HLMP-AG64/6, HLMP-AM64/6, HLMP-AB64/6 Precision Optical Performance and New mm Mini Oval LEDs Data Sheet Description These Precision Optical Performance Oval LEDs are specifically designed for full color/video and passenger information signs. The oval shaped radiation pattern and high luminous intensity ensure that these devices are excellent for wide field of view outdoor applications where a wide viewing angle and readability in sunlight are essential. The package epoxy contains both UV-A and UV-B inhibitors to reduce the effects of long term exposure to direct sunlight. Package Dimensions Package drawing A 8.7 ±.2.342 ±.8 24..94 MIN. Features Well defined spatial radiation pattern High brightness material Available in red, green and blue color AlInGaP 626 nm InGaN 2nm InGaN 47nm Superior resistance to moisture Standoff Package Tinted and diffused Typical viewing angle 3 x 7 Applications Full color signs CATHODE LEAD 1..38 MIN. Measured at base of lens 3.8 ±.2.1 ±.8.2 ±.2.2 ±.8 2.4 ±.3.1 ±.12 Package drawing B.8.16 MAX. EPOXY MENISCUS. ±.1.2 ±.4 Sq Typ 11.7 ±..466 ±.2 8.7 ±.2.342 ±.8 1. ±.1.91 ±.6 24..94 MIN. CATHODE LEAD 1. MIN..38 Measure at base of lens 3.8 ±.2.1 ±.8.2 ±.2.2 ±.8 2.4 ±.3.1 ±.12 Notes: All dimensions in millimeters (inches). Tolerance is ±.2mm unless other specified.8 MAX. EPOXY MENISCUS.32. ±.1.2 ±.4 Sq Typ Caution: INGaN devices are Class 1C HBM ESD sensitive per JEDEC Standard. Please observe appropriate precautions during handling and processing. Refer to Application Note AN 1142 for additional details.
Device Selection Guide Part Number Color and Dominant Wavelength ld (nm) Typ Luminous Intensity Iv (mcd) at 2 ma-min Luminous Intensity Iv (mcd) at 2 ma-max Standoff HLMP-AG64-X1xx 626 166 3 No A HLMP-AG6-X1xx 626 166 3 Yes B HLMP-AM64-14xx 2 29 6 No A HLMP-AM6-14xx 2 29 6 Yes B HLMP-AB64-TWxx 47 8 166 No A HLMP-AB6-TWxx 47 8 166 Yes B Tolerance for each intensity limit is ± 1%. Notes: 1. The luminous intensity is measured on the mechanical axis of the lamp package. Package Drawing Part Numbering System H L M P - A x 6 x x x x x x Packaging Option DD: Ammopack ZZ: Flexi Ammopack Color Bin Selection : Open distribution Maximum Intensity Bin : No maximum intensity limit Minimum Intensity Bin Refer to Device Selection Guide. Standoff/ Non Standoff 4: Non Standoff : Standoff Color G: 626 M: 2 B: 47 Package A: mm Mini Oval 3 x 7 Note: Please refer to AB 337 for complete information about part numbering system. 2
Absolute Maximum Ratings T A = 2 C Parameter and Unit DC Forward Current [1] 3 ma Peak Forward Current 1 [2] 1 [3] ma Power Dissipation 12 116 mw Reverse Voltage (I R = 1 μa) (I R = 1 μa) V LED Junction Temperature 13 11 C Operating Temperature Range -4 to +1-4 to +8 C Storage Temperature Range -4 to +1-4 to +1 C Notes: 1. Derate linearly as shown in Figure 4 and Figure 8 2. Duty Factor 3%, frequency 1KHz. 3. Duty Factor 1%, frequency 1KHz. Electrical / Optical Characteristics T A = 2 C Parameter Symbol Min. Typ. Max. Units Test Conditions Forward Voltage Reverse Voltage & blue Dominant Wavelength [1] Peak Wavelength V F 1.8 2.8 2.8 V R l d 618 2 46 2.1 3.2 3.2 626 2 47 l PEAK 634 16 464 2.4 3.8 3.8 63 4 48 V V nm nm I F = 2 ma I F = 1 μa I F = 1 μa I F = 2 ma Peak of Wavelength of Spectral Distribution at I F = 2 ma Thermal Resistance Rq J-PIN 24 C/W LED Junction-to-Pin Luminous Efficacy [2] h V 1 3 6 lm/w Emitted Luminous Power/ Emitted Radiant Power Notes: 1. The dominant wavelength is derived from the chromaticity Diagram and represents the color of the lamp 2. The radiant intensity, Ie in watts per steradian, may be found from the equation Ie = I V /h V where I V is the luminous intensity in candelas and h V is the luminous efficacy in lumens/watt. 3
AlInGaP RELATIVE INTENSITY 1.8.6.4.2 6 6 7 WAVELENGTH - nm Figure 1. Relative Intensity vs Wavelength FORWARD CURRENT - ma 4 3 2 1. 1 1. 2 2. FORWARD VOLTAGE - V Figure 2. Forward Current vs Forward Voltage RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 2 ma) 2. 2 1. 1. 1 2 3 4 DC FORWARD CURRENT - ma IF MAX. - MAXIMUM FORWARD CURRENT - ma 6 4 3 2 1 2 4 6 8 1 T A - AMBIENT TEMPERATURE - -C Figure 3. Relative Intensity vs Forward Current Figure 4. Maximum Forward Current vs Ambient Temperature 4
InGaN and 1. 3.9.8 2 RELATIVE INTENSITY.7.6..4.3.2.1 BLUE GREEN. 38 43 48 3 8 63 WAVELENGTH - nm FORWARD CURRENT - ma 2 1 1 1 2 3 4 FORWARD VOLTAGE -V Figure. Relative Intensity vs Wavelength Figure 6. Forward Current vs Forward Voltage RELATIVE LUMINOUS INTENSITY (NORMALIZE AT 2 ma) 1.6 1.4 1.2 1 GREEN.8.6.4 BLUE.2 1 1 2 2 3 3 DC FORWARD CURRENT - ma I F max - MAXIMUM FORWARD CURRENT - ma 3 3 2 2 1 1 2 4 6 8 1 T A - AMBIENTTEMPERATURE - C Figure 7. Relative Intensity vs Forward Current Figure 8. Maximum Forward Current vs Ambient Temperature DOMINANT WAVELENGHT SHIFT - nm 16 14 12 1 8 GREEN 6 4 2 BLUE -2-4 1 1 2 2 3 3 FORWARD CURRENT - ma Figure 9. Relative dominant wavelength vs Forward Current
NORMALIZED INTENSITY 1..9.8.7.6..4.3.2.1. Figure 1. Radiation Pattern-Major Axis -9-6 -3 3 6 9 ANGULAR DISPLACEMENT-DEGREE NORMALIZED INTENSITY 1..9.8.7.6..4.3.2.1. -9-6 -3 3 6 9 ANGULAR DISPLACEMENT - DEGREE Figure 11. Radiation Pattern-Minor Axis 6
Intensity Bin Limit Table (1.2: 1 Iv Bin Ratio) Bin Intensity (mcd) at 2 ma Min Max T 8 96 U 96 11 V 11 138 W 138 166 X 166 199 Y 199 24 Z 24 29 1 29 3 2 3 42 3 42 4 4 4 6 Tolerance for each bin limit is ± 1% VF Bin Table (V at 2mA) Bin ID Min Max VD 1.8 2. VA 2. 2.2 VB 2.2 2.4 Notes: 1. Tolerance for each bin limit is ±.V 2. VF binning only applicable to color. Color Range Min Dom Max Dom Xmin Ymin Xmax Ymax 618 63.6872.3126.689.2943 Tolerance for each bin limit is ±.nm.669.3149.78.292 Color Bin Table Bin Min Dom Max Dom Xmin Ymin Xmax Ymax 1 2. 24..743.8338.186.66.16.686.16.8292 2 24. 28..16.8292.268.6463.186.66.1387.8148 3 28. 32..1387.8148.2273.6344.268.6463.172.796 4 32. 36..172.796.2469.6213.2273.6344.23.7764 36. 4..23.7764.269.67 Tolerance for each bin limit is ±.nm. Color Bin Table Bin Min Dom.2469.6213.2296.743 Max Dom Xmin Ymin Xmax Ymax 1 46. 464..144.297.1766.966.1818.94.1374.374 2 464. 468..1374.374.1699.162.1766.966.1291.49 3 468. 472..1291.49.1616.129.1699.162.1187.671 4 472. 476..1187.671.117.1423.1616.129.163.94 476. 48..163.94.1397.1728 Tolerance for each bin limit is ±.nm.117.1423.913.1327 Note: 1. All bin categories are established for classification of products. Products may not be available in all bin categories. Please contact your Avago representative for further information. 7
Relative Light Output vs Junction Temperature 1 RELATIVE LIGHT OUTPUT (NORMALIZED AT TJ = 2 C) 1.1-4 -2 2 4 6 8 1 12 14 T J - JUNCTION TEMPERATURE - C Avago Color Bin on CIE 1931 Chromaticity Diagram 1..8 1 2 3 4.6 Y.4.2 4 3 2 1...1.2.3.4..6.7.8 X 8
Precautions: Lead Forming: The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering on PC board. For better control, it is recommended to use proper tool to precisely form and cut the leads to applicable length rather than doing it manually. If manual lead cutting is necessary, cut the leads after the soldering process. The solder connection forms a mechanical ground which prevents mechanical stress due to lead cutting from traveling into LED package. This is highly recommended for hand solder operation, as the excess lead length also acts as small heat sink. Soldering and Handling: Care must be taken during PCB assembly and soldering process to prevent damage to the LED component. LED component may be effectively hand soldered to PCB. However, it is only recommended under unavoidable circumstances such as rework. The closest manual soldering distance of the soldering heat source (soldering iron s tip) to the body is 1.9mm. Soldering the LED using soldering iron tip closer than 1.9mm might damage the LED. 1.9mm ESD precaution must be properly applied on the soldering station and personnel to prevent ESD damage to the LED component that is ESD sensitive. Do refer to Avago application note AN 1142 for details. The soldering iron used should have grounded tip to ensure electrostatic charge is properly grounded. Recommended soldering condition: Wave Manual Soldering [1, 2] Pre-heat temperature 1 C Max. - Preheat time 6 sec Max - Solder Dipping Peak temperature 2 C Max. 26 C Max. Dwell time 3 sec Max. sec Max Note: 1) Above conditions refers to measurement with thermocouple mounted at the bottom of PCB. 2) It is recommended to use only bottom preheaters in order to reduce thermal stress experienced by LED. Wave soldering parameters must be set and maintained according to the recommended temperature and dwell time. Customer is advised to perform daily check on the soldering profile to ensure that it is always conforming to recommended soldering conditions. Note: 1. PCB with different size and design (component density) will have different heat mass (heat capacity). This might cause a change in temperature experienced by the board if same wave soldering setting is used. So, it is recommended to re-calibrate the soldering profile again before loading a new type of PCB. 2. Avago Technologies AllnGaP high brightness LED are using high efficiency LED die with single wire bond as shown below. Customer is advised to take extra precaution during wave soldering to ensure that the maximum wave temperature does not exceed 2 C and the solder contact time does not exceeding 3sec. Over-stressing the LED during soldering process might cause premature failure to the LED due to delamination. Avago Technologies LED configuration CATHODE InGaN Device Note: Electrical connection between bottom surface of LED die and the lead frame is achieved through conductive paste. Any alignment fixture that is being applied during wave soldering should be loosely fitted and should not apply weight or force on LED. Non metal material is recommended as it will absorb less heat during wave soldering process. Note: In order to further assist customer in designing jig accurately that fit Avago Technologies product, 3D model of the product is available upon request. At elevated temperature, LED is more susceptible to mechanical stress. Therefore, PCB must allowed to cool down to room temperature prior to handling, which includes removal of alignment fixture or pallet. If PCB board contains both through hole (TH) LED and other surface mount components, it is recommended that surface mount components be soldered on the top side of the PCB. If surface mount need to be on the bottom side, these components should be soldered using reflow soldering prior to insertion the TH LED. Recommended PC board plated through holes (PTH) size for LED component leads. LED component lead size.4 x.4 mm (.18x.18 inch). x. mm (.2x.2 inch) Diagonal ANDOE.636 mm (.2 inch).77 mm (.28 inch) AlInGaP Device Plated through hole diameter.98 to 1.8 mm (.39 to.43 inch) 1. to 1.1 mm (.41 to.4 inch) Over-sizing the PTH can lead to twisted LED after clinching. On the other hand under sizing the PTH can cause difficulty inserting the TH LED. Refer to Application Note 334 for more information about soldering and handling of high brightness TH LED lamps. 9
Example of Wave Soldering Temperature Profile for TH LED 2 TURBULENT WAVE LAMINAR WAVE HOT AIR KNIFE Recommended solder: Sn63 (Leaded solder alloy) SAC3 (Lead free solder alloy) Flux: Rosin flux 2 Solder bath temperature: 24 C± C (maximum peak temperature = 2 C) TEMPERATURE ( C) 1 1 Dwell time: 1. sec - 3. sec (maximum = 3sec) Note: Allow for board to be sufficiently cooled to room temperature before exerting mechanical force. PREHEAT 1 2 3 4 6 7 8 9 1 TIME (MINUTES) Ammo Packs Drawing 6.3 ± 1.3.2 ±.1 12.7 ± 1.. ±.39 CATHODE 2. ± 1..87 ±.394 18. ±..78 ±.19 9.12 ±.62.39 ±.24 12.7 ±.3. ±.12.7 ±.2.276 ±.7 4. ±.2.17 ±.7 TYP. VIEW A - A Note: All dimensions in millimeters (inches) 1
Packaging Box for Ammo Packs FROM LEFT SIDE OF BOX ADHESIVE TAPE MUST BE FACING UPWARDS. LABEL ON THIS SIDE OF BOX ANODE LEAD LEAVES THE BOX FIRST. Note: For InGaN device, the ammo pack packaging box contain ESD logo Packaging Label (i) Avago Mother Label: (Available on packaging box of ammo pack and shipping box) (1P) Item: Part Number (1T) Lot: Lot Number LPN: (9D)MFG Date: Manufacturing Date STANDARD LABEL LS2 RoHS Compliant e3 max temp 2C (Q) QTY: Quantity CAT: Intensity Bin BIN: Refer to below information (P) Customer Item: (V) Vendor ID: (9D) Date Code: Date Code DeptID: Made In: Country of Origin 11
(ii) Avago Baby Label (Only available on bulk packaging) Lamps Baby Label (1P) PART #: Part Number RoHS Compliant e3 max temp 2C (1T) LOT #: Lot Number (9D)MFG DATE: Manufacturing Date QUANTITY: Packing Quantity C/O: Country of Origin Customer P/N: CAT: Intensity Bin Supplier Code: BIN: Refer to below information DATECODE: Date Code Acronyms and Definition: BIN: (i) Color bin only or VF bin only (Applicable for part number with color bins but without VF bin OR part number with VF bins and no color bin) OR (ii) Color bin incorporated with VF Bin (Applicable for part number that have both color bin and VF bin) Example: (i) Color bin only or VF bin only BIN: 2 (represent color bin 2 only) BIN: VB (represent VF bin VB only) (ii) Color bin incorporate with VF Bin BIN: 2VB VB: VF bin VB 2: Color bin 2 only DISCLAIMER: AVAGO S PRODUCTS AND SOFTWARE ARE NOT SPECIFICALLY DESIGNED, MANUFACTURED OR AUTHORIZED FOR SALE AS PARTS, COMPONENTS OR ASSEMBLIES FOR THE PLANNING, CONSTRUCTION, MAINTENANCE OR DIRECT OPERATION OF A NUCLEAR FACILITY OR FOR USE IN MEDICAL DEVICES OR APPLI- CATIONS. CUSTOMER IS SOLELY RESPONSIBLE, AND WAIVES ALL RIGHTS TO MAKE CLAIMS AGAINST AVAGO OR ITS SUPPLIERS, FOR ALL LOSS, DAMAGE, EXPENSE OR LIABILITY IN CONNECTION WITH SUCH USE. For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 2-29 Avago Technologies. All rights reserved. AV2-11EN - February 13, 29