Product Number : Product Name : PTDW0000 3Chip DLP Projector As of November 2008. Appearance and specifications are subject to change without notice. < >
3Chip DLP Projector PTDW0000 Specifications Main Unit Power supply: North America: Europe, Asia Power consumption: DLP chip: Panel size: Display method: Pixels: Lens: Lamp: Screen size: Brightness* : Centertocorner uniformity* : Contrast* : Resolution: Scanning frequency: RGB: YPBPR (YCBCR): SVideo/Video: Optical axis shift*: Vertical: Horizontal: Keystone correction range: Installation: Terminals: DVID IN: RGB IN: R, G, B: Y, PB, PR RGB2 IN: R, G, B: Y, PB, PR VIDEO IN: 20 V AC, 5 A, 60 Hz 220240 V AC, 5 A, 50/60 Hz,450 W (25 W in standby mode with fan stopped) 0.95 diagonal (6:9 aspect ratio) DLP device x 3 (R, G, B), DLP projection system 2,073,600 (,920 x,080) x 3, total of 6,220,800 pixels Optional powered zoom/focus lenses 250 W UHM lamp x 4 70 600 inches, 6:9 aspect ratio (70 300 inches with the ETD75LE5, 6:9 aspect ratio) 0,000 lumens (fourlamp operation mode) 90% 5,000: (full on/full off, in dynamic iris 3 mode),920 x,080 pixels (Input signals that exceed this resolution will be converted to,920 x,080 pixels.) Horizontal: 500 khz, Vertical: 24 20 Hz* 2, Dot clock: 2062 MHz 480i: fh 5.75 khz; fv 60 Hz, 576i: fh 5.63 khz; fv 50 Hz, 480p: fh 3.50 khz; fv 60 Hz, 576p: fh 3.25 khz; fv 50 Hz, 720/60p: fh 45.00 khz; fv 60 Hz, 720/50p: fh 37.5 khz; fv 50 Hz, 035/60i: fh 33.75 khz; fv 60 Hz, 080/60i: fh 33.75 khz; fv 60 Hz, 080/50i: fh 28.3 khz; fv 50 Hz, 080/25p: fh 28.3 khz; fv 25 Hz, 080/24p: fh 27.00 khz; fv 24 Hz, 080/24sF: fh 27 khz; fv 48 Hz, 080/30p: fh 33.75 khz; fv 30 Hz, 080/60p: fh 67.5 khz; fv 60 Hz, 080/50p: fh 56.25 khz; fv 50 Hz Horizontal: 5.75/5.63 khz, Vertical: 50/60 Hz, (NTSC, NTSC4.43, PAL, PAL60, PALN, PALM, SECAM) ±60% (±50% with the ETD75LE6) from center of screen, powered ±20% (±5% with the ETD75LE6) from center of screen, powered Vertical: ±40 (±22 with the ETD75LE5, ±28 wih the ETD75LE6) Ceiling/floor, front/rear DVID 24pin x, DVI.0 compliant, HDCP compatible, single link B x 5 G: 0.7 Vpp (.0 Vpp for sync on G), 75 ohms, B, R: 0.7 Vpp, 75 ohms HD, VD, SY:.45.0 Vpp, positive/negative automatic Y:.0 pp, 75 ohms (incl. sync signal), PB/PR: 0.7 Vpp, 75 ohms 0.7 Vpp (.0 Vpp for sync on G), 75 ohms NOTE: HD/SY, and VD terminals do not accept 3value direct sync signals. Dsub HD 5pin x 0.7 Vpp (.0 Vpp for sync on G), 75 ohms HD, VD, SY: TTL, high impedance, positive/negative automatic VD:.45.0 Vpp, positive/negative automatic, 75 ohms Y:.0 pp, 75 ohms (incl. sync signal), PB/PR: 0.7 Vpp, 75 ohms NOTE: HD/SY, and VD terminals do not accept 3value direct sync signals. B x,.0 Vpp, 75 ohms As of November 2008 < 2 >
3Chip DLP Projector VIDEO OUT: SVIDEO IN: LAN: SERIAL IN* 4 : SERIAL OUT* 4 : REMOTE IN: REMOTE OUT: REMOTE 2 IN: Optional board slot* 5 : With ETMD77SD installed: SERIAL IN: SERIAL OUT: With ETMD77SD3 installed: SERIAL IN: SERIAL OUT: With ETMD00SD4 installed: Link A/Link B IN: With ETMD77DV installed: DVID IN: PTDW0000 B x,.0 Vpp, active through Mini DIN 4pin x Y:.0 Vpp, C: 0.286 Vpp, 75 ohms (S signal compatible) RJ45 x, 0BaseT/00BaseTX, compatible with PJLink (class ) Dsub 9pin (female) x 2, for external control (RS232C/RS422 compliant) Dsub 9pin (male) x, for link control (RS422 compliant) M3 jack x for wired remote control M3 jack x for link control Dsub 9pin x for external control (parallel) B x, SDSDI signal (YCBCR 4:2:2 0bit): SMPTE 259M compliant: 480i, 576i B x, active through B x SDSDI signal (YCBCR 4:2:2 0bit): SMPTE 259M compliant: 480i, 576i Singlelink HDSDI signal (YPBPR 4:2:2 0bit): SMPTE 292M compiant: 720/50p, 720/60p, 080/50i, 080/60i, 080/25p, 080/24p, 080/24sF, 080/30p B x, active through B x for each SDSDI signal (YCBCR 4:2:2 0bit): SMPTE 259M compliant: 480i, 576i Singlelink HDSDI signal (YPBPR 4:2:2 0bit): SMPTE 292M compiant: 720/50p, 720/60p, 080/50i, 080/60i, 080/25p, 080/24p, 080/24sF, 080/30p Duallink HDSDI signal (RGB 4:4:4 2bit/0bit): SMPTE 372M compiant: 920 x 080/50i, 920 x 080/60i, 920 x 080/25p, 920 x 080/24p, 920 x 080/24sF, 920 x 080/30p Duallink HDSDI signal (X Y Z 4:4:4 2bit): 2048 x 080/24p, 2048 x 080/24sF DVID 24pin x, DVI.0 compliant, compatible with HDCP, single link EDID: 480p, 576p, 080/60i, 080/50i, 080/24p, 080/24sF, 080/25p, 080/30p, 080/60p, 080/50p, 720/60p, 720/50p EDID2: Compatible with noninterlaced signals only, Effective resolution: VGA (640 x 480) UXGA (,600 x,200) Dot clock: 2562 MHz NOTE: LAN terminals on the optional board can not be used. Use the LAN terminal Power cord: Cabinet material: Dimensions (W x H x D): Weight* 6 : Operating temperature* 7 : Operating humidity: on the projector. 3 m/9.8 Moulded plastic 578 x 320 x 643 mm (223/4 x 29/32 x 255/6 ) (without lens) Approx. 32 kg (70.5 lbs) (without lens) 0 45 C (32 3 F) 0%80% (no condensation) As of November 2008 < 3 >
3Chip DLP Projector Remote Control Unit Number of functions: Power supply: Operation range* 8 : Dimensions (W x H x D): Weight: PTDW0000 35 keys, 39 functions 3 V DC (AA battery x 2) Approx. 30 m when operated from directly signal receptor 5 x 22.7 x 76 mm (2 x 7/8 x 65/6 ) 34 g (4.7 oz) (including batteries) Supplied Accessories Power cord Wireless/wired remote control unit Batteries for remote control (x 2) Eye bolts (x 4) Wire rope Optional Accessories Zoom lens (0.9.:): Zoom lens (.4.8:): Zoom lens (.8 2.8:): Zoom lens (2.8 4.6:): Zoom lens (4.67.4:): Zoom lens (7.33.8:): Fixedfocus lens (0.7:): SDSDI board: HD/SDSDI board: Dual link HDSDI board: DVID board: Replacement lamp unit Ceiling mount bracket for high ceilings Ceiling mount bracket for low ceilings Frame Carrying handle Smoke cut filter ETD75LE6 ETD75LE ETD75LE2 ETD75LE3 ETD75LE4 ETD75LE8 ETD75LE5 ETMD77SD ETMD77SD3 ETMD00SD4 ETMD77DV ETLAD0000 (one unit) ETLAD0000F (a set of four lamps) ETPKD00H ETPKD00S ETPFD00 ETHAD00 ETSFD00 Weights and dimensions shown are approximate. Specifications subject to change without notice. * Measurement, measuring conditions, and method of notation all comply with ISO 28 international standards. *2 Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input. *3 Shift range is limited during simultaneous horizontal and vertical shifting. *4 Contact your dealers for details when the control using RS232C or RS422 is required. *5 The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit. *6 Average value. May differ depending on models. *7 Operating temperature is 0 C40 C (32 F04 F) when the fan control is set to HIGHLAND (for over,400 m to 2,700 m above sea level). *8 Operation range differs depending on environments. As of November 2008 < 4 >
3Chip DLP Projector PTDW0000 Shape of the plug receptacle 20V AC, 20 A 220240V AC, 6 A 220240V AC, 3 A/5 A G W Note: Be sure to use the power plug adaptor cord supplied with the projector. The supplied power plug adaptor can be used with the PTDW0000 only. Dimensions 20 (423/32 ) 448 (75/8 ) 28 (89/32 ) 36 (3/32 ) 643 (255/6 ) 607 (2329/32 ) unit : mm (inch) NOTE: This illustration is not drawn to scale. 578 (223/4 ) 320 (29/32 ) 265 (07/6 ) 477 (825/32 ) Terminals IN OUT RS232C IN RS422 IN RS422 OUT REMOTE SERIAL REMOTE 2 IN LAN IN R/PR G/Y B/PB OUT 2 3 4 5 6 SY/HD VIDEO SVIDEO IN RGB IN RGB 2 IN DVID IN 7 8 9 0 2 3 VD Remote input/output 2 Remote 2 input 3 Serial input (RS232C) 4 Serial input (RS422) 5 Serial output (RS422) 6 LAN connector (0BaseT/00BaseTX) 7 Video input 8 Video output 9 SVideo input 0 RGB (YPBPR) input RGB 2 Input 2 DVID input 3 Optional board slot As of November 2008 < 5 >
3Chip DLP Projector PTDW0000 Standard settingup positions * When the lens protrudes to the maximum. H Upper edge of projected image 46.5536.5 L Projected image L H (63/32 2/8 ) 44 mm (65/6 ) with the ETD75LE6 36.5 mm (25/32 ) with ETD75LE 30 mm (27/32 ) with the ETD75LE2 304.5 mm (2 ) with the ETD75LE3 328.4 mm (25/6 ) with the ETD75LE4 456.5 mm (73/32 ) with the ETD75LE8 404.5 mm (55/6 ) with the ETD75LE5 * 63 (63/32 ) Lower edge of projected image unit : mm (inch) L 57 (63/6 ) NOTE: Illustrations show the projector installed using optional ceiling bracket ETPKD00H and an optional lens. Projected image 87.5 (37/6 ) This illustration is not drawn to scale. Projection distance (screen aspect ratio 6:9) Lens (Throw ratio)* Screen size (inch, diagonal) 70 80 90 00 20 50 200 250 300 400 500 600 ETD75LE6 Zoom lens (0.9.:) min.,393 4.6,600 5.2,807 5.9 2,04 6.6 2,428 8.0 3,049 0.0 4,084 3.4 5,9 6.8 6,54 20.2 8,224 27.0 0,294 33.8 2,364 40.6 max.,662 5.5,90 6.3 2,58 7. 2,406 7.9 2,902 9.5 3,646 2.0 4,886 6.0 6,26 20.4 7,366 24.2 9,846 32.3 2,326 40.4 4,806 48.6 ETD75LE Zoom lens (.4.8:) min. 2,072 6.8 2,379 7.8 2,686 8.8 2,992 9.8 3,606.8 4,526 4.8 6,060 9.9 7,594 24.9 9,28 29.9 2,96 40.0 5,264 8,332 60. max. 2,768 9. 3,78 0.4 3,588.8 3,998 3. 4,87 5.8 6,047 9.8 8,096 26.6 0,45 33.3 2,94 40.0 6,292 53.5 20,390 66.9 24,488 80.3 ETD75LE2 Zoom lens (.8 2.8:) min. 2,80 9.2 3,22 0.5 3,624.9 4,035 3.2 4,858 5.9 6,093 20.0 8,50 26.7 0,208 33.5 2,265 40.2 6,380 53.7 20,495 67.2 24,60 80.7 Distance to screen max. 4,25 3.8 4,832 5.9 5,449 7.9 6,067 9.9 7,30 24.0 9,53 30.0 2,240 40.2 5,326 50.3 8,43 60.4 24,586 80.7 30,759 00.9 36,932 2.2 Zoom ETD75LE3 Zoom lens (2.84.6:) min. 4,226 3.9 4,843 5.9 5,460 7.9 6,077 9.9 7,32 24.0 9,64 30.0 2,250 40.2 5,337 50.3 8,423 60.4 24,596 80.7 30,769 00.9 36,942 2.2 max. 7,094 23.3 8,25 26.7 9,56 30.0 0,87 33.4 2,248 40.2 5,34 50.3 20,496 67.2 25,650 84.2 30,805 0. 4,4 34.9 5,423 68.7 6,732 202.5 ETD75LE4 Zoom lens (4.67.4:) min. 7,0 23.3 8,32 26.7 9,63 30. 0,93 33.4 2,255 40.2 5,348 50.4 20,502 67.3 25,657 84.2 30,8 0. 4,20 34.9 5,429 68.7 6,738 202.6 max.,374 37.3 3,03 42.7 4,652 48. 6,292 53.5 9,570 64.2 24,488 80.3 32,685 07.2 40,88 34. 49,078 6.0 65,47 24.8 8,864 268.6 98,257 322.4 ETD75LE8 Zoom lens (7.33.8:) min. max.,09 2,42 36.4 69.4 2,730 24,24 4.8 79.4 4,370 27,286 47. 89.5 6,009 30,358 52.5 99.6 9,288 36,50 63.3 9.8 24,207 45,77 79.4 32,404 6,076 06.3 200.4 40,602 76,435 33.2 250.8 48,799 9,794 60. 30.2 65,94 22,52 23.9 40.9 8,589 53,230 267.7 502.7 97,984 83,948 32.5 603.5 Fixedfocus ETD75LE5 Fixedfocus lens (0.7:) The figures in the above table may vary by approximately ±5% depending on the projection lens that is used. When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.,022 3.35,80 3.87,338 4.39,496 4.9,82 5.94 2,286 7.50 3,076 0.09 3,866 2.68 4,656 5.28 Zoom lenses except ETD75LE6 87 959 0.29 3.5 00,096 0.33 3.60 2,233 0.37 4.05 25,370 0.4 4.49 49,644 0.49 5.39 87 2,055 0.6 6.74 249 2,740 0.82 8.99 3 3,424.02.23 374 4,09.23 3.48 498 5,479.63 7.98 623 6,849 2.04 22.47 747 8,29 2.45 26.97 Height from the edge of screen to center of lens (H) Zoom lenses ETD75LE6 Fixedfocus lens 0 872 436 0 0 2.86 996.43 498 0 3.27.63 0,2 56 0 3.68.84 0,245 685 0 4.08 2.25 0,494 747 0 4.90 2.45 0,868 934 0 6.3 3.06 0 2,49,245 0 8.7 4.08 0 3,3,557 0 0.2 0 3,736 5.,867 0 2.26 0 4,98 6.3 0 6.34 0 6,226 0 20.43 0 7,472 0 24.5 millimeters feet As of November 2008 < 6 >
3Chip DLP Projector PTDW0000 Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. ETD75LE6 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 20.7 56.6 maximum L (mm) = (diagonal screen size in inches) x 24.8 73.6 ETD75LE 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 30.68 76 maximum L (mm) = (diagonal screen size in inches) x 40.98 00 ETD75LE2 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 4.5 80 maximum L (mm) = (diagonal screen size in inches) x 6.73 06 ETD75LE3 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 6.73 96 maximum L (mm) = (diagonal screen size in inches) x 03.09 22 ETD75LE4 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 03.09 6 maximum L (mm) = (diagonal screen size in inches) x 63.93 0 ETD75LE8 6 : 9 minimum L (mm) = (diagonal screen size in inches) x 63.95 386 maximum L (mm) = (diagonal screen size in inches) x 307.8 360 ETD75LE5 6 : 9 (fixed focus) L (mm) = (diagonal screen size in inches) x 5.798 84 The figures in the above table may vary by approximately ±5% depending on the projection lens that is used. When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. At the shortest projection distance, the zoom lens characteristics may cause slight image distortion. Mounting and Operation Precaution Do not mount the projector so that it angles downward from the vertical (including downward angles of ±45, because this would adversely affect its lamp cooling ability. For detailed information, please consult your sales representative. Shift range Optical axis shift function allows to shift the position of a projected image as shown below. ETD75LE/D75LE2/D75LE3/D75LE4/D75LE8 ETD75LE6 Heirght of projected image (V) 0.5V Standard position of projected image 0.5V 0.5V 0.6V Heirght of projected image (V) 0.5V Standard position of projected image 0.5V 0.6V 0.5V 0.5V 0.5V 0.5V 0.5V 0.2H Width of 0.2H projected image (H) 0.5H Width of 0.5H projected image (H) Because the ETD75LE5 is a fixed shortthrow lens, the lens shift function cannot be used with it. As of November 2008 < 7 >
3Chip DLP Projector PTDW0000 List of compatible signals This projector supports RGB signals with horizontal frequencies of 5 to 00 khz, vertical frequencies of 24 to 20 Hz and dot clock frequencies of 20 MHz to 62 MHz. NOTE: The native resolution of this projector is,920 x,080 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution. Display mode NTSC/NTSC4.43/PALM/PAL60 PAL/PALN/SECAM 525i (480i) 625i (576i) 525p (480p) 625p (576p) 750 (720)/60p 750 (720)/50p 25 (080)/60i 25 (080)/50i 25 (080)/24p 25 (080)/24sF 25 (080)/25p 25 (080)/30p 25 (080)/60p 25 (080)/50p VGA70 VGA85 VGA60 VGA67 VGA73 VGA75 VGA85 SVGA56 SVGA60 SVGA72 SVGA75 SVGA85 MAC6 XGA50 XGA60 XGA70 XGA75 XGA82 XGA85 XGA87i XGA00 XGA20 WIDE76860 WXGA80050 WXGA80060 MXGA7 MXGA75 MXGA85 MAC2 MSXGA60 SXGA50 SXGA60 SXGA66 SXGA72 SXGA75 SXGA85 SXGA+60 SXGA+72 SXGA+75 UXGA60 Display resolution (dots) 720 x 480i 720 x 576i 720 x 480i 720 x 576i 720 x 483 720 x 576,280 x 720,280 x 720,920 x,080i,920 x,080,920 x,080i,920 x,080 640 x 400 640 x 480 800 x 600 832 x 624,024 x 768,024 x 768i,024 x 768,280 x 768,280 x 800,52 x 864,52 x 870,280 x 960,280 x,024,400 x,050,600 x,200 Scanning frequency H V (khz) (khz) 5.7 5.6 5.7 5.6 3.5 3.3 45.0 37.5 33.8 28. 27.0 27.0 28. 33.8 67.5 56.3 3.5 37.9 3.5 35.0 37.9 37.5 43.3 35.2 37.9 48. 46.9 53.7 49.7 39.6 48.4 56.5 65.5 68.7 35.5 80.0 96.7 47.8 4.3 49.7 64.0 67.5 76.7 68.7 52.4 64.0 72.3 78.2 80.0 9. 65.2 78.8 82.2. The i appearing after the resolution indicates an interlaced signal. Line flicker occurs when an interlaced signal is input. 59.9 59.9 59.9 24.0 24.0 70. 85. 59.9 66.7 72.8 85.0 56.3 60.3 72.2 85. 74.6 70. 8.6 85.0 87.0 00.0 20.0 59.9 59.8 7.2 74.9 85.0 75. 66.3 72.0 85.0 72.0 Dot clock frequency (MHz) 3.5 3.5 27.0 27.0 48.5 48.5 25.2 3.5 25.2 30.2 3.5 3.5 36.0 36.0 40.0 49.5 56.3 57.3 5.9 65.0 78.8 86.0 94.5 44.9 05.0 30.0 79.5 68.0 83.5 94.2 08.0 2.5 00.0 08.0 88.0 08.0 25.0 35. 35.0 57.5 22.6 49.3 55.9 62.0 Format VIDEO/SVIDEO YPBPR/RGB YPBPR/RGB/DVI (EDID) RGB/DVI (EDID2) RGB/DVI (EDID/2) RGB/DVI (EDID2) RGB RGB/DVI (EDID2) As of November 2008 < 8 >
3Chip DLP Projector PTDW0000 Serial connector The serial connector complies with RS232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names Dsub 9pin (female) Serial input No. 2 3 4 5 Signal name TXD RXD GND Description Send data Receive data Connected internally Ground No. 6 7 8 9 Signal name CTS RTS Description Connected internally Connected internally Pin assignments and signal names Dsub 9pin (male) Serial output No. 2 3 4 5 Signal name RXD TXD GND Description Receive data Send data Connected internally Ground No. 6 7 8 9 Signal name RTS CTS Description Connected internally Connected internally Communication conditions (factory setting) Signal level Synchronization method Baud rate Parity Character length Stop bit X parameter S parameter RS232Ccompliant Startstop synchronization 9,600 bps None 8 bits bit None None Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. STX A D I I2 ; C C2 C3 : P P2... Pn ETX Start ( byte) ID 2 characters (2 bytes) ID designator: 0 to 64: Address number 0A to 0Z: Group ID ZZ: All units (ID ALL) Semicolon ( byte) Colon ( byte) Command (3 bytes) (Control and/or query commands) Parameters (undefined length) End ( byte) CAUTIION It may not be possible to send or receive commands for about 0 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the timeout period for command response to 0 seconds or more. As of November 2008 < 9 >
3Chip DLP Projector PTDW0000 Cable specifications Projector PC (DTE) 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 Control commands Command : Parameter Function Callback PON POF IIS:RG IIS:RG2 IIS:VID IIS:SVD IIS:DVI IIS:AUX LPM:0 LPM: LPM:2 LPM:3 LPM:4 LPM:5 LPM:6 LPM:7 LPM:8 LPM:9 LPM:0 LPM: LPM:2 LPM:3 OSH: OSH:0 OPP:0 OPP: OPP:2 OPP:3 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA OTE:0 OTE: OTE:2 OTE:4 OTE:9 OTE:0 TSD:yy2y3y4mm2dd2w TST:hh2mm2ss2 OOS: OOS:0 POWER (STANDBY) INPUT SELECT LAMP SELECT SHUTTER P IN P SELECT AUTO SETUP PICTURE MODE COLOR TEMPERATURE DATE TIME ON SCREEN Standby power on Standby power off RGB RGB 2 Video SVideo DVI AUX Quad (four lamps) Lamp + 4 Lamp 2 + 3 Dual (two lamps) Lamp + 2 + 3 Lamp + 2 + 4 Lamp + 3 + 4 Lamp 2 + 3 + 4 Triple (three lamps) Lamp Lamp 2 Lamp 3 Lamp 4 Single lamp Shutter on Shutter off P in P off User User 2 User 3 Natural Standard Dynamic Cinema Graphic Low Middle High User User 2 Default Date setting Time setting Onscreen display on Onscreen display off PON POF IIS:RG IIS:RG2 IIS:VID IIS:SVD IIS:DVI IIS:AUX LPM:0 LPM: LPM:2 LPM:3 LPM:4 LPM:5 LPM:6 LPM:7 LPM:8 LPM:9 LPM:0 LPM: LPM:2 LPM:3 OSH: OSH:0 OPP:0 OPP: OPP:2 OPP:3 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA OTE:0 OTE: OTE:2 OTE:4 OTE:9 OTE:0 TSD:yy2y3y4mm2dd2w TST:hh2mm2ss2 OOS: OOS:0 As of November 2008 < 0 >
3Chip DLP Projector PTDW0000 Status asking commands Command:Parameter Function Callback Description QPW QSH QIN QOS QST Q$L: Q$L:2 Q$L:3 Q$L:4 QSL QIB QPP QGD QGT Main power status Shutter function status Input signal status Onscreen display status Projector run time Lamp run time Lamp 2 run time Lamp 3 run time Lamp 4 run time Lamp operation mode status Optional board slot status P in P status Date setting status Time setting status * * 2 Day of week: Monday =, Tuesday = 2,... Sunday = 7 Set the date and time to UTC (universal time coordinated). 00 000 0 RG RG2 VID SVD DVI AUX 0 0000099999 00009999 00009999 00009999 00009999 0 2 3 4 5 6 7 8 9 0 2 3 MD95SD MD95SD3 MD75DV NONE UNKNOWN NOT SUPPORT 0 2 3 yy2y3y4mm2dd2w hh2mm2ss2 NOTE: If a wrong command is received, the projector will send an ER40 or ER402 command to the computer. On Off On Off RGB RGB 2 Video SVideo DVI AUX On Off 00000h99999h 0000h9999h 0000h9999h 0000h9999h 0000h9999h Quad (four lamps) Lamp + 4 Lamp 2 + 3 Dual (two lamps) Lamp + 2 + 3 Lamp + 2 + 4 Lamp + 3 + 4 Lamp 2 + 3 + 4 Triple (three lamps) Lamp Lamp 2 Lamp 3 Lamp 4 Single lamp ETMD95SD ETMD95SD3 ETMD75DV Uninstalled Unknown Not supported Off User User 2 User 3 yyyymmdd (day of week) (*) hhmmss (*2) Command example To set the onscreen display off, send the command as shown below. STX ADZZ ; OOS : 0 ETX Start Character code 02 ID Address ZZ: ID ALL Command Parameter End Character code 03 NOTE: When sending commands without parameters, a colon (:) is not necessary. As of November 2008 < >
3Chip DLP Projector PTDW0000 Notes on Projector Placement and Operation: The projector uses a highwattage lamp that becomes very hot during operation. Please observe the following precautions.. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm (9/6 ) or more around the projector s exhaust openings. 3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated below between them. These space requirements also apply to installations where only one projector unit is operating at one time and the other unit is used as a backup. 4. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0 C/32 F and 40 C/04 F. Also make sure the projector s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings. 500 mm (9/6 ) or more 500 mm (9/6 ) or more* 500 mm (9/6 ) or more* Do not stack projector units directly on top of one another. * When two units are used together. 300 mm (3/6 ) or more for a single unit operation. Direction of Air Intake and Exhaust Intake Exhaust Operating the Projector Continuously. If the projector is to be operated continuously 24 hours, use the lamp relay mode. The projector cannot be operated continuously 24 hours in quadlamp mode. Allow a minimum of two hours per day of nonoperation time if the projector is to be operated continuously more than 22 hours. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export control regulations. DLP and the DLP logo are trademarks of Texas Instruments. The PJLink is an application trademark in Japan, the United States, and other countries and regions or registered trademarks. All other trademarks are the property of their respective trademark owners. As of November 2008 < 2 >