PRODUCT DATASHEET series last update 20/12/2016 FCN15302_RONDA-WW 19.8 mm ["socket", "screw"] FCN15303_RONDA-WWW 19.8 mm ["screw", "socket"] FCN15314_RONDA-WAS 25.42 mm FCN15315_RONDA-WW 19.8 mm (simulated) 62 (simulated) 89 % (simulated) 90 (simulated) 87 % (simulated) Asymmetric (simulated) 86 % Developed especially for wall washing applications at ~1:3 ratio assembly setup. (simulated) 62 (simulated) 89 % August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 1/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FCN15316_RONDA-WWW 19.8 mm FCN15357_RONDA-ZT45 20.66 mm FCN15366_RONDA-ZT45 20.66 mm FCN15499_RONDA-W 19.8 mm (simulated) 90 (simulated) 87 % (simulated) Asymmetric (simulated) 87 % Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height). (simulated) Asymmetric (simulated) 87 % Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height). (simulated) 42 88 % August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 2/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FCN15621_RONDA-W 19.8 mm FN15731_RONDA-WAS-B 22.3 mm Sample approved FN15733_RONDA-ZT45-B 15.4 mm Sample approved FN15734_RONDA-S-B (simulated) 42 88 % (simulated) Asymmetric (simulated) 86 % (simulated) 1.100 BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr compatible Developed especially for wall washing applications at ~1:3 ratio assembly setup. (simulated) Asymmetric (simulated) 87 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height) (simulated) 24 (simulated) 85 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 3/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FN15735_RONDA-W-B Sample approved FN15736_RONDA-WW-B Sample approved FN15737_RONDA-WWW-B Sample approved FN15738_RONDA-REC-60-B (simulated) 42 (simulated) 88 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible (simulated) 62 (simulated) 89 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible (simulated) 90 87 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible (simulated) 62+62 (simulated) 90 % BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr (50-20, 50-30) compatible August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 4/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FCN15740_RONDA-REC-60 Pack Clear Sample approved FCN15209_RONDA-WAS 25.42 mm ["snaps", "socket", "screw"] FN15380_RONDA-WAS 22.3 mm FN15380_RONDA-WAS 22.3 mm (simulated) 62+62 (simulated) 89 % Asymmetric degrees 91 % 0.950 Developed especially for wall washing applications at ~1:3 ratio assembly setup. "clips", Asymmetric degrees 91 % 0.950 Developed especially for wall washing applications at ~1:3 ratio assembly setup. (simulated) 86 % Developed especially for wall washing applications at ~1:3 ratio assembly setup. August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 5/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FN15381_RONDA-WWW FN15381_RONDA-WWW FN15387_RONDA-WW FN15387_RONDA-WW (simulated) 87 % (simulated) 87 % (simulated) 89 % (simulated) 89 % August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 6/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FN15388_RONDA-ZT45 15.4 mm FN15388_RONDA-ZT45 15.4 mm FN15388_RONDA-ZT45 15.4 mm FN15552_RONDA-W (simulated) 87 % Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height). (simulated) 87 % Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height). 88 % Double asymmetric beam. Developed especially for wall washing, corridor and supermarket applications @ ~1:2 ratio aisle assemblies (aisle width = wall height). 88 % August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 7/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FN15622_RONDA-REC-60 Pack Clear FN15679_RONDA-S ["screw"] FN15679_RONDA-S ["screw"] FN15977_RONDA-WAS2 (simulated) 89 % (simulated) Asymmetric (simulated) 86 % (simulated) 1.100 Developed especially for wall washing applications at ~1:3 ratio assembly setup. August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 8/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FN15993_RONDA-O 17.28 mm FN15997_RONDA-O-B 22.3 mm FN15998_RONDA-O-C Clear 53.9 mm 16.6 mm FN15552_RONDA-W (simulated) 49+21 (simulated) 2.140 (simulated) Asymmetric (simulated) 0.000 BJB 47.319.2xxx 50mm / Stucchi 8xxx/G2 50mm / Ideal chip lok jr compatible (simulated) Asymmetric (simulated) 0.000 63 degrees 91 % 0.750 August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 9/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 FCN15739_RONDA-REC-60 Pack Clear Sample approved FN15789_RONDA-REC-90 Pack Clear FCN15790_RONDA-REC-90 Pack Clear 19.8 mm Sample approved 63 degrees 91 % 0.750 87 degrees 91 % 0.500 Developed especially for office applications. 87 degrees 91 % 0.500 Developed especially for office applications. NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 10/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
PRODUCT DATASHEET series last update 20/12/2016 GENERAL INFORMATION - Product series especially designed & optimized for series of s. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade with high UV and temperature resistance. Allows use of high current and temperature conditions. Please find more information about used material from below: http://ledil.fi/sites/default/files/documents/technical/material/%208n%20ul94_yellow%20card.pdf http://ledil.fi/sites/default/files/documents/technical/material/%208n%20plexiglas-datasheet.pdf Note! Due to use of high power COB's with this product, special attention to proper thermal design is highly recommended. il has no liability for direct, indirect or consecutive damages arising from the il products being used outside of the recommended temperature range. August 10th 2017 16:01 Copyright - Subject to change without prior notice - Page 11/11 24240 SALO http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001
A B C D E F G H 4 4 Front plate examples Examples 3 D=49.9 Optic D=69.9mm 2 Ledil-clamp / TE / Bender-wirth / other twist and lock socket types (holder A) 3 Rotation fix Horizontal fix: M3 Nut + bolt Vertical fix: M3 Screw / Twist and lock / Snap 2 BJB and Stucchi 50mm (holder B) LES size up to ~14mm, see compatibility www.ledil.com Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 This drawing is the property of il Oy. It may not be reproduced, copied or communicated without a written agreement with il Oy. See more details on page 2 and 3 H G FIN 24240 SALO DRAWING TITLE RONDA-family SIZE A3 SCALE 1 PART NUMBER 1:1 WEIGHT - B SHEET A 1/3
A B C D E F G H A 4 3.5 6 4 ( 64.1 ) Front panel location suggestion when seamless look needed Bottom view Nut slot Isometric view 14.6 4 3 7.7 59.3 3 2.2 ronda-was Detail A 12.7 11.2 Front view 45 53. c ti 49.9 2 61 ( Socket op 2 2.4 * 8.9.8.9 69 er d l ho ) 3 3.2 Top view * Ensure from 3d according specific optic version Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 3. 2 3. 2 This drawing is the property of il Oy. It may not be reproduced, copied or communicated without a written agreement with il Oy. FIN 24240 SALO DRAWING TITLE RONDA-family SIZE A3 SCALE H G 1 PART NUMBER 1:1 WEIGHT - B SHEET A 2/3
A B C D E F G H 4 OPTIC/HOLDER ASSEMBLY TYPICAL CONNECTOR ASSEMBLY (including solderless BENDER WIRTH as example) 1. Place pin on the side of the lens into relative hole on the holder. B Holder hole 4 3 1. Ensure correct relation of clamp and connector before screwing. Recommended torque 0.6Nm. 3. Attach optic by aligning the holes in the holder with hooks and turning the optic holder clockwise until it locks. 2. Press the lens under clips on the holder, ensuring both clips are fixed. Bender&Wirth model 4xx Typ L1 Clip Pin Align clamp positioning pin with holes in the connector. 2 Clip Tolerances if not otherwise shown According to DIN ISO 2768-1 Linear measures: up to 30mm class M, otherwise class C According to DIN ISO 2768-2 Form and position: class L THIRD ANGLE PROJECTION: 1 This drawing is the property of il Oy. It may not be reproduced, copied or communicated without a written agreement with il Oy. G 2 FIN 24240 SALO DRAWING TITLE RONDA-family SIZE 1 PART NUMBER A3 SCALE H 3 2. Assemble, BENDER&WIRTH connector and C13658_CLAMP-VERO13-18 clamp on heatsink with M3 screw. Pin DET B 1:1 WEIGHT - B SHEET A 3/3