Operation Manual Model: CFR-2027 Dimmable Energy Saving Light bulb (Receiver built-in) CFR-2027 FEATURES: Pre-heat function can enhance the light bulb lifetime. Gradually lights ON in 1 second. Can be operated with either mechanical switch or wireless RF remote control. Low power consumption. Handy and easy to install.!before installation make sure to switch OFF the mechanical switch power. Switch OFF!
Initial install CFR-2027 light bulb into lamp holder then switch ON the mechanical switch, the lamp will be at the brightest level. To turn OFF, simply switch OFF the mechanical switch. REMARK!Pre-set brightness (First time switching ON) the light will be at 100% brightest. After the first dimming process is set, the next time switching ON the light will be at the last memory setting brightness/darkness. SET UP: To enter learning mode. Controlled with a RF transmitter. (Before any operation, mechanical switch must be turned ON to operate correctly) Switch ON!
1. Install CFR-2027 into lamp holder 2. Switch ON the mechanical switch. 3. Following switch mechanical switch OFF/ON 6 times ending last at ON mode, lamp starts to slow flash. This will enter learning mode. 4. On transmitter press ON button to send ON signal to CFR-2027 receiver. 5. CFR-2027 light bulbs will quick flash 8 times to confirm code is stored. 6. After the 8 times quick flash, the lamp will continuously flash slowly (returning to learning mode). 7. In the meantime, user can use another transmitter to make receiver memorize another code. CFR-2027 receiver can memorize up to 6 memories. NOTE: Operating both remote control and mechanical switch at the same time To operating with a remote control, make sure the mechanical switch is turned ON If the light is switched OFF by a remote control, remember the mechanical switch is still at ON status. So next time switching ON with the mechanical switch remember to switch twice from OFF to ON REMARK If during learning mode no RF or manual button signal is record then CFR-2027 receiver will stop flashing after 20 seconds OR either switch OFF the mechanical switch. This will deactivate the learning mode. For the convenience of setting up multiple transmitters, 20 seconds will recount again after each completed setup.
Code deleting: Single delete memory/code (Must operate from wireless RF transmitter only) 1. Switch ON the mechanical switch. 2. Following switch mechanical switch OFF/ON 6 times ending last at ON mode, lamp starts to slow flash. This will enter learning mode. 3. On transmitter press OFF button to send OFF signal to CFR-2027 receiver. 4. CFR-2027 light bulbs will quick flash 8 times to confirm single code is deleted. To deactivate learning mode, simple switch OFF the mechanical switch Delete all memories/codes: (Must operate from mechanical switch only) 1. Switch ON the mechanical switch. 2. Following switch mechanical switch OFF/ON 6 times ending last at ON mode, lamp starts to fast flash. AGAIN following switch mechanical switch OFF/ON 6 times ending last at ON mode, lamp will quick flash 8 times to confirm ALL memorized codes are deleted. 3. To deactivate learning mode, simple switch OFF the mechanical switch or wait for 20 seconds until light stops flashing. Operation of CFR-2027 with mechanical switch: Switch ON/OFF : Manual ON Button (switch ON function): Press once to switch ON. Manual OFF Button (switch OFF function): Press once to switch OFF. Dimming: 1. Switch ON the mechanical switch then quickly switch OFF then ON once again. Dimming will automatically start. 2. To stop at the desire brightness/darkness simply switch mechanical switch OFF then ON once.!dimming will automatically stop action after 4 cycles and light brightness stay at last memory level.
Operation of CFR-2027 with wireless RF remote control: Making sure mechanical switch is turned ON first! Switch ON/OFF : ON Button (switch ON function): Press once to switch ON. OFF Button (switch OFF function): Press once to switch OFF. All OFF Button (switch ALL OFF function): Press once to switch all linked lamps ALL OFF simultaneously. Dimming: 1. On transmitter press ON button to light on. 2. Press ON button again to start dimming. 3. At the desired brightness / darkness press ON button to stop dimming. SPECIFICATION: Not compatible with code switch system remote control. Power: 20W RF frequency: 433.92 MHz Input voltage: 220-240VAC Power Factor: > 0.9 Luminous: 1200 lm Current consumption: 90mA Colour: 2700 K Ra: 81 Dimming range: 5%~100% Life time: 10,000 hours. Compatible with mechanical switch and wireless RF remote control. ON / OFF /DIMMER function