Section 1: Screen Design 1.1 What is it for? SABLE FRAME 2 SERIES The Sable Frame 2 Series uses Elite s CineWhite tensioned 1.1 gain material within a velveteen coated frame. A new design feature for the CineWhite material is a rubber-edge border that makes installation a lot easier and a lot less time consuming. As an added bonus, a new installation kit with sliding wall brackets is included free of charge. 1.2 How does it work? The Sable Frame 2 Series is easy to assemble and installs in minutes. Its split-frame design facilitates lower shipping costs without sacrificing quality. Wall brackets allow the screen to slide horizontally to ensure properly centered installation. Section 2: Product Features 2.1 Characteristics Screen Material Award Winning CineWhite 1..1 Gain front projection material with black backing and full tension uniformity across entire viewing surface Outstanding picture quality at any viewing angle with no compromise in resolution or brightness Active 3D and 4K Ultra HD Ready Elegant velvet covered frame absorbs projector overshoot and increases picture contrast Assembles in minutes and includes installation hardware Design and Installation 2.4 width frame and is velvet coated Split-frame design facilitates lower shipping costs without sacrificing quality Easy to assemble and install in minutes Wall brackets allow screen to slide horizontally for properly centered installation Installation kit includes: Woods screws & anchors, Wall Brackets, Screwdriver, Mallet 1
2.2 Model Numbers Model Number Diag. Size Aspect Ratio Viewing Height (in) Viewing Width (in) Screen Material Gain Case Color N.W. (lbs) G.W. (lbs) Packaging Dimensions (LxWxH) ER92WH2 92" 16:9 45.1 ER100WH2 100" 16:9 49.0 ER106WH2 106" 16:9 52.0 ER110WH2 110" 16:9 53.9 ER120WH2 120" 16:9 58.8 ER135WH2 135" 16:9 66.1 ER150WH2 150" 16:9 73.6 ER165WH2 165" 16:9 80.9 ER180WH2 180" 16:9 88.2 ER200WH2 200" 16:9 98.0 ER109WX2 109" 16:10 57.5 ER114WX2 114" 16:10 60.0 ER115WH2-Wide 115" 2.35:1 45.0 ER125WH2-Wide 125" 2.35:1 48.9 ER138WH2-Wide 138" 2.35:1 54.0 ER158WH2-Wide 158" 2.35:1 61.9 80.2 CineWhite 1.1 Black 23.0 30.9 56.7"x6.7"x11.8" 87.2 CineWhite 1.1 Black 22.4 34.2 61.4"x6.7"x11.8" 92.4 CineWhite 1.1 Black 25.9 35.0 63.5"x6.7"x11.8" 95.9 CineWhite 1.1 Black 25.9 35.6 65.5"x6.7"x11.8" 104.6 CineWhite 1.1 Black 28.2 38.3 69.7"x6.7"x11.8" 117.7 CineWhite 1.1 Black 31.5 41.7 78.2"x5.7"x15.8" 130.7 CineWhite 1.1 Black 33.4 45.8 85.6"x5.7"x15.8" 143.8 CineWhite 1.1 Black 39.6 51.9 92.9"x5.7"x15.8" 156.9 CineWhite 1.1 Black 43.1 57.8 100.2"x7.7"x15.8" 174.4 CineWhite 1.1 Black 48.5 64.6 110"x7.5"x15.8" 92.0 CineWhite 1.1 Black 24.4 35.9 69.4"x6.7"x11.8" 96.0 CineWhite 1.1 Black 27.1 38.0 72.1"x6.7"x11.8" 105.8 CineWhite 1.1 Black 25.4 34.8 62.2"x6.7"x11.8" 115.0 CineWhite 1.1 Black 27.8 37.4 67.1"x5.5"x15.75" 127.0 CineWhite 1.1 Black 31.5 40.9 73"x5.5"x15.75" 145.4 CineWhite 1.1 Black 34.2 44.7 82.3"x5.7"x15.4" Section 3: Screen Material Specifications 3.1 Characteristics CineWhite (Tension Matte White) has broad light dispersion through diffusion uniformity, black & white contrast and true color rendition making it the most versatile in Elite's tensionss screen product lines. This tension PVC surface is the best choice for today's high-contrast ratio projectors in commercial or residential presentations. The CineWhite material equals the performance to our MaxWhite product, but improves the experience with the superior surface flatness. Uniform diffusion surface has black-backing to eliminate light penetration and is easily washable with mild soap and water. 2
Features & Benefits Multi-layer PVC (Polyvinyl chloride) with texture and surface coating Gain: 1.1 View Angle: 180 (90 ±LR) Full Lambertian Diffuser- no half gain drop Produces exceptional picture quality for any presentation Mildew Resistant Active 3D and 4K Ultra HD ready Surface can be cleaned with (water) moist cotton cloth Specifications Thickness Weight Maximum Height On-axis Gain Half-Gain Angle 0.27 mm 350 g/m2 3.2 M (10 ft) 1.1 Does not reach half gain 3.2 Gain and Viewing Angle Chart 3
Section 4: Execution 4.1 Care & Use Instructions Dust, dirt and scratches on the projection surface will affect the picture quality, please take note of the points below to prevent that from occurring: 1. Do not touch the projection surface with your hands 2. Do not write or draw on the projection surface 3. Do not use fingers or sharp objects to point on the projection surface; this willl damage the screen material. 4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning agents or alcohol. 5. Use clean water when dampening the cleaning cloth and do not rub against the material to clean it. 4.2 Hardware Parts List A. Frame Parts x 6 pcs (4 top/bottom frame pcs + 2 side frame pcs) B. Screen Material x 1 pc C. Center joints x 2 pcs D. Elbow Joints x4pcs E. Wall brackets x4pcs (depending on model/size) F. Wood Screws x 8pcs G. Drywall anchors x 8pcs H. M5x15 screws x 16 pcs I. Center Support Bar x 1-2 pcs (depending on model/size) J. Support joiner x 2-4 pcs (depending on model/size) K. Fix Plates x 60-180 pcs (depending on model/size) L. Rubber hammer x 1 pc M. Screw driver x 1 pc Note: Please make sure all parts are included in your package before proceeding to assemble your fixed frame projection screen. 4
4.3 Frame Assembly 1. Insert the center joint (c) connector to the ½ horizontal frame piece and fasten it with two M5x15screws (h). M5 15 Screw ½ Long Frame bevel 2.Insertthe other ½ horizontal frame piece to the center joint (c) connector and fasten it with two M5x15 screws (h).repeat steps 1 and 2 for assembling the second horizontal frame. M5x15 ½ Long Frame Pus Bevel Horizontal Long Note: a. Two½ size horizontal frames should be assembled for a screen. b. Do not tighten the screws completely until all frame pieces have been assembled correctly. 3. Insert both elbow joint (d) connectors into the long horizontal frame and fasten it with twom5x15 screws (h) seefig.1. Then insert the vertical short frames into the exposed elbow joint (d)connectors and fasten them with M5x15 screws(fig.1.2). 5
Long frame Push Push M5x15 screws Joint M5x15 screws Screw (Fig.1.1) ( fig.1) Push Short frame Push M5x15Screws Short frame (Fig.1.2) 4. Join all four frame parts together following the steps shown below. (Fig.2) Note: When assembled, please push simultaneously the two ends of the long frames. Insert the exposed ends of the joint connectors into the short (vertical) frame and align the four corners so that they meet at perfect right angles Push Push Elite Scree creens Taiwan Corp Elite Screens Japan Elite Screens Australia M5 15 screws 6
Screw ( fig.2) 4.4 Attaching the screen material to the frame 1. Make sure the screen material al and frame are both lying face down on a clean, dry, and non-abrasive surface. 2. Carefully unroll the material inside the frame. (Fig.3) Please note the material will be noticeably smaller than the frame, as the material must be stretched to create a sufficient amount of tension for perfect material flatness. (Fig.3) Notes: Make note of the label to help distinguish the back and front side. Unroll the screen material face down Keep the screen material as close as possible to the frame and do not allow it to scratch against any part of 3. Attach the fix plates. (1) Stretch the material to the corner and insert the screen material s edge in the groove of the frame. While one hand holds the material in place the other hand snaps in the push plate (Fig.4-Fig.5). (Fig. 4) Plate Insert push plate in (Fig. 5) Schematic cross section of the frame Frame groove Screen material edge 7
(2) Begin by securing the four corners in the following sequence A B C D (Fig.6). (3) Insert the fix the plates as shown on Fig. 5. Fix plate 1 is about 10cm away from the frame s corner. Fix plate 2 is about 5cm away. (Fig.7) C A (Fig. 7) B (Fig. 6) D Tip for attaching the last corner (D): 1. Position yourself left of location 1. 2. Pull the material to the corner of the frame with your hand while your left hand snaps in the fix plate on location 1(the third red dot). Pull 3 4 3. Then insert and snap in the fix plate on location2. 4. Next, moveand position yourself on location 3,then pull the edge to the frame and fasten plates on locations3and4. 1 2 5 (Fig. 8) (4) Place a fix plate in the center of each side in the following ordere F G H.(Fig.9) E H G (5) Next, fasten a fix plate on the center of each frame side in the following order I J K L M N O P as shown in Fig.10. 8 F ( Fig.9)
I P J O K N (Fig.10) L M (6) Fasten the remainder of the fix plates in the empty locations in the red markings to complete attaching the screen material. (Fig.11) (Fig.11) Black backing for AcousticPro models This procedure only applies to AcousticPro models. Disregard this section if your Fixed Frame does not include an acoustically transparent screen material. The purpose of the black backing material is to block out any light penetration that may reflect off of anything mounted behind the screen, which can cause distortion to the projected image. The black backing is held in place by the Velcro that is on the fix plates. 9
http://www. www.elitescreens.com PRODUCT WHITE PAPER Black backing Fix plates secure the Acoustic material and the black backing behind it. Interval markings reveal the best points for inserting the fix plates (Fig. 12). The prongs on the fix plates insert to the lip on the back of the frame creating a friction hold that will firmly keep the material and black backing in place (Fig. 13-14).After 14).After the material has been installed, the backing will lay over the back of the white (Acoustic) material and then be held in place by the Velcro on the fix plates(fig 15). (Fig. 13) (Fig. 12) (Fig. 14) (Fig. 15) 4.5 Center Support Bar 1. Insert the support joiner (j) into each end of the center support bar (i). support joiner 2. Center support bar Insert the Center Support Bar into the upper top groove on the back of the frame (not the one where the fix plate inserts) with the bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of the bar are in alignment with the groove (see Fig. 16and Fig. 17below for details). Diagonal models ls 135 and below use 1 x Center Support Bar Remove push Fixed plate groove Center Support Bar (do not insert here) (Fig. 16) Screen material Elite Screens Inc. Ellite Screens Europe GmbH Elite Screens India Elite Screens China Ltd. Elite Screens creens Taiwan Corp Elite Screens Japan Elite Screens Australia 10
Diagonal models above 135 requiree 2x Center Support Bars (Fig. 17) 3. Slide the top end of the bar into the top center point of the frame to complete the center support bar installation. This will provide added stability to your frame and added tension to the material. 4.6 Installation 1. Locate your desired installationn location with a stud finder (recommended) and mark the drill-hole area of where the screen is to be installed. 2. Drill a hole with the proper bit size according to the wood screws included. 3. Line up the wall brackets with the drilled holes on the installation location and screw them in using a Phillips screwdriver. Note: Use 2 top wall brackets on diagonal sizes below 135, and use 3 top wall brackets on diagonal sizes 135 and above. 4. Position the fixed frame screen onto the top wall brackets as shown in (Fig. 18) and push down at the center of the bottom frame to secure the installation. 5. The design of the wall brackets allows the frame to slide over them through its sides. This is an important feature of the installation design as it allows your screen to be properly centered. 6. Using both hands finish the installation by pushing the lower portion of the fixed frame screen into the lower bracket as shown in Fig 19. 11
(Fig. 18) (Fig.19) CAUTION Please follow these instructions carefully to ensure proper maintenance and safety of your Fixed Frame Screen. 1. When hanging the screen up, please make sure that no other objects such as power switches, outlets, furniture, ladders, windows, etc. occupy the space designated for your Fixed-Frame screen. 2. Regardless if the screen is hung on or installed into the wall, make sure that the proper mounting anchors are used and that the weight is supported appropriately by a strong and structurally sound surface just as any large and heavy picture frame should. (Please consult a home improvement specialist for the best advice on installation) 3. Frame parts are made of high quality velour-surfaced aluminum and should be handled with care. 4. When not in use, cover over the screen with a furniture sheet to protect it from dirt, grime, paint or any other impurities. 5. When cleaning, use a damp soft cloth with warm water to remove any marks on the frame or screen surface. 6. Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface. 7. In order to avoid damaging the screen, avoid touching it directly with your fingers, tools or any other sharp or abrasive objects. 8. Spare Parts should be placed out of reach of small children in accordance with household safety guidelines. 12
Section 5: Product Specifications 5.1 Dimensions Model Number Diag. Size Aspect Ratio Viewing Width (A) Overall Width (A1) Viewing Height (B) Overall Height (B1) Frame Width (C) Frame Depth(D) Unit: Inches ER92WH2 92" 16:9 80.2 84.9 45.1 49.8 2.4 1.6 ER100WH2 100" 16:9 87.2 91.9 49.0 53.7 2.4 1.6 ER106WH2 106" 16:9 92.4 97.1 52.0 56.7 2.4 1.6 ER110WH2 110" 16:9 95.9 100.6 53.9 58.7 2.4 1.6 ER120WH2 120" 16:9 104.6 109.3 58.8 63.5 2.4 1.6 ER135WH2 135" 16:9 117.7 122.4 66.1 70.9 2.4 1.6 ER150WH2 150" 16:9 130.7 135.4 73.6 78.3 2.4 1.6 ER165WH2 165" 16:9 143.8 148.5 80.9 85.6 2.4 1.6 ER180WH2 180" 16:9 156.9 161.6 88.2 92.9 2.4 1.6 ER200WH2 200" 16:9 174.4 179.1 98.0 102.8 2.4 1.6 ER109WX2 109" 16:10 92.0 96.7 57.5 62.2 2.4 1.6 ER114WX2 114" 16:10 96.0 100.7 60.0 64.7 2.4 1.6 ER115WH2-Wide 115" 2.35:1 105.8 110.6 45.0 49.8 2.4 1.6 ER125WH2-Wide 125" 2.35:1 115.0 119.7 48.9 53.7 2.4 1.6 ER138WH2-Wide 138" 2.35:1 127.0 131.7 54.0 58.7 2.4 1.6 ER158WH2-Wide 158" 2.35:1 145.4 150.1 61.9 66.6 2.4 1.6 Unit: mm ER92WH2 92" 16:9 ER100WH2 100" 16:9 ER106WH2 106" 16:9 ER110WH2 110" 16:9 ER120WH2 120" 16:9 ER135WH2 135" 16:9 ER150WH2 150" 16:9 ER165WH2 165" 16:9 ER180WH2 180" 16:9 ER200WH2 200" 16:9 ER109WX2 109" 16:10 2037 2156 1146 1265 2215 2334 1245 1364 2347 2466 1321 1440 2436 2555 1369 1491 2657 2776 1494 1613 2990 3109 1679 1801 3320 3439 1869 1989 3653 3773 2055 2175 3985 4105 2240 2360 4430 4549 2489 2611 2337 2456 1461 1580 60 40 13
Model Number Diag. Aspect Viewing Overall Viewing Overall Size Ratio Width (A) Width (A1) Height (B) Height (B1) ER114WX2 114" 16:10 2438 2558 1524 1643 ER115WH2-Wide 115" 2.35:1 2687 2809 1143 1265 ER125WH2-Wide 125" 2.35:1 2921 3040 1242 1364 ER138WH2-Wide 138" 2.35:1 3226 3345 1372 1491 ER158WH2-Wide 158" 2.35:1 3693 3813 1571 1691 Frame Frame Width Depth(D) (C) 5.2 Drawings 14
5.3 Pictures Frame Detail Back View and Detail 15
Sable Frame 2 Series Aspect Ratios Sizes in 16:9 Aspect Ratio 16
Installation Kit Life Style 17
Section 6: About Elite Screens 6.1 Company Description Elite Screens Inc. is a California based company that specializes in making quality commercial and home-theater projection screens for the retail and custom install sales channels. Our company began as an innovative venture into the projection market by manufacturing veterans from the AV/IT industry. Elite Screens quickly established itself as an entry level commercial and home theater screen manufacturer. This was accomplished by making a quality product cost effective with a focus on mass-producing screen material, sizes and aspect ratios that weree most commonly preferred by AV customers in general. We focused on uniformity with what would match the mainstream demographic while ncluding extra features that are not usually included by other manufacturers. In time, we progressed from just retail sales into the realm of custom installer/integrator manufacture as our numerous reviews and awards will attest. We stand behind our product and are so certain of customer satisfaction with the quality of our product that we offer a 2-year manufacturer's warranty which is twice the industry standard. In our continued devotion to excellence in products and service, we are committed to implementing green practices with our production. We have adopted manufacturing methods that promote conservative regulation of our energy needs. Our simple product designs combined with the expertise of our permanent staff ensures that our entire line of products are made by experienced hands devoted to the high standards of today s audio-video consumer. ### 18