5 11
9. SPECIFICATION Image Device 1/2.8 PROGRESSIVE SCAN SONY CMOS Effective Pixels 1984 (H) x 1105 (V) Unit cell size 2.8um (H) x 2.8um (V) Video output AHD : 1080p 30fps(25fps) / 720p 30fps (25fps) Transmission Distance AHD : Color 300m@RG59, BW 500m@RG59 Minimum Illumination 0 Lux (with IR LED on) Auto / Manual selectable Shutter speed 1/30(25), 1/60(50), FLK, 1/240(200), 1/480(400), 1/1000, 1/2000, 1/5000, 1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30 Day/Night True D/N with ICR Mechanism BLC 12 OFF/ BLC/ HSBLC AGC 0 ~ 15 2/3DNR Digital WDR OFF / LOW / MIDDLE / HIGH OFF/ ON(LEVEL)/ AUTO SENS-UP OFF/ AUTO(X2, X4, X6, X8, X10, X15, X20, X25, X30) Privacy Masking Motion Detection White Balance Lens OSD Language ETC IR LED 4 Zones 4 Zones AWB/ATW/ PUSH LOCK/ INDOOR/ OUTDOOR/ MANUAL Fixed Board Lens Coaxial communication(pelco-c) English, Korean, Japanese, Chinese, Russian, French, Spanish, Italian, Portuguese, Dutch, German, Polish, Turkish, Hebrew, Arabic FLIP(H/V/HV), Defog, FREEZE, SHARPNESS, LSC 850nm, 20ea IR LED Distance Up to 20M IP Rating IP66 Operating Temperature 14 F~122 F(-10 C ~ 50 C) Storage Temperature -4 F~140 F(-20 C ~ 60 C) Humidity Less than 80% Power Consumption 12VDC(±10%), Max. 320mA Dimension Ø93 * 63 Weight Approx. 332g *Specifications and designs are subject to change for improving the functionality of this product without notice.
10. OSD MENU STRUCTURE Main 1st Sub Menu 2nd Sub Menu Value LENS EXPOSURE BACKLIGHT MANUAL AUTO, 1/30(25), 1/60(50), FLK, 1/240(200), 1/480(400), 1/1000, SHUTTER 1/2000, 1/5000, 1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30 AGC 0~15 SENS-UP OFF/ AUTO(X2, X4, X6, X8, X10, X15, X20, X25, X30) BRIGHTNESS 1 ~ 100 D-WDR OFF/ ON(LEVEL)/ AUTO DEFOG OFF/ AUTO(POS/SIZE, GRADATION, DEFAULT) OFF BLC HSBLC LEVEL LOW/ MIDDLE/ HIGH AREA POSITION, SIZE DEFAULT SELECT AREA1/ AREA2/ AREA3/ AREA4 DISPLAY OFF/ ON(POSITION, SIZE) BLACK MASK OFF/ ON LEVEL 0~100 MODE ALL DAY/ NIGHT(AGC LEVEL) WHITE BALANCE DAY&NIGHT NR DEFAULT AWB ATW AWC(PUSH) INDOOR OUTDOOR BLUE 0~100 MANUAL RED 0~100 D N(CDS) 0~255 D N(DELAY) 0~ 60sec, 1sec/step AUTO N D(CDS) 0~255 N D(DELAY) 0~ 60sec, 1sec/step COLOR BURST OFF/ ON B/W IR SMART OFF/ ON EXT D N(DELAY) 1 ~ 60sec, 1sec/step N D(DELAY) 1 ~ 60sec, 1sec/step 2DNR OFF/ LOW/ MIDDLE/ HIGH 3DNR OFF/ LOW/ MIDDLE/ HIGH 13
10. OSD MENU STRUCTURE Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu CAM TITLE D-EFFECT OFF ON FREEZE MIRROR NEG. IMAGE SELECT DISPLAY 0~9, A~Z, Special Character OFF/ ON OFF/MIRROR/ V-FLIP/ ROTATE OFF/ ON AREA1/ AREA2/ AREA3/ AREA4 OFF/ ON(POSITION, SIZE) SENSITIVITY 0~100 MOTION COLOR WHITE/ RED/ GREEN/ BLUE TRANS 0.00/ 0.25/ 0.75/ 1.0 ALARM VIEW TYPE/ OSD VIEW/ ALARM OUT/ TIME SPECIAL DEFAULT SELECT DISPLAY AREA1/ AREA2/ AREA3/ AREA4 OFF/ MOSAIC/ INV/ COLOR PRIVACY COLOR WHITE/ BLACK/ RED/ BLUE/ YELLOW/ GREEN/ CYAN/ USER TRANS 0.25/ 0.50/ 0.75/ 1.0 DEFAULT LANGUAGE ENG/ CHN/ CHN(S)/ GER/ FRA/ ITA/ SPA/ POL/ RUS/ POR/ NED/ TUR/ KOR/ JPN/ HEB/ ARB DEFECT LIVE DPC WHITE DPC BLACK DPC OFF/ ON(AGC LEVEL / LEVEL) POS/SIZE, START, DPC VIEW,LEVEL, AGC, SENS-UP POS/SIZE, START, DPC VIEW,LEVEL CAM ID 0~255 RS485 ID DISPLAY OFF/ ON BAUDRATE 2400/ 4800/ 9600/ 19200/ 38400 14
10. OSD MENU STRUCTURE Main 1st Sub Menu 2nd Sub Menu 3rd Sub Menu LEVEL 0~10 SHARPNESS START AGC 0~255 END AGC 0~255 LCD GAMMA/ BLUE GAIN/ RED GAIN MONITOR ADJUST CRT BLUE GAIN/ RED GAIN LSC OFF/ ON VIDEO.OUT NTSC/ PAL OUTPUT_SIZE 1080P 720P EXIT SAVE&END/ RESET/ NOT SAVE * Changing the ADJUST / VIDEO OUT from the default settings may cause the VIDEO BLACKOUT. (In case of setting "Adjust/VIDEO OUT" mode in the menu, it may cause "VIDEO Black out" in DVR. For the settlement, the "VIDEO OUT" setting should be set compatible with the camera. * Reset of camera will make initial value as factory reset.) * DAY&NIGHT / EXT function is NOT operable. * SPECIAL / RS485 NOT operable. * SPECIAL / MOTION / ALARM / ALARM OUT, TIME function is NOT operable. 15
11. UTC (UP THE COAX) The UTC function supports OSD control via AHD coaxial cable. Important) * When low quality coaxial cable is used, it may not be possible to control OSD menu. 16