USER INSTRUCTIONS X-CHIP-00-DIP X-CHIP-00-SMD X-CHIP-00-DIP, 5 RGB LEDs(DIP), Length=00mm with PCB module X-CHIP-00-SMD, 5 SMD RGB LEDs, Length=00mm with PCB module PRODUCTION DESCRIPTION X-CHIP is a simple 5 RGB LED module of the Cove Lite system and controlled by DMX technology. With its PCB module, compact profile and slim design, X- CHIP is available in mounting on fix stand provided. The X-CHIP can also be programmed and set through a LED Setup Tool(depicted here_xb-r). And in the Cover Lite system, X-CHIP-Driver(PCB) with 8 outputs as a driver unit and a tension provider is specially engaged in driving X-CHIP. Each driver unit enables to drive up to 8*50pcs units. And color effects and color changing modes can be created. For further information, please refer to its accompanying manual. A system connection should be set up before operation. It is great for advertisement signs, architecture decoration and entertaining applications. TECHNICAL SPECIFICATIONS COLOR RESOLUTION COLOR RANGE LIGHT SOURCE SOURCE LIFE OPERATION VOLTAGE VIEWING ANGLE POWER CONSUMPTION HOUSING ENVIRONMENT CONTROL CONNECTION LISTING OPERATING TEMPERATURE SIZE WEIGHT ACCESSORIES NOTICE: 4 Bit (RGB) 6.7 million of additive RGB colors with variable intensity 5 in RGB LEDs (5, 5 Green, 5 ), 5mm standard type, High Bright LED(Light Emitting Diodes) 5 SMD RGB LEDs, High Bright LED(Light Emitting Diodes) 50,000 hours under normal operating condition 4VDC 0 deg 48mA/RGB PCB module Indoor only Controlled by DMX 5 protocol (for further information, please refer to the product accompanying manual) Terminal(power/data interface) CE certified Range -0 degc ~ +50 degc 00(L) x 6(W)x9.5(H) mm 0g Fix stand & 5-color rainbow flat cable per unit All rights reserved! Specifications and improvement in the design of the unit and this manual are subject to change without prior notice. *Special Note: For reducing signal errors and avoiding signal transmission problems and interference, it is always advisable to connect 0 ohm impedance DMX signal cable and DMX terminator for signal connection. PHYSICAL DIMENSIONS X-CHIP-00-SMD X-CHIP-00-DIP 5 SMD RGB LEDs 5 RGB LEDs(DIP) Fix Stand(PCB Mounting KIT) -- Fix Stand(PCB Mounting KIT)
Programming A LED Setup Tool (depicted here _XB-R) is required to program X-CHIP-Driver(PCB) for the Cove Lite system. For further information, please refer to its accompanying manual.. Slave Control Mode(DMX Mode) In Slave Control, the settings for the addresses(00-5) and the Glide Effect functions can be adjusted with a LED Setup Tool. There are work modes for Slave Control. MODE- Standard mode(4 channels in total=8x3 channels) 8 RGB mode: has 8 groups with RGB output, of which each group consists of 3 channels(4 channels in total). (R/G/B) Channel -4 / Group -8 Output Output Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group Group Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 4 7 0 3 6 9 A LED Setup Tool(XB-R) (Sold separately) 5 8 4 7 0 3 3 6 9 5 8 4 MODE- and intensity mode(6 channels in total=8x channels) 8 C&B mode: has 8 groups with color and intensity C&B output, of which each group consists of channels (6 channels in total). Channel -6 / Group -8 Output Output Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group Group Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 3 5 7 9 3 5 4 6 8 0 4 6 MODE-3 mode(8 channels in total=8x channels) (3) 8 COLOR mode: has 8 groups with control, of which each group consists of channel (8 channels in total). The brightness is always 00% in this mode. Channel -8 / Group -8 Output Output Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Group Group Group 3 Group 4 Group 5 Group 6 Group 7 Group 8 3 4 5 6 7 8 00% 00% 00% 00% 00% 00% 00% 00% MODE-4 Patch mode RGB of 4 outputs----> outputs(4x3 channels) 4 RGB mode: in this mode, outputs are patched. The driver has 4 identical outputs distributed over 8 groups. Channel - / Group -4 Output - Output 3-4 Output 5-6 Output 7-8 (R/G/B) Group Group Group 3 Group 4 4 7 0 5 8 3 6 9 MODE-5 Patch mode C&B of 6 outputs---->8 outputs(4x channels) 4 C&B mode: has 4 groups with C&B output, of which each group consists of outputs that are controlled by channels(8 channels ly). Channel -8 / Group -4 Output - Output 3-4 Output 5-6 Output 7-8 Group Group Group 3 Group 4 3 5 7 4 6 8 --
MODE-6 Patch mode of 8 outputs---->4 outputs(4x channels) 4 COLOR mode: has 4 groups with control, of which each group consists of outputs that are controlled by channel(4 channels in total). The brightness is always 00% in this mode. Channel -4 / Group -4 Output - Output 3-4 Output 5-6 Output 7-8 Group Group Group 3 Group 4 3 4 00% 00% 00% 00% MODE-7 Patch mode RGB of 4 outputs---->6 outputs(x3 channels) RGB mode: in this mode, 4 outputs are patched. The driver has identical outputs distributed over groups. (R/G/B) Channel -6 Output -4 Output 5-8 Group Group 4 5 3 6 MODE-8 Patch mode C&B of 6 outputs---->4 outputs(x channels) C&B mode: has groups with C&B output, of which each group consists of 4 outputs that are controlled by channels (4 channels in total). Channel -4/Group- Output -4 Output 5-8 Group Group 3 4 MODE-9 Patch mode of 8 outputs---> outputs(x channel) COLOR mode: has groups with control, of which each group consists of outputs that are controlled by channel ( channels in total). The brightness is always 00% in this mode. Channel -/Group- Output -4 Output 5-8 Group Group 00% 00% MODE-0 Patch mode RGB of 4 outputs---->3 outputs(3x channels) RGB mode: in this mode, 8 outputs are patched. The driver has 4 identical outputs distributed over group. (R/G/B) Channel -3 Group / Output -8 3-3-
MODE- Patch mode C&B of 6 outputs----> outputs(x channels) C&B mode: has group with C&B output, which consists of 8 outputs that are controlled by channels. Channel - Group / Output -8 MODE- Patch mode of 8 outputs----> outputs(x channels) COLOR mode: has group with control, which consists of output that is controlled by channel. The brightness is always 00%. Channel Group / Output -8 NOTE: 00%. The Glide Effect function can be switched on(yes) or off(no). The transition from one level to another is smoother when this function is switched on.. When this function is switched off, the lighting intensity will changed from one level to another abruptly.(thus, when a quick lighting effect is required, the Guide Effect function should be switched off.) 3. If the DMX signal is interrupted, the driver will keep the last received DMX signal(information) until the driver is switched off or a new and valid DMX signal is sent..master Control AUTO mode and MANUAL mode are for Master Control. Relevant functions are as below: () AUTO mode: Preset programs:-0 programs and "AUTO" program ("AUTO" program is the sequential running of these-0 programs.) Auto Speed: ~00. Auto Fadetime: 0%~00%. () MANUAL mode: BLUE Dimmer: 0%~00%. RED Dimmer: 0%~00%. GREEN Dimmer: 0%~00%. NOTE:. The LEDs will turn red in Slave Control mode. The LEDs will give responding sensitive when the parameters are adjusted in Master Control.. If the LED is not selected in "Setup with answer", it will turn red. If the LED is not selected in :Setup no answer", it will switch off. When the user confirms the settings of the LED products, the LEDs will flash momentarily to confirm that the setting have been saved. -4-
TECHNICAL DRAWING-SYSTEM CONNECTION DIAGRAM 5-color rainbow flat-cable(l=00mm) between X-CHIPs X-CHIP-00-DIP or X-CHIP-00-SMD Power/Data Extension Starter cable (L=0.5~5m) to connect from the driver unit to first X-CHIP. X-CHIP-DRIVER or X-CHIP-DRIVER-PCB Driver Unit DMX In Terminal Connector B R G () () (Green) W Y (White) (Yellow) B () R () G (Green) W (White) Y (Yellow) Power In B R G W Y () () (Green) (White) (Yellow) Note: The cable must be connected correctly to the terminal connector as the required sequence! DMX Through for Next driver unit Or Power Supply Unit (Dc4v, 4A) AC00~40V DMX Controller XB-R offers function setup for X-CHIPs Please Note:. One driver unit with power supply of DC4v, 4A enables to drive up to 50pcs unit per port, a maximum of 400pcs units can be driven, total 8 ports.. One driver unit with one PSU(DC4v, 6.5A) enables to drive up to 50pcs per port, a maximum of 0pcs units can be driven, total 8 ports. -5-