available KW 22-2004 Description New Slot 12NC PR5510/04 Serial I/O RS232 und RS485/422 1/2 9405 355 10041 PR5510/06 PR5510/07 PR5510/08 PR5510/09 PR5510/12 PR5510/14 PR1721/31 PR1721/32 PR1721/34 PR1721/35 1 Analogoutput 0/4-20mA 4 analog In- / 1 analog Output BCD open emitter BCD open collector 6 digital In-/ 12 digital Outputs Ethernet incl. ModBus TCP Profibus DP Slave Interbus S Slave DeviceNet Slave CC-Link -planned- 3 1/2 1/2 1/2 1/2 4 4 4 4 4 9405 355 10061 9405 355 10041 9405 355 10081 9405 355 10091 9405 355 10121 9405 355 10141 9405 317 21311 9405 317 21321 9405 317 21341 9405 317 21351 PR8901/81 Licence internal Alibi-memory 9405 389 01811
PR5510/04 Connection mode: No. of channels: Type: Transfer rate: Signals RS 232C (V24) Signals RS 422/485: Potential isolation: Cable length: Cable type: Accessories: Dimensions: Weight: 2x DSUB 9-pole socket (female) 1x RS 232, 1x RS 422/485 RS 232 full duplex RS 422/485 full duplex (4-wire) RS 485 half duplex (2 -wire) 300 to 9600 to 19k2 Bit/sec Output:TD, RTS, DTR Input: RD, CTS, DCD, RI TxA, RxA, TxB, RxB RS 232 no, RS 422 / 485 yes max. 15m with RS 232 max. 1000 m with RS 422 / 485 Pairwisely twisted, screened (i.e. LifYCY 3x2x0,20), 1 conductor pair for (GND). 2x connector counterpart DSUB9 (male) incl. screening hoods (LxBxH): 86 x 52 x 15 mm 33 g
PR5510/06 Connection mode: No of outputs: Output: Range: Resolution: Linearity error: Temperature effect: Zero error: FSD error: Load: Cable length: Accessories: 3pol. Combicon Connector 1 current output 20mA (voltage-output-10v only with external 500 Ohm resistor) Gross-, Net weight or applikation dependent. 0/4...20mA, configurable via SETUP 16 Bit binary, 20.000 internal divisions for e.g. 0-20mA @0-20mA: 0,04% @4-20mA: 0,02% < 100ppm/K 0,05% < 0,1% 0...500 Ohm max. short circuit proof, potential isolated max. 150m (current output) 3pol. Combicon-plug in/screw
PR5510/08 Connection mode: No of outputs: No of Inputs: Output stage: External supply: Voltage drop: Input (enable): Load: Cable length: Accessories: 1x DSUB 26-pole socket (female) 6 digits BCD or 24 Bit binary (with I/O config.) 1 Bit (DATA IN) Common Collector at +Uext. Open Emitter (Load -> GND) +5V...+24V, max.32v approx.1,7v 5V/24V adjustable via S101 @5V high>3,1v, low<1,5v @24Vhigh>16V, low<10v Protected against wrong polarity max. 50mA, no potential isolation max. 50m (screened) 1x connector counterpart DSUB26 (male) incl. Screening hoods optinal with 3m cabel (open ends)
PR5510/09 Connection mode: No of outputs: No of Inputs: Output stage: External supply: Voltage drop: Input (enable): Load: Cable length: Accessories: 1x DSUB 26-pole socket (female) 6 digits BCD or 24 Bit binary (with I/O config.) 1 Bit (DATA IN) Common Emitter at GND Open Collector (Load -> +Uext) +5V...+24V, max.32v approx.1,7v 5V/24V adjustable via S101 @5V high>3,1v, low<1,5v @24Vhigh>16V, low<10v Protected against wrong polarity max. 50mA, no potential isolation max. 50m (screened) 1x connector counterpart DSUB26 (male) incl. Screening hoods optinal with 3m cabel (open ends)
PR5510/12 Connection mode: Number In-/ Outputs: Input signal: Input current: Output: Potential isolation Cable length: Accessories: Optional: 1x DSUB 37-pole socket (female) 6 12 Low 0...5V bzw. offen high 10...31V passiv <7mA@24V <3mA@12V protected against wrong polarity max. 32V, 25mA voltage drop @25mA: 3V protected against wrong polarity, passiv yes, via opto-coupler max. 50m (screened) 1x connector counterpart DSUB37 (male) incl. screening hoods PR 1623/10 4m connection cable PR 1623/20 Relais-terminal unit PR 1623/30 Terminal unit
PR1623/20 PR1623/30 PR1623/10
NEW Connection mode: internal Connection mode: external Output: Input: 34-pole socket (male) with flat cable for Slot-1 or Slot-2 2-row, 15-pole SUBD socket (female) 1 current output, voltage output with external resistor (spec. Refer to PR 5510/06). activ = supply by internal power supply 4 channels current resp. voltage input passiv = * external supply necessary! PR5510/07 Input range: Input resolution: Input Accuracy: Linearity error: Temperature effect: Potential isolation: Accessories: 0... 20 ma, input resistance 250 Ohm 0... 10 V, input resistance 100 kohm 0... 5 V, input resistance >10 MOhm 3.000 internal digits proportionate e.g. 0-20 ma / 0... 10 V (Reserve +- 15%, i.e. 1,5V... +11,5V ) 0,2% <0,003% <50ppm/K Output yes, Input no 1 connector counterpart SubD 15-pole PR5510/07 can not be used when SLOT-4 contains a fieldbus option. Reason: Overload of power supply
NEW - Fieldbusoptions
Fieldbusoptions Functions Read window Write window Fieldbus Module 1 Firmware functions Read: -Gross, Net, Tare etc. Write: -Tare, Untare etc. Module 2 application related functions e.g. BATCH, IBC please refer to manual Module 3 Functions, defined by user programming
NEW Connection mode: int. Connection mode: ext. Transfer rate: Kind of connection: Protocol: Transport: Cable: Cable impedancy: Certificates: Potential isolation: Cable length to hub: 34-pole socket (male) with flat cabel for Slot-4 RJ45 socket at back panel 10Mbit/sec (10BaseT, Ethernet) and 100Mbit/sec (100BaseTx, Fast Ethernet) Auto detection (10/100, HalfD/FullD) Network EW_COMM, Modbus/TCP TCP/IP or UDP/IP Pairwisely twisted, screened e.g. patchcable CAT5 accord. to use (straight/crossover) 150 Ohm Compatibel according to: Modbus Organisation for ModBus-TCP standard Industrial proved CE, UL, cul yes max. 30 m PR 5510/14 Ethernet PR5510/14 can not be used if already two active analog outputs are used. Reason: Overload of power supply The option will be supported from firmware release R3.12 onwards.
NEW Connection mode: int. Connection mode: ext. Transfer rate: Kind of connection: Protocol: Transport: Cable: Cable impedance: Bus connection: Certificates: Potential isolation: 34-pole socket (male) with flat cabel for Slot-4 9-pole SubD socket (female) 9.6 kbit/s up to 12 Mbit/s auto baudrate detection Profibus-Network, open / close of connections without interrupting other stations PROFIBUS-DP-V0 SLAVE acc. EN 50 170 (DIN 19245) Mono- or Multi-Master systems are supported. Master and Slave Devices, max. 126 nodes possible. Per module 244Byte OUT and 244Byte IN, in Total 416, typical 32Byte Watch-Dog Timer EIA RS 485, Profibus DIN 19245 Part 1 Pairwisely twisted, screened 150 Ohm per DIL, activated external Profibus Test-Center Comdec in Germany and PNO (Profibus User Organisation) Industrial proved CE, UL und cul Optocoupler in Line-A and B (RS 485) PR 1721/31 Cable length: max. distance 200m at 1.5 Mbit/s expandable by additional Repeater The option will be supported from firmware release R3.12 onwards.
NEW Connection mode: int. Connection mode: ext. Transfer rate: Kind of connection: Protocol: Transport: Cable: Cable impedance: Bus connection: Certificates: 34-pole socket (male) with flat cabel for Slot-4 IBS standard 9-pole SubD female OUT and male IN 500kbit/s or 2 Mbit/s, adjustable point_zu_point, active coupled ring INTERBUS-S SLAVE-international (IEC 61158 part 3 to 6), national (DIN 19258), European Standard (EN 50254) Cyclic data transfer with max. 10 words I/O. PCP 2.0 Parameterchannel with max 4 words. PMS 2.0 service: Initiate, Abort, Reject, Status, Identify Get-OD (long), Read, Write RS 422 Interbus special-cable colour: May green 3x2 Pairwisely twisted, screened 150 Ohm Not applicable, for active ring By Interbus-Club: compatibility to Interbus Standard Industrial proved CE, UL und cul PR1721/32 Potential isolation: Cable length: Optocoupler in Line-A and B (RS 422) The option will be supported from firmware release R3.12 onwards.
NEW Connection mode: int. Connection mode: ext. Transfer rate: Kind of connection: Protocol: Transport: Cable: Cable impedance: Bus connection: Certificates / Conformity: Potential isolation: Cable length: 34-pole socket (male) with flat cabel for Slot-4 5-pole screw terminal block (withdrawable) at back panel 125, 250 and 500kbit/s as Setup-Param bidirectional Parallel-Bus DeviceNet SLAVE Max 512 bytes cyclic Input and Output Data. Max 2048 bytes a cyclic Input and Output Data. EIA RS 485 2x2 Pairwisely twisted, screened 150 Ohm 120 Ohm at both ends necessary (CAN_H <-> CAN_L) Compatible to DeviceNet Spec. Vol 1: 2.0, Vol 2: 2.0 ODVA Certificate acc. Conformity software Version A-12 Industrial proved CE, UL und cul yes, completely galvanic isolated PR1721/34 The option will be supported from firmware release R3.12 onwards.