LinTronic BeoSystem control of non-b&o TV, screen or projector CINEMA MODE Updated: 190108 IR-Tx IR-Tx IR-Rx IR-Tx
The TT455-RT-238 can be your gateway to utilizing the potential of CINEMA control from your BeoSystem. When you press the CINEMA (or FORMAT + 0 on some remotes) button on your B&O remote, your BeoSystem can automate control of a projector, projector screen, shades and even lighting to give you the full cinematic experience. Lintronic provides solutions for relay controls, but you can also use the TT455-RT-238 to send out IR control of your devices when using CINEMA mode. All that you need are pinout/breakout boards and a few wires to make the connections of the pins between the breakout boards.
GO BANG & > > > >> BeoSystem control of non-b&o TV, screen or projector Controlling the TT455-RT-238 and the BeoSystem using only one IR receiver. BeoSystem DIGITAL OUTPUT 2 IR DATA INPUT RS232 EXTERNAL RECEIVER UP TO 50 METERS TT-IR-8087030 width: 7 cm TT455-RT-238 T SA LIGHT DV VTAPE RECORD 7 C 54 8 1 9 TE 2 6 3 > ME LIST EXIT ST >
Controlling the TT455-RT-238 and the BeoSystem using only one IR receiver. In Memory Map: Set the digital output 2 to Beosystem
Controlling the TT455-RT-238 and the BeoSystem using only one IR receiver. External receiver Input Aux Communication Output Output Power Power Tx (to cpu) Rx (from cpu) To computer Jack connector seen from solderside 5 4 3 2 1 9 8 7 6 C B NOTE: The digtal output 2 is as default set to 12 volt output. Must be changed to ground output. See technical manual how to solder for 5 volt pull-up. DIGITAL OUTPUT 2 IR/DATA Ground C B TO BEOSYSTEM B
When the TT-IR-8087030 IR receiver is inserted into the IR INPUT and DIGITAL OUTPUT 2 is set to BeoSystem, you should be able to monitor the IR noise/signal from the IR receiver on the digital output 2 on an oscilloscope, as shown below. External receiver Input Aux Communication Output Output Power Power 5 4 3 2 1 9 8 7 6 DIGITAL OUTPUT 2 IR/DATA Ground C B TO BEOSYSTEM B
The TT455-RT-238 may work together with a BeoSystem and convert the digital outputs into infrared or RS232 commands for a non-b&o tv, screen, projector, light system, etc. etc. The BeoSystems digital outputs are activated when the BeoSystem enters Cinema mode, and they are de-activated when the BeoSystem leaves Cinema mode. The TT455-RT-238 is easily configured to react when the digital input is activated or deactivated, or both - and will send IR or RS232 commands as instructed. BeoSystem 3 1 2 3 4 5 6 7 8 9 Cinema Control DigOut 1 DigOut 2 6 7 5 2 Digital Inputs 1 BEOSYSTEM 3 See next pages for Beosystem 4 The TT455-RT-238 will trigger on the digital signals and convert into relays, infrared or RS232 commands. 5 4 3 2 1 9 8 7 6 RS232 Tx Rx TV, screen, projector, light, etc.
This example shows how a BeoVision-7 controls a Sanyo projector (normally not supported by the BV7) when the customer activates FORMAT-0 on his BEO4. BeoSystem 3 Cinema Control 1 2 3 4 5 6 7 8 9 DigOut 1 BEOSYSTEM 3 See next pages for Beosystem 4 Tx1 DigIn1 Relays? 5 4 3 2 1 9 8 7 6 Tx2 RS232 for your light? Tx2 TT455-RT-238 Signal Converter - When Digital Output 1 from Beosystem is On, then send Power On by RS232 to Sanyo. - When Digital Output 1 from Beosystem is Off, then send Power Off by RS232 to Sanyo. 1 6 Rx 2 3 7 8 4 9 5 Optionally RS232 port 2 could control your light system? Or the digital outputs could control a couple of relays?
The TT455-RT-238 may work together with a BeoSystem and convert the digital outputs into infrared or RS232 commands for a non-b&o tv, screen, projector, light system, etc. etc. The BeoSystems digital outputs are activated when the BeoSystem enters Cinema mode, and they are de-activated when the BeoSystem leaves Cinema mode. The TT455-RT-238 is easily configured to react when the digital input is activated or deactivated, or both - and will send IR or RS232 commands as instructed. BEOSYSTEM 4 PUC 1 Out1 Out 2 2 3 4 2 Digital Inputs 1 RJ45 breakout box can be found on Amazon or Ebay The TT455-RT-238 will trigger on the digital signals and convert into relays, infrared or RS232 commands. 5 4 3 2 1 9 8 7 6 RS232 Tx Rx TV, screen, projector, light, etc.
BEOSYSTEM 4 PUC 1 2 4 RJ45 breakout box can be found on Amazon or Ebay
BEOLIVING BeoSystem OUPUT 1 OUPUT 2 6 7 5 GND 5 6 7 8 GND 12V G B A 2 1 C A R C A R C A R C A R 1 2 3 4 1 2 3 COM1 COM2 Quick-adjust the on-time for relay 3, 4, 7, 8 (default 3 seconds): - activate and hold switch 2 - count the seconds (blinks) - Release switch 2 C A R C A R C A R C A R BEOSYSTEM Cinema mode On When Digital Output 1 goes low (active), then relay 1 and relay 2 are activated (ON - no timeout). Relay 3 is activated for the programmed time (default 3 seconds). When Digital Output 2 goes low (active), then relay 5 and relay 6 are activated (ON - no timeout). Relay 7 is activated for the programmed time (default 3 seconds). Cinema mode Off When Digital Output 1 goes high (in-active), then relay 1 and relay 2 are de-activated (Off). Relay 4 is activated for the programmed time (default 3 seconds). When Digital Output 2 goes high (in-active), then relay 5 and relay 6 are de-activated (Off). Relay 8 is activated for the programmed time (default 3 seconds).
TT455-RT-238 reacts to Cinema mode on/off, controls screen up/down and projector by RS232 and 3 rd party products by IR. BeoSystem 5 6 7 9-pin SUB-D/Female Input Output Comm Output 5 1 4 2 3 9-pin SUB-D/Male IR RECEIVER STEREO-EXT-10 TT-IR-ET03 5 6 1 5 2 3 9-pin SUB-D/Female 1 2 5 2 9-pin SUB-D/Male 5 2 4 6 9-pin SUB-D/Female