Report No R-RFCEP02V01. Test Report MSI / MS-6837D. Date of Receipt Aug. 21, Issued Date Sep. 11, PDF Free Download

Test Report Product Name Model No. Transmitter Module Notebook MS-163D, EX610 Atheros / AR5BXB63 MSI / MS-6837D Applicant Address MICRO-STAR INTL Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. Date of Receipt Aug. 21, 2007 Issued Date Sep. 11, 2007 Report No. 078286R-RFCEP02V01 The Test Results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: 1 of 48

Test Report Certification Issued Date: Sep. 11, 2007 Report No.: 078286R-RFCEP02V01 Product Name Applicant Address Manufacturer Model No. Rated Voltage Working Voltage Trade Name Notebook MICRO-STAR INTL Co., LTD. No. 69, Li-De St., Jung-He City, Taipei Hsien, Taiwan, R.O.C. MICRO-STAR INTL Co., LTD. MS-163D, EX610 AC 230V/50Hz AC 100-240V/50-60Hz MSI Applicable Standard ETSI EN 301 489-17:V1.2.1 (2002-08) ETSI EN 301489-1: V1.6.1 (2005-09) Test Result Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : Tested By : Approved By : ( Senior Engineering Adm. Specialist / Anita Chou ) (Assistant Engineer/ Joy Liu ) ( Deputy Manager / V i n c e n t L i n ) 0914 Page: 2 of 48

TABLE OF CONTENTS Description Page 1. GENERAL INFORMATION...5 1.1. EUT Description...5 1.2. Tested System Details...7 1.3. Configuration of Test System...8 1.4. EUT Exercise Software...8 1.5. Test Facility...9 2. Conducted Emission...10 2.1. Test Equipmen...10 2.2. Test Setup...10 2.3. Limits...11 2.4. Test Procedure...12 2.5. Test Specification...12 2.6. Uncertainty...12 2.7. Test Result...12 3. Radiated Emission...13 3.1. Test Equipment...13 3.2. Test Setup...13 3.3. Limits...14 3.4. Test Procedure...14 3.5. Test Specification...14 3.6. Uncertainty...14 3.7. Test Result...14 4. Power Harmonics, Voltage Fluctuation and Flicker...15 4.1. Test Equipment...15 4.2. Test Setup...15 4.3. Limits...15 4.4. Test Procedure...16 4.5. Test Specification...16 4.6. Uncertainty...16 4.7. Test Result...16 5. Electrostatic Discharge (ESD)...17 5.1. Test Equipment...17 5.2. Test Setup...17 5.3. Test Level...17 5.4. Test Procedure...18 5.5. Test Specification...18 5.6. Uncertainty...18 5.7. Test Result...18 6. Radiated Susceptibility (RS)...19 6.1. Test Equipment...19 6.2. Test Setup...19 6.3. Test Level...19 6.4. Test Procedure...20 6.5. Test Specification...20 6.6. Uncertainty...20 6.7. Test Result...20 7. Electrical Fast Transient/Burst (EFT/B)...21 7.1. Test Equipment...21 Page: 3 of 48

7.2. Test Setup...21 7.3. Test Level...22 7.4. Test Procedure...22 7.5. Test Specification...22 7.6. Uncertainty...22 7.7. Test Result...22 8. Surge...23 8.1. Test Equipment...23 8.2. Test Setup...23 8.3. Test Level...23 8.4. Test Procedure...24 8.5. Test Specification...24 8.6. Uncertainty...24 8.7. Test Result...24 9. Conducted Susceptibility (CS)...25 9.1. Test Equipment...25 9.2. Test Setup...25 9.3. Test Level...25 9.4. Test Procedure...26 9.5. Test Specification...26 9.6. Uncertainty...26 9.7. Test Result...26 10. Voltage Dips and Interruption...27 10.1. Test Equipment...27 10.2. Test Setup...27 10.3. Test Level...27 10.4. Test Procedure...28 10.5. Test Specification...28 10.6. Uncertainty...28 10.7. Test Result...28 11. EMC Reduction Method During Compliance Testing...29 12. Test Result...30 12.1. Test Data of Conducted Emission...31 12.2. Test Data of Radiated Emission...36 12.3. Test Data of Power Harmonics, Voltage Flucturation and Flicker...37 12.4. Test Data of Electrostatic Discharge...40 12.5. Test Data of Radiated Susceptibility...41 12.6. Test Data of Electrical Fast Transient...42 12.7. Test Data of Surge...43 12.8. Test Data of Conducted Susceptibility...44 12.9. Test Data of Voltage Dips and Interruption...45 Attachment 1: EUT Test Photographs Attachment 2: EUT Detailed Photographs Reference : Laboratory of License Page: 4 of 48

1. GENERAL INFORMATION 1.1. EUT Description Product Name Trade Name Model No. Working Voltage Frequency Range Channel Number Data Rate Channel Separation Type of Modulation Channel Control Antenna Gain Antenna type Power Adapter Notebook MSI MS-163D, EX610 AC 230V/50Hz 802.11b/g: 2400-2483.5MHz Bluetooth: 2402-2480MHz 802.11b/g: 13CH Bluetooth: 79 CH DSSS: 1, 2, 5.5, 11Mbps OFDM: 6, 9, 12, 18, 24, 36, 48, 54Mbps Bluetooth: 2Mbps 802.11b/g: 5MHz DSSS/OFDM Auto Refer to the table Antenna List Connector Delta, ADP-90SB BB Input: AC 100-240V, 50/60Hz, 1.5A Output: DC 19V, 4.74A Cable Out: Shielded, 1.8m, with one ferrite core bonded. Power Cord: Shielded, 1.8m Antenna List No. Manufacturer Part No. Peak Gain 1 HIGH-TEK S79-1800260-H39 (Main) S79-1800270-H39 (Aux) -0.87dBi for 2.4 GHz -4.27 dbi for 5.0 GHz Page: 5 of 48

DSSS Working Frequency of Each Channel: Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 01: 2412 MHz Channel 02: 2417 MHz Channel 03: 2422 MHz Channel 04: 2427 MHz Channel 05: 2432 MHz Channel 06: 2437 MHz Channel 07: 2442 MHz Channel 08: 2447 MHz Channel 09: 2452 MHz Channel 10: 2457 MHz Channel 11: 2462 MHz Channel 12: 2467 MHz Channel 13: 2472 MHz Frequency of Each Channel (Bluetooth): Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 00: 2402 MHz Channel 20: 2422 MHz Channel 40: 2442 MHz Channel 60: 2462 MHz Channel 01: 2403 MHz Channel 21: 2423 MHz Channel 41: 2443 MHz Channel 61: 2463 MHz Channel 02: 2404 MHz Channel 22: 2424 MHz Channel 42: 2444 MHz Channel 62: 2464 MHz Channel 03: 2405 MHz Channel 23: 2425 MHz Channel 43: 2445 MHz Channel 63: 2465 MHz Channel 04: 2406 MHz Channel 24: 2426 MHz Channel 44: 2446 MHz Channel 64: 2466 MHz Channel 05: 2407 MHz Channel 25: 2427 MHz Channel 45: 2447 MHz Channel 65: 2467 MHz Channel 06: 2408 MHz Channel 26: 2428 MHz Channel 46: 2448 MHz Channel 66: 2468 MHz Channel 07: 2409 MHz Channel 27: 2429 MHz Channel 47: 2449 MHz Channel 67: 2469 MHz Channel 08: 2410 MHz Channel 28: 2430 MHz Channel 48: 2450 MHz Channel 68: 2470 MHz Channel 09: 2411 MHz Channel 29: 2431 MHz Channel 49: 2451 MHz Channel 69: 2471 MHz Channel 10: 2412 MHz Channel 30: 2432 MHz Channel 50: 2452 MHz Channel 70: 2472 MHz Channel 11: 2413 MHz Channel 31: 2433 MHz Channel 51: 2453 MHz Channel 71: 2473 MHz Channel 12: 2414 MHz Channel 32: 2434 MHz Channel 52: 2454 MHz Channel 72: 2474 MHz Channel 13: 2415 MHz Channel 33: 2435 MHz Channel 53: 2455 MHz Channel 73: 2475 MHz Channel 14: 2416 MHz Channel 34: 2436 MHz Channel 54: 2456 MHz Channel 74: 2476 MHz Channel 15: 2417 MHz Channel 35: 2437 MHz Channel 55: 2457 MHz Channel 75: 2477 MHz Channel 16: 2418 MHz Channel 36: 2438 MHz Channel 56: 2458 MHz Channel 76: 2478 MHz Channel 17: 2419 MHz Channel 37: 2439 MHz Channel 57: 2459 MHz Channel 77: 2479 MHz Channel 18: 2420 MHz Channel 38: 2440 MHz Channel 58: 2460 MHz Channel 78: 2480 MHz Channel 19: 2421 MHz Channel 39: 2441 MHz Channel 59: 2461 MHz Note: 1. QuieTek verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: EMI Mode EMS Mode Mode1: Normal Operation (AR5BXB63+MS-6837D) Mode1: Normal Operation (AR5BXB63+MS-6837D) Page: 6 of 48

1.2. Tested System Details The types for all equipment, plus descriptions of all cables used in the tested system (including inserted cards) are: Product Manufacturer Model No. Serial No. Power Cord 1 Monitor SONY CPD-G500 2706563 Non-Shielded, 1.8m 2 Walkman AIWA HS-TA164 N/A N/A 3 Keyboard Logitech Y-SM46 867404-0121 N/A 4 USB Mouse Logitech M-UV83 HCB54904471 N/A 5 Microphone & Earphone PCHOME N/A N/A Non-Shielded, 2.0m 6 USB 2.0 HDD AACOM F12-UF N/A Power by PC 7 USB 2.0 HDD AACOM F12-UF N/A Power by PC 8 Printer EPSON StyLus C63 FAPY093574 Non-Shielded, 1.9m 9 Monitor BenQ LT-20E17 N/A Non-Shielded, 1.8m 10 TS9980 R&S N/A N/A N/A 11 Notebook PC DELL PP18L 36119001664 Non-Shielded, 0.8m 12 Exchange Network Sun Moon Star PX-4 95170087 Non-Shielded, 1.8m Signal Cable Type Signal cable Description A Audio Cable Non-Shielded, 1.6m B USB Cable Shielded, 1.5m C USB Cable Shielded, 1.5m D Microphone & Earphone Cable Non-Shielded, 1.6m E USB Cable Shielded, 1.5m F 1394 Cable Shielded, 1.2m G HDMI Cable Shielded, 1m H S-VIDEO Cable Shielded, 1.6m I COAXIAL Cable Shielded, 7.0m J LAN Cable Non-Shielded, 7.0m K USB Cable Shielded, 1.5m L D-SUB Cable Shielded, 1.8m, with two ferrite cores bonded M TELECOM Cable Non-Shielded, 7.0m N TELECOM Cable Non-Shielded, 7.0m Page: 7 of 48

1.3. Configuration of Test System 1.4. EUT Exercise Software (1) Setup the EUT and simulators as shown on 1.3. (2) Turn on the power of all equipment. (3) Boot the PC from Hard Disk. (4) PC reads test software from disk The Notebook PC's and far Notebook PC's monitor will show the transmitting and receiving (5) characteristics when the communication is success. (6) Wireless LAN function was used to perform the wireless data transmission. (7) Repeat the above procedure 5 to 6. Page: 8 of 48

1.5. Test Facility Ambient conditions in the laboratory: Items Test Item Required (IEC 68-1) Actual Temperature ( C) 15-35 20-35 Humidity (%RH) IEC 61000-4-2 30-60 50-55 Barometric pressure (mbar) 860-1060 950-1000 Temperature ( C) 15-35 20-35 Humidity (%RH) IEC 61000-4-5 10-75 50-65 Barometric pressure (mbar) 860-1060 950-1000 Temperature ( C) IEC 61000-4-4 15-35 20-35 Barometric pressure (mbar) IEC 61000-4-11 860-1060 950-1000 Site Description: Accredited by NVLAP NVLAP Lab Code: 200533-0 Site Name: Site Address: Accredited by DNV Statement No. : 413-99-LAB11 Accredited by Nemko Certificate No.: ELA 165 Accredited by TUV Rheinland Certificate No.: 10011438-1-2004 Accredited by CNLA Accredited Number: 0914 Quietek Corporation No. 5-22, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : 886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : service@quietek.com 0914 Page: 9 of 48

2. Conducted Emission 2.1. Test Equipmen The following test equipment are used during the conducted emission test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Remark 1 Test Receiver R & S ESCS 30 / 825442/018 Sep., 2007 2 Artificial Mains Network R & S ENV4200 / 848411/10 Feb., 2007 Peripherals 3 LISN R & S ESH3-Z5 / 825562/002 Feb., 2007 EUT 4 Pulse Limiter R & S ESH3-Z2 / 357.8810.52 Feb., 2007 5 4-wire ISN R & S ENY41 / 837032/001 Feb., 2007 6 Double 2-Wire ISN R & S ENY22 / 835354/008 Feb., 2007 7 No.1 Shielded Room Note: All equipment upon which need to calibrated are with calibration period of 1 year. 2.2. Test Setup Shielded Room 0.8m Peripheral ( EUT ) 40cm 80cm AMN for Peripheral AMN for EUT 50 ohm Terminator Test Receiver Page: 10 of 48

2.3. Limits (1) Mains terminal Frequency MHz Limits (dbuv) Limit for conducted emissions of equipment intended to be used in Limit for conducted emissions telecommunication centers only QP AV QP AV 0.15-0.50 79 66 66-56 56-46 0.50-5.0 73 60 56 46 5.0-30 73 60 60 50 Remarks: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz ~ 0.50 MHz. (2) Telecommunication ports Limits (dbuv) Frequency MHz Limit for conducted emissions from telecommunication ports of equipment intended for use in telecommunication centers only Limit for conducted emissions from telecommunication ports QP AV QP AV 0.15 0.50 97-87 84-74 84-74 74-64 5.0 30 87 74 74 64 Remarks: In the above table, the tighter limit applies at the band edges. Page: 11 of 48

2.4. Test Procedure AC Mains: The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50ohm /50uH coupling impedance with 50ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of AC line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ETSI EN 301489-1: V1.6.1 (2005-09) on conducted measurement. The bandwidth of the field strength meter (R & S Test Receiver ESCS 30) is set at 9kHz. Telecommunication Port: The mains voltage shall be supplied to the EUT via the LISN when the measurement of telecommunication port is performed. The common mode disturbances at the telecommunication port shall be connected to the ISN, which is 150ohm impedance. Both alternative cables are tested related to the LCL requested. The measurement range is from 150kHz to 30MHz. The bandwidth of measurement is set to 9kHz. The 60dB LCL ISN is used for cat. 5 cable, 50dB LCL ISN is used for cat. 3 and 80dB LCL is wed for alternative one. 2.5. Test Specification According to ETSI EN 301489-1: V1.6.1 (2005-09) EN 55022:1998+A1: 2000 +A2: 2003 2.6. Uncertainty ± 2.26 db 2.7. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 12 of 48

3. Radiated Emission 3.1. Test Equipment The following test equipment are used during the Radiated emission test: Test Site Equipment Manufacturer Model No./Serial No. Last Cal. Site # 1 Test Receiver R & S ESVS 10 / 834468/003 July, 2007 Spectrum Analyzer Advantest R3162/ 00803480 May, 2007 Pre-Amplifier Advantest BB525C/ 3307A01812 May, 2007 Bilog Antenna SCHAFFNER CBL6112B / 2697 Nov., 2006 Site # 2 Test Receiver R & S ESCS 30 / 836858 / 022 Nov., 2006 Spectrum Analyzer Advantest R3162 / 100803466 May, 2007 Pre-Amplifier Advantest BB525C/3307A01814 May, 2007 Bilog Antenna SCHAFFNER CBL6112B / 2705 Oct., 2006 Horn Antenna ETS 3115 / 0005-6160 July, 2007 Pre-Amplifier QTK QTK-AMP-01/ 0001 July, 2007 Site # 3 Test Receiver R & S ESI 26 / 838786 / 004 May, 2007 Spectrum Analyzer Advantest R3162 / 100803480 May, 2007 Pre-Amplifier QTK QTK-AMP-03 / 0003 May, 2007 Bilog Antenna SCHAFFNER CBL6112B / 2697 May, 2007 Horn Antenna ETS 3115 / 0005-6160 July, 2007 Pre-Amplifier QTK QTK-AMP-01 / 0001 July, 2007 Note: 1. All equipments are calibrated every one year. 2. The test instruments marked by X are used to measure the final test results. 3.2. Test Setup 10m FRP Dome 1m to 4m Non-Conducted Table Load EUT Antenna Mast Dipole or Horn Antenna Antenna height can be moved from 1m to 4m, Antenna and turntable distance 3m 80cm Test Receiver Fully Soldered Ground Plane TO Controller To Receiver Page: 13 of 48

3.3. Limits Limits (dbuv/m) Frequency MHz Limit for radiated emissions from ancillary equipment intended for use in telecommunication centers only, and measured on a stand alone basis QP Limit for radiated emissions from ancillary equipment, measured on a stand alone basis QP 30-230 40 30 230-1000 47 37 3.4. Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above ground. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters.the antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to ETSI EN 301489-1: V1.6.1 (2005-09) on radiated measurement. The additional motch filter below 1GHz was used to measure the level of harmonics radiated emission during field dtrength of harmonics measurement. The bandwidth below 1GHz setting on the field strength meter (R&S Test Receiver ESCS 30 )is 120 khz, and 1MHz bandwidth is adpted above 1GHz. The frequency range from 30MHz to 10 th harmonics is checked. 3.5. Test Specification According to ETSI EN 301489-1: V1.6.1 (2005-09) EN 55022:1998+A1: 2002+A2: 2003 3.6. Uncertainty ± 3.8 db 3.7. Test Result The emission from the EUT was below the specified limits. The worst-case emissions are shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 14 of 48

4. Power Harmonics, Voltage Fluctuation and Flicker 4.1. Test Equipment Item Instrument 4Manufacturer Type No/Serial No. Last Calibration 1 Power Harmonics Tester SCHAFFNER Profline 2105-400 S/N: HK54148 June, 2007 2 Analyzer SCHAFFNER CCN 1000-1/X71887 June, 2007 3 No.3 Shielded Room Note: All equipments are calibrated every one year. 4.2. Test Setup Controller PC Power Analyzer Impedance Network Power Source EUT Load Non-Conducted 4.3. Limits Limits of Class A Harmonics Currents Harmonics Order n Maximum Permissible harmonic current A Odd harmonics Harmonics Order n Maximum Permissible harmonic current A Even harmonics 3 2.30 2 1.08 5 1.14 4 0.43 7 0.77 6 0.30 9 0.40 8 n 40 0.23 * 8/n 11 0.33 13 0.21 15 n 39 0.15 * 15/n Limits of Class B Harmonics Currents For Class B equipment, the harmonic of the input current shall not exceed the maximum permissible values given in table that is the limit of Class A multiplied by a factor of 1.5. Page: 15 of 48

Limits of Class C Harmonics Currents Report No. 078286R-RFCEP02V01 Harmonics Order Maximum Permissible harmonic current Expressed as a percentage of the input current at the fundamental frequency n % 2 2 3 30.λ * 5 10 7 7 9 5 11 n 39 3 (odd harmonics only) *λ is the circuit power factor Limits of Class D Harmonics Currents Harmonics Order Maximum Permissible harmonic current per watt ma/w Maximum Permissible harmonic current A n 3 3.4 2.30 5 1.9 1.14 7 1.0 0.77 9 0.5 0.40 11 0.35 0.33 13 n 39 (odd harmonics only) 4.4. Test Procedure 3.85/n See limit of Class A The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed. 4.5. Test Specification According to EN 61000-3-2:2000+A1: 2001, EN 61000-3-3:1995+A1: 2001 4.6. Uncertainty ± 3.23 % 4.7. Test Result The measurement of the power harmonics, which test at the extremes of EUT s supply range, was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Test Result: (See Test Result) PASS FAIL Note: According to clause 7 of EN 61000-3-2: 2000, equipment with a rated power of 75W or less, no limits apply. The test result is only for reference. Page: 16 of 48

5. Electrostatic Discharge (ESD) 5.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 ESD Simulator System SCHAFFNER NSG-438 S/N: 167 June, 2007 2 Horizontal Coupling Plane (HCP) 3 Vertical Coupling Plane (VCP) 4 No.3 Shielded Room QuieTek HCP AL50 N/A QuieTek VCP AL50 N/A Note: All equipments are calibrated every one year. 5.2. Test Setup Vertical Coupling Plane Insulation EUT Loads: Active Horizontal Coupling Plane 80cm Non-Conducted table ESD Simulator 470K ohm Resistor Metal Ground Plane 470K ohm Resistor 5.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Electrostatic Discharge kv(charge Voltage) ±8 Air Discharge ±4 Contact Discharge B Page: 17 of 48

5.4. Test Procedure Direct application of discharges to the EUT: Contact discharge was applied only to conductive surfaces of the EUT. Air discharges were applied only to non-conductive surfaces of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges will be keep longer 1 second. It was at least ten single discharges with positive and negative at the same selected point. The selected point, which was performed with electrostatic discharge, was marked on the red label of the EUT. Indirect application of discharges to the EUT: Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. 5.5. Test Specification According to EN 61000-4-2:1995+A1: 1998+A2: 2001 5.6. Uncertainty ± 6.003 % 5.7. Test Result The measurement of the electrostatic discharge was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 18 of 48

6. Radiated Susceptibility (RS) 6.1. Test Equipment Item Equipment Manufacturer Model No. / Serial No. Last Cal. 1 Signal Generator R & S SMY02 / 825454/029 Oct., 2006 2 Power Amplifier A & R 100W10000M7 / A285000010 N/A 3 RF Power Amplifier OPHIRRF 5022F / 1075 N/A 4 Bilog Antenna Chase CBL6112B / 2452 Sep., 2007 5 Power Meter R & S NRVD / 100219 Jan., 2007 6 Directional Coupler A & R DC6180 / 22735 Jan., 2007 7 No.5 EMC Fully Chamber Note: All equipments are calibrated every one year. 6.2. Test Setup Antenna Mast 3 m Sensor Full-Anechoic Chamber Camera system EUT Load 1m 80cm Power Amplifier Field Meter Power Meter Signal Generator Computer controller Camera Monitor 6.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Enclosure Port Radio-Frequency MHz 80-1000 1400-2000 Electromagnetic Field V/m(Un-modulated, rms) 3 A Amplitude Modulated % AM (1kHz) 80 Page: 19 of 48

6.4. Test Procedure The EUT and load, which are placed on a table that is 0.8 meter above ground, are placed with one coincident with the calibration plane such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna and four sides of the EUT are set on measurement. In order to judge the EUT performance, a CCD camera is used to monitor EUT screen. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 3 V/m Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 80MHz - 1000MHz, 1400MHz - 2000MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 6.5. Test Specification According to EN 61000-4-3:1996+A1: 1998+A2: 2001 6.6. Uncertainty ± 6.17 % 6.7. Test Result The measurement of the radiated susceptibility was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 20 of 48

7. Electrical Fast Transient/Burst (EFT/B) 7.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration Fast Transient/Burst 1 Generator 2 No.2 Shielded Room SCHAFFNER NSG 2050 S/N: 200124-031AR June, 2007 Note: All equipments are calibrated every one year. 7.2. Test Setup Page: 21 of 48

7.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Ports for signal lines and control lines kv (Peak) +0.5 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 Input DC Power Ports kv (Peak) +0.5 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 Input AC Power Ports kv (Peak) +1 Fast Transients Common Mode Tr/Th ns 5/50 B Rep. Frequency khz 5 7.4. Test Procedure The EUT and load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. For Signal Ports and Telecommunication Ports: The EFT interference signal is through a coupling clamp device couples to the signal and control lines of the EUT with burst noise for 1min. For Input DC and AC Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the EFT interference signal. Each of the Line and Neutral conductors is impressed with burst noise for 1 min. The length of power cord between the coupling device and the EUT shall be 1m. 7.5. Test Specification According to EN 61000-4-4:1995+A1: 2001+A2: 2001 7.6. Uncertainty ± 8.80 % 7.7. Test Result The measurement of the Electrical Fast Transient/Burst was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 22 of 48

8. Surge 8.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Surge Generator SCHAFFNER NSG 2050 S/N: 200124-031AR 2 No.6 Shielded Room June, 2007 Note: All equipment upon which need to calibrated are with calibration period of 1 year. 8.2. Test Setup PC Surge Generator EUT Load Non-Conducted Table Non-Conducted Table 8.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria Telecommunication Ports (See 1) and 2)) Surges Tr/Th us Line to Ground kv Telecommunication Ports in Telecom Centres (See 1) and 2)) Surges Tr/Th us Line to Ground kv AC Input and AC Output Power Ports Surges Line to Line Line to Ground Tr/Th us kv kv AC Input and AC Output Power Ports in Telecom Centres Surges Tr/Th us Line to Line kv Line to Ground kv 1.2/50 (8/20) ± 1 1.2/50 (8/20) ± 0.5 1.2/50 (8/20) ±1 ± 2 1.2/50 (8/20) ±0.5 ± 1 B B B B Notes: 1) Applicable only to ports which according to the manufacturer s may directly to outdoor cables. 2) Where normal functioning cannot be achieved because of the impact of the CDN on the EUT, no immunity test shall be required. Page: 23 of 48

8.4. Test Procedure The EUT and its load are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The length of power cord between the coupling device and the EUT shall be 2m or less. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) device couples to the signal and Telecommunication lines of the EUT. For Input and Output AC Power or DC Input and DC Output Power Ports: The EUT is connected to the power mains through a coupling device that directly couples the Surge interference signal. The surge noise shall be applied synchronized to the voltage phase at 0 0, 90 0, 180 0, 270 0 and the peak value of the a.c. voltage wave. (Positive and negative) Each of Line-Earth and Line-Line is impressed with a sequence of five surge voltages with interval of 1 min. 8.5. Test Specification According to EN 61000-4-5:1995+A1+ 2001 8.6. Uncertainty ± 7.93 % 8.7. Test Result The measurement of the Surge was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 24 of 48

9. Conducted Susceptibility (CS) 9.1. Test Equipment Item Equipment Manufacturer Model No. / Serial No. Last Cal. 1 CS SYSTEM SCHAFFNER NSG 2070 March, 2007 2 CDN SCHAFFNER CDN M016S / 20822 Dec., 2006 3 CDN SCHAFFNER CDN M016S / 20823 Dec., 2006 4 FIXED PAD SCHAFFNER INA 2070-1 / 2115 N/A 5 EM Clamp KEMZ 801 / 21024 March, 2007 6 No.6 Shielded Room Note: All equipments are calibrated every one year. 9.2. Test Setup Aux equipment CDN EUT CDN Aux equipment Ground Reference Plane T Non-Conducted Table T2 RF-Generator PA 9.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output & DC Input and DC output Power Ports & Functional Earth Ports Radio-Frequency Common Mode. Amplitude Modulated MHz V (rms, Unmodulated) % AM (1kHz) Source Impedance Ω 0.15-80 3 80 150 A Page: 25 of 48

9.4. Test Procedure The EUT are placed on a table that is 0.8 meter height, and a Ground reference plane on the table, EUT are placed upon table and use a 10cm insulation between the EUT and Ground reference plane. For Signal Ports and Telecommunication Ports The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and Telecommunication lines of the EUT. For Input DC and AC Power Ports The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT. Used CDN-M2 for two wires or CDN-M3 for three wires. All the scanning conditions are as follows: Condition of Test Remarks 1. Field Strength 130dBuV(3V) Level 2 2. Radiated Signal AM 80% Modulated with 1kHz sinusoidal audio signal 3. Scanning Frequency 0.15MHz 80MHz 4 Dwell Time 3 Seconds 5. Frequency step size f : 1% 6. The rate of Swept of Frequency 1.5 x 10-3 decades/s 9.5. Test Specification According to EN 61000-4-6:1996 +A1: 2001 9.6. Uncertainty ± 6.17 % 9.7. Test Result The measurement of the Conducted Susceptibility was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 26 of 48

10. Voltage Dips and Interruption 10.1. Test Equipment Item Instrument Manufacturer Type No/Serial No. Last Calibration 1 Voltage Dips Generator SCHAFFNER NSG 2050 S/N: 200124-031AR 2 No.6 Shielded Room June, 2007 Note: All equipments are calibrated every one year. 10.2. Test Setup To AC Line Voltage Dips/ Interruptions /Variations Simulator AC Power Line to EUT EUT Load Non-Conducted Table 80cm Controller Computer Printer 10.3. Test Level Item Environmental Phenomena Units Test Specification Performance Criteria AC Input and AC Output Power Ports Voltage Dips % Reduction ms 30 10 B Voltage Dips % Reduction ms 60 100 C Voltage Interruptions % Reduction ms > 95 % 5000 C Page: 27 of 48

10.4. Test Procedure The EUT and its load are placed on a table which is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. And projected beyond the EUT by at least 0.1m on all sides. The power cord shall be used the shortest power cord as specified by the manufacturer. For Voltage Dips/ Interruptions test: The selection of test voltage is based on the rated power range. If the operation range is large than 20% of lower power range, both end of specified voltage shall be tested. Otherwise, the typical voltage specification is selected as test voltage. The EUT is connected to the power mains through a coupling device that directly couples to the Voltage Dips and Interruption Generator. The EUT shall be tested for 30% voltage dip of supplied voltage and duration 10ms, with a sequence of three voltage dips with intervals of 10 seconds, for 60% voltage dip of supplied voltage and duration 100ms with a sequence of three voltage dips with intervals of 10 seconds, and for 95% voltage interruption of supplied voltage and duration 5000ms with a sequence of three voltage interruptions with intervals of 10 seconds. Voltage phase shifting are shall occur at 0 0, 45 0, 90 0,135 0,180 0,225 0, 270 0,315 0 of the voltage. 10.5. Test Specification According to EN 61000-4-11:1994+A1: 2001 10.6. Uncertainty ± 2.03 % 10.7. Test Result The measurement of the Voltage Dips and Interruption was investigated and test result was shown in section 12. The EUT complies the acceptance criterion and passes the test. Page: 28 of 48

11. EMC Reduction Method During Compliance Testing No modification was made during testing. Page: 29 of 48

12. Test Result The test results in the emission and the immunity were performed according to the requirements of measurement standard and process. Quietek Corporation is assumed full responsibility for the accuracy and completeness of these measurements. The test data of the emission is listed as below. All the tests were carried out with the EUT in normal operation, which was defined as: EMI Mode EMS Mode Mode1: Normal Operation (AR5BXB63+MS-6837D) Mode1: Normal Operation (AR5BXB63+MS-6837D) Page: 30 of 48

12.1. Test Data of Conducted Emission Product : Notebook Test Item : Conducted Emission Test Site : No.1 Shielded Room Power Line : Line 1 Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv LINE 1 Quasi-Peak 0.150 0.202 53.860 54.062-11.938 66.000 0.201 0.202 42.390 42.592-21.951 64.543 0.822 0.230 40.550 40.780-15.220 56.000 2.076 0.277 42.420 42.697-13.303 56.000 7.802 0.534 38.780 39.314-20.686 60.000 22.564 1.051 38.760 39.811-20.189 60.000 Average 0.150 0.202 37.360 37.562-18.438 56.000 0.201 0.202 25.220 25.422-29.121 54.543 0.822 0.230 26.940 27.170-18.830 46.000 2.076 0.277 27.900 28.177-17.823 46.000 7.802 0.534 29.480 30.014-19.986 50.000 22.564 1.051 29.370 30.421-19.579 50.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 31 of 48

Product : Notebook Test Item : Conducted Emission Test Site : No.1 Shielded Room Power Line : Line 2 Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv LINE 2 Quasi-Peak 0.838 0.231 39.610 39.841-16.159 56.000 1.380 0.248 35.290 35.538-20.462 56.000 2.259 0.290 44.310 44.600-11.400 56.000 4.603 0.371 39.150 39.521-16.479 56.000 11.009 0.587 37.000 37.587-22.413 60.000 22.685 0.802 37.290 38.092-21.908 60.000 Average 0.838 0.231 28.020 28.251-17.749 46.000 1.380 0.248 19.220 19.468-26.532 46.000 2.259 0.290 31.110 31.400-14.600 46.000 4.603 0.371 28.720 29.091-16.909 46.000 11.009 0.587 28.800 29.387-20.613 50.000 22.685 0.802 28.160 28.962-21.038 50.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 32 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D)(LAN Cable-10 Mbps) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.642 9.763 54.940 64.703-9.297 74.000 1.045 9.734 60.750 70.484-3.516 74.000 2.087 9.748 59.440 69.188-4.812 74.000 4.947 9.766 49.930 59.696-14.304 74.000 8.752 9.807 56.890 66.697-17.303 84.000 12.502 9.827 59.920 69.747-14.253 84.000 Average 0.642 9.763 37.500 47.263-16.737 64.000 1.045 9.734 44.580 54.314-9.686 64.000 2.087 9.748 44.460 54.208-9.792 64.000 4.947 9.766 38.770 48.536-15.464 64.000 8.752 9.807 44.490 54.297-19.703 74.000 12.502 9.827 47.220 57.047-16.953 74.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 33 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) (GIGA CUR) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.884 0.111 10.040 10.151-19.849 30.000 1.185 0.116 14.320 14.436-15.564 30.000 1.443 0.119 16.160 16.279-13.721 30.000 1.775 0.123 25.340 25.463-4.537 30.000 2.099 0.128 24.030 24.158-5.842 30.000 3.029 0.140 11.100 11.240-18.760 30.000 Average 0.884 0.111-0.050 0.061-19.939 20.000 1.185 0.116 1.390 1.506-18.494 20.000 1.443 0.119 1.460 1.579-18.421 20.000 1.775 0.123 11.900 12.023-7.977 20.000 2.099 0.128 10.100 10.228-9.772 20.000 3.029 0.140 0.850 0.990-19.010 20.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 34 of 48

Product : Notebook Test Item : Impedance Stabilization Network Test Site : No.1 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) (GIGA VOL) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv db dbuv Quasi-Peak 0.447 20.106 37.200 57.306-18.208 75.514 0.775 20.110 33.230 53.340-20.660 74.000 0.880 20.111 34.810 54.921-19.079 74.000 2.072 20.127 38.310 58.437-15.563 74.000 5.599 20.174 27.790 47.964-26.036 74.000 8.689 20.216 30.990 51.206-32.794 84.000 Average 0.447 20.106 21.440 41.546-23.968 65.514 0.775 20.110 16.280 36.390-27.610 64.000 0.880 20.111 22.560 42.671-21.329 64.000 2.072 20.127 23.550 43.677-20.323 64.000 5.599 20.174 16.630 36.804-27.196 64.000 8.689 20.216 20.340 40.556-33.444 74.000 Note: 1. All Reading Levels are Quasi-Peak and Average value. 2. " " means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 35 of 48

12.2. Test Data of Radiated Emission Product : Notebook Test Item : General Radiated Emission Test Site : No.3 OATS Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Frequency Correct Reading Measurement Margin Limit Factor Level Level MHz db dbuv dbuv/m db dbuv/m Horizontal 184.490 11.345 7.930 19.274-10.726 30.000 301.850 17.083 7.170 24.252-12.748 37.000 362.200 19.489 3.320 22.809-14.191 37.000 480.110 22.670 5.400 28.070-8.930 37.000 500.000 23.073 1.200 24.273-12.727 37.000 580.000 24.776 3.200 27.976-9.024 37.000 639.180 25.365 1.250 26.615-10.385 37.000 786.690 27.334 1.500 28.834-8.166 37.000 Vertical 120.030 13.896 10.170 24.066-5.934 30.000 176.370 11.640 4.140 15.780-14.220 30.000 212.400 11.701 9.340 21.042-8.958 30.000 359.200 19.390 4.690 24.080-12.920 37.000 540.850 24.184 0.950 25.135-11.865 37.000 737.520 27.154 1.400 28.554-8.446 37.000 960.070 29.165 2.050 31.215-5.785 37.000 Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. means the worst emission level. 3. Measurement Level = Reading Level + Correct Factor Page: 36 of 48

12.3. Test Data of Power Harmonics, Voltage Flucturation and Flicker Product : Notebook Test Item : Power Harmonics Classification : Class D Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Test Result: Pass Source qualification: Normal Current & voltage waveforms 1.5 300 Current (Amps) 1.0 0.5 0.0-0.5-1.0 200 100 0-100 -200 Voltage (Volts) -1.5-300 Harmonics and Class D limit line European Limits Current RMS(Amps) 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 4 8 12 16 20 24 28 32 36 40 Harmonic # Test result: Pass Worst harmonic was #3 with 43.48% of the limit. Page: 37 of 48

Test Result: Pass Source qualification: Normal THC(A): 0.18 I-THD(%): 51.05 POHC(A): 0.003 POHC Limit(A): 0.034 Highest parameter values during test: V_RMS (Volts): 229.74 Frequency(Hz): 50.00 I_Peak (Amps): 1.036 I_RMS (Amps): 0.399 I_Fund (Amps): 0.351 Crest Factor: 2.621 Power (Watts): 79.7 Power Factor: 0.870 Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status 2 0.000 3 0.175 0.271 64.5 0.176 0.406 43.48 Pass 4 0.000 5 0.026 0.151 16.9 0.026 0.227 11.54 Pass 6 0.000 7 0.009 0.080 11.1 0.009 0.119 7.81 Pass 8 0.000 9 0.005 0.040 11.8 0.005 0.060 8.56 Pass 10 0.000 11 0.002 0.028 7.3 0.002 0.042 5.86 Pass 12 0.000 13 0.004 0.024 14.8 0.004 0.035 11.31 Pass 14 0.000 15 0.001 0.021 3.7 0.001 0.031 3.26 Pass 16 0.000 17 0.001 0.018 8.0 0.002 0.027 7.90 Pass 18 0.000 19 0.001 0.016 8.9 0.002 0.024 9.64 Pass 20 0.000 21 0.001 0.015 6.3 0.002 0.022 6.98 Pass 22 0.000 23 0.001 0.013 6.4 0.001 0.020 6.90 Pass 24 0.000 25 0.001 0.012 9.4 0.002 0.018 8.49 Pass 26 0.000 27 0.001 0.011 10.1 0.002 0.017 9.06 Pass 28 0.000 29 0.001 0.011 5.0 0.001 0.016 5.28 Pass 30 0.000 31 0.001 0.010 9.6 0.001 0.015 8.59 Pass 32 0.000 33 0.001 0.009 11.8 0.001 0.014 10.64 Pass 34 0.000 35 0.000 0.009 5.4 0.001 0.013 5.42 Pass 36 0.000 37 0.001 0.008 6.8 0.001 0.012 7.24 Pass 38 0.000 39 0.001 0.008 10.7 0.002 0.012 13.22 Pass 40 0.000 1.Dynamic limits were applied for this test. The highest harmonics values in the above table may not occur at the same window as the maximum harmonics/limit ratio. 2:According to EN61000-3-2 paragraph 7 the note 1 and 2 are valid for all applications having an active input power >75W. Others the result should be pass. Page: 38 of 48

Product : Notebook Test Item : Voltage Fluctuations and Flicker Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Test Result: Pass Status: Test Completed Pst i and limit line European Limits 1.00 0.75 Pst 0.50 0.25 19:00:22 Plt and limit line Plt 0.6 0.5 0.4 0.3 0.2 0.1 19:00:22 Parameter values recorded during the test: Vrms at the end of test (Volt): 229.61 Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (ms): 500.0 Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): 0.160 Test limit: 1.000 Pass Highest Plt (2 hr. period): 0.070 Test limit: 0.650 Pass Page: 39 of 48

12.4. Test Data of Electrostatic Discharge Product : Notebook Test Item : Electrostatic Discharge Test Site : No.3 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Item Amount of Discharge Voltage Required Criteria Complied To Criteria (A, B, C) Results Air Discharge 10 10 +8kV -8kV B B B B Pass Pass Contact Discharge 25 25 +4kV -4kV B B B B Pass Pass Indirect Discharge 50 +4kV B A Pass (HCP) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Front) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Left) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Back) 50-4kV B A Pass Indirect Discharge 50 +4kV B A Pass (VCP Right) 50-4kV B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. NR: No Requirement Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv. No false alarms or other malfunctions were observed during or after the test. Page: 40 of 48

12.5. Test Data of Radiated Susceptibility Product : Notebook Test Item : Radiated Susceptibility Test Site : No.5 EMC fully Chamber Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Frequency (MHz) Position (Angle) Polarity (H or V) Field Strength (V/m) Required Criteria Complied To Criteria (A, B, C) Results 80-1000 Front H 3 A A Pass 80-1000 Front V 3 A A Pass 80-1000 Back H 3 A A Pass 80-1000 Back V 3 A A Pass 80-1000 Left H 3 A A Pass 80-1000 Left V 3 A A Pass 80-1000 Right H 3 A A Pass 80-1000 Right V 3 A A Pass 80-1000 Top H 3 A A Pass 80-1000 Top V 3 A A Pass 80-1000 Down H 3 A A Pass 80-1000 Down V 3 A A Pass 1400-2000 Front H 3 A A Pass 1400-2000 Front V 3 A A Pass 1400-2000 Back H 3 A A Pass 1400-2000 Back V 3 A A Pass 1400-2000 Left H 3 A A Pass 1400-2000 Left V 3 A A Pass 1400-2000 Right H 3 A A Pass 1400-2000 Right V 3 A A Pass 1400-2000 Top H 3 A A Pass 1400-2000 Top V 3 A A Pass 1400-2000 Down H 3 A A Pass 1400-2000 Down V 3 A A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information There was no observable degradation in performance. EUT stopped operation and could / could not be reset by operator at at frequency MHz. No false alarms or other malfunctions were observed during or after the test. V/m Page: 41 of 48

12.6. Test Data of Electrical Fast Transient Product : Notebook Test Item : Electrical Fast Transient Test Site : No.2 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Inject Line Polarity Voltage (kv) Inject Time (Second) Inject Method Required Criteria Complied to Criteria Result L + N +PE ± 1 60 Direct B A Pass LAN ± 0.5 90 Clamp B A Pass Telecom ± 0.5 90 Clamp B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 42 of 48

12.7. Test Data of Surge Product : Notebook Test Item : Surge Test Site : No. 6 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Inject Line Polarity Angle Voltage (kv) Time Interval (Second) Inject Method Required Criteria Complied to Criteria Result L-N ± 0 1 60 Direct B A Pass L-N ± 90 1 60 Direct B A Pass L-N ± 180 1 60 Direct B A Pass L-N ± 270 1 60 Direct B A Pass N-PE ± 0 2 60 Direct B A Pass N-PE ± 90 2 60 Direct B A Pass N-PE ± 180 2 60 Direct B A Pass N-PE ± 270 2 60 Direct B A Pass L+PE ± 0 2 60 Direct B A Pass L+PE ± 90 2 60 Direct B A Pass L+PE ± 180 2 60 Direct B A Pass L+PE ± 270 2 60 Direct B A Pass Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A : Operate as intended during and after the test Meet criteria B : Operate as intended after the test Meet criteria C : Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at Line. No false alarms or other malfunctions were observed during or after the test. kv of Page: 43 of 48

12.8. Test Data of Conducted Susceptibility Product : Notebook Test Item : Conducted Susceptibility Test Site : No. 6 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Frequency Voltage Inject Tested Port of Required Performance Result Range Applied Method EUT Criteria Criteria (MHz) dbuv(v) Complied To 0.15~80 130(3V) CDN AC IN A A PASS 0.15~80 130(3V) Clamp LAN A A PASS 0.15~80 130(3V) Clamp LAN GIGA A A PASS 0.15~80 130(3V) Clamp Telecom A A PASS Note: The testing performed is from lowest level up to the highest level as required by standard, but only highest level is shown on the report. Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 44 of 48

12.9. Test Data of Voltage Dips and Interruption Product : Notebook Test Item : Voltage Dips and Interruption Test Site : No.6 Shielded Room Test Mode : Mode1: Normal Operation (AR5BXB63+MS-6837D) Voltage Dips and Interruption Reduction (%) Angle Test Duration (ms) Required Performance Criteria Performance Criteria Complied To Test Result 30 0 10 B A PASS 30 45 10 B A PASS 30 90 10 B A PASS 30 135 10 B A PASS 30 180 10 B A PASS 30 225 10 B A PASS 30 270 10 B A PASS 30 315 10 B A PASS 60 0 100 C A PASS 60 45 100 C A PASS 60 90 100 C A PASS 60 135 100 C A PASS 60 180 100 C A PASS 60 225 100 C A PASS 60 270 100 C A PASS 60 315 100 C A PASS >95 0 5000 C A PASS >95 45 5000 C A PASS >95 90 5000 C A PASS >95 135 5000 C A PASS >95 180 5000 C A PASS >95 225 5000 C A PASS >95 270 5000 C A PASS >95 315 5000 C A PASS Meet criteria A: Operate as intended during and after the test Meet criteria B: Operate as intended after the test Meet criteria C: Loss/Error of function Additional Information The nominal voltage of EUT is 230V. EUT stopped operation and could / could not be reset by operator at kv of Line. No false alarms or other malfunctions were observed during or after the test. The acceptance criteria were met, and the EUT passed the test. Page: 45 of 48

Attachment 1: EUT Test Photographs Page: 46 of 48

Report No.: 078286R-RFCEP02V01 Attachment 1: EUT Test Setup Photographs Front View of Conducted Test Back View of Conducted Test Page : 1 of 10

Report No.: 078286R-RFCEP02V01 Front View of Conducted Test (ISN) Back View of Conducted Test (ISN) Page : 2 of 10

Report No.: 078286R-RFCEP02V01 Front View of Conducted Test (GIGA CUR) Back View of Conducted Test (GIGA CUR) Page : 3 of 10

Report No.: 078286R-RFCEP02V01 Front View of Conducted Test (GIGA VOL) Back View of Conducted Test (GIGA VOL) Page : 4 of 10

Report No.: 078286R-RFCEP02V01 Front View of Radiated Test Back View of Radiated Test-Clamp Page : 5 of 10

Report No.: 078286R-RFCEP02V01 Power Harmonics Test Setup ESD Test Setup Page : 6 of 10

Report No.: 078286R-RFCEP02V01 Radiated Susceptibility Test Setup EFT/B Test Setup Page : 7 of 10

Report No.: 078286R-RFCEP02V01 EFT/B Test Setup Clamp SURGE Test Setup Page : 8 of 10

Report No.: 078286R-RFCEP02V01 Conducted Susceptibility Test Setup Conducted Susceptibility Test Setup- Clamp Page : 9 of 10

Report No.: 078286R-RFCEP02V01 Voltage Dips Test Setup Page : 10 of 10

Attachment 2: EUT Detailed Photographs Page: 47 of 48

Report No.: 078286R-RFCEP02V01 Attachment 2 : EUT Detailed Photographs (1) EUT Photo (2) EUT Photo Page : 1 of 7

Report No R-RFCEP02V01. Test Report MSI / MS-6837D. Date of Receipt Aug. 21, Issued Date Sep. 11, 2007