7050/7050/70505/7055 Digital Oscilloscopes DL540/DL540L/DL50/DL50L FUNCTIONS SIGL OBSERVATION USING LONG MEMORY Capturing Signals Using Long Memory for Accurate Waveforms The DL50/DL540 can continuously capture signals using a record length of up to 0k words, and the DL540L/DL50L using a record length of up to 00k words. Within the desired observation period, the DL50/DL540 can thus capture signals at a time resolution (sampling rate) of 0 times that for signals captured using a record length of k word, and the DL540L/DL50L at a time resolution of 00 times. (You can use a longer record length when capturing a single-shot signal, or when using the roll mode.) DL540(7050) 5 68 95mm 6kg (8-/ 0-9/6-5/8" 3. lbs) DL540L(7050) 5 68 95mm 6kg (8-/ 0-9/6-5/8" 3. lbs) Safety Standards; EN600 EMI Standard; EN550 Group Class A Immunity Standard; EN5008-: 995 Observation using a 0-kword record length (signal capture using DL540) Observation using a -kword record length (signal capture using DL00) The DL500 Series Digital Oscilloscopes are high performance personal digital oscilloscope in a compact and light body. FEATURES Full range 4 channels (DL540/DL540L) Max. (8 bits) 50 MHz analog bandwidth Max. M words (DL540L) M words (DL50L) 0k words (DL540) 0k words (DL50) Approx. 6 kg (DL540L/DL540/DL50L/ DL50) Footprint smaller than A4 Built-in 3.5-inch FDD (option) Zoom Function Displays Eight Traces Simultaneously, Zooming in Quickly and Easily on Waveform Details Zooming is an important function in a digital oscilloscope with a long record length. The DL500 series inherits the popular intuitive, high-speed zooming function of the DL4000 series. The DL500 series eliminates problem of which trace to assign the zoom trace to. This scope allows you to display the captured trace and the zoomed trace at the same time. DL500 SERIES Basic Specifications Interface Functions Number of input channels Max. Sampling rate Max. record length Frequency bandwidth Advanced trigger 3.5 inch FDD box control connector Centronics RS-3-C GP-IB Snap shot History memory Sequential store DL540L 4 M word 50MHz DL540 4 0k word 50MHz DL50L M word 50MHz * * * DL50 0k word* 50MHz * * * * : In Roll mode. * : Varies depending on the model.
DL540/DL540L/DL50/DL50L Recall Any Waveform with The History Memory Function (DL540/DL540L/DL50L only) With a conventional digital oscilloscope, the contents of the memory are updated at every trigger. So once a waveform is updated, there is no way to bring the previous waveform back. However, the history memory function of the DL540/ DL540L/DL50L stores the last 00 displays. A SINGLE OSCILLOSCOPE TO PERFORM EVERYTHING, FROM PROCESSING TO RECORDING OF THE CAPTURED SIGL (al built-in printer is needed to print captured waveforms) Automatic Waveform Parameter Measurement Function With this function you can automatically measure the maximum voltage, frequency and other parameters of a waveform. Roll Mode for Maximum Sampling Speed of 00 ks/s Roll mode is ideal for observing low frequency signals of around 0 Hz, which is difficult to do with a conventional analog oscilloscope. The roll mode allows a maximum sampling speed of 0 ks/s for the DL50/DL540, or 00 ks/s for the DL540L/DL50L. Compiling a Report Using a Hard Copy/Image File By using the built-in 3.5-inch FDD that supports three MS-DOS modes, you can save waveform data, panel setting information and hard copy images from the screen. You then simply import the hard copy of the screen directly into a word processor document when writing a report or paper using a PC with Windows. Screen Update Speed Independent of Number of Traces Displayed or Waveform Processing Type As shown in the figure below, it is easy to overlook an irregular event if the digital oscilloscope has a slow screen update speed. With most digital oscilloscopes, the screen update speed falls as the number of waveforms displayed is increased, or when signal processing such as automatic measurement of the waveform parameters is taking place. The DL500 Series has been designed primarily for measuring waveforms; hence signals are measured without reducing the screen update speed even when the number of waveforms displayed is increased or signal processing is added. Actual signal Real-time Printing Function Captures 0 ns Pulse Signals The real-time printing function continuously records low-speed signals to the built-in thermal printer. The chart speed runs at up to 6.7 mm/s, and the speed can be changed by setting the time axis.
DL540/DL540L/DL50/DL50L Short Copy Function Outputs a Screen Hard Copy in Just 0 Seconds This function outputs a hard copy of a waveform displayed on the screen to the built-in printer. You can even attach to the screen hard copy the panel setting information that was used to capture the waveform. OR Trigger ( for DL540/DL540L Only) A trigger occurs when any one of the trigger conditions which are set for each channel is satisfied. Long Copy Function Records Signals in Expanded Form after Storing Them in Long Memory With the long copy function of the DL500 Series, you can print out signals in expanded form after first storing them in the memory. When using the zoom function, an expanded screen can only be displayed one page at a time on the CRT. By using the Long Copy function, you can print an expanded diagram containing many pages of the expanded waveforms. A WEALTH OF TRIGGER FUNCTIONS Window Trigger A trigger occurs when the incoming signal crosses one of the upper or lower level thresholds which you set in advance. So you can capture signals even if you don t know the polarity of the noise component on the DC line. Pulse Width Trigger, Timeout ( for DL540/DL540L Only) A trigger occurs when the pulse width becomes narrower or wider than the defined width. In the case of the timeout trigger, a trigger occurs when the next signal is not detected within a certain time. Trigger point TV Trigger You can apply a trigger to NTSC, PAL and HDTV signals and specify the number of lines of the signal to be captured. (The HDTV trigger is supported only by the DL540/DL540L.) Pattern Trigger ( for DL540/DL540L Only) By assigning High, Low, or Don t Care to each channel, you can trigger on a combination of signals. You can also assign the signal in one channel as the trigger source.
DL540/DL540L/DL50/DL50L SPECIFICATIONS Vertical section Number of input channels: 4 (DL540/DL540L); (DL50/DL50L) Vertical resolution: 8 bits (normal) (5LSB/div) 9 bits (smoothing) bits (after averaging with 56 weight) Max sampling rate: Normal (when half of the number of available channels are in use) 00 MS/s (when all channels are in use) Equivalent time 0 GS/s Effective storage frequency (-3 db): Repetitive waveform DC to 50 MHz * Single shot waveform DC to 80 MHz * (When half of the number of available channels are in use) DC to 40 MHz * (When all channels are in use) Sensitivity: mv/div * 3 to 5 V/div (DL540/DL540L) mv/div to 5 V/div (DL50/DL50L) DC accuracy * 4 : 00 mv/div ±(.5% of 8 div + LSB) mv/div ±(5% of 8 div + LSB) Other ranges ±(.5% of 8 div + LSB) Offset voltage accuracy: m to 50 mv/div ±(.5% of set value + 0. mv) 00 m to 500 mv/div ±(% of set value + mv) to 5 V/div ±(.5% of set value + 0 mv) Interchannel isolation: Max input voltage: Input impedance: Input coupling: Horizontal section -40 db (typical value * 5 in the same range) 50 V (DC + AC peak) ( khz max) (CAT I & II, 77 Vrms) MΩ±.5% (approx. 5 pf) AC/DC/GND Sweep time: 5 ns/div to 50 s/div Time axis accuracy: ±(0.0% + 500 ps)* 6 Max record length (DL540L): M words ( channels use) M word (3 or 4 channels use) Max record length (DL50L): M words ( channel use) 400k word ( channels use) Max record length (DL540): 0k words ( channels use) 56k words (3 or 4 channels use) Max record length (DL50): 0k words (roll mode) 0k words (other mode) External clock input: (DL540/DL540L): EXT CLOCK IN input 40 Hz to 5 MHz * 7 CH4 input * 40 Hz to 80 MHz * 7 (DL50/DL50L): 40 Hz to 80 MHz Trigger Mode: Source: Slope: Coupling: Sensitivity: Type: External trigger input (DL540/DL540L): Range Level Frequency range (DL50/DL50L): AUTO/AT-LVL/NORMAL SGL(S) * 9 /SGL(L)* 9 SINGLE * 0 /N-SGL: Sequential store * CH /CH /CH3 * /CH4 * /EXT /LINE Rise/Fall/Both AC/DC/HFRej div p-p (DC to 50 MHz) Edge TV * 8 NTSC/PAL/HDTV * Window * 8 OR (option * ) Pattern (option * ) Pulse width (option * ) ±6 V.5 V/ 0.5 V DC to 5 MHz Range ±0 V/± V Level Range ±0 V range: ±0 V ± V range: ± V Resolution ±0 V range: 40 mv ± V range: 4 mv Input sensitivity (DC to 00 MHz) ±0 V range: Vp-p ± V range: 00 mvp-p Display CRT: 7-inch, raster scan, amber (540 43 dots) Number of displayed traces: Max 8 traces (zoom mode) (DL540/DL540L) (4 captured + 4 magnified) traces Max 6 traces (zoom mode) (DL50/ DL50L) ( captured + magnified + Math) traces Extension functions Computation: +,, x, FFT (000-point power spectrum) GO/NO-GO function: Zone: Up to 4 traces Parameter: Up to 4 parameters Automatic waveform parameter measurement: Up to items for each trace. Parameters for all traces can be measured simultaneously, and the result of automatic measurement displayed. Up to 4 items can be displayed. Image format saving: HP-GL, PostScript, TIFF, and BMP formats Snapshot: By pressing the snapshot key, an infinite number of waveforms can be kept on the CRT screen. Accumulation: 0. to 60 s, INFINITE (infinite period) Communication GP-IB interface Electrical and mechanical specifications: Conform to IEEE st d. 488-978 Protocol: Conforms to IEEE st d 488.-987 RS-3-C interface [RS-3-C interface unit (optional accessory) required for use with the DL540 and the DL540L] Baud rate: 75, 50, 300, 600, 00, 400, 4800, 9600, 900 bps Centronics interface [ for the -C3 model of the DL50 and the DL50L] Supported printer commands: ESC/P, LIPS3, PC-PR0, PCL5 SCSI interface [SCSI interface unit (optional accessory) required for the DL540 and the DL540L. for -C4 model of the DL50L.] Supported SCSI devices and conditions HD drive: Drive formattable by the EZ-SCSI MO drive: Up to 640MB type which is formattable by the EZ-SCSI Zip drive: Iomega Zip drive compatible Signal input/output TRIG OUT * : TTL level GO/NO-GO evaluation output * : TTL level (from option box control connector) GO/NO-GO operation condition output * : TTL level (from option box control connector) Calibration output: khz, Vp-p, square wave 3.5-inch FDD Types of supported disks: Format: (option) Printing method: Dot density: Paper width: Realtime printing: 640 KB, 70 KB,. MB,.44 MB MS-DOS Thermal line dot method 6 dots/mm mm Max 6.7 mm/s chart speed ( from a time axis range of 500 ms/div and slower) General specifications Operation temperature range: 5 to 40 C Operation humidity range: 0 to 85% RH (when not using the printer) 35 to 85% RH (when using the printer) Supply voltage: 00 to 0 V AC/ 0 to 40 V AC DL540/DL540L Automatically switched DL50/DL50L Select from the above Supply frequency: 50/60 Hz Power consumption: 80 VA max External dimensions: 5(W) 68(H) 95(D) mm (Excluding projections) Weight: Approx. 6 kg (DL540/DL540L/DL50/DL50L main unit only) Screen update speed channel in use: Max 60 screens/s All channels in use: Max 60 screens/s
DL540/DL540L/DL50/DL50L * : Between 5 V/div and 0 mv/div ranges. For 5 mv/div: DC to 80 MHz. For mv/div and mv/div: DC to 0 MHz. * : Between 5 V/div and 5 mv/div ranges. For mv/div and mv/div: DC to 0 MHz. * 3 : mv/div is realized by zooming of mv/div. * 4 : Standard operating conditions (3± C, 55±0% RH). After 30 minutes warmup, and after calibration. * 5 : A typical value is a representative or average value. It is not a strictly guaranteed value. * 6 : Standard operating conditions (3± C, 55±0% RH). After 30 minutes warmup. * 7 : Continuous clock signal only. * 8 : Supported by CH only. * 9 : DL540 only. * 0 : DL540L/DL50/DL50L only. * : DL540/DL540L only. * : DL540/DL540L/DL50L only. Accessories (optional) Code 50Ω terminator 700976 Carrying case 70095 RS-3-C unit 70097 TV signal output unit 70098 SCSI interface unit 700930 Through type 340(W) 90(H) 5(D) mm Exclusively for DL540/DL540L Exclusively for DL540/DL540L* Exclusively for DL540/DL540L* Order Q ty * : For the DL540, the firmware version.0 or later is required. * : For the DL540 and the DL540L, the firmware version.0 or later is required. Standard Accessories No. Power cable. Probe Set of manuals. Soft case (for storing probes, etc.) Front cover (70096) Quantity Carrying case RS-3-C unit.. TV signal output unit SCSI interface unit AVAILABLE MODELS DL540/DL540L Model Suffix code 7050 7050 Power - voltage -5 Power cable s -D -F -Q -R /B5 /F /E DL540 Digital Oscilloscope DL540L Digital Oscilloscope 00 to 0 V AC 0 to 40 V AC UL, CSA standard VDE standard BS standard SAA standard Enhanced trigger Two additional 700998 probes Spare Parts Roll paper for printer 50 MHz passive probe Soft case Front cover Printer connecting cable DIMENSIONS Code B9850NX 700998 B998EZ 70096 B996TB 30 m (one roll/unit) 0 MΩ (0:),.5 m (/unit) For storing probes, etc. For protecting the CRT and the front panel m (exclusively for DL50) 3 95 (8.39) (.6) Order Q ty 5 Unit: mm (inch) DL50 / DL50L Model Suffix code 70505 7055 Power - voltage -5 -D -F Power cable -Q -R -C -C Communication -C3 -C4 s /B5 * : for the DL50L only. DL50 Digital Oscilloscope DL50L Digital Oscilloscope 00 to 0 V AC 0 to 40 V AC UL, CSA standard VDE standard BS standard SAA standard GP-IB interface RS-3-C interface GP-IB & Centronics interface GP-IB & SCSI interface* 5 (8.47) 68 (0.55) 8 (0.3)