REV 00 SPECIFICATIONS MODEL NO. FN070MY03 TYPE LCD MODULE, 800(RGB) * 480 PIXELS,WITH CTP Preliminary Specification Final Specification FANNAL CUSTOMER PREPARED CHECKED APPROVED APPROVED FANNAL ELECTRONICS CO., LTD
Page:2 /20 Spec No:FN070MY03 RECORDS OF REVISION REV. DATE Page DESCRIPTION OF CHANGES 00 2014.05.08 First Release
Page:3 /20 CONTENT 1. GENERAL SPECIFICATION...4 2. MECHANICAL DRAWING...5 3. INTERFACE ASSIGNMENT...6 4. ELECTRICAL SPECIFICATION...7 4.1. POWER SUPPLY...7 4.2. DC CHARACTER...7 4.3. AC CHARACTER...7 4.4. TIMING DIAGRAM OF INTERFACE SIGNAL...8 4.5. BACKLIGHT SPECIFICATION... 11 5. OPTICAL CHARACTERISTICS... 11 6. TOUCH PANEL SPECIFICATION...17 7. RELIABILITY TESTS...19 8. PACKAGE DRAWING...20 9. PRECAUTIONS...20 9.1. HANDLING...20 9.2. STORAGE...20 9.3. SAFETY...20 10. LIMITED WARRANTY...20 10.1. RETURNING LCM UNDER WARRANTY TERMS AND CONDITIONS...20
Page:4 /20 1. GENERAL SPECIFICATION 1.1. Description The FM070MY03 is a color active matrix Thin Film Transistor (TFT) Liquid Crystal Display (LCD) that uses amorphous silicon (a-si) TFT as a switching device. This model is composed of a single 7.0 (16:9) inches transmissive type main TFT-LCD panel. The resolution of the panel is 800(RGB) x 480 pixels and can display up to 16M color. 1.2. Feature -TM type for main TFT-LCD panel -24bits RGB interface -One backlight with 24 white LEDs 1.3. Application -Display terminals for digital product 1.4. General Specification No. Item Specification Unit Remark 1 LCD Size 7(digital) inch - 2 Panel Type a-si TFT active matrix - - 3 Resolution 800 (RGB) x 480 pixel - 4 Display Mode Normally white,transmissive - - 5 Display Number of 16M - - 6 Viewing Direction 6 o clock peack CR (12o clock good view) - Note 7 Contrast Ratio 500(TYP) - - 8 Luminance 360(TYP) cd/m 2-9 Module Size 164.9(W ) x 100.0(H) x 6.93(D) mm Note 10 Active Area 154.08(H) x 86.42(V) mm Note 11 Pixel Pitch mm - 12 Weight TBD g - 13 Driver IC HX8264-D05&HX8664-B - - 15 Light Source 24 LEDs White - - 16 Interface RGB 24bit - - 17 Operating Temperature -20~70-18 Storage Temperature -30~80 - Note: Please refer to the mechanical drawing.
Page:5 /20 2. MECHANICAL DRAWING 0.3±0.05 *5.5±0.1TFT FN070MY03 FANNAL ELECTRONICS CO.,LTD
Page:6 /20 3. INTERFACE ASSIGNMENT PIN NO. SYMBOL I/O FUNCTION DESCRIPTIONS 1 LED-A P Power for LED backlight (Anode) 2 LED-A P Power for LED backlight (Anode) 3 LED-K P Power for LED backlight (Cathode) 4 LED-K P Power for LED backlight (Cathode) 5 GND P Power Ground 6 VCOM P TFT Common Voltage input 7 DVDD P Power for Digital Circuit 8 MODE I DE/SYNC mode select 9 DE I Data enable signal 10 VS I Vertical sync input. 11 HS I Horizontal sync input. 12~19 B7~B0 I Blue Data Input 20~27 G7~G0 I Green Data Input 28~35 R7~R0 I Red Data Input 36 GND P Power Ground 37 DCLK I Sample Clock Input 38 GND P Power Ground 39 L/R I Left / right selection 40 U/D I Up/down selection 41 VGH P Positive Power for TFT Gate ON 42 VGL P Negative Power for TFT Gate OFF 43 AVDD P Power for Analog Circuit 44 RESET I Global reset pin. 45 NC / No connection 46 VCOM P TFT Common Voltage input 47 DITHB I Dithering function 48 GND P Power Ground 49 NC / No connection 50 NC / No connection I: input, O: output, P: Power Note 1: DE/SYNC mode select. Normally pull high. When select DE mode, MODE= 1, VS and HS must pull high. When select SYNC mode, MODE= 0, DE must be grounded. Note 2: When input 18 bits RGB data, the two low bits of R,G and B data must begrounded. Note 3: Data shall be latched at the falling edge of DCLK. Note 4: Selection of scanning mode
Page:7 /20 4. ELECTRICAL SPECIFICATION 4.1. POWER SUPPLY Item Symbol Min. Typ. Max. Unit Note Vcc 3.0 3.3 3.6 V Supply Voltage VGH 17.0 18.0 19.0 V VGL -6.6-6 -5.4 V AVDD 9.4 9.6 9.8 V VCOM VCom 3.8 4.0 4.2 V Note 1 Note 1: Please adjust VCOM to make the flicker level be minimum. 4.2. DC Characteristics Symb Item Min. Typ. Max. Unit Note ol Input signal Voltage ViH 0.7Vcc - Vcc V Note(1) ViL 0-0.3 Vcc V Current of power IDD - 7 16 ma supply IADD - 6 8 ma Note (1): HSYNC, VSYNC, DE, Digital Data 4.3. AC Characteristics
Page:8 /20 4.4. TIMING DIAGRAM OF INTERFACE SIGNAL
Page:9 /20
Page:10 /20
Page:11 /20 4.5. BACKLIGHT SPECIFICATION 5. OPTICAL CHARACTERISTICS (T a =+25, VCC=+3.3V, I B =180mA) B Item Symbol Condition Values Unit Remark Min. Typ. Max. Left θ L 60 70 - Viewing Right θ R 60 70 - CR 10 Angle Range Top Ф T 40 50 - degree Note 1,2 Botto Ф BB 50 60 - Normal Response Time T on +T off θ=ф=0-25 35 ms Note 2,3 Contrast Ratio CR Normal θ=ф=0 400 500 - - Note 2,4 Luminance L Normal θ=ф=0-360 - cd/m 2 Note 2,5 White Wx 0.25 0.30 0.35 Wy 0.28 0.33 0.38 Rx 0.55 0.60 0.65 Color Red Ry Normal 0.31 0.36 0.41 Chromaticity Gx θ=ф=0 0.31 0.36 0.41 (CIE1931) Green Gy 0.54 0.59 0.64 - Note 2,4 Blue Bx 0.11 0.16 0.21 By 0.08 0.13 0.18 Color Gamut NTSC CIE1931 45 50 - % - Luminance Uniformity Flicker U L Normal θ=ф=0 Normal θ=ф=0 70 80 - % Note 2,7 Not visible - Note 9 Crosstalk Normal θ=ф=0 Not visible - Note 10
Page:12 /20 Note 1: Definition of viewing angle range Normal line θ=ф=0 θ B θ T 12 o clock direction Ф=90 θ L θ R Ф=180 Ф=0 Active Area LCD Panel Ф=270 6 o clock direction Fig. 1 Definition of viewing angle Fig. 2 Definition of viewing angle for display Note 2: Definition of optical measurement system
Page:13 /20 The optical characteristics should be measured in a dark room with ambient temperature T a =+25. The optical properties are measured at the center point of the LCD screen after 5 minutes operation. (Equipment: Photo detector TOPCON BM-5AS Field of view: 1 /Height: 500mm.) Photo detector Normal line θ=ф=0 500mm 12 o clock direction Ф=90 Ф=180 Ф=0 Active Area LCD Panel Ф=270 6 o clock direction Fig. 3 Optical measurement system setup Note 3: Definition of response time The response time is defined as the LCD optical switching time interval between White state and Black state. Rise time (T on ) is the time between photo detector output intensity changed from 90% to 10%, and fall time (T off ) is the time between photo detector output intensity changed from 10% to 90%. White (TFT OFF) Black (TFT ON) White (TFT OFF) (Relative value) Photo detector output 100% 90% 10% 0% T on T off Fig. 4 Definition of response time
Page:14 /20 Note 4: Definition of contrast ratio Note 5: Definition of luminance Measured at the center area of the panel when LCD panel is driven at white state. Note 6: Definition of color chromaticity (CIE1931) Color coordinates measured at the center point of LCD when panel is driven at White, Red, Green and Blue state respectively. Note 7: Definition of luminance uniformity To test for uniformity, the tested area is divided into 3 rows and 3 columns. The measurement spot is placed at the center of each circle as below. L Luminance Uniformity (U L ) = L min max L-------Active area length W----- Active area width W W/6 W/3 W/3 L L/3 L/3 L/6 Fig. 5 Definition of luminance uniformity L min : The measured minimum luminance of all measurement position. L max : The measured maximum luminance of all measurement position. Note 9: Definition of Flicker
Page:15 /20 Flicker is the pattern usually used to describe the visual sensation produced by a rapidly varying light intensity. There should be no visible flicker in normal direction of the display when the following figure are loaded. The figure is composed of interlaced black and white lines. Fig.6 Flicker checker pattern Note 10: Definition of crosstalk There should be no visible in normal direction of the display when the following figures are loaded. Fig.7 Crosstalk checker pattern
Page:16 /20 6. TOUCH PANEL SPECIFICATION 6.1. Feature -7" Projective capacitive touch panel -IC FocalTech FT5316 -True Multi-touch with up to 5 Points of Absolution X and Y Coordinates 6.2. General Specification No. Item Specification Unit Remark 1 CTP Size 7 inch - 2 Panel Type Glass Cover+Glass Sensor - - 3 Resolution 800 x 480 pixel - 4 Module Size 164.50(W ) x 99.60(H) x 1.83(D) mm Note 1 5 Active Area 156.48(H) x 88.32(V) mm Note 1 6 Surface Hardness 6H - - 7 Transparency 80%min - Note 2 8 Driver IC FT5316 - - 9 Interface I2C - - 10 Support Points 5 - - 11 Rate 20-100 Hz - 12 Power supply 2.8-3.3 V - 13 Operating current Normal mode 7.2(Typ.) ma - Green mode 3(Typ.) ma - Sleep mode 0.07-0.12 ma - 14 Operating Temperature -20~70-15 Storage Temperature -30~80-16 ESD Note1: Please refer to the mechanical drawing. Note2: Wave Length 550nm. Note3: Touch Panel Surface. Air ±8 KV Note3 Contact ±4 KV Note3 6.2. FPC PIN Assignment PIN NO. SYMBOL FUNCTION DESCRIPTIONS 1 VCC Analog power supply(2.8-3.3v) 2 WAKE Wake signal 3 INT Interrupt signal(1.8v) 4 SCL I2C clock(1.8v) 5 SDA I2C data(1.8v) 6 GND Ground
Page:17 /20 6.3. Serial Interface FT5316 supports the I2C interfaces, which can be used by a host processor or other devices.the I2C is always configured in the Slave mode. The data transfer format is shown in Figure 2-4.
Page:18 /20 6.4. Electrical Specifications Absolute Maximum Ratings
Page:19 /20 7. RELIABILITY TESTS ITEM CONDITION CRITERION Operating Temperature Test Storage Temperature Test High Temp &High Humidity Thermal Shock Test Vibration Test Package Drop Test Electro Static Discharge High Temperature: +70±2 ºC,96hrs Low Temperature: -20±2 ºC, 96hrs High Temperature: +80 ±3ºC, 120hrs Low Temperature: -30±3ºC, 120hrs 50 ºC, 90RH, 96hrs -20 ºC (0.5 hrs) +70 ºC(0.5 hrs) 10 cycles Package Operating Time: 60 minutes exposure for each Y direction Sweep Frequency:10~55Hz (1 min) Amplitude: 1.5mm Speed:20m/s2 Height :1.0m (Weight 10kg); 60cm(Weight 10kg) 1 corner,3 edges,6 surfaces ± 2KV, Human Body Mode, 100pF/1500Ω ± 8KV, Air Mode, 100pF/1500Ω No defects in display and operational functions No defects in display and operational functions No defects in display and operational functions No defects in display and operational functions No defects in display and operational functions No defects in display and operational functions No defects in display and operational functions NOTE: 1) The samples must be free from defect before test, must be restored at room condition at least for 2 hours after reliability test before any inspection. 2) Before test the function of TP, the sample must be placed in room temperature for 24hrs after RA test. 8. PACKAGE DRAWING TBD 9. PRECAUTIONS 9.1. HANDLING 9.1.1. Polarizer Cleaning, Petroleum ether (or N-hexane) is recommended for cleaning the front/rear polarizers and reflectors, acetone, toluene and ethanol are not allowed to avoid damaging the surface. 9.1.2. Body grounding, must wear Anti-ESD wrist strap while pick up LCDs. 9.1.3. FPC Soldering, less than 300 /3S, solder must be grounding on grounding bench. 9.1.4. If use electric Screwdriver to do assembly, screwdriver must be grounding.
Page:20 /20 9.2. STORAGE 9.2.1. Keep in a sealed polyethylene bag. 9.2.2. Keep in a dark place. 9.2.3. Keep in temperature between 0 and 35. NOT allowed at 70 for more than 160 Hours, or at -20 for more than 48 Hrs. 9.3. SAFETY If liquid crystal leak out of a damaged glass cell, DO NOT put it in your mouth or touch eyes, if the liquid crystal touch your skin or clothes, please wash it off immediately using soap and water. Tel:+86-571-8516 1516 FAX:+86-571-88801847 Email:Sales@fannal.com