AN2 Series 900tvl CMOS Technology High Resolution Sensor P/N 01.BSM.16.2000030 V1.0 Product Made in China under ISO9001 & ISO1400 standards Manual Printed in China v1.0 elinetechnology.com
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Guide Model Features: 1/3 CMOS Sensor 900TVL Sensor imaging BNC Video Output Standard 12VDC Operation lower power The lightning with an arrowhead symbol, within an equilateral triangle is intended to alert the users to the presence of un-insulated dangerous voltage within the product s enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point with an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment. To prevent electric shock and risk of fire hazards: Do NOT use power sources other than that specified. Do NOT expose this appliance to rain or moisture. Solution General Specifications This installation should be made by a qualified service person and should conform to all local codes. Operating humidity 0-90% (non-condensing) *Specifications subjected to change without prior notice. 1 2 General Power source Power Consumption Regulated 12VDC 100mA IR LED IR LED On Power 10pcs Max 275mA 15pcs Max 320mA Scanning system Progressive Scan Sensor Scanning frequency NTSC 15.734KHz( H), 59.95Hz (V) / PAL 15.625KHz (H), 50Hz (V) Effective Pixels Resolution 1305(h) x 1049(V) 900TVL OSD Control Optional Control via cable (see OSD Menu Page 7-8) ACG / BLC Noise Reduction Sync System Min. Illumination Video output S/N Ratio Video output Lens mount Lens Day/Night / ICR Programming via OSD Super flux IR LED for night vision 3D Noise reduction On 2d/ 3d Enabled Internal 0.01 Lux (AGC On, IE Off) / 0 Lux with IR LED On 1.0 Vp-p (75Ω, composite) More than 52dB (AGC ) BNC Connector 1.0Vp-p PAL / NTSC Fixed mount Matching for each model. Operating temperature -10 C ~ +50 C / -40 F ~ 122 F
Identification Mechanical Drawing 194 mm 7 5/8 in Installation Installation information (General overview) 62 mm 2 3/8 in 1 2 226 mm 8 7/8 in Locking Screw 3 4 77 mm 3 in Rotation lock Accessories 5 6 (A) Wall Plugs S7 x 26mm 3pcs (B) Fitting Screws PA4 x 24mm 3pcs (C) L-Hex tool 54x18mm (D ) Drill template NOTE: Make sure you don t have any missing parts before you make the installation. Incorrect installation could void the warranty if instructions are not followed correctly. Please call technical for assistance if you are unsure about any procedures. 1 Remove visor from camera to aid simpler installation. (Optional requirement) 2 Use drill template (D) as to guide to drill and attach camera to surface as required. Holes on bracket are 120 degree apart, so three holes are required. 3 With camera attached you can now connect power, check device working. 4 Using the (C) L-Hex tool you position left-right up/down and lock into place. The rear position rotation allows turning of angle turn anti-clockwise to loosen. 5 Adjust zoom & focus using small flat blade. (Vari-focal model only) 6 Replace the sun visor if removed from step 1. Check IR LEDs are working by covering the photocell of camera, the IR LEDs will give a faint red glow. (Don t look at IR LEDs for long periods of time, as you could damage your eyes) 3 4
Identification Mechanical Drawing Installation Installation information (General overview) 1/2 99 mm 3 7/8 in 1 2 118 mm 4 5/8 in Vari-Focal Lens Model 3 4 117.5 mm 4 5/8 in 152 mm 6 in Accessories (A) Wall Plugs S7 x 26mm 3pcs (B) Fitting Screws PA4 x 24mm 3pcs (C) L-Hex tool 58x20mm (D ) Drill template NOTE: Make sure you don t have any missing parts before you make the installation. Incorrect installation could void the warranty if instructions are not followed correctly. Please call technical for assistance if you are unsure about any procedures. 5 6 1 Use supplied template to drill holes for (A) plugs. 2 Remove locking cover using supplied (C) L-key. Optional requirement 3 Attach base part to surface with (B) screws. Use conduit if required. 4 Re-attach Cover and position camera then lock cover screws with L-Key. 5 Adjust the zoom & focus using flat blade tool. (Vari-Focal models only) 6 Connect power, feeding through conduit may require this stage to be completed before adjustment is made. Check IR LEDs are working by covering the photocell of camera, the IR LEDs will give a faint red glow. (Don t look at IR LEDs for long periods of time, as you could damage your eyes) 5 6
CAMERA ADJUSTMENT (option) The OSD control may differ from show above, OSD buttons may replace the joystick type. Service cable output maybe not be available, and maybe optionally supplied with the product. MENU TREE SUMMARY DAY&NIGHT ZONE MASK 3D-NR ON AE MODE CENTER CENTER WEIGHT BACK LIGHT FRONT LIGHT WB AWB-TEMPORAL AWB-AI AWB-SZ AWB-GW AWB-CCT AWB-PEO ENHANCE SHARPNESS DETAIL EDGE CONTRAST AUTO MANUAL SATURATION AUTO MANUAL 0-15 MIRROR FLIP BRIGHTNESS ZOOM IN AUTO EXT BLACK&WHITE COLOR COLOR AREA NO.0 - AERA NO.7 ZONE MASKING COLOR AREA NO.0 - AERA NO.7 STATUS HORIZON SIZE VERTICAL SIZE HORIZON MOVE VERTICAL MOVE MOTION DETECTION SENSITIVITY AREA NO.0 - AERA NO.3 ZONE MASKING STATUS COLOR HORIZON SIZE VERTICAL SIZE HORIZON MOVE VERTICAL MOVE VIDEO STANDARD PAL NTSC ENGLISH CHINESE SAVE& CAMERA ADJUSTMENT (option) Highlight boxes below shows the menu path. Value ranges given in menu below are a guide for setting ranges, the camera osd will show only single values. DAY&NIGHT AUTO ZONE MASK MOTION DETECTION VIDEO STANDARD PAL ENGLISH SAVE& DAY&NIGHT AUTO ZONE MASK MOTION DETECTION VIDEO STANDARD PAL ENGLISH SAVE& ZONE MASKING COLOR AREA NO.0 AREA NO.1 AREA NO.2 AREA NO.3 AREA NO.4 AREA NO.5 AREA NO.6 AREA NO.7 ZONE MASKING MAGENTA STATUS HORIZON SIZE 0~1280 VERTICAL SIZE 0~720 HORIZON MOVE 0~1280 VERTICAL MOVE 0~720 3D-NR ON AE MODE GLOBAL WB AWB-TEMPORAL ENHANCE MIRROR FLIP BRIGHTNESS 0~250 ZOOM IN 0~5 DAY&NIGHT AUTO ZONE MASK MOTION DETECTION VIDEO STANDARD PAL ENGLISH SAVE& MOTION DETECTION SENSITIVITY AREA NO.0 AREA NO.1 AREA NO.2 AREA NO.3 MOTION DETECTION HIGH STATUS COLOR WHITE HORIZON SIZE 0~1280 VERTICAL SIZE 0~720 HORIZON MOVE 0~1280 VERTICAL MOVE 0~720 ENHANCE SHARPNESS CONTRAST SATURATION SHARPNESS DETAIL MANUAL VALUE 0~15 EDGE MANUAL VALUE 0~15 CONTRAST CONTRAST MANUAL VALUE 0~255 SATURATION SATURATION MANUAL VALUE 0~15 7 8
TROUBLE SHOOTING Follow the steps below if you are experiencing trouble with your camera, before you contact your Technical Support. NOTES Nothing appears on the screen. Check that the power cable is connected properly and that the voltage is correct. Check that you have properly connected VIDEO cable to the camera VIDEO output jack and to the monitor/dvr. The image on the screen is unclear. Is the lens or dome cover stained with dirt? Clean lens or dome cover with soft, clean cloth. Re-position the camera if necessary. Adjust the Zoom and Focus screws as needed. The image on the screen is dark. If you have an intermediate device, set the impedance to 75Ω / Hi-z. Adjust the monitor contrast & brightness controls. Image quality is poor. Be sure to check cable for and braid which may be touching the common Coaxial core pin. Verify that the camera is receiving sufficient power. There is interference in the image. The camera or the cables may be close to a source of high voltage, such as a generator. Re-position the camera if necessary. When the resistance value of copper wire is at [20 C(68 F)] Copper wire size (AWG) #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) #18(0.83mm2) Resistance (Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adapter output line for connection to the camera may affect the performance of the camera. *Standard voltage for camera operation : DC12V ±10% or *There may be some deviation in voltage drop depending on the type of wire and the manufacturer. Be sure to connect power only after all the installation is complete. Use the UL listed, CLASS 2 power transformer for 12v DC adapter. 9 10