New! HR series Distinctive features and specifications High reliability, long life HR-A-R Sealed to IP68 Backlighting option EMI/RFI shielding Other detent options on request Patented solution ENVIRONMENTAL SPECIFICATIONS Electronics sealed to IP68 according to IEC 69 Shock resistance : g during ms Vibration resistance : -Hz - g according to IEC -, test 6d Salt spray : IEC -6, test f Operating temperature : - C to +7 C Storage temperature : - C to +8 C EMI/RFI shielding : IEC 6-- and ISO - (V/m) ESD discharges : 6KV according to EN 6-- ELECTRICAL SPECIFICATIONS Hall effect sensor Supply voltage : VDC +/- V Reverse polarity : -V max. Overvoltage : +V max. Return to center voltage (no load) : +/-,V Consumption : ma max. (single output) ma max. (dual output) LED supply : 6VDC ma GENERAL SPECIFICATIONS APEM SAS patented design Mechanical operating angle : +/- (versions S/G/L) +/- (version K) Sprung to center Operating force at center: N +/- N (without detent position) N +/- N (with detent position) Mechanical life : million cycles (without detent) MATERIALS Wheel : polyamide with colouring Support : polyamide, black Electronics sealing : epoxy Connector : polyester (Molex 7) Multiwire lead AWG8 Tolerance : The general tolerance for dimensions in this brochure is ±, (.). Dimensions, specifications and data shown in this brochure are subject to change without notice. APEM www.apem.com
HR series Overview New! HR SERIES Actuator styles Panel mounting S G K L Wheel with tab Reversed wheel with tab Wheel with tabs Wheel without tab Rear Backlighting Wheel colours Linear output options Mechanical functions Yes No Blue B Dark blue Black Green Yellow 6 Red 7 White 9 Orange A Single - /V B Single - /V C Dual - /V D Dual - /V E Inverse dual - /V F Inverse dual - /V Sprung to centre without centre detent Sprung to centre with centre detent Other detent options: on request. ABOUT THIS SERIES On the following pages, you will find successively : - model structure of switches - options in the same order as in above chart Dimensions : first dimensions are in mm while inches are shown as bracketed numbers. NOTICE : please note that not all combinations of above numbers are available. Refer to the following pages for further information. Mounting accessories : standard hardware supplied : self-tapping screws DELTA PT x8 for plastic. Packaging unit : pieces www.apem.com APEM
New! HR series Actuator styles Wheel with tab - version S HRS Reversed wheel with tab - version G HRG Wheel with tabs - version K HRK Wheel without tab - version L HRL APEM www.apem.com
HR series Options New! EXAMPLE OF MOUNTING BACKLIGHTING Yes No WHEEL COLOURS : Blue - B : Dark blue - : Black - : Green - : Grey - : Yellow - 6 : Red - 7 : White - 9 : Orange www.apem.com APEM
New! HR series Options LINEAR OUTPUT OPTIONS output output,,,, A Single - /V B Single - /V,,,, C Dual - /V D Dual - /V,,,, E Inverse dual - /V F Inverse dual - /V Note: The output voltage cannot be superior to the power supply voltage. For /V versions, the power supply should not be lower than V. APEM www.apem.com
HR series Options - Connections New! MECHANICAL FUNCTIONS Sprung to centre without centre detent Sprung to centre with centre detent Other : on request. CONNECTIONS Single output without backlighting Power supply: +VDC V Red 6 Output 7 Ground V Black 6 7 Single output with backlighting Power supply: +VDC V Red LED + Yellow LED - Blue Output White Ground V Black Dual output without backlighting 6 7 Power supply: +VDC V Output Output Ground V Red Green White Black 6 7 Dual output with backlighting Power supply: +VDC V Red LED+ Yellow LED- Blue Output Green Output White Ground V Black TRAVEL Wiring harness with multiwire lead AWG8. Length mm TRAVEL HR- A- R 6 www.apem.com APEM