User manual Truss Light COB LED 30W
User manual Focusing tube Truss Light COB LED 30W 2 / 11
Table of contents 1. Safety instructions... 4 1.1. FOR SAFE AND EFFICIENT OPERATION... 4 2. Technical data... 5 3. Operating Instruction:... 5 3.1. MENU structure... 5 4. DMX Mode Chart... 7 4.1. DMX 1 (1channel)... 7 4.2. DMX 2 (2 channels)... 7 4.3. DMX 5 (5 channels)... 7 4.4 DMX 7 (7 channels)... 7 5. Set color in stand-alone mode (Saved)... 8 6. Photometric data... 9 3 / 11
1. Safety instructions This device is suitable for indoor use only. All modifications to the device will void the warranty. Repairs are to carry out by skilled personnel only. Use only fuses of the same type and original parts as spare parts. Protect the unit from rain and humidity to avoid fire and electric shocks. Make sure to unplug the power supply before opening the housing. 1.1. FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance. Not put it in a temperature bellow 32 F /0 C, or exceeding 104 F /40 C. Keep away from humidity, water and dust Do not place the set in a location with high humidity or lots of dust. Containers with water should not be placed on the set. To avoid placing on un-stable location Select a level and stable location to avoid vibration. Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. If out of work, contact sales agency immediately Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not open the cabinet by yourself, it might result a danger of electric shock. Take care with the power cable Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not using the device for an extended period of time, be sure to disconnect the plug from the receptacle. Important: Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Make sure the electrical connection is carried out by qualified personnel. All electrical and mechanical connections have to be carried out according to the European safety standards. 4 / 11
2. Technical data Voltage 100-240V; 50/60Hz Power consumption max. 40W Current max. 0,2A DMX 512 Connector 3 Pin XLR Weight 2.1 kg Measures (L x W x H) 148x 129x 220mm Max. ambient temperature 0-40 C Max. Housing temperature 60 C Fuse F1A, 250V Channels 7 Count of LEDs COB 30W RGB LEDs Scattering angle 20 (10 focusing tube) Protection class IP20 3. Operating Instruction: Four Buttons: Menu, Up, Down, Enter Four digital display dormant state after one minute working, Focusing tube: It can focus the beam from 20 degrees to 10 degrees. Without tube Fit tube on DATA INPUT & OUTPUT DC power input 3.1. MENU structure Menu Addr 1 DMX address adjust: 1 512 512 Shnd Sh 1 Sh 1 Sh 19: 19 programs 5 / 11
SPEd Sh 19 Sh 20 Sh n automatic run through all programs Sound programs 0 Program speed adjust 31 0=off 1-31=slow-fast SLAU SLA Light working master SLnd Soun node 0 Mast Light working master SL 1 SL 4 5 lve Slave mode OFF 4 DMX modes: SL 1 SL 4 Off: Close sound mode 1-100 1-100: sound sensitivity adjust 1 static color change 2 sound flash color change MASt On/Off On: open master signal, Off: close master signal ALLC 0 100 Setup LED master dimmer red 0 100 Setup red LED dimmer gree 0 100 Setup green LED dimmer blue 0 100 Setup blue LED dimmer Sate Ygs/no Ygs: close System LED, no: open system LED LEd ON/OFF Switches display on/off STEF OFF OFF = close test function 1 Test red LED 2 Test green LEDs 3 Test blue LEDs disp disp/dsip Display normal or inversion Vgr Readout software version rset Reset all values of the system updt 0-50 Press Enter and UP-button to 50 to update sign ON/OFF ON for master freeze, OFF for master blackout CoLr Temp 1 Red 2 Green 3 Blue 4 Orange 5 Magenta 6 Cyan Note: If you switch the device off the color is not saved. (For saving read Ch. 5) Displays system temperature Tips: Push the MENU-button to reach the first menu and use the UP/Down-buttons to get to submenu. To open the submenu you have to push the ENTER-button, here you can also reach other menu items with the UP/DOWNbuttons, confirm with ENTER. Push the MENU-button to store you settings. 6 / 11
4. DMX Mode Chart 4.1. DMX 1 (1channel) DMX Value Function Channel 1 0-255 0 = Off 1-255 = 36 different color macros 4.2. DMX 2 (2 channels) DMX Value Function Channel 1 0-255 0 = Off 1-255 = 36 different color macros 2 0-255 0 = Off 1-255 = Master dimmer 4.3. DMX 5 (5 channels) DMX Value Function Channel 1 0-255 Adjust red LEDs dimmer low to high 2 0-255 Adjust green LEDs dimmer low to high 3 0-255 Adjust blue LEDs dimmer low to high 4 0-255 0-8 = LED flash off 9-255 = speed of shutter slow-fast 5 0-255 0 = Off 1-255 = Master dimmer 4.4 DMX 7 (7 channels) 7 / 11
DMX Value Function Channel 1 0-255 Adjust red LEDs dimmer low to high 2 0-255 Adjust green LEDs dimmer low to high 3 0-255 Adjust blue LEDs dimmer low to high 0-8 0-8 = LED flash off 4 9-255 9-255 = speed of shutter/special functions slow-fast, sound sensitivity, NOTE: 0-128 static color change, >129 flash color change 5 0-255 0 = Off 1-255 = Master dimmer special functions 0-10 LED flash 11-20 automatic dimming (upwards) 21-30 automatic dimming (downwards) 31-40 automatic dimming (upwards/downwards) 41-50 automatic color chase change 6 51-60 Color change (3 colors) 61-70 color change (7 colors) 71-80 program 6 81-90 program 17 91-100 program 18 111-120 program 19 >120 music controlled color change 7 0-255 Speed of special functions or sound sensitivity 5. Set color in stand-alone mode (Saved) To set a color in stand-alone mode which is saved if you switch the device off you have to make following settings. 1. Press MENU 2. Step to the point Shnd and press ENTER. 3. Set Sh10 Sh16 (depending on the required color) and confirm with ENTER. Sh10 Flash red Sh11 Flash green Sh12 Flash blue Sh13 Flash magenta Sh14 Flash orange Sh15 Flash cyan Sh16 Flash white 4. Step to SPEd and set it to 0 an confirm with ENTER. 5. Now step to SLnd an set it to MASt an confirm with ENTER. 6. With the menu point ALLC you can dim the light. 8 / 11
Now you can switch the device off and the color is saved if you switch it on again. To set your own color mixing you have to make following settings. 1. Press MENU. 2. Step to Shnd and press ENTER. 3. Set Sh16 and confirm with ENTER. 4. Step to red, gree or blue to adjust the single colors. Confirm your settings with ENTER. 5. With the menu point ALLC you can dim the light. 6. Photometric data 9 / 11
10 / 11
Importer: B & K Braun GmbH Industriestraße 2 D-76307 Karlsbad www.bkbraun.com info@bkbraun.com 11 / 11