OPERATION MANUAL WING RGB LED WALL WASHER Version 1.3 June 2011
Philips Selecon has packaged this product using environmentally friendly packaging. Please consider either reuse of the packaging or dispose of responsibly with your nearest recycling collection agency. THANK YOU FOR PURCHASING A PHILIPS SELECON WING RGB LED WALL WASHER LUMINAIRE. WE HAVE DESIGNED THIS LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN AND ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR MANY YEARS TO COME. We recommend making a note of the serial numbers of your purchased luminaires for future reference. (The serial number can be found on the sticker at the top of the luminaire and on the box the luminaire was packed in). Caution! Installation is entirely at your risk. Read this manual from cover to cover before attempting installation. Do not attempt installation unless you are suitably qualified. If you do not understand a point in this manual, don t guess. Don t take short cuts. If in doubt, stop! Contact Philips Selecon or one of its authorised distributors for advice. Don t be afraid to ask for help. These luminaires are not suitable for outdoor use. They do not have an IP rating. This product has the following certifications: 2of17
Important! Read this manual from cover to cover before attempting to install, operate or maintain the luminaires to which it relates. It contains important installation, operating, maintenance and safety procedures. The customer must strictly comply with them. Along with such procedures mentioned in this document, the customer should also observe such other procedures generally applicable to lighting equipment. Follow the instructions in this manual carefully. Philips Selecon accepts no responsibility if the customer fails to do so. For each customer, operating conditions will vary, sometimes greatly. Such variations may affect the luminaires performance. Philips Selecon has no control over the customer s unique operating environment. Hence, Philips Selecon makes no representations or warranties concerning the luminaires performance under the customer s actual operating conditions. All operating parameters must be validated for each customer application by the customer s technical experts. If the customer does not follow the installation, operating, maintenance and safety procedures in this manual, as well as those generally applicable to lighting equipment, the luminaire may not perform as expected. More seriously, it may cause property damage, personal injury or other losses. Philips Selecon accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from the customer s failure to follow the installation, operating, maintenance and safety procedures in this manual or those generally applicable to lighting equipment. The foregoing limitation extends to damages for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time, whether incurred by the customer, the customer s employees or a third party. Philips Selecon used all due care in preparing this manual. However, Philips Selecon accepts no liability for errors or omissions. Philips Selecon reserves the right to change the specifications of its luminaires, or the information in this manual, without necessarily giving its customers notice thereof. Installation, operation and maintenance are entirely at the customer s risk. Philips Selecon luminaires should be installed, operated and maintained by suitably qualified personnel. Such personnel should have previous experience with lighting equipment as well as general electrical experience. This manual is intended to provide general guidance to such suitably qualified personnel. For specific guidance and technical support, contact Philips Selecon or its authorised representative. Information in this manual shall not be deemed a warranty, representation or guarantee concerning a luminaire s suitability or fitness for a specific purpose. Subject to the right to use its luminaires, Philips Selecon does not convey any right, title or interest in its intellectual property, including, without limitation, its patents, copyrights and know-how. 3of17
Contents Product Codes... 5 Wing RGB LED Wall Washer Configurations... 5 Accessories... 5 Installation... 6 Electrical Installation... 6 Wing LED Applications... 6 Pan and Tilt Adjustment... 7 Accessory Installation... 7 Barndoor... 7 Colour Frame... 7 Control... 8 DMX512... 8 DMX Installation Wiring... 8 DMX Addressing... 8 DMX personalities... 9 DALI...11 Remote Device Management (RDM)...12 RDM dimming curve...14 Service and Maintenance...14 End-of-life behaviour...14 Upgradeable...14 System disposal...14 LIMITED 3-YEAR WARRANTY...15 Product specification...16 Contacting Philips Selecon...17 4of17
Product Codes Wing RGB LED Wall Washer Configurations WWLEDRGBT01/ WWLEDRGBT03 White/Black Wing RGB LED Wall Washer fitted with DMX XLR-5 In/Out and track mount adapter. WWLEDRGBC01/ WWLEDRGBC03 White/Black Wing RGB LED Wall Washer fitted with DMX XLR-5 In/Out and ceiling rose mount. WWLEDRGBHC01/ WWLEDRGBHC03 White/Black Wing RGB LED Wall Washer fitted with DMX XLR-5 In/Out and half coupler mount with 1.0m cable and plug. Accessories WWLEDBD0103 Wing LED Barndoor White exterior, Black interior WWLEDBD03 Wing LED Barndoor Black WWLEDCF03* Wing LED Colour Frame (Black) *Note: the barndoor accessory is required if you wish to use a colour frame in the Wing LED as the barndoor creates the slot to hold the colour frame. For spare parts details contact your Philips Selecon dealer or visit www.seleconlight.com/wingled for the exploded drawings. 5of17
Installation Electrical Installation WARNING!!! Risk of fire and electric shock. This product is to be installed by a qualified electrician only. Ensure that the AC power is switched off before attempting to make any wiring connections. This fixture employs a grounded type receptacle and is not intended for connection to a two-wire, ungrounded source of supply. To avoid the chance of product damage or malfunction, disconnect power before connecting wires, and do not connect or disconnect cables (supply, data, lamps and interface cables) when voltage is supplied to the luminaire. Mains Voltage: 120-277VAC. (unit must be direct switching mains only, not via a dimmer system). When installing this fixture use wire conductor colour codes as follows: Brown - Phase, live Blue - Neutral, return Green/Yellow - Earth Notes: 1. For ceiling rose models minimum 60 C supply conductors to be used. 2. Track adapter variants are only to be fitted to approved and compatible track systems. Wing LED Applications The Wing range has been designed to meet demanding quality light level applications such as museums and galleries multiple units are required to obtain a visually even wash of light. Recommended spacing of luminaires is to have the luminaires at equal spacing to the distance from the wall. For example if the luminaires are 1.5m away from the wall the optimum spacing between the luminaires for an even wash of light would also be 1.5m. For optimum light distribution the Wing has been designed to be installed at a 45deg nominal angle as indicated. Ambient Operating Temperature: -10 C to 40 C To guarantee product lifetime, the user should ensure that the ambient temperature remains within the recommended temperature range. The Wing RGB LED Wall Washer is a high power LED product with high optical output. Operators of the LED modules should not look directly into the beam of the light source (especially not with magnifiers or similar optical instruments) as this may cause damage to the eyes. Further information relating to the lux levels, luminaire spacings and IES/ILUMUDAT files can be found at www.seleconlight.com/ies and www.seleconlight.com/ilumudat 6of17
Pan and Tilt Adjustment Adjusting the pan angle Release the set screw above the joint (as shown) and adjust accordingly. Relock after adjustment. Adjusting the tilt angle The tilt can be adjusted by unlocking the hex screw located as shown. Re-lock after adjustment. Accessory Installation Barndoor To install the barndoor, first hook it in to the slots on the front face and swing the barndoor up. Secure the barndoor with the two hex screws in the barndoor. Tighten these using a 3mm allen key until they are secure. DO NOT OVERTIGHTEN as this causes undue stresses in the parts. Secure barndoor here. DO NOT OVERTIGHTEN. Colour Frame The colour frame slots in between the barndoor and the front of the Wing LED luminaire. Note: the barndoor accessory is required if you wish to use a colour frame in the Wing LED as the barndoor creates the slot to hold the colour frame. 7of17
Control The Wing RGB LED Wall Washer can be controlled using either DMX or DALI protocol. DMX512 Units ordered with DMX control will be fitted with XLR5 in/out connectors. Basic DMX512 installation consists of connecting multiple Wing RGB LED Wall Washer luminaires together in daisy-chain fashion. An XLR5 cable is run from the control console (or alternative DMX control source) to the XLR5 male/input connector on the first luminaire. The following units are then connected out/in using the female/out XLR5 connector on the unit linking to the male/input XLR5 connector on the next, and so on. DMX Installation Wiring In order to ensure stable network communications, it is recommended that the DMX cable should be terminated with a 110 Ohm resistor between the Data+ and Data- wires at the end of the cable run. This prevents DMX signal reflections back to the DMX controller. Please refer to the diagram on the left for a typical DMX wiring configuration. To avoid the chance of product damage or malfunction, disconnect power before connecting wires, and do not connect or disconnect cables (supply, data, lamps and interface cables) when voltage is supplied to the LED driver or LED module. DMX Addressing The default address for the Wing RGB LED Wall Washer is 001. The individual luminaire DMX address can be set by using an RDM controller (parameter ID DMX_START_ADDRESS ) (see the Supported RDM Parameters section on pages 12 & 13) We recommend using the Philips Entertainment DMX Fix Tool/RDM Controller (Order Code 75851), available from your Philips Entertainment dealer. The luminaire requires between 2 to 10 DMX addresses, depending on the DMX personality. The DMX Personalities table (page 9) summarizes the DMX data assignment for each DMX personality. 8of17
DMX personalities There are two categories of DMX operation Static and Dynamic. Within these two categories, there is a subset of DMX personalities of operation. The default DMX personality for the Wing LED RGB is Static RGB, described in the Static DMX Personalities section. The DMX personality can be set by using an RDM controller (described in the DMX-RDM Personality section) Please refer to the DMX Personalities table, below, for the description of the DMX personalities. 9of17
Static DMX Personalities Refer to the DMX personalities table for the specific DMX byte assignment for each DMX personality a. Static RGB (3 DMX channels) This DMX personality utilises the most widely understood method of specifying chromaticity with LED-based luminaires, and is recommended for applications where both colour and white chromaticity points (e.g., 2700K- 6500K white, red, green, blue, cyan, magenta, yellow) are specified. This personality can be used to generate white points (ie specific CCT values) however this will be less accurate compared to using the CCT DMX personality. A table of RGB to CCT conversion values is required for this. 10of17
b. Static XY (3 DMX channels) This DMX personality enables the user to specify the (x,y) colour coordinates colour and intensity. There are 3 channels of output available for the DMX controller, one for the x coordinate, one for the y coordinate and one for intensity from 0% - 100% c. Static CCT (2 DMX channels) This DMX personality is recommended for applications where only white chromaticity points are specified. There are 2 channels of output available for the DMX controller, one for CCT value within the range of 2700K 6500K and the other for intensity from 0% - 100%. Dynamic DMX Personalities The following dynamic DMX personalities are available. (Refer to the DMX Personalities table for the specific DMX byte assignment for each DMX personality.) There are 3 main benefits for the dynamic DMX personalities: 1. Flexibility The user can program a DMX scene with different DMX inputs with minimal effort. (For example, one can achieve a rainbow wash comprising both saturated (RGB) colours and CCT white points by using the dynamic RGB and dynamic CCT DMX personality, by adjusting the 7 DMX offset bytes.) 2. Controllability The user can control the master intensity level and the fade times without the use of sophisticated 3rd party DMX control software/hardware. (For example, one easily adjusts the master intensity level for multiple Wing RGB LED Wall Washer units connected to the DMX network by adjusting the appropriate DMX byte values.) 3. Accuracy / Resolution For the dynamic CCT, xy and u v DMX personalities, 2 bytes are used to control the desired colour/white points compared to just 1 byte in the static DMX personalities. DALI The Digital Addressable Lighting Interface (DALI) is a digital protocol for controlling lighting components, such as electronic ballasts and dimmers, in buildings. Please refer to the diagram below for a typical DALI wiring configuration: 11of17
Remote Device Management (RDM) RDM is currently an open standard in development. This is an enhancement to USITT DMX512 for configuration, status monitoring, and the management of DMX512 based systems. This standard was developed by the ESTA Technical Standards Program and is designed for interoperability between a number of manufacturers. The Wing RGB LED Wall Washer system is RDM Compliant. RDM is mainly used in commissioning and service operations, whereas DMX512 is mainly used as the controlling protocol. The RDM Utility of the Wing RGB LED Wall Washer can be used to retrieve and modify properties for Wing RGB LED Wall Washer modules. 12of17
1) Responders and Controllers identify themselves with a 48-bit Unique ID (UID). The Unique ID (UID) consists of a 16-bit ESTA assigned Manufacturer ID with a 32-bit Device ID 2) The Parameter ID is a 16-bit number that identifyes a specific type of Parameter Data 13of17
RDM dimming curve The factory default setting is the square law dimming curve. It is strongly recommended that the dimming curve be kept at the default factory setting, because the square law matches very closely with the human response. The following table summarizes the available options: Service and Maintenance Philips Selecon has manufactured this luminaire in accordance with recognised best practices to recommended international safety standards. It is your responsibility to maintain this luminaire in good and safe working condition. The light emitting region on the front of the Wing RGB LED Wall Washer should be kept free from dirt, grease and other contaminants in order maintain optimal performance. Use only a soft, dry, lint-free cloth to clean the optics. Never use cleaning solvents as these may damage the optics. The above are the only maintenance tasks that can be safely carried out by non-approved personnel. For all other service and maintenance issues, please contact your Philips Selecon dealer. Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with damaged cable, track adapters etc. Only replace damaged parts with authorised spares. End-of-life behaviour Unlike typical conventional light sources, LEDs are not subject to sudden failure or burnout. There is no time at which the light source will cease to function. Instead, the performance of LEDs shows gradual degradation over time. When used according to specification, Wing RGB LED modules are predicted to deliver an average of 70% of their initial intensity after 35,000 hours operation. The life of the system is therefore more dependent on the other electronic system components and soldering methods. Upgradeable The simple modular configuration of the Wing RGB LED Wall Washer units this allows the units to be easily upgraded. As LED technology improves there higher performance modules will become available. These will be easy to swap in to the Wing LED units in order to upgrade them to the best possible version available without having to purchase a whole new unit. System disposal At the end of their (economic) lifetime, appropriate disposal of the Wing RGB LED Wall Washer unit, and it s components, is recommended. The modules are basically normal pieces of electronic equipment containing components that at present are not considered to be harmful to the environment and that can be disposed of with normal care. It is therefore recommended to dispose of these parts as normal electronic waste, according to local regulations. 14of17
LIMITED 3-YEAR WARRANTY Philips Selecon warrants its luminaires against defects in materials or workmanship. The term of this warranty is based on the product usage and is from the date of delivery. Architectural, Display relates to typical usage such as display lighting in a Museum viz: 10 12 hrs per day, seven days per week. This warranty is void in any of the following circumstances: (a) The luminaire has been misused, neglected, damaged or abused. (b) The luminaire has been improperly installed, operated, repaired or maintained. (c) The luminaire has been modified. (d) The luminaire has been connected to other equipment with which it is not compatible. (e) The luminaire has been used or stored in conditions outside its electrical or environmental specifications. (f) The luminaire has been used for purposes other than for which it was designed. (g) The luminaire has been used outside its stated specifications and operating parameters. Correct installation of the luminaire is the owner s responsibility. To assert a warranty claim, complete Philips Selecon s return authorisation form (available from Philips Selecon). Return the luminaire to Philips Selecon or its authorised agent. If Philips Selecon accepts the warranty claim, Philips Selecon will provide, or arrange for, service, repair or replacement as Philips Selecon shall determine in its sole discretion. Philips Selecon shall bear the cost of such service, repair or replacement. However, the owner shall bear the cost of freight and insurance on the luminaire, both ways. If Philips Selecon does not wish to service, repair or replace the defective luminaire, it shall refund the purchase price. Philips Selecon s sole responsibility is to repair, replace or service a luminaire subject to a valid warranty claim. Under no circumstance will Philips Selecon be liable for direct, indirect, incidental, special or consequential costs or damages, including dismantling and re-installation costs, loss of operations or profits, to the maximum extent permitted by law. Philips Selecon accepts no liability for personal injury or property damage resulting from failure to heed relevant operating and safety procedures specified by Philips Selecon or imposed by law. This is an express warranty. Philips Selecon disclaims any other express or implied warranties, including warranties of merchantability or fitness for purpose, to the maximum extent permitted by law. Some jurisdictions do not allow limitations or disclaimers of implied or statutory warranties. Some jurisdictions do not allow disclaimers or exclusions of consequential or incidental damages. Therefore, the above disclaimers, limitations and exclusions may not apply in all jurisdictions in which Philips Selecon sells its luminaires. This warranty gives the owner specific legal rights. The owner may have other rights or remedies pursuant to the laws in its territory. Nothing in this limited warranty should be construed as limiting or restricting any other statutory right or remedy of the owner, except for such limitations or restrictions herein as may be allowed by the law of the territory. Philips Selecon has a policy of continual product improvement and specifications are subject to change without notice. 15of17
Product specification Maximum Power Consumption: 40W Input Voltage: 120-277V Input Frequency: 50-63Hz Dimming: 100-10% without colour shift Lumen maintenance @ 35k hrs: 70% Colour Temperature: 2700-6500K RGB: R x=0.610, y=0.320 G x=0.250, y=0.610 B x=0.200, y=0.160 Control Interface: Dali or DMX/RDM Ambient Operating Temperature: Minimum -10 C Maximum 40 C UV and IR PET Value Damage Factor IR (infrared) radiation >100hrs/Klux (zero UV) 0.08 @ 4100K As well as being free of UV radiation, the Wing LED modules are also free of infrared radiation in the beam. 16of17
Contacting Philips Selecon Philips Selecon 19-21 Kawana Street, Northcote, Auckland 1310, New Zealand Tel: +64-9-481 0100, Fax: +64-9-481 0101 www.seleconlight.com Philips Entertainment European Service & Distribution Centre Marssteden 152 Enschede 7547 TD the Netherlands Phone: +31 53 4500424 Fax: +31 53 4500425 Philips Strand Lighting USA Strand Lighting 10911 Petal Street Dallas, TX 75238 Tel: +1 214 647-7970 Support Main Fax: +1 214 647-8031 Strand Lighting Asia Limited 20/F Delta House 3 On Yiu Street Shatin, N.T. Hong Kong Tel: +(852) 2757 3033 Fax: +(852) 2757 176 Please contact us, or check our web site to find the Philips Selecon distributor nearest to you. www.seleconlight.com/distributors 17of17