Liko Service System - LSS. Prod. No Product Description

7.0 Liko Service System - LSS Prod. No. 21090024 Product Description Liko Service System is a soft ware developed to enable service technicians to conduct service in an easy way on all lifts equipped with the control unit CBL 20. It also gives the service technician the possibility to program the spare part on the field. Detailed information can be found in the instruction guide supplied with the product. Service Liko Service Manual System Viking L mobile lift 3EN360401 Rev. 10 74 www.hill-rom.com l www.liko.com

8.0 Liko Diagnostic System - Service LDS Service Prod. No. 21090016 L Product Description Liko mobile lifts equipped with LDS (Liko Diagnostic System ), record and store information on how the lift is used. LDS Service can read the information stored in the Control unit CBL. LDS Service can be used as hand control to operate Liko IR controlled mobile lifts. LDS Service is specially developed for Hill-Rom authorized service technicians to reset the Control Unit CBL service interval after completed service/periodic inspection. Detailed information can be found in the instruction guide supplied with the product. Service Manual Viking L mobile lift 3EN360401 Rev. 10 75 www.hill-rom.com l www.liko.com

Service Manual Viking L mobile lift 3EN360401 Rev. 10 76 www.hill-rom.com l www.liko.com

Periodic Inspection Viking mobile lift Viking XL Viking L Viking M Prod. No. 2040003 2040004 2040005 2040013 2040014 2040015 2040033 2040034 2040035 Output (TAAxT):... Ah (Prod. No. 2040013-2040035) (Use Liko Service System or Liko Diagnostic System to read data from the CBL) Lift type:... Prod No:... Serial No:... Prod. Year:... 9.0 Customer Reference: Contract No:... Name:... Address:... (Zip Code)... The lift must be thoroughly inspected when the Service Light at the Control Unit CBL iiluminates, or at least once per year. Viking with control unit other than CBL shall be thoroughly inspected at least once per year. Inspection and service must be carried out by Hill-Rom authorized personnel. INSPECTION POINTS Approved Not To be actioned: approved 1 Product decal... 2 Visible damage to the lift surface finish... 3 Castor wheels, forks and fork covers... 4 Castor brakes... 5 Base covers... 6 Base opening and closing linkage... 7 Base frame castor play and levelling... 8 Locking handles... 9 Lift arm hardware and covers... 10 Flexlink to arm hardware and covers... 11 Flexlink to slingbar hardware and covers... 12 Slingbar... 13 Mast actuator... 14 Battery and electrical cable installations... 15 Hand control... 16 Emergency stop function... 17 Emergency lowering device... 18 Control unit CBL20... LOAD TESTING 19 Max. load test... 20 Mechanical em. lowering load test... ACCESSORY 21 Armrest DOCUMENTATION 22 Instruction guide... CLEAR SERVICE (CBL20) 23 Service symbol reset by using: LSS LDS Manual service Approval to use the overhead lift: Approved Not approved To be actioned If the overhead lift has one or more inspection point with result Not approved the system must not be used. If the system has one or more inspection point with result To be actioned these actions should be performed immediatley. After performed actions sign below. If anything is unclear or if you have questions, please contact Hill-Rom or your local Hill-Rom representative. Contact information is to be found at www.liko.com l www.hill-rom.com Inspection performed by: Date: Final approval by: Approval date: Next inspection: Inspection performed in accordance with ISO 10535:2006 Annex B- Periodic inspection Service Manual Viking L mobile lift 3EN360401 Rev. 10 77 www.hill-rom.com l www.liko.com

9.0 Check points Viking XL mobile lift Prod. No. 2040003 Viking L mobile lift Prod. No. 2040004 Viking M mobile lift Prod. No. 2040005 Viking XL mobile lift 12 11 10 9 12 21 13 20 15 14 16 17 8 1 6 4 3 5 7 Check points Viking XL mobile lift Prod. No. 2040013, 2040033 Viking L mobile lift Prod. No. 2040014, 2040034 Viking M mobile lift Prod. No. 2040015, 2040035 Viking L & Viking XL mobile lift 15 9 10 Viking XL 13 11 12 20 12 13 20 18 16 1 21 14 6 8 7 4 5 3 Service Manual Viking L mobile lift 3EN360401 Rev. 10 78 www.hill-rom.com l www.liko.com

Instructions for the check points 9.0 1 Product decal - Verify presence of mast decal with model type and serial number. 2 Visible damage to the lift surface finish - Check for scratches, dents, deformities or unusual surface wear. 3 Castor wheels, forks and fork covers - Roll the lift, unloaded and with load, along the floor. Check to ensure that all castors roll and turn freely. - Verify that the castor fasteners are tight. There should not be any play between the fork and the castor nut. - Remove the front fork cover and inspect safety casing and bolt channel for cracks or fractures. 4 Castor brakes - Lock the brakes. Make sure the wheels do not turn and the castor housing does not swivel when the lift is pushed. 5 Base covers - Verify that the protective plastic covers are secure. 6 Base opening and closing linkage - Inspect the linkage between legs and base motor. Make sure there is no cracks or deformations at the legs. - Inspect the plastic protective cover shell for cracks, deformation or gaps. - Open and close the base to maximum and minimum dimensions. - Listen for particular noises and vibrations. 7 Base frame castor play and levelling - Manually open and close legs at the front castors to measure wheel play. Base width wheel play should not exceed 35mm / 1,38 Inch total. 8 Locking handles - Loosen & re tighten locking handles. Verify that threads are not damaged or binding. 9 Lift arm hardware and covers - With the liftarm in it s lowest position, carefully maually raise the lift arm. NOTE! Do not lift higher than shoulder hight. Verify that the shaft lowers and raises freely. If the arm is binding, the mounting screw is to tight. - Inspect the plastic protective cover shells for cracks, deformation or gaps. - Make sure the holes in the mast are not deformed on: Product Product No. Up to S/N: Viking XL mobile lift 2040003 801 999 Viking L mobile lift 2040004 7 200 795 Viking M mobile lift 2040005 7 106 200 Verify that the diameter of the holes in the mast (where the arm and mast is connected) are not bigger than 12 mm/0,47 inch. It can be done by measuring the distance from cover hat, to top of the ear. The length should be the same on each side (X¹=X²)±1 mm. X¹ X² 10 Flexlink to arm hardware and covers - With the slingbar hanging in it s lowest position, manually raise the slingbar and flexlink arm. - Verify that the flexlink arm lowers and raises freely. If the flexlink is binding the screw is too tight. - Inspect the plastic protective cover shells for cracks, deformation or gaps. 11 Flexlink to slingbar hardware and covers - With the slingbar hanging in it s lowest position, manually pivot the slingbar side-to-side. Verify that the flexlink arm lowers and raises freely. If the flexlink is binding, the mounting screw is too tight. - Verify that hardware covering plastic caps are secure. - If no accessories is attached, verify that the slingbar is assembled directly to the flexlink. Service Manual Viking L mobile lift 3EN360401 Rev. 10 79 www.hill-rom.com l www.liko.com

Instructions for the check points 9.0 12 Slingbar - Inspect visually to ensure that the slingbar is free from any scratches, sharp edges or deformities. - Check that the unit rotates freely on its bearings. - Make sure that both latches are mounted and fall back against the body of the slingbar. 13 Mast actuator - Verify that the upper and lower actuator fasteners to the mast are tight. - Visual inspection of tubes, back fixture and piston rod eye. - Check of abnormal noise. - If the lift is equipped with Outer tube: Pull the Outer Tube to the top and bottom (with the lift arm in its highest position). Make sure the Outer Tube not get stuck in any position. - Check of electric end stop Prod. No. 2040003-2040005: By using test box 21090014 UK or 21090015 US Prod. No. 2040013-2040015 and 2040033-2040035: Run the lift all the way up and down. Verify that the Indicator lamp for overload (orange light) not lights. 14 Battery and electrical cable installations - Verify that all cables are properly inserted. Re-insert if uncertain. - Make sure the charge cable hook is mounted at the mast. Prod. No. 2040003-2040005: Verify battery charge (recharge battery or test with Prod. No. 2101100 Battery tester with diodes). Prod. No. 2040013-2040015 and 2040033-2040035: Inspect that the cable cover is mounted correctly. Verify battery charge. During charging the lights shall shine alternatively (orange, orange, green). Completed charging is indicated by a flashing green light. 15 Hand control - With the emergency stop out, verify that all functions on the hand control are working. Prod. No. 2040013-2040015 and 2040033-2040035: With the emergency stop out, verify that all functions on the operation panel are working. 16 Emergency Stop function - Press the emergency stop button. With the emergency stop pressed in, verify the lift does not operate with the hand control buttons. - Turn the red emergency button in the direction of the arrows. Verify the button releases from the locked position into the raised, open position. 17 Emergency lowering device (only on Prod. No. 2040003-2040005) - With the emergency stop out, verify that the electrical emergency-lowering device functions. 18 Control unit CBL 20 ( Prod. No. 2040013-2040015 and and 2040033-2040035) - With the emergency stop out, verify the function of the electrical emergency-lowering device at the operation panel. 19 Max. load test - Run the lift with maximum load, all the way up and down. - Run the base in and out with maximum load. - Make sure all four wheels have contact with the floor. - Listen for peculiar noises and vibrations. Max load kg lbs Viking M 205 450 Viking L 250 550 Viking XL 300 660 Service Manual Viking L mobile lift 3EN360401 Rev. 10 80 www.hill-rom.com l www.liko.com

Instructions for the check points 9.0 20 Mechanical emergency lowering load test - Raise with maximum load (see table above) and with (50 kg/110 lbs) until the arm is parallel to the ground. Prod. No. 2040003-2040005, 2040015, 2040035: Lift red emergency handle on the actuator upwards and hold, verify that the load lowers. Prod. No. 2040013, 2040014, 2040033, 2040034: Manually turn the red actuator collar in the direction of the arrows to lower. 21 Armrest (accessory) - Verify that both arms rotate freely and hang vertically when not in use. - Rotate arms to raised position. Perform a load test of the armrest with (40 kg/88 lbs). 22 Documentation - Verify that the Instruction guide is provided. 23 Clear Service (CBL 20) - Only products with Control Unit CBL20 (Prod No 2040013-2040015 and 2040033-2040035) Service indicator (orange light) - Illuminates when service is needed. When the Periodic Inspection has been performed, reset the service indicator with LSS, LDS or Manual Service according to instructions Reset Service Interval Parameters in the Service Manual. Service Manual Viking L mobile lift 3EN360401 Rev. 10 81 www.hill-rom.com l www.liko.com

Service Manual Viking L mobile lift 3EN360401 Rev. 10 82 www.hill-rom.com l www.liko.com

Preventive Maintenance Viking mobile lift Viking XL Viking L Viking M Prod. No. 2040003 2040004 2040005 2040013* 2040014* 2040015* 2040033* 2040034* 2040035* * Lift equipped with Control Unit CBL 10.0 Lift type:... Product No:... Serial No:... Prod. Year:... If Liko Service System (LSS) or Liko Diagnostic System (LDS) are available, data can be read from lifts equipped with Control Unit CBL. With LSS you can store data and with LDS, write down the values in the columns below. Customer references Agreement No:... Name:... Address:... Post code:... TAAxT Ah AABT Removals PAAxT Ah AEUP EposUp AAS Starts AFSERV Services ASERV Times AEDWN EposDn IMED ma IDNR ALA Charges AOLUP OverLoads AALA Charges PADT Hours AOLA Charges PAOLUP OverLoads To ensure maximum life cycle, Preventative Maintenance should be carried out according to how much the lift has been used TAAxT (Totally Accumulated Amphours) or according to years in use, see table below. TAAxT can only be read from lifts equipped with Control Unit CBL. Inspection and service must be carried out by Hill-Rom authorized personnel. Check points: Maintenance according to used TAAxT (Ah): Viking XL mobile lift (with Control Unit CBL) 102 204 306 408 510 612 714 816 918 Viking L mobile lift (with Control Unit CBL) 91 182 279 364 455 546 637 728 819 Viking M mobile lift (with Control Unit CBL) 70 140 210 280 350 420 490 560 630 Maintenance according to years of use: 1 2 3 4 5 6 7 8 9 1 Surface treatment... 2 Front castors... 3 Rear castors / brakes... 4 Pivot bolts... 5 Base opening and closing linkage... 6 Base motor linkage... 7 Lift arm... 8 Flexlink / Lift arm joint / Slingbar bolt... 9 Battery.... 10 Actuator... Lubricate with PTFE or silicon grease When maintenance is performed; mark specified square with X When part is replaced; mark specified square with R Interval/Month: Date: Serviced by: 2015-04 Service Manual Viking L mobile lift 3EN360401 Rev. 10 83 www.hill-rom.com l www.liko.com

Check points 10 7 10.0 8 11 9 6 3 4 5 1 Surface treatment Visually inspect the lift for external damage or wear. If needed, clean the patient lift with warm water or ethanol. Warning! Do not use chemicals containing phenol or chlorine, since the aluminium parts may be damaged. 2 Instructions regarding the check points Viking L & Viking XL 2 Front castors Check and clean front castors. If wheels are in poor condition, replace them. (For Spare Part No, see the Spare Parts List) 3 Rear castors / brakes Viking M Viking L & XL Check and clean rear castors. If wheels are in poor condition, replace them. (For Spare Part No, see the Spare Parts List) Check the brakes. They should lock in all directions. Service Manual Viking L mobile lift 3EN360401 Rev. 10 84 www.hill-rom.com l www.liko.com

4 Pivot bolts Instructions regarding the check points 10.0 x2 Flat side down Inspect plastic cover, clean them if necessary. Lubricate inner side with flourflon PTFE grease. Remove pivot bolt, inner and outer bearing sleeves and hardware. Clean and lubricate pivot bolt, inner and outer bearing sleeves. 5 Base opening and closing linkage Remove hardware covers from middle beam and actuator. Remove leg from middle beam and actuator. (a) Remove pivot bolt, inner and outer bearing sleeves and hardware. (b) Remove link arm cover, bolt and nut. Remove plastic covers and inspect middle beam edges for burrs. File smooth if required. Clean and inspect the three pieces of plastic cover. Replace if cracked or deformed. (For Spare Part No see the Spare Parts List) Clean, lubricate and reassemble pivot bolt, bearing sleeves and hardware. Tighten pivot bolt and apply plastic hardware covers. Reconnect actuator to link arm. Apply plastic hardware covers. Viking XL Viking L Viking M Leg covers needs to be replaced after: 612 Ah 546 Ah 420 Ah or Replace according to years in use: 6 6 6 Service Manual Viking L mobile lift 3EN360401 Rev. 10 85 www.hill-rom.com l www.liko.com

6 Base motor linkage Instructions regarding the check points 10.0 Remove link arm cover, bolt and nut. Clean, lubricate and reassemble pivot bolt, bearing sleeves and hardware. Inspect the legs at the linkage. If the linkage are in poor condition, replace them with Restoration set motor attachment. (For Spare Part No, see the Spare Parts List) Reconnect actuator to link arm. Apply plastic hardware covers. x2 Restoration set motor attachment 7 Lift arm Remove hardware covers. Remove and lubricate lift arm bolt. Visually inspect lift arm, plastic covers for wear, cracks or deformation. Reassemble in reverse order. Carefully manually raise the lift arm. NOTE! Do not lift higher than shoulder hight. Then release, so that it falls to the lowest position. If the arm does not fall to the lowest position, the screw is too tight. x2 x3 x6 Remove and lubricate actuator hardware. Visually inspect actuator plastic bushings for wear. Replace if worn. Reassemble in reverse order. x6 x2 Overhead beam Restoration set (For Spare Part No, see the Service Manual.) Service Manual Viking L mobile lift 3EN360401 Rev. 10 86 www.hill-rom.com l www.liko.com

8 Flexlink / Lift arm joint / Slingbar bolt Instructions regarding the check points 10.0 Inspect Flexlink: 1. Remove covers. 2. Remove, clean and lubricate flexlink. Inspect shell covers for cracks or gaps. 3. Pull out the Flexlink and check for wear. Re-assemble in reverse order. 4. Lift up the slingbar and then release, so that it falls to the lowest position. If the link does not fall to the lowest position, the screw is too tight. Inspect Slingbar bolt: (Universal SlingBar and Universal TwinBar) 1. Check slingbar bolt for wear. 2. Remove slingbar centerbolt and bearing, wipe of any dirty, dust or residue. (Universal Twinbar) 3. Reassemble in reverse order pivot slingbar centerbolt within the Flexlink. If the slingbar is binding, the screw is too tight. X Exposed to wear Max wear: M = X -3mm Pull out the Flexlink and check for wear by measuring with the sliding caliper. Replace link with Spare Part No. 20490049, if its worn more than 3mm (0,12 inch) Reassemble in reverse order. Service Manual Viking L mobile lift 3EN360401 Rev. 10 87 www.hill-rom.com l www.liko.com

9 a) Battery to Control UnitCBL Instructions regarding the check points 10.0 2 3 4 1 Battery capacity Check battery capacity by pressing the i button (1). The following information is displayed: 2 Green light: More than 50% of battery capacity remaining. 3 Yellow light: 25% -50% of battery capacity remaining. 4 Yellow light: 0% -25% of battery capacity remaining. The indicator lamps light for about 30 seconds before switching off. Battery capacity is also displayed during lift operation. Maximum charge is reached after about 5 hours. When the batteries are fully charged, the charger switches automatically to maintenance charging. The lamps blink alternately (yellow/yellow/green) during charging. A blinking green lamp indicates that charging is complete. When operating time is noticeably shorter than normal, the batteries should probably be replaced. Discontinue charging and replace the batteries with 2006107 Extra battery box. Prod. No. 2006107 Extra battery box Viking XL Viking L Viking M Batteries needs to be replaced after: 408 Ah 364 Ah 280 Ah and: 816 Ah 728 Ah 560 Ah or Replace according to years in use: 4 and 8 4 and 8 4 and 8 9 b) Battery to Jumbo Control Box 1. 2. 1. Remove the charger cable holder. 2. Remove the battery. 3. Inspect V-shaped metal contacts on the batterypack casing for uniformity. Check the battery with the battery tester Part. No. 2101100. A signal should be audible for more than 5 sec. If not, replace battery with spare part 2006106. 4. Inspect V-shaped metal contacts on control box for uniformity. Verify that plastic housing for metal contacts is not damaged/deformed. Tighten screws. 5. Place the removable battery pack into position on top of the control box. Adjust until you hear a clicking sound. 3. 4. 5. Replace according to years in use: Every 3rd year 10 Actuator 1. Visually inspect the actuator and the Outer tube (Outer Tube only on Viking M) for wear, cracks or deformation. Service Manual Viking L mobile lift 3EN360401 Rev. 10 88 www.hill-rom.com l www.liko.com

11.0 Viking L Product changes Prod. No. 2040004, 2040014, 2040034 2013-05-24 Prod. No. 2040034 S/N 9 300 001-9 400 000 Prod. No. 2040014 S/N. 7 800 001-7 900 000 Prod. No. 2040004 S/N. 7 200 201-7 300 300 (Discontinued 2013) Changes 2013 Model 2040034 S/N Model 2040014 S/N Model 2040004 S/N Project Viking L, Prod No. 2040004 is discontinued. - - - 1740 2012 New model Prod. No. 2040034 with intelligent control unit and fixed hand control. 9 300 001 1707 2010 New model Prod. No. 2040014 with intelligent control unit and IR hand control. 7 800 001-934 2008 4 mm shorter middle beam. Link attachment for base motor adjusted. 7 202 000 671 2007 Outer tube on actuator, and washers in pivot points. 7 201 500 520 New arm and friction washers at link Viking L introduces. 7 200 795 EFR715 Old safety latch back. 7 200 690 619 New safety latch composite. 7 200 664-2006 Flourflon grease inside of outer leg casing. 7 200 637 - Hook composite with safety latch composite. 7 200 591 467 Actuator Viking XL replaces actuator Viking L. 7 200 586 - Keeps the actuator, Viking XL has different actuator. 7 200 511 432 901890122 Screw M6S M10x40 GL=15 mm change to 930000040 screw M6S M10x40. 7 200 488 - New pivot points between arm-mast, actuator-arm, Mast-actuator, arm- link and link-slingbar. 7 200 488 - New arm. Same as Viking XL, different hole. 7 200 483 - Service Manual Viking L mobile lift 3EN360401 Rev. 10 89 www.hill-rom.com l www.liko.com

11.0 Viking L Product changes Prod. No. 2040004, 2040014, 2040034 2013-05-24 Changes Model 2040004 S/N 2005 New screw thread on bolts M6S M10x80 och M6S M10x65. 7 200 483 New length on mast. 7 200 483 New diagonal profile inside the Middle Beam. 7 200 476 New locking handles. 7 200 431 Emergency guard for control box. 7 200 431 2004 New Slingbar Universal Slingbar 450. 7 200 387 Viking L delivered with the old Slingbar Standard 450. 7 200 285 Service Manual Viking L mobile lift 3EN360401 Rev. 10 90 www.hill-rom.com l www.liko.com

Service Manual Viking L mobile lift 3EN360401 Rev. 10 91 www.hill-rom.com l www.liko.com

Copyright Liko R&D AB 2015 www.hill-rom.com I www.liko.com Liko AB Nedre vägen 100 SE-975 92 Luleå, Sweden