Vision EV5-D2, EV5-D4 multi-switch installation

Vision EV5-D2, EV5-D4 multi-switch installation

Vision EV5-D2, EV5-D4 multi-switch installation. INTRODUCTION The introduction of the BSkyB Sky-Q set top box satellite receiver in 2016 also introduced a new standard of signal management that enables the set top box to receive up to 12 different satellite channels simultaneously via just one coax cable. This new standard of digital satellite channel reception (dscr) requires a signal switch capable of decoding and delivering signals in a dscr format. The new range of dscr switches from Vision are fully compatible with the Sky-Q specifications, provide up to 16 user bands per output in compliance with DiSEqC commands for Sky+, Sky+HD, SkyQ and satellite receivers built to comply with EN50494/EN50607 (SCR/dSCR) as well as Legacy (13V/18V/22kHz) commands. The EV5- dscr multi-switch will automatically detect which Sky receiver settings are required to operate the connected receiver. The switches are available in two ranges, each offered in a choice of output ports. The EV5-dSCR-M range uses a low voltage power supply connected directly to the dscr switch auxiliary DC input. The EV5 dscr-s models can be locally powered in addition to a line powering facility, permitting the powering from a subscriber location if this is more convenient. (see POWERING section of this handbook). Each switch is available as either (1) a two output (EV5-D2) and (2) a four output model (EV5-D4), Larger switches will be available in the future. All versions also feature UHF TV (terrestrial signal) gain at a similar level to the existing Vision EVO V5 range of IRS products, making upgrading an existing Vision EV5 system very simple and extremely fast. To further speed installation, the connector pitch and sequence exactly match existing Vision EV5 switches and taps, making physical connection very rapid indeed. The dscr switches also feature fully automatic level control, negating the need for any gain or level adjustments in most installations. It is also possible to build a dscr only cascaded multi-switch system for several dwellings or apartments from a standard 5-core trunk cable. Vision Products (Europe) Ltd offer a free planning service for installers and can advise on any aspect of installation of IRS and other TV signal systems, including fibre optic, MATV, CATV etc.

IMPORTANT WARNINGS The EV5-dSCR multi-switches are intended only for indoor installation or installation in a suitable weatherproof outdoor cabinet. These multi-switches must not come into contact with moisture or be installed in areas of high humidity or heat. Always mount the multi-switch securely to a wall or bulkhead panel so it cannot hang or swing on its coaxial cables as this may strain the internal circuit board and components. Always connect all of the coaxial cables to the multi-switch before connecting the power. These units are not designed to be hot-swapped or connected to a live system. Momentary short-circuit of any cables may be enough to damage the sensitive electronics within the multi-switch or the connected system. Always allow plenty of ventilation around the multi-switch and do not allow it to be covered with materials such as loft insulation. We recommend at least 5cm of airspace around the multi-switch. Digital products can get hot to the touch and require a flow of air to avoid overheating. Always earth-bond the output cables of the multi-switch before powering the system. Floating voltages can be created in an un-earthed system which may cause damage and can be dangerous. Vision EV5-dSCR multi-switches are designed only to work with normal Ku band (Sky) Quattro LNBs. The trunk lines, H: Lo and H: Hi, will pass DC at up to 2A in either direction. To avoid damage not covered by warranty DO NOT EXCEED THIS CURRENT. Do not operate the power slide switch unless you totally understand the power demands of the system and confirmed they are 2A or less. Damage caused by current overload is not covered by the manufacturer s warranty.

POWERING. There are 3 ways to power EV5-dSCR multi-switches. 1) By a stand-alone 18V power supply (EV5-034) into the DC in socket of the dscr multi-switch with the DC switch on the top of the multi-switch in the OFF position. Recommended. 2) By a stand-alone 18V power supply (EV5-034) into the DC in socket of the dscr multi-switch with the DC switch on the top of the multi-switch in the ON position. This allows the power supply to power a number of multi-switches and the LNB to build a cascaded system. Warning! Check the current consumption of all items on the system. They must not exceed the rating of the power supply or the DC 2A pass capability of the EV5-dSCR multi-switch. (EV5-D2 consumes 360mA. EV5-D4 consumes 720mA.) 3) With the DC switch on the top of the multi-switch housing in the ON position, the EV5-dSCR multiswitch will draw current and power from the trunk line of the existing system. WARNING! DO NOT EXCEED THE CURRENT CAPABILITY OF THE POWER SUPPLY OR SYSTEM. SERIOUS DAMAGE CAN OCCUR IF OVERLOADED. EV5-034 18V 2.5A PSU

INSTALLATION EV5-dSCR multi-switches are ideal for insertion between the tap and a multi-switch of a standard V5/EV5 IRS installation. Using the EV5-dSCR to upgrade a system in this way minimises disruption and ensures ongoing performance of the existing system. Insert the EV5-dSCR between the tap and multi-switch of an existing system. With the DC switch in the off position, power the dscr with its own power supply. Always leave the DC switch in the OFF position when inserting EV5-dSCR into an existing multi-switch installation. Power the EV5-dSCR at 18V using EV5-034 power supply connected to the auxiliary DC IN socket on the switch. Ensure the power supply is switched off before connection. WARNING! Adding EV5-dSCR may draw more current than the system is capable of delivering. Once fitted and connected, turn on the power supply and then connect the receiver(s). The multi-switch will then begin the process of auto-detecting the type(s) of receiver connected. This process may need to be repeated if a different type of satellite receiver is connected to the system. Please note: It may take several minutes for the receiver to download the EPG from the satellite provider.

The dscr user bands are pre-set in the multi-switch as follows:- Central frequency, MHz Sky dscr User Bands User Band PIN Code EN50494 EN50607 UB Number Centre MHz UB1 1 1210 1210 3 1680 UB2 2 1420 1420 9 1280 UB3 3 1680 1680 11 1380 UB4 4 2040 2040 14 1480 UB5 5 1284 1284 15 980 UB6 6 1516 1516 16 1030 UB7 7 1632 1632 17 1080 UB8 8 1748 1748 18 1130 UB9 9 970 19 1530 UB10 10 1010 20 1580 UB11 11 1050 21 1630 UB12 12 1090 22 1730 UB13 13 1130 23 1780 UB14 14 1170 24 1830 UB15 15 1330 25 1880 UB16 16 1370 26 1930

2017 Vision Products (Europe) Ltd, Redbourne Park, Liliput Road, Brackmills, Northampton NN4 7DT 01604 662748 www.vision-products.co.uk technical@vision-products.co.uk