DVD Player DV2X708DU
Contents Features...2 For your Attention...3 Accessories...4 Panel...5 Connections...6-7 System Setup...8-11 Remote Control...12-13 Playback...14-18 Troubleshooting...19 Specifications...Back Cover -1-
Features Thanks for your purchase of our product. Please read through this manual before making connections and operating this product. Retain this manual for future reference. DVD player is a domestic video player of new generation which produces high quality pictures and Hi-Fi audio effect. Its performance is much better than that of any previous home video equipment. As the best signal source, it will give you the uppermost enjoyment! MPEG4, PCM etc. digital audio decoder. Hi-fi, 96kHz/24bit audio digital processor. Software intelligent upgrade. High-resolution component video output, support the future video equipment. Coaxial digital audio output. Compatible with DVD/DVD-R/DVD+R/DVD-RW/DVD+RW/SVCD/ VCD/DVCD /CD/CD-R/MP3/MPEG4/ KODAK PICTURE CD etc. High integrated servo system, decoding on single-chip technology, high reliability and stability, and super error- correction. -2-
IMPORTANT NOTES For Your Attention Please read through this manual before making connections and operating this product. Retain this manual for future reference. Don't open the cabinet of this unit. No user-serviceable parts inside. Refer servicing to qualified personnel only. Switch off the unit when you don't use it. Switch off the unit and disconnect it from the AC power supply when it is not being used for a long time. (Plug, as the disconnected device entirely with power source, should keep in easy-to-operation in daily life.) Don't install the unit in a place exposed to heating sources or direct sunshine. Don't install the unit in a place exposed to moisture or rain. The apparatus shall not be exposed to dripping or splashing and any object filled with liquids, such as vases shall not be placed on it. Install the unit on a horizontal, flat and firm surface with good ventilation. Never block the vents which will cause malfunction resulted from overheating. Use a soft and clean rag to clean the outside of the unit. Never clean it with chemicals or detergent. This book is only a guide for user's operation, not a criterion for configuration. The lightning flash is intended to alert the user to the presence of dangerous voltage within the product's enclosure, and touching the internal components may result in a risk of electric shock to persons. The exclamatory mark is intended to alert the user to the presence of important operating instructions. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CLASS 1 LASER PRODUCT To reduce the risk of electric shock or fire, do not open the cover. Refer servicing to qualified service personnel. This mark indicates this unit belongs to class 1 laser product. The laser beam may produce radiation harm to the directly touching human body. -3-
Accessories Accessories User manual User manual Remote control OPEN/CLOSE Çú Çú A/V cable SUBTITLE MENU ÉùµÀ L/R/ST STANDBY ìíë TITLE AUDIO VIRTUAL PROG A-B ZOOM OSD + USB 5 6 _ VOL Ñ Ê± ENTER È ÈÏ 2 8 10+ 3 9 ì½ø GOTO V-MODE STEP ANGLE REPEAT RESET SLOW 1 4 7 0/10 0 DV2X708DU Playable Disc and Media Types: Disc types Symbol Contents DVD Audio + Video MP3 Audio Video-CD VCD COMPACT DIGITAL VIDEO VIDEO CD Audio + Video CD-DA Audio Picture CD JPEG Photo CD Kodak Picture CD Electronic Photo MPEG-4 V I D E O Audio + Video -4-
MIX L Panel Front panel 4 5 6 7 STANDBY USB 1 2 3 1. DISC DOOR 2. DISPLAY SCREEN 3. USB INTERFACE 4. STANDBY BUTTON 5. OPEN/CLOSE 6. STOP 7. PLAY/PAUSE Rear panel 1 2 SCART Y U/Pb V/Pr VIDEO MIX R COAXIAL S-VIDEO 3 4 5 6 1. COMPONENT VIDEO OUTPUT 2. COMPOSITE VIDEO OUTPUT 3. MIX L/R AUDIO OUTPUT 4. COAXIAL AUDIO OUTPUT 5. S-VIDEO OUTPUT 6. SCART OUTPUT -5-
Connections Video System Connection There are four types of video outputs available for this unit. TV/Monitor Video Input Component Input Y U/Pb V/Pr S-VIDEO VIDEO SCART Input Composite Video Use the cable with yellow plug of an AV cable to connect the composite video output of this unit to the video input of a TV/monitor. Component video(yuv) Use a 3-core AV cable to connect the component outputs of this unit to the corresponding inputs of a TV/monitor. S-Video Use a S-Video cable to connect the S-Video output of this unit to the S-video input of a TV/monitor. SCART Use a 21_pin SCART cable to connect the SCART output of this unit to the TV/monitor SCART input. Y U/Pb V/Pr Component Video Output VIDEO S-VIDEO Video and S-Video Output DVD Player Video Output SCART Output Notes: Which connection you should make depends on the TV/monitor input terminals. Don't make all the connections above at the same time, otherwise the produced pictures will be affected. Only when the video setting conforms to the practical video system connection can the unit produce the normal pictures. (Please refer to the Video Setup in System Setup). -6-
Connections Audio System Connection There two types of audio output systems. They are analog audio output system and digital audio output system. Analog audio output system includes 2-channel stereo output. Digital audio output system includes coaxial output. TV/Monitor/Amplifer Audio Input 2CH Audio Input Digital Audio Input COAXIAL L R Stereo Audio Use a pair of audio cable (white for left, red for right) to connect the stereo audio outputs of this unit to the stereo inputs of a TV or a power amplifier. Coaxial Audio Use a coaxial cable to connect the coaxial output of this unit to the coaxial input of a power amplifier. Note: The audio setting should conform to the practical audio system connection. Please refer to the Audio Setup in System Setup. MIX L MIX R 2CH Audio Output COAXIAL Digital Audio Output DVD Audio Output -7-
System Setup Menu Operation 1. Press [SETUP] on the remote control to show the SETUP MENU. 2. Press [ ]/[ ] to select GENERAL SETUP PAGE, AUDIO SETUP PAGE, DOLBY DIGITAL SETUP, VIDEO SETUP PAGE or PREFERENCE PAGE. The submenu of the selected item will be listed below instantly. 3. Press [ ]/[ ] to move the highlight in the submenu to select an item you desire to set, then press [Enter]/[ ] to enter. Use [ ]/[ ] to select an option, then press [ENTER] to confirm it, or press [ ] to cancel. 4. Then you can press [ ]/[ ] to continue to set other items in the submenu. 5. Press [ ] to go back to the parental menu of the current one. 6. Press [SETUP] again to exit SETUP MENU. 1 GENERAL SETUP PAGE There are five items in the submenu. They are TV DISPLAY, ANGLE MARK, OSD LANGUAGE, CLOSED CAPTIONS, SCREEN SAVER. 1.1 TV Display: 4:3 PAN SCAN: When the unit is connected to a normal TV set, the wide-screen image will be shown on the screen in proportion with some part on the left and right cut off. 4:3 LETTERBOX: When the unit is connected to a normal TV set, the wide-screen image will be completely shown on the screen in proportion with two black bars on the top side and bottom side. 16:9: When the unit is connected to a wide-screen TV set, select this option. The wide-screen image will be completely shown on the screen in proportion. 1.2 ANGLE MARK: Set this item to ON. When the disc with multiple camera angles is playing, an angle mark will displayed on the screen. Then you can view the video of different camera angles by pressing [ANGLE] on the remote control. Set this item to OFF to hide the angle mark. 1.3 OSD (On Screen Dislay) LANGUAGE: You can select an OSD language in this item. -8-
System Setup 1.4 CLOSED CAPTIONS: Some discs have closed captions. Set this item to ON to show the closed captions if the playing disc has closed captions. Set this item to OFF to hide closed captions. You can also press [SUBTITLE] on the remote control to show/hide the closed captions. 1.5 SCREEN SAVER: ON: When the player stops or the picture becomes motionless for some time, there will be a screen saver to prevent damage to the display screen. Press [STANDBY] either on the remote control or on the main unit to switch off the unit. OFF: Disable the screen saver function. 2 AUDIO SETUP PAGE There are two items in the submenu. They are ANALOG AUDIO SETUP, DIGITAL AUDIO SETUP. 2.1 ANALOG AUDIO SETUP 2.1.1 DOWNMIX LT/RT: When you play the 5.1-CH disc, the audio is mixed into left channel and right channel. STEREO: When you play the 5.1-CH disc, the audio is mixed into stereo channel. 2.2. DIGITAL AUDIO SETUP 2.2.1 DIGITAL OUTPUT: SPDIF OFF: There will be no digital audio signal output. (Coaxial off) ALL: The digital audio signal output will be in RAW format. PCM ONLY: The digital audio signal output will be in PCM format. 3 DOLBY DIGITAL SETUP 3.1 DOLBY DIGITAL SETUP 3.1.1 DUAL MONO Stereo: Set audio output to the stereo output. L-mono: Set audio output to the mono-left channel. -9-
System Setup R-mono: Set audio output to the mono-right channel. Mix-mono: Set audio output to the Mix mono channel. 3.1.2 DYNAMIC When you watch films with large dynamic scope in low volume, for example at night, you can adjust the dynamic value up to avoid losing sound details resulted from the low volume. 4 VIDEO SETUP PAGE 4.1 VIDEO OUTPUT: OFF: Set video output to the composite. YUV: Set video output in analog component video format when connecting to the Y/U/V terminals. P_YUV: Set video output as progressive YUV signals. Connection is the same as YUV. RGB: Set video output in Red/Green/Blue format when connecting to the SCART terminal. P_RGB: Set video output as progressive RGB signals. Connection is the same as RGB. Note: If the video setting differs from the physical video connection, the TV set may have no picture. You can also press [V-mode] on the remote controller to switch the video output mode. 4.2 SHARPNESS There are three options (HIGH, MEDIUM and LOW) for you to choose in this item. 4.3 BRIGHTNESS and CONTRAST Enter the two items respectively, then use direction key [Left]/[Right] to adjust the value, then press [ENTER] to confirm it. 5. PREFERENCE SETUP This item is available only when there s no disc in the disc tray or the disc tray is open. There eight items in this item. They are TV TYPE, AUDIO, SUBTITLE, DISC MENU, PARENTAL, PASSWORD, DEFAULT and SHADOW TO FLASH. -10-
System Setup 5.1 TV TYPE This product supports both NTSC(National Television System Committee) and PAL (Phase Alternating Line) television broadcasting standards. PAL : This is used in China, Hongkong and Europe etc. MULTI: When this option is selected, the uni t will detect the standard automatically. NTSC: This is used in Taiwan, America and Canada etc. Note: If a wrong selection is made, the viewing image will be very poor. In such case, you are supposed to change the option in this item to fix the error. 5.2 AUDIO, SUBTITLE and DISC MENU Select a(n) audio/subtitle/ disc menu language by your preference. You can also make these selections by pressing [Audio]/[Subtitle] on the remote controller. Note: If the selected language is not available for the disc currently being played, the disc language setting works. default audio/subtitle 5.3 PARENTAL This item allows the user to set a maximum rating of the movies that can be viewed. Movies rated higher than the level set for the parental lock can not be viewed. And, to key in the correct password is needed to reset the level. The initial factory password is 136900. Note: The parental function needs support of the playing disc. 5.4 PASSWORD You can reset the password in this item. Note: The initial factory password(136900) works at any time. So if you forget the password you set, you can use it. 5.5 DEFAULT Resume to the initial factory settings. 5.6 SHADOW TO FLASH Save your settings. -11-
Remote control Remote Control Operation Install the batteries into the remote control. Point the remote control at the remote sensor on the front panel. The remote control works within about 8 metres from the sensor and within an angle of about 30 degrees from the left and right side. Take out of the batteries when it is not being used for a long time. Don't expose the sensor in direct sunlight. Battery Installation 1 Remove the battery compartment cover on the back of the remote control. 2 Insert two AAA/1.5V batteries 3 into the battery compartment following the indications (+, -) inside the compartment. Replace the cover. Not e: Don not mix the old and new batteries or different types of batteries. Weak batteries can leak and severely damage the remote control. -12-
Remote control 1 2 3 4 5 6 7 8 9 10 11 12 13 14 STANDBY 1 4 7 0/10 0 2 5 6 8 10+ ìíë ì½ø TITLE AUDIO PBC PROG ANGLE REPEAT SLOW 3 9 Ñ Ê± GOTO ENTER È ÈÏ OPEN/CLOSE A-B OSD Çú Çú V-MODE STEP RESET + _ VOL SUBTITLE MENU ÉùµÀ L/R/ST USB ZOOM 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 1 STANDBY 2 DIGIT KEYS 3 FAST FORWARD FAST REWIND 4 PLAY 5 STOP 6 TITLE 7 DIRECTION KEYS 8 AUDIO 9 ANGLE 10 PBC 11 REPEAT 12 PROGRAM 13 MUTE 14 SLOW 15 SETUP 16 OPEN/CLOSE 17 A-B REPEAT 18 OSD 19 VOLUME+/- 20 GOTO 21 NEXT/PREV 22 PAUSE 23 SUBTITLE 24 ENTER 25 MENU 26 V-MODE 27 L/R/ST 28 STEP 29 USB 30 ZOOM 31 RESET DV2X708DU -13-
Playback After all the connections have been made correctly, the unit is ready for service. 1. Switch on the TV and select AV mode. Select S-video if you made S-Video connection. 2. Switch on the power amplifier if the unit's connected to it. Select AC-3 or DVD mode. 3. Switch on the DVD player. The unit will automatically load the disc if there it is in the disc tray and will show 'No Disc' on the screen if there isn't any. STANDBY Switch on the unit. /Put the unit in standby mode. Note: Being in the standby mode uses a minimal amount of electricity, but ensures that the components of the unit operate at maximum efficiency from the moment you start. OPEN/CLOSE Open or close the disc tray. 1 4 2 3 5 6 7 8 9 0/10 10+ Use the digit keys to input the corresponding numbers. When playing VCD1.1, CD, mp3 disc etc., after loading the disc, use the digit key to select the desired folder, track or file directly. DIRECTION KEYS You can use the direction keys to move the highlight in the menu. GOTO ENTER If the a VCD is currently playing, press this button show the GOTO menu. You can use digit keys to input the Track, Disc Time and Track Time from which the unit will skip to play. Press this button again to exit it. If the a DVD is currently playing, press this button select a chapter to play. Press this button to enter an item or confirm your operation etc. Press this button to pause the playing disc. Press [ ]or [ ] to continue. -14-
Playback Press this button to play the disc if it is not in normal playing status. Press this button for fast forward playback. Press this button for fast reverse playback. When a disc is currently playing, press this button to pause it and press [ ] to resume playing from the position where you stopped playback; press this button twice to stop the disc and the disc is reset to the start. Skip to the previous chapter/track. Skip to the next chapter/track. VOLUME TITLE SUBTITLE Press VOLUME +/- to adjust the volume. When a DVD is currently playing, press this button to return to the title menu. If the playing disc has multi subtitles, you can select a subtitle language by pressing this button. AUDIO If the playing disc has multi sound tracks or multi languages, you can select an audio language by pressing this button. -15-
Playback MENU When a DVD is currently playing, press this button to return to the main menu. It works as [PBC] for VCD2.0 disc and SVCD, etc. Press it to show or hide the PBC menu. ANGLE V-MODE Some discs include scenes recorded in multiple camera angles. Press this button switch the camera angle. Press this button to switch the video output modes. SLOW Press this button for slow-motion playback. Press [ ] to resume to normal playback. RESET STEP ZOOM REPEAT When the disc tray is open, press this button to resume the default settings. When a DVD, MPEG4 or VCD disc is currently playing, you can view the video frame by frame by pressing this button. Press [ ] to exit. When a DVD, SVCD, MPEG4 or VCD disc is currently playing, press [ZOOM] to zoom in/out the scene. When the scene is zoomed in, you can use the direction keys to move the scene. When a DVD disc is currently playing, press this button continually to switch between CHAPTER, TITLE and ALL. When a MP3/CD disc is currently playing, press this button continually to switch between SINGLE, REPEAT ONE, REPEAT FOLDER and FOLDER. When a VCD disc is currently playing, press this button continually to switch between TRACK and ALL. -16-
Playback A-B You can repeat a specific section of a disc. When a DVD or CD disc is currently playing, press this button to mark down the starting point (A) and press it again to mark down the ending point (B). Then, the unit will playback this section over and over again. Press it for the third time to cancel repeat. SETUP Press the button to display the system setup menu, and press it again to exit. MUTE Press this button to switch off the sound temporarily. Press it again to switch it on. OSD Press the this button to show the relative information of the playing disc. USB PROGRAM Insert a U-disc into the USB interface, then press this button to play the files in it. Press it again to exit. Press this button the display the program menu. Press it again to exit. L/R/ST PBC When playing VCD or CD disc with multi-channel, press this button to select left channel/right channel/stereo/mix audio output. When a VCD2.0 disc is currently playing, press this button to show/hide the PBC menu. Note: VCD1.1, CD-DA and M P3 disc have no PBC menu. -17-
Playback PICTURE CD PLAYBACK Place a Picture CD in the disc tray, then a menu will be displayed on the screen showing the contents in the disc. Use the direction keys to move the highlight on a photo file, then press [ ]/[ENTER] to play the picture CD. When a picture CD is playing, you can Press [ ]/[ ] to skip to the next/previous photo; press [ ] to pause the disc. when a picture CD is currently playing, press [MENU] to return to the previous menu. When a picture CD is playing, you can use the direction keys to rotate the photo. MP3/MPEG4 PLAYBACK Place a MP3/MPEG4 disc in the disc tray, then a menu will be displayed on the screen showing the contents in the disc. Use the direction keys to move the highlight on a folder or track/file, then press [ENTER] to play the selected folder or track. You can also use the digit keys on the remote controller to implement this operation. For example, press '0' and '1', then press [Enter] to play the first track/file or folder. Note: For some discs, select a folder and press [ENTER] or select the folder with the digit keys is to enter the corresponding folder instead of to play the folder. When the disc is playing, press [ ]/[ ] to skip to the next/previous track/file; press [ ]/[ ] for fast forward/reverse; press [ ]/[ ] to pause/play the disc; press [ ] to pause the disc; press it twice to stop the disc. press direction key [ ] to return to the previous menu. U-Drive Playback: Insert a U-drive into the USB interface on the front panel. The unit will automatically play the readable files, for example MP3 and MPEG4, in it. (If a disc is currently playing, you need to press [USB] and select USB to play the U-drive.) -18-
Troubleshooting No power No sound Symptom No picture Distorted picture Luminance unsteady or picture with noise Unable to play Key malfunction Remote controller doesn't work Cause(s) The power cord isn't connected TV video setup isn't corrected The setup mismatch the real connection Video cable isn't connected well Audio cable isn't connected well Power off for the connected equipment Audio setup isn't corrected Dirty disc In fast forward or fast rewind mode Anti-copy circuit influence Without disc Disc is bad Disc is put upside down Dirty disc There are menu on TV screen Parental control is working Power wave or other static interference. Remote controller isn't pointed at the sensor. Remote controller is too far from DVD unit Batteries are exhausted. Remedy Connect the power cord properly Select the suitable setup Press [V-MODE] until the picture appears again Connect the cable properly Connect the cable properly Turn on power Select the suitable audio setup Clean the disc Sometimes, the tiny distortion appears. It's normal Connect the DVD unit to TV directly Put in the disc Clean or replace the disc Put the disc properly Clean the disc Use SETUP to turn off menu Set up parental off or change the setup Turn on/off the power and try again. Point the remote controller at the sensor Operate the remote controller within 8m Replace the batteries -19-
Specifications Power supply Power consumption TV system Laser wave length Audio frequency range S/N ratio Audio dynamic range Operating conditions Video output S-video output Audio output (analog audio) AC~100-240V/50/60Hz 20W PAL /NTSC 650nm, 780nm DVD: 4Hz~22kHz 48kHz PCM 4Hz~ 44kHz 96kHz PCM CD: 4Hz~20kHz 90dB 90dB Temperature: 0~40, operation flat, horizontal 1.0V P-P 75 Y 1.0V(P-P),75 C 0.286V(P-P),75 2.0V(rms) -20-