Linear LED strips on a flexible polyimide circuit board, mounted onto a 3M thermal dissipation tape, binning according to SDCM3, CRI>80, 24V DC. Equipped with a constant current source for longer maximum runs with constant luminous flux. Discharge protection +- 2,000Volt, lifetime of LM80>60,000 hours, dimming with most common protocols (0-10Volts, TRIAC), beam angle=120, dimensions (wxh) = 1/3 x 1/16. From 75-893 lm/ft. ip66 BILTON helped invent a revolutionary new technology to create IP66 outdoor tape light (damp/wet location). The strips are not coated in silicone but with a specialized hydrophobic, plasma-enhanced, very thin film. This coating is not only extremely durable but features: 100% moisture protection No lumen loss (silicone coatings ca. 30%) No heat increase within the tape, which has negative effects on longevity (silicone coatings do not properly dissipate heat)very good UV protection and therefore no shift in color temperature, which typically occurs with silicone coatings Tape Light Output IP Rating Color Temp Ordering Code L90 = 90 lumens/ft L180 = 180 lumens/ft L270 = 270 lumens/ft L400 = 400 lumens/ft L610 = 610 lumens/ft L910 = 910 lumens/ft IP66 = Outdoor CT27 = 2700k CT30 = 3000k CT40 = 4000k CT35 = 3500k Example: L90IP00CT27 (90 lm/ft, IP00, 2700K) RGB = Color Changing IP66 = Outdoor None TW = Tunable White IP66 = Outdoor CT27-40 = 2700k-4000k Technical Information Output L90 L180 L270 L400 L610 L910 RGB Tunable White LEDs/ft 36 36 36 36 36 36 18 72 Lumens/ft @ 4000K 90 180 270 400 610 910 Max 110 460 Consumption (watt/ft) 0.73 1.62 2.5 3.66 5.85 8.78 2.2 4.12 Efficacy @ 4000k (lm/watt) 123 111 108 109 104 104 111 CRI >80 >80 >80 >80 >80 >80 >80 Voltage 24 24 24 24 24 24 24 24 Maximum run length 75 47 35 25 18 15 20 30 Customization increment 2" 2" 2" 2" 2" 2" 4 2 Pg. 1
Power Supply Model Power IP Input Output Dimension (Inch) LxWxH TR = Non-Dimming DTR =Dimming (0-10V) DTR FP = Dimming (Forward Phase) 50 = 50 watt 75 = 75 watt 100 = 100 watt 150 = 150 watt 12 = 12 watt 16 = 16 watt 25 = 25 watt 35 = 35 watt 20 = 20 watt 35 = 35 watt 60 = 60 watt 100 = 100 watt 16 = 16 watt 25 = 25 watt 40 = 40 watt 60 = 60 watt 90 = 90 watt 100 = 100 watt 120 = 120 watt 150 = 150 watt 185 = 185 watt 240 = 240 watt 320= 320 watt 600 = 600 watt 20 = 20 watt 40 = 40 watt 60 = 60 watt 75 = 75 watt 96 = 96 watt Power Supply Ordering Code Customization IP00 88-264V IP42 90-264V IP67 90-264V 24V IP67 90-305V 24V IP67 120V 24V 3.90 X 3.82 X 1.42 5.08 X 3.82 X 1.50 6.26 X 3.82 X 1.50 7.84 X 3.85 X 1.50 3.03 X 1.57 X 1.14 3.03 X 1.57 X 1.14 3.31 X 2.24 X 1.16 3.31 X 2.24 X 1.16 4.65 X 1.38 X 1.02 5.83 X 1.57 X 1.18 6.40 X 1.67 X 1.26 7.48 X 2.05 X 1.46 5.83 X 1.57 X 1.26 5.83 X 1.57 X 1.26 6.40 X 1.70 X 1.26 6.40 X 1.70 X 1.26 6.34 X 2.40 X 1.42 8.66 X 2.68 X 1.53 8.66 X 2.68 X 1.53 8.97 X 2.68 X 1.58 8.97 X 2.68 X 1.58 9.88 X 2.68 X 1.58 9.92 X 3.54 X 1.72 11.02 X 5.67 X 1.91 Model Power IP Description TR 50 IP00 Non-Dimming, 50 watt, IP00, 88-264V output, 24V input DTR 16 IP67 0-10V Dimming, 16 watt, IP67, 90-305V output, 24V input DTR-FP 20 IP67 Forward Phase-Dimming, 20 watt, IP67, 120V output, 24V Code Description Customization T20-CUST Tapelight Customizing Cut tape to exact length (2 increments) TL20-CUST Tapelight Customizing + Lead Wires Cut tape to exact length + solder 4 lead wire E20-CUST Extrusion Customizing E20-CUST-C E20IP68-1-CUST E20IP68-3-CUST E20IP68-5-CUST Extrusion Customizing Color Extrusion Customizing IP68 for 1-2 feet Extrusion Customizing IP68 for 3-4 feet Extrusion Customizing IP68 for 5-6 feet Cut tape & extrusion to exact length, installing tape, add strain relief, and solder 4 lead wire Pg. 2
Connectors CON-S Splice connector CON2-JC Jumper Cable with 2 cable CON20-JC Jumper Cable with 20 cable CON20-PF Power feed for white tapelight with 20 cable CON20RGB-PF Power feed for RGB tapelight with 20 cable Pg. 3
Compatibility Table Cross Section L90 90 lm/ft L180 180 lm/ft L270 270 lm/ft L400 400 lm/ft L610 610 lm/ft L910 910 lm/ft RGB Tunable White CT01 CT02 Surface Mount CT06 Closet Rod DT01 Trimless UT01 Walkover VT01 Suspended WT02 45 Big XT01 XT02 Surface Mount YT01 YT02 Surface Mount YT04 45 Small YT05 Perimeter YT06 Two Sided YT07 Pendant YT08 Flangeless YT09 Flexible X X X X X X X X X X X X X X X X X X X X X X X X X Pg. 4
: 78 3 4 in standard length; can be cut to any length by factory or field cut; mounting clips available and recommended; extrusions are anodized and can be used outdoors L x W x H (inches) Cross Sections CT01 Extrusion 78 ¾ x 45 64 x 13 64 CT01 + CT99-DL Drop Lens CT01 + CT99-L60 60 Lens CT01 + CT99-AL Asym.l Lens CT02 Surface Mounted Extrusion 78 ¾ x 1 2 x 13 64 CT02 + CT99-DL Drop Lens CT02 + CT99-L60 60 Lens CT02 + CT99-AL Asym. Lens CT06 Closet Rod Extrusion 78 ¾ x 19 32 x 1 1 32 CT06 + CT99-DL Drop Lens CT06 + CT99-L60 60 Lens CT06 + CT99-AL Asym. Lens UT01 Walk-Over 78 ¾ x 1 x 55 64 UT01 + UT01-SL Satined Lens VT01 Suspended Extrusion 78 ¾ x 31 32 x 23 64 VT01 + VT01-SL Satined Lens Ɵ 31 32 Pg. 5
: 78 3 4 in standard length; can be cut to any length by factory or field cut; mounting clips available and recommended; extrusions are anodized and can be used outdoors L x W x H (inches) Cross Sections WT02 45 Big Extrusion 1 11 32 in x 1 11 32 in WT02 + WT02-SL XT01 Extrusion 78 ¾ x 1 3 16 x 49 64 XT01 + XT99-DL XT01 + XT99-CL XT01 + XT99-SL XT01 + XT99-35L 35 lens XT02 Surface Mounted Extrusion 78 ¾ x 29 32 x 33 64 XT02 + XT99-DL XT02 + XT99-CL XT02 + XT99-SL XT02 + XT99-35L 35 lens YT01 Extrusion 78 ¾ x 31 32 x 23 64 YT01 + YT99-DL YT01 + YT99-CL YT01 + YT99-SL YT02 Flush Mounted Extrusion 78 ¾ x 11 16 x 11 32 YT02 + YT99-DL YT02 + YT99-CL YT02 + YT99-SL YT04 45 Small Extrusion 78 ¾ x 11 16 x 11 16 YT04 + YT99-DL YT04 + YT99-CL YT04 + YT99-SL Pg. 6
: 78 3 4 in standard length; can be cut to any length by factory or field cut; mounting clips available and recommended; extrusions are anodized and can be used outdoors L x W x H (inches) Cross Sections YT05 Perimeter Extrusion 78 ¾ x 1 7 64 x 1 7 64 YT05 + YT99-DL YT05 + YT99-CL YT05 + YT99-SL YT06 Two-Sided Extrusion 78 ¾ x 2 11 64 x 47 64 YT06 + YT99-DL YT06 + YT99-CL YT06 + YT99-SL YT07 Direct-Indirect Extrusion 78 ¾ x 11 16 x 1 YT07 + YT99-DL YT07 + YT99-CL YT07 + YT99-SL YT08 Pocket Extrusion 78 ¾ x 3 4 x 3 3 16 YT08 + YT99-DL YT08 + YT99-CL YT08 + YT99-SL YT09 Flexible Extrusion 78 ¾ x 11 16 x 31 64 YT09 Pg. 7