T541 Flat Panel Montor User Gude ENGLISH
Frst Edton (June / 2002) Note : For mportant nformaton, refer to the Montor Safety and Warranty manual that comes wth ths montor. Ths publcaton could contan techncal naccuraces or typographcal errors. Changes are made perodcally to the nformaton heren; these changes wll be made n later edtons. IBM may make mprovements and/or changes n the product(s) and/or program(s) at any tme. It s possble that ths publcaton may contan reference to, or nformaton about, IBM products (machnes and programs), programmng, or servces that are not announced n your country. Requests for copes of ths publcaton and for techncal nformaton about IBM products should be made to your IBM Authorzed Dealer or IBM Retaler. No part of ths publcaton may be reproduced or dstrbuted n any form or by any means wthout pror permsson n wrtng from the Internatonal Busness Machnes Corporaton. Copyrght Internatonal Busness Machnes Corporaton 2002. All rghts reserved. Note to U.S. Government Users -- Documentaton related to restrcted rghts -- Use, duplcaton or dsclosure s subject to restrctons set forth n GSA ADP Schedule Contract wth IBM Corp. Notces References n ths publcaton to IBM products, programs, or servces do not mply that IBM ntends to make these avalable n all countres n whch IBM operates. Any reference to an IBM product, program or servce s not ntended to state or mply that only IBM s product, program, or servce may be used. Any functonally equvalent product, program, or servce that does not nfrnge any of IBM s ntellectual property rghts or other legally protectable rghts may be used nstead of the IBM product, program, or servce. Evaluaton and verfcaton of operaton n conjuncton wth other products, programs, or servces, except those expressly desgnated by IBM, are the user s responsblty. IBM may have patents or pendng patent applcatons coverng subject matter n ths document. The furnshng of ths document does not gve you any lcense to these patents. Trademarks The followng terms, used n ths publcaton, are trademarks or servce marks of the IBM Corporaton n the Unted States, other countres, or both: HelpCenter IBM ENERGY STAR s a U.S. Govt. regstered trademark. Mcrosoft, Wndows, and Wndows NT are trademarks of Mcrosoft Corporaton n the Unted States, other countres, or both. Other company, product, and servce names may be trademarks or servce marks of others.
T541 Flat Panel Montor User Gude Contents ENGLISH Settng up the montor...2 System Hardware Requrements...2 Handlng Instructons...2 Montor Installaton...3 Connectng your Montor...3 Swtchng on your Montor...4 Montor Drver Installaton...5 Drver nstallaton for Wndows 95 or Wndows 98...5 Drver nstallaton for Wndows 2000 or Wndows Me...6 Drver nstallaton for Wndows XP...7 Image Setup for Analog Input...8 Auto Setup...8 AutoSetup for Wndows 3.1, Wndows 95, Wndows 98, Wndows 2000, Wndows Me, Wndows XP or Wndows NT...9 Adjustng the mage settngs n DOS...10 Manually adjustng the mage settngs...11 Ergonomc Consderatons...12 Workplace preparaton...12 Workng Practces...12 Adjustng the Montor Poston...13 Carng for your Montor...13 Adjustng Your LCD Montor...14 User controls...14 On-screen dsplay (OSD) controls...15 Further Informaton...18 Dsplay modes...18 Power Management...19 Troubleshootng...20 Specfcatons...22 1
Settng up the montor System Hardware Requrements Ths montor requres a computer wth a sutable on-board sub-system or Vdeo Adapter card that can support XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz. Handlng Instructons 1. Do not support the montor wthn the screen area. The Lqud Crystal Dsplay s glass and can be damaged by rough handlng or excessve pressure. 2. Before usng your montor for the frst tme, remove the clear protectve flm from the front of the screen. 2
Montor Installaton ENGLISH Connectng your Montor 1. Turn off your computer and all attached devces. Next, unplug the power cord(s) to your computer and all attached devces. 2. Connect the sgnal cable. The analog sgnal cable s already connected to your montor. The analog connector s the blue connector. When connectng the analog sgnal cable (Fgure A) Connect the free end of the attached sgnal cable to the 15-pn Montor port on the computer and tghten screws. (Fgure A) If connectng a DVI-D dgtal sgnal cable (Fgure B) Connect one end of the montor sgnal cable to the whte connector on the rear panel of the montor. Connect the other end to the whte connector on the rear panel of the computer and tghten the screws. Cable not suppled (Optonal) (Fgure B) 3
3. Connect the power cord to the montor and then plug the power cord nto a properly grounded outlet. Next, reconnect the power cord(s) to your computer and all attached devces. Swtchng on your Montor 1. Swtch on your montor by pushng and releasng the power swtch marked [ ] at the front of the bezel. [To swtch off your montor, push and release the power swtch agan.] 2. Swtch on your computer. 3. If you are usng the analog connector, run AUTO SETUP by followng the nstructons n the Auto Setup secton on page 8. 4
Montor Drver Installaton ENGLISH Drver nstallaton for Wndows 95 or Wndows 98 Ths secton must be completed before contnung wth the Wndows95 or Wndows98 Auto Setup on page 9. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. IBM recommends usng ether 1024 x 768 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To use the Plug and Play feature n Mcrosoft Wndows 95 or Wndows 98, fles should be loaded from the IBM Montor CD. 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow the system to boot nto Wndows95 or Wndows98. Your computer s Plug and Play code may warn you that your system hardware has changed. Ths means that t has detected your new montor for the frst tme. 4. Open the DISPLAY PROPERTIES wndow by clckng START, SETTINGS, CONTROL PANEL and then double - clckng on the DISPLAY con. 5. Clck the SETTINGS tab. In case of Wndows 95 : 6-1. Clck the CHANGE DISPLAY TYPE button. 2. Clck the CHANGE MONITOR TYPE button. In case of Wndows 98 : 6-1. Clck the ADVANCED button. 2. Clck the MONITOR tab. 3. Open the UPGRADE DEVICE DRIVER WIZARD wndow by clckng on CHANGE button and then select the NEXT button. 4. Clck the Dsplay a lst of the known drvers for ths devce so that I can choose a specfc drver and then select the NEXT button. 7. Insert the Setup CD nto the CD drver: and clck the HAVE DISK button. 8. Clck OK. 9. Ensure that the CD drve letter s selected, and then select the Drvers folder. 10.Choose IBM T541 montor and Clck OK. The fles wll be coped from the CD to your hard dsk drve. 11.Close all open wndows and remove the CD. 12.Restart the system. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 5
Drver Installaton for Wndows 2000 or Wndows Me Ths secton must be completed before contnung wth the Wndows2000,Wndows Me Auto Setup on page 9. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. IBM recommends usng ether 1024 x 768 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To use the Plug and Play feature n Mcrosoft Wndows 2000 or Mcrosoft Wndows Mllennum Edton(Me) fles should be loaded from the IBM Montor CD. 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow the system to boot nto Wndows 2000 or Wndows Me. 4. Open the DISPLAY PROPERTIES wndow by clckng START, SETTINGS, CONTROL PANEL and then double-clckng the DISPLAY con. 5. Clck the SETTINGS tab. 6. Clck the ADVANCED button. 7. Clck the MONITOR tab. 8. Clck the PROPERTIES button. 9. Clck the DRIVER tab. 10.Open the UPGRADE DEVICE DRIVER WIZARD wndow by clckng on UPDATE DRIVER and then Clck the NEXT button. 11.Select the Dsplay a lst of the known drvers for ths devce so that I can choose a specfc drver and then Clck the NEXT button. 12.Insert the Setup CD nto the CD drve : and clck the HAVE DISK button. 13.Clck OK. 14.Ensure that the CD drve letter s selected, and then select the Drvers folder. 15.Choose IBM T541 montor and Clck OK. The fles wll be coped from the CD to your hard dsk drve. 16.Close all open wndows and remove the CD. 17.Restart the system. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 6
ENGLISH Drver Installaton for Wndows XP Ths secton must be completed before contnung wth the Wndows XP Auto Setup on page 9. On LCD montors, unlke CRTs, a faster refresh rate does not mprove dsplay qualty. IBM recommends usng ether 1024 x 1768 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To use the Plug and Play feature n Mcrosoft Wndows XP fles should be loaded from the IBM Montor CD. 1. Turn off the computer and all attached devces. 2. Ensure that the montor s connected correctly. 3. Turn on the montor and then the system unt. Allow the system to boot nto Wndows XP. 4. Open the DISPLAY PROPERTIES wndow by clckng START, SETTINGS, CONTROL PANEL and then double-clckng the DISPLAY con. 5. Clck the SETTINGS tab. 6. Clck the ADVANCED button. 7. Clck the MONITOR tab. 8. Clck the PROPERTIES button. 9. Clck the DRIVER tab. 10.Open the Hardware Update Wzard wndow by clckng on UPDATE DRIVER and then Clck the NEXT button. 11.Select the Install from a lst or Specfc locaton(advanced) and then Clck the NEXT button. 12.Insert the Setup CD nto the CD drve : and clck the HAVE DISK button. 13.Clck OK. 14.Ensure that the CD drve letter s selected, and then select the Drvers folder. 15.Choose IBM T541 montor and Clck OK. The fles wll be coped from the CD to your hard dsk drve. 16.Close all open wndows and remove the CD. 17.Restart the system. The system wll automatcally select the maxmum refresh rate and correspondng Color Matchng Profles. 7
Image Setup for analog nput Auto Setup Before carryng out ths secton, t s very mportant that the correct montor drvers have been nstalled.(see pages 5 and 7) The Setup Utlty ncluded on the setup CD dsplays a test pattern of dots. It does not replace or modfy the dsplay drvers. The Auto Setup nstructons requre the montor to be warmed up for 15 mnutes. Ths s not requred for normal operaton. If your computer does not run wth the setup CD shpped wth the montor, refer to Manual Setup on page 11. The AUTO SETUP process only apples to the current screen mode. When a new mode s selected, repeat ths secton to reset the montor. For dgtal nput, mage setup s not requred. When you frst use your montor, you must perform Auto Setup for analog nput. If you are usng dgtal nput, contnue wth the nstructons on page 12. Ths procedure sets up your montor to process the vdeo sgnals from your computer wthout mage dscoloraton or smearng. After you perform Auto Setup, the settngs are stored and used each tme you turn on the montor. In order to optmze the dsplayed mage a set-up utlty s provded on the IBM Montor CD. Operaton of ths utlty s dependent on the operatng system on your computer. You may choose to run AUTO SETUP for each operatng system that you use. Ths means that f you sometmes use your montor whle runnng any verson of Wndows and sometmes also use t from wthn DOS (not a DOS wndow), you must run AUTO SETUP for both Wndows and DOS. You may run versons of AUTO SETUP n any order. Before you begn AUTO SETUP for your computer, make sure the computer vdeo mode s set n the range of the supported screen resoluton shown n the table on page 18. You should perform AUTO SETUP for each screen mode you use. 8
AutoSetup for Wndows 3.1, Wndows 95, Wndows 98, Wndows 2000, Wndows Me, Wndows XP or Wndows NT If the montor s n standby mode (STANDBY ON), t may automatcally turn off whle you are watng for t to warm up. 1. Turn on the montor frst; then the computer. If the message CHECK VIDEO CABLE s dsplayed, or f nothng s dsplayed, check: that the vdeo nterface cable s not connected properly. the correct vdeo adapter card s not nstalled. ENGLISH The sze and dversty of the dot pattern vares wth the screen resoluton. Poston the mouse ponter at the bottom center of the screen. Ths allows AUTO SETUP to run properly 2. Wat approxmately 15 mnutes, untl the montor warms up. 3. Ensure that the con bar and tool bar, f dsplayed are at the bottom of the screen. 4. Insert the CD labelled IBM Montor CD nto the CD drve. 5. Check the operatng system nstalled on your computer and follow the nstructons from the table below. Operatng System Wndows 3.1 Wndows 95 Wndows 98 Wndows 2000 Wndows Me Wndows XP Mcrosoft Wndows NT 4.0 Step1 Open PROGRAM Manager Select START Step2 Select RUN Select RUN Step3 Type E:\TESTPAT and press ENTER 6. When the test pattern appears, press the Image Setup drect access button at the bottom of the montor to run the mage setup. 7. To clear the Image Setup test pattern, press the ESC key on your keybord. You have completed the montor setup for Wndows. If you use other operatng systems, perform the approprate AUTO SETUP for those systems and also see Adjustng the mage settngs n DOS on page 10. 9
Adjustng the mage settngs n DOS If the montor s n standby mode (STANDBY ON), t may automatcally turn off whle you are watng for t to warm up. If ths happens, swtch off the montor and swtch t on agan after a few seconds. If you are usng PC-DOS/V, change to U.S. mode by typng CHEV US and pressng ENTER at the command prompt. You must use when you run DOS Auto Setup. The sze and dversty of the dot pattern vares wth the screen resoluton. If the screen flckers, repeat the setup several tmes untl the flcker s mnmsed, or adjust t manually by followng refer to Manual Setup on page 11. 1. Turn on the montor frst; then the computer. If the message CHECK VIDEO CABLE s dsplayed, or f nothng s dsplayed, check: that the vdeo nterface cable s not connected properly. the correct vdeo adapter card s not nstalled. 2. Wat approxmately 15 mnutes, untl the montor warms up. 3. Insert the CD labelled IBM Montor CD nto the CD drve. 4. Dsplay the command prompt screen of the DOS full-screen dsplay. 5. At the command prompt, type the CD drve letter, and press ENTER. 6. Type TESTPATD and press ENTER. 7. Select from the screen the number for the color or text mode you want to setup. 8. Select from the screen the number for the vdeo mode you want to setup. You may repeat ths process for as many of the color and vdeo modes as you need. 9. When the test pattern appears, press the Image Setup drect access button at the bottom of the montor to run the mage setup. 10. To clear the Image Setup test pattern, press the ESC key on your keybord. 11. Type Ext at the command prompt to return to Wndows. If you use other operatng systems, perform the approprate Image Setup for those systems and also see Image Setup Wndows 3.1, Wndows 95, Wndows 98, Wndows 2000, Wndows Me, Wndow XP or Wndows NT workstaton on page 9. 10
Manually adjustng the mage settngs ENGLISH If the montor s n standby mode (STANDBY ON), t mght automatcally turn off whle you are watng for t to warm up. Normally, you can complete the setup procedure usng Image Setup, however, f your screen mage s stll dstorted after you perform Image Setup or the setup CD does not run on your system, perform MANUAL SETUP. 1. Have your montor turned on for about 15 mnutes, untl the montor warms up. 2. Dsplay the mage you most frequently use on the screen. 3. Press the OSD Enter button at the botton of the montor to dsplay the ntal OSD menu. 4. Use an Arrow button ( or ) to select the IMAGE SET-UP con and press the OSD Enter button to access the functon. 5. Usng an Arrow button ( or ), select MANUAL, press and then press once to select COARSE. Left and rght arrow adjustment ndcators become llumnated (see page 16). 6. Use the Arrow buttons to manually adjust to correct (as much as possble) for jtter or nose n the mage, then press to save the changes. 7. Use an Arrow button to select FINE and press the button. 8. Use the Arrow buttons agan to tune the mage to your lkng. 9. When fnshed, press the Ext button four tmes to ext from the OSD. You have completed the montor setup. 11
Ergonomc Consderatons Workplace Preparaton Ths secton gves advce on what you should consder before you set up your montor. Heght Poston the montor so that the top of the screen s slghtly below your eye level when you st at your workstaton. Orentaton - Choose a poston that gves the least reflecton from lghts and wndows, usually at a rght angle to any wndows. - Poston the montor drectly n front of you so that you do not have to twst your body to use t. - Tlt the montor to a comfortable vewng angle. Workng Practces Ths secton gves advce on how you can work comfortably and reduce fatgue. Rest Take regular breaks. Vary your posture, stand up and stretch occasonally as prolonged use of computer workstatons can be trng. Back St back n your char and use the backrest. Hands Use a lght touch on the keyboard, keepng your hands and fngers relaxed. Allow a space n front of the keyboard to rest your wrsts when not typng. Consder usng a wrstpad. Eyesght Workng wth montors, n common wth any prolonged close work, can be vsually demandng. Look away from the screen perodcally and have your eyesght checked regularly. Screen settngs Set the screen brghtness and contrast to a comfortable level. You may have to adjust these settngs as the lghtng changes durng the day. Many applcaton programs let you select color combnatons whch can help you to vew n comfort. See the User controls secton on page 14 for more nformaton. 12
Adjustng the Montor Poston ENGLISH Wth the IBM Flat Panel Montor, you can adjust ts poston n varous ways for maxmum comfort. Vewng Angle You can tlt the screen forward and backward as shown below. (Fgure A) Carng for your Montor Be sure to turn off the power before you perform any mantenance on the montor. Clean your montor as follows: Gently wpe the covers and the screen wth a soft cloth. Remove fnger marks and grease wth a damp cloth and mld detergent. Never use flammable cleanng materals to clean your IBM montor or any other electrcal apparatus. 13
Adjustng Your LCD Montor User controls USER CONTROL FEATURES Icon Montor controls Swtches the montors on and off. The mage s already optmzed for many dsplay modes, however the user controls can be used to adjust the mage to your lkng. The settngs are saved after adjustment and when extng the OSD and wll be effectve thereafter. and Icon Dsplay man OSD menu and selects hghlghted menu tem. Moved the cursor to hghlght cons or make adjustments. Left and Rght arrows pressed together brng up auto setup menu. Exts from current OSD menu. Drect Access Functons Brng up Brghtness adjustment. Brng up auto mage setup. CONTROLS LOCK / UNLOCK Ths feature allows you to secure the current control settngs, whle allowng the user to adjust Brghtness or Contrast, so that they cannot be nadvertently changed. Push and hold the enter button[ ] for 10 seconds; the message Controls Locked appears. You can unlock the OSD controls at any tme by pushng the enter button[ ] for 10 seconds; the message Controls Unlocked wll appear. Swtch between nput sgnals. 14
ENGLISH On-screen dsplay (OSD) controls The LCD montor needs tme to become thermally stable the frst tme you turn t on each day. Thus, to acheve more accurate adjustments for parameters, allow the LCD montor to warm up (be On) for at least 15 mnutes before makng any screen adjustment. The settngs adjustable wth the user controls are vewed through the On - Screen Dsplay (OSD). Press the enter button [ ] to dsplay the man OSD menu. Intal appearance of OSD man menu; Analog Sgnal nput Dgtal Sgnal nput sub menu; OSD functons OSD Icon Descrpton sub-menu(s) Adjusts brghtness Control and Adjustments BRIGHTNESS Adjusts contrast CONTRAST IMAGE SET-UP The IMAGE SET-UP functon s used to adjust the level of nose n the vdeo sgnal whch causes horzontal lnes or areas on the screen where the mage appears to be unstable and jtters or shmmers. Ths can be done automatcally or manually. AUTO If AUTO s selected the mage wll automatcally adjust It s not applcable to dgtal nput. 15
OSD Icon Descrpton Sub-menu(s) Controls and Adjustments IMAGE SET-UP CONT If manual s selected, the user wll go to the manual adjustment screen. MANUAL Fne Coarse To adjust the focus of the dsplay. Ths tem allows you to remove any horzontal nose and clear or sharpen the mage of characters. Fne adjustments should be done after adjustng the Coarse. COLOR Select the COLOR MODE you fnd most comfortable or fne tune the colors usng the USER COLOR MODE menu, f necessary. COLOR MODE Preset 1 (Pnk Whte) Preset 2 (Normal Whte) Preset 3 (Blue Whte) USER COLOR MODE- Red Increases or decreases redness Green Increases or decreases greenness Blue Increases or decreases blueness Changes the poston of the OSD on the screen. H-POSITION OSD Poston V-POSITION 16
ENGLISH OSD Icon Descrpton Sub-menu(S) Controls and Adjustments RESET Reset should return all avalable functons (apart from language whch should not change unless adjusted va the LANGUAGE menu) fo ther factory presets. YES NO Moves the screen left and rght. Is not avalble wth a dgtal nput H-POSITION Moves the screen up and down. Is not avalble wth a dgtal nput V-POSITION OSD SIZE Changes the sze of the OSD menu on the screen. SMALL MEDIUM BIG Language OSD TIME The language chosen affects only the language of the OSD. Select one of the fve language to use for the OSD. It has no effect on any software runnng on the computer. To select OSD dsplay duraton tme. (5-60 seconds) ENGLISH FRANCAIS DEUTSCH ITALIANO ESPANOL Informaton Dsplay model name, seral number, year of manufacture and mcrocode level. Dsplay all preset modes stored n the montor. Dsplay all user modes stored n the montor. The current dsplay mode wll be shown at the base of all nformaton screens. INFORMATION PRESET MODES USER MODES Use the and buttons to move between nformaton screens. 17
Further Informaton Dsplay modes If your computer has prevously been used wth a CRT montor and s currently confgured to a dsplay mode outsde the range that the Flat Panel montor can dsplay, you may need to re-attach the CRT montor temporarly untl you have reconfgured the computer, preferably to 1024 x 768 at 60Hz. The dsplay mode the montor uses s controlled by the computer. Therefore, you should refer to your computer documentaton for detals on how to change dsplay modes. The mage sze, poston and shape may change when the dsplay mode changes. Ths s normal and the mage can be readjusted usng AUTO SETUP and the montor controls. Unlke CRT montors, whch requre a hgh refresh rate to mnmze flcker, TFT technology s nherently flcker-free. If possble, confgure your computer for 1024 x 768 addressablty at 60Hz vertcal refresh rate. For the dsplay modes lsted below, the screen mage has been optmzed durng manufacture. Factory Set Dsplay Modes Addressabllty Refresh Rate Horzontal Frequency 640 x 480 60 Hz 31.5 khz 640 x 480 66 Hz 35.0 khz 640 x 480 75 Hz 37.5 khz 640 x 350 70 Hz 31.5 khz 720 x 400 70 Hz 31.5 khz 800 x 600 56 Hz 35.2 khz 800 x 600 60 Hz 37.9 khz 800 x 600 72 Hz 48.1 khz 800 x 600 75 Hz 46.9 khz 832 x 624 75 Hz 49.7 khz 1024 x 768 60 Hz 48.4 khz 1024 x 768 70 Hz 56.5 khz 1024 x 768 75 Hz 60.0 khz Recommended Note : VESA tmngs are as detaled n the VESA Dsplay Montor Tmng Specfcaton. Verson 1.0, Revson 0.8, Dated 09/17/98. 18
ENGLISH Power Management To beneft from power management, the montor must be used n conjuncton wth a computer that mplements the Vdeo Electroncs Standards Assocaton (VESA) Dsplay Power Management Sgnalng (DPMS) Standard. The power management feature s nvoked when the computer recognzes that you have not used your mouse or keyboard for a user-defnable perod. There are several states as descrbed n the table below. As an ENERGY STAR 2000 Partner, IBM has determned that ths product meets the ENERGY STAR 2000 gudelnes for energy effcency. IBM recommends that you swtch off your montor at the end of each workng day, or whenever you expect to leave t unused for long perods durng the day. State Power Indcator Screen Restorng Operaton Complance On Steady green Normal Actve off Steady amber Blank Press a key or move the mouse. ENERGY STAR 2000 There may be a slght delay before the pcture reappears. 19
Troubleshootng If you have a problem settng up or usng your montor, you may be able to solve t yourself. Before callng your retaler or IBM, try the suggested actons that are approprate to your problem. Problem Possble Cause Suggested Acton Reference Screen s blank and power ndcator s off. No power to montor. Ensure that the electrcal outlet and the montor are both swtched on. Check that the power cord s frmly plugged nto the electrcal outlet and the power supply unt. If the power cord plug has a removalble fuse, replace t. Try another power cord. Try another electrcal outlet. Check the power connecton at the back of the panel. Connectng your Montor secton on page 3. Screen s blank and power ndcator s steady green. Brghtness and Contrast may be too low. Adjust brghtness and contrast. User controls secton on page 14. Screen s blank and power ndcator s steady amber. The montor s n the Power Management Standby state. Press any key on the keyboard or move the mouse to restore operaton. Check the Power Management software on your computer. Press the to swtch between analog and dgtal mode. If the panel s the wrong mode for the sgnal beng provded, the montor appears to go nto sleep mode. Power Management secton on page 19. 20
ENGLISH Problem Possble Cause Suggested Acton Reference Screen s blank and power ndcator s flashng green every 0.5 second Dsplay mode of the computer s outsde the range of the montor Reconfgure key on the computer to use a supported dsplay mode. Further Informaton secton on page 18. CHECK VIDEO CABLE message s shown and power ndcator s steady amber. The montor s not recevng a vdeo sgnal Check that the sgnal cabel s frmly connected to the computer. Check that no pns are bent n the sgnal cable connector. Connectng your montor secton on page 3. For mage problems, you may want to run AUTO SETUP agan before consultng to ths secton. In most cases, AUTO SETUP can fx the problems. See Auto Setup for the computer on page 8 for detals. Image appears to be smeared Image appears to be dscolored A few dots are mssng, dscolored, or napproprately lghted. There are noses n the vdeo sgnal The color settng may be ncorrect. Select IMAGE SET-UP menu n the OSD. Then select MANUAL to adjust FINE / COARSE settngs. Adjust the Color settngs. User Controls secton on page 14. User Controls secton on page 14. The LCD contans over 2,300,000 thn-flm transstors (TFTs). A small number of mssng, dscolored, or lghted dots may be present on the screen, whch s an ntrnsc characterstc of the TFT LCD technology and s not an LCD defect. 21
Specfcatons Ths color montor (Type-model 9512-Hxx) uses a 15-nch TFT LCD. Dmensons Wdth: Depth: Heght: 389 mm 389 mm 317.2 mm Weght 4.3 kg (9.48 lbs) Power consumpton fgures are for the montor and the power supply combned. Image Power Input Vewable Image Sze: Maxmum Heght: Maxmum Wdth: Pxel Ptch: Supply Voltage: Rated Current: 15-nch (381.0 mm) 304.1 mm 228.1 mm 0.297 mm (H) x 0.297 mm (V) 100-240 Vac 60/50 ± 3Hz 1A Power Consumpton Normal Operaton: Actve off: Off: < 35 W < 3 W < 1 W Vdeo Input Input Sgnal: Analog-75 ohm 0.7V Dgtal-DVI 1.0 Horz. Addressablty: Vert. Addressablty: Clock Frequency: 1024 pxels (max) 768 lnes (max) 108 MHz (Dgtal) 135 MHz(Analog) Sync Input Type Analog - Separate, Composte, SOG Dgtal-DVI 1.0 Communcatons VESA DDC: 2B Supported Dsplay Modes Envronment Standard modes : Horz / Vert Freq: Temperature: Operatng: Storage: Shppng: Humdty: Operatng: Storage: Shppng: IBM, VESA, MAC See Factory Set Dsplay Modes on page 18. See Dsplay Mode Ranges on page 23. 10 to 35 C - 20 to 60 C - 20 to 60 C 10 to 80% 5 to 95% 5 to 95% 22
ENGLISH Dsplay Mode Ranges Addressabllty Refresh Rate / Range ( + / - 3%) Horzontal Frequency / Range ( + / - 3%) 640 x 480 58.2 ~ 61.8 Hz 30.56 ~ 31.45 khz 640 x 480 64.0 ~ 68.0 Hz 34.95 ~ 36.05 khz 640 x 480 72.8 ~ 77.3 Hz 36.38 ~ 38.63 khz 640 x 350 67.9 ~ 72.1 Hz 30.56 ~ 31.45 khz 720 x 400 67.9 ~ 72.1 Hz 30.56 ~ 31.45 khz 800 x 600 54.3 ~ 57.7 Hz 34.14 ~ 36.26 khz 800 x 600 58.2 ~ 61.8 Hz 36.76 ~ 39.04 khz 800 x 600 69.8 ~ 74.2 Hz 46.66 ~ 49.54 khz 800 x 600 72.8 ~ 77.3 Hz 45.49 ~ 48.31 khz 832 x 624 72.8 ~ 77.3 Hz 48.21 ~ 51.19 khz 1024 x 768 58.2 ~ 61.8 Hz 46.95 ~ 49.85 khz 1024 x 768 67.9 ~ 72.1 Hz 54.81 ~ 58.20 khz 1024 x 768 72.8 ~ 77.3 Hz 58.20 ~ 61.80 khz 23