aflat-series Flat Panel Controller CRTtoLCD-71
Contents 1. GENERAL INFORMATION AND NOTES... 2 1.1 User Information... 2 1.2 Trademarks... 2 1.3 General... 2 1.4 Warranty... 3 2. INTRODUCTION... 4 3. TECHNICAL INFORMATION SUMMARY... 5 4. CONFIGURATION... 7 4.1 Backlight adjust JP600... 7 4.2 Backlight-ON JP601... 7 4.3 Backlight adjust level JP602... 8 4.4 Backlight voltage JP1500*... 8 4.5 Panel voltage JP1501... 8 4.6 Display port power JP500... 8 5. CONNECTORS... 9 5.1 S-Video Input CN300*... 9 5.2 Composite video input CN301*... 9 5.3 YUV analog input CN302 (optional)... 10 5.4 VGA/RGB analog Input CN303 (optional)... 10 5.5 DVI-I input connector CN400... 10 5.6 Display Port connector CN500... 11 5.7 JILI44-Interface CN600*... 12 5.8 JILI40-Interface CN601... 12 5.9 JILI30-Interface CN603... 13 5.10 Backlight Connector CN602... 13 5.11 Audio input/output CN700*... 13 5.12 IR input CN800... 14 5.13 OSD keypad connector CN802... 14 5.14 ADC Input Connector CN900 (Light Sensor Input). 14 5.15 GPIO Connector CN901... 14 5.16 RS232 Serial OSD connector CN1300... 15 5.17 DC Power Supply 4-Pol. CN1500... 15 5.18 DC Power Supply DC-Jack CN1501... 15 6. ON SCREEN DISPLAY... 16 6.1 OSD Description... 17 7. TECHNICAL SPECIFICATIONS... 24 7.1 Supply Voltage and Current... 24 7.2 Temperature... 25 7.3 Mechanical Diamensions... 25 8. SUPPORTED VIDEO MODES... 26 Contents
9. LAYOUT / SCHEMATICS... 27 9.1 Board... 27 9.2 OSD Panel... 28 10. TECHNICAL SUPPORT... 29 11. REVISION HISTORY... 30 Contents
1. General information and notes 1.1 User Information Copyright 2015 by. In this document will also be referred to by the short form ecount. The information in this document has been carefully checked and is believed to be accurate and reliable. However, no responsibility is assumed for inaccuracies. Furthermore, ecount Technology GmbH reserves the right to make changes to any portion of this manual to improve reliability, function or design. does not assume any liability for any product or circuit described herein. 1.2 Trademarks AT and IBM are trademarks of International Business Machines. XT, AT, PS/2 and Personal System/2 are trademarks of International Business Machines Corporation. Microsoft is a registered trademark of Microsoft Corporation. Intel is a registered trademark of Intel Corporation. All other products and trademarks mentioned in this manual are trademarks of their respective owners. The reproduction, transmission or use of this document or its contents is not permitted without expressed written authority. Offenders will be liable for damages. All rights created by patent grant or registration of a utility model or design, are reserved. 1.3 General For the circuits, descriptions and tables indicated no responsibility is assumed as far as patents or other rights of third parties are concerned. The information in the Technical Descriptions describes the type of the boards and shall not be considered as assured characteristics. The reproduction, transmission or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. General information and notes 2
1.4 Warranty Each board is carefully and thoroughly tested before being shipped. If, however, problems should occur during the operation, please check your user specific settings of all boards included in your system. This is often the source of the fault. If a board is defective, it can be sent to your supplier for repair. Please take care of the following steps: - The board returned should correspond to the factory default settings since a test is only possible under these settings. - In order to repair your board as fast as possible, we require some additional information from you. Please fill out the attached Repair Form and include it with the defective board. - If possible, the board will be upgraded to the latest version without additional cost. - Upon receipt of the board, please be aware that your user specific settings are changed during the test. Within the guarantee, the repair is free as long as the guarantee conditions were kept. If no fault has been found, you will be charged with the test cost due to the high test expenditure. Repairs outside of the guarantee will be charged. This product is warranted against defects in material and workmanship for our guaranteed warranty period from the date of shipment. During the warranty period, will, at its option, either repair or replace products which prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by. The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance or handling by buyer, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper installation or maintenance. will not be responsible for any defects or damages due to a faulty product other than the products supplied by ecount Technology GmbH. General information and notes 3
2. Introduction The CRTtoLCD-71 is a highly integrated TFT panel interface controller, which allows an easy adaptation of standard video input sources like S-video, composite video, DVI or analog RGB to a digital TFT panel. The CRTtoLCD-71 only needs one single 12V power supply and incorporates all needed functionality to build up a full featured TFT monitor. The card generates the necessary power sequencing for the flat screen. The highly flexible architecture of the CRTtoLCD-71 panel interface allows adapting nearly any available TFT panel. Therefore a variety of panel adapters and programming are available on request. Introduction 4
3. Technical Information Summary FLEXIBLE DIGITAL AND ANALOG CAPTURE Integrated dual 10-bit triple ADCs with capture up to 205 MHz Input resolution support up to UXGA@75 Hz/WUXGA@60 Hz Composite-Sync and Sync-on-Green (SOG) support Instant Auto for automatic phase and clock adjustment 4:4:4/4:2:2/CCIR656/601 30/24/16/8-bit digital input port INTEGRATED HDMI 1.3 RECEIVER Integrated multi-mode HDMI 1.3 Front-end multiplexer supports two physical input ports 1080p HDMI capture support HDCP 1.2a content protection with integrated key storage xvycc support based on IEC61966-2-4 color standard Deep Color and Wide Gamut support: 12-bit HDMI input at YCC 4:4:4 INTEGRATED 3D VIDEO DECODER Single 3D Adaptive Comb Filter for Luma Chroma separation Supports Composite, S-Video, and Component SD and HD video input signals Macrovision b and VCR trick mode support INTEGRATED DISPLAYPORT 1.1 RECEIVER DisplayPort interconnectivity provides very high bandwidth compared to conventional digital interfaces DisplayPort link comprising of 4 main lines and 1 auxiliary channel WUXGA capture support INTEGRATED AUDIO PROCESSING 2 Stereo (L/R) analog inputs Additional and separate audio inputs for HDMI SPDIF Outputs include 2 analog DACs and SPDIF Worldwide multi-standards audio support Integrated I2S Audio Delay to exact audio and video synchronization Supports 5.1 analog/digital output stream (Left, Center, Right, LS, RS + LFE) FAROUDJA REALCOLOR Faroudja RealColor provides true 10-bit color processing Active color management with overlapping regions Adaptive Contrast Control Integrated noise filter to eliminate contrast noise FAROUDJA DCDI CINEMA FORMAT CONVERSION Low Angle De-interlacing processing Per Pixel Motion Adaptive De-interlacing (MADi) up to 1080i format Format conversion up to 1080p resolutions Adaptive 3D/TNR Noise Reduction Technical Information Summary 5
PICTURE-IN-PICTURE (PIP) Programmable PIP channel horizontal and vertical filter coefficients Flexible PIP, PBP, and POP support capability (Video, Graphics) DCDi Edge processing for second channel window FAROUDJA TRUELIFE VIDEO ENHANCER High performance programmable sharpening filters with Noise Coring Programmable Main channel horizontal and vertical filter coefficients Non-linear Chroma and Luma enhancement DDR2 MEMORY CONTROLLER 32-bitDDR2 memory I/F support ON-CHIP MICROPROCESSOR AND OSD CONTROLLER Integrated x186-based microprocessor General Purpose Inputs/Outputs (GPIOs) 2-wire serial master bus interface for external device control Integrated I/R decoder and low bandwidth ADC Advanced bit-mapped OSD controller OUTPUT FORMATS Dual-channel/single-channel 18/24/30-bit LVDS transmitters Single-channel 24/30-bit TTL output Adaptive Contrast Ratio (ACR) control for automatic, intelligent backlight adjustments Display Interface Features : Control signal generation for backlight inverter backlight dimming support (PWM and voltage controlled ) Voltage generation and power sequence control for panel Flat screens can be used with either 3.3V, 5V or 12V. JILI30/40/44 (LVDS) panel interface (one and double port up to 30 Bit) Operating Features: - 5 button user interface (OSD Keypad) - On Screen Display (OSD) control for all features - Full multi sync capable - VESA DPMS and DDC2B support - Single voltage supply (+12V/24V DC ) - Dynamic Power Management for minimal power consumption via DPMS - No software drivers needed! Technical Information Summary 6
4. Configuration 4.1 Backlight adjust JP600 Pin Description 1-2 PWM Adjust O 2-3 Linear Adjust O Never unplug / replug this while in use 4.2 Backlight-ON JP601 Pin Description 1-2 Active high BLON O 2-3 Active low BLON O Never unplug / replug this while in use Configuration 7
4.3 Backlight adjust level JP602 Pin Description 1-2 5V Adjust O 2-3 12V Adjust O Open 3.3V Adjust Never unplug / replug this while in use 4.4 Backlight voltage JP1500* Pin Description 1 O 2 1-2 5V 3 O O 4 3-4 12V 5 O O 6 Open 3.3V *Note: Not equipped on CRTtoLCD-71 (light). Backlight voltage is 12V (DC-IN) 4.5 Panel voltage JP1501 Pin Description 1 O 2 1-2 5V 3 O O 4 3-4 12V 5 O O 6 Open 3.3V Never unplug / replug this while in use 4.6 Display port power JP500 Pin Description 1-2 Board provides power to pin 20 of DP connector O Open Pin 20 DP connector open Never unplug / replug this while in use Configuration 8
5. Connectors 5.1 S-Video Input CN300* Pin Name Description 1 GND Power Ground O 2 GND Power Ground O 3 Y Y component of video signal O 4 C C component of video signal *Note: Not equipped on CRTtoLCD-71 (light) 5.2 Composite video input CN301* Pin Name Description 1 GND Power Ground O 2 CVBS CVBS video signal *Note: not equipped on CRTtoLCD-71 (light) Connectors 9
5.3 YUV analog input CN302 (optional) Description Name Pin Pin Name Description Red/Y in RED 1 O 2 GND Ground Green/U in GREEN 3 O O 4 GND Ground Blue/V BLUE 5 O O 6 GND Ground Audio Left 1 in AIL1 7 O O 8 GND Ground Audio Right 1 in AIR1 9 O O 10 GND Ground 5.4 VGA/RGB analog Input CN303 (optional) Pin Name Description 1 RED Analog input red O 2 GND Ground O 3 GREEN Analog input green O 4 GND Ground O 5 BLUE Analog input blue O 6 GND Ground O 7 DDC_SDA DDC Serial Data O 8 HSYNC Horizontal Sync input O 9 VSYNC Vertical Sync input O 10 DDC_SCL DDC Serial Clock O 11 GND Ground O 12 +5V in +5V Power Supply from Video Card 5.5 DVI-I input connector CN400 Description Name Pin Pin Name Description Receiver Signal(-) ( RX2- ) RX2-1 O 2 RX2+ Receiver Signal(+) ( RX2+ ) Power Ground GND 3 O O 4 NC Not connected Not connected NC 5 O O 6 SCL I 2 C clock I 2 C Data SDA 7 O O 8 VS Analog vertical sync Receiver Signal(-) ( RX1- ) RX1-9 O O 10 RX1+ Receiver Signal(+) ( RX1+ ) Power Ground GND 11 O O 12 NC Not connected Not connected NC 13 O O 14 +5V +5V from DVI video card Power Ground GND 15 O O 16 HP Hot Plug Receiver Signal(-) ( RX0- ) RX0-17 O O 18 RX0+ Receiver Signal(+) ( RX0+ ) Power Ground GND 19 O O 20 NC Not connected Not connected NC 21 O O 22 GND Power Ground Clock Signal(+) (RXC+) RXC+ 23 O O 24 RXC- Clock Signal(-) (RXC-) Analog red RED C1 O O C2 GREEN Analog green Analog blue BLUE C3 O O C4 HS Analog horizontal sync Analog GND GND C5 O O C5-1 GND Analog GND Connectors 10
5.6 Display Port connector CN500 Pin Name Description 1 ML_Lane 0 (p) Lane 0 (positive) O 2 GND Ground O 3 ML_Lane 0 (n) Lane 0 (negative) O 4 ML_Lane 1 (p) LANE 1 (POSITIVE) O 5 GND Ground O 6 ML_Lane 1 (n) Lane 1 (negative) O 7 ML_Lane 2 (p) Lane 2 (positive) O 8 GND Ground O 9 ML_LANE 2 (N) LANE 2 (NEGATIVE) O 10 ML_Lane 3 (p) Lane 3 (positive) O 11 GND GROUND O 12 ML_Lane 3 (n) LANE 3 (NEGATIVE) O 13 GND Pulled to Ground O 14 GND Pulled to Ground O 15 AUX CH (p) Auxiliary Channel (positive) O 16 GND Ground O 17 AUX CH (n) Auxiliary Channel (negative) O 18 Hot Plug Hot Plug Detect O 19 RETURN Return for Power O 20 DP_PWR POWER FOR CONNECTOR (3.3 V 500 MA) Connectors 11
5.7 JILI44-Interface CN600* Description Name Pin Pin Name Description Enables Backlight BLON# 1 O 2 BLADJ Backlight Adjust Even Rx Signal(-) (R2IN 4+) STX4+ 3 O O 4 STX4- Even Rx Signal(-) (R2IN 4-) Power Ground GND 5 O O 6 STX3+ Even Rx Signal(-) (R2IN 3+) Even Rx Signal(-) (R2IN 3-) STX3-7 O O 8 GND Power Ground Even Clock Signal(+) (CK2IN +) STXC+ 9 O O 10 STXC- Even Clock Signal(-) (CK2IN -) Power Ground GND 11 O O 12 STX2+ Even Rx Signal(+) (R2IN 2+) Even Rx Signal(-) (R2IN 2-) STX2-13 O O 14 GND Power Ground Even Rx Signal(+) (R2IN 1+) STX1+ 15 O O 16 STX1- Even Rx Signal(-)(R2IN 1-) Power Ground GND 17 O O 18 STX0+ Even Rx Signal(+) (R2IN 0+) Even Rx Signal(-) (R2IN 0-) STX0-19 O O 20 GND Power Ground Odd Rx Signal(+)(R1IN 4+) FTX4+ 21 O O 22 FTX4- Odd Rx Signal(+)(R1IN 4-) Power Ground GND 23 O O 24 FTX3+ Odd Rx Signal(+)(R1IN 3+) Odd Rx Signal(-) (R1IN 3-) FTX3-25 O O 26 GND Power Ground Odd Clock Signal(+) (CK1IN +) FTXC+ 27 O O 28 FTXC- Odd Clock Signal(-) (CK1IN -) Power Ground GND 29 O O 30 FTX2+ Odd Rx Signal(-) (R1IN 2+) Odd Rx Signal(+)(R1IN 2+) FTX2-31 O O 32 GND Power Ground Odd Rx Signal(+) (R1IN 1+) FTX1+ 33 O O 34 FTX1- Odd Rx Signal(-) (R1IN 1-) Power Ground GND 35 O O 36 FTX0+ Odd Rx Signal(+)(R1IN 0+) Odd Rx Signal(-) (R1IN 0-) FTX0-37 O O 38 GND Power Ground I 2 C clock SCL 39 O O 40 SDA I 2 C Data Panel VCC ( switched ) Vcc_P 41 O O 42 Vcc_P Panel VCC ( switched ) Panel VCC ( switched ) Vcc_P 43 O O 44 Vcc_P Panel VCC ( switched ) *Note: Not equipped on CRTtoLCD-71 (light) 5.8 JILI40-Interface CN601 Description Name Pin Pin Name Description Enables Backlight BLON# 1 O 2 BLON# Enables Backlight Backlight Adjust BLADJ 3 O O 4 STX3+ Even Rx Signal(+) (R2IN 3+) Even Rx Signal(-) (R2IN 3-) STX3-5 O O 6 VIN DC Input from CN1500/CN1501 Even Clock Signal(+) (CK2IN +) STXC+ 7 O O 8 STXC- Even Clock Signal(-) (CK2IN -) DC Input from CN1500/CN1501 VIN 9 O O 10 STX2+ Even Rx Signal(+) (R2IN 2+) Even Rx Signal(-) (R2IN 2-) STX2-11 O O 12 VIN DC Input from CN1500/CN1501 Even Rx Signal(+)(R2IN1+) STX1+ 13 O O 14 STX1- Even Rx Signal(-) (R2IN 1-) DC Input from CN1500/CN1501 VIN 15 O O 16 STX0+ Even Rx Signal(+) (R2IN 0+) Even Rx Signal(-) (R2IN 0-) STX0-17 O O 18 VIN DC Input from CN1500/CN1501 Odd Rx Signal(+)(R1IN 3+) FTX3+ 19 O O 20 FTX3- Odd Rx Signal(-) (R1IN 3-) Power Ground GND 21 O O 22 GND Power Ground I 2 C clock SCL 23 O O 24 SDA I 2 C Data Power Ground GND 25 O O 26 FTXC+ Odd Clock Signal(+) (CK1IN +) Odd Clock Signal(-) (CK1IN -) FTXC- 27 O O 28 GND Power Ground Odd Rx Signal(+)(R1IN 2+) FTX2+ 29 O O 30 FTX2- Odd Rx Signal(-) (R1IN 2-) Power Ground GND 31 O O 32 FTX1+ Odd Rx Signal(+) (R1IN 1+) Odd Rx Signal(-) (R1IN 1-) FTX1-33 O O 34 GND Power Ground Odd Rx Signal(+)(R1IN 0+) FTX0+ 35 O O 36 FTX0- Odd Rx Signal(-) (R1IN 0-) Power Ground GND 37 O O 38 GND Power Ground Panel VCC ( switched ) Vcc_P 39 O O 40 Vcc_P Panel VCC ( switched ) Connectors 12
5.9 JILI30-Interface CN603 Description Name Pin Pin Name Description Odd Rx Signal- (R1IN 0-) FTX0-1 O 2 FTX0+ Odd Rx Signal+ (R1IN 0+) Odd Rx Signal- (R1IN 1-) FTX1-3 O O 4 FTX1+ Odd Rx Signal+ (R1IN 1+) Odd Rx Signal- (R1IN 2-) FTX2-5 O O 6 FTX2+ Odd Rx Signal+ (R1IN 2+) Power Ground GND 7 O O 8 FTXC- Odd Clock Signal- (CK1IN -) Odd Clock Signal+ (CK1IN +) FTXC+ 9 O O 10 FTX3- Odd Rx Signal- (R1IN 3-) Odd Rx Signal+ (R1IN 3+) FTX3+ 11 O O 12 STX0- Even Rx Signal- (R2IN 0-) Even Rx Signal+ (R2IN 0+) STX0+ 13 O O 14 GND Power Ground Even Rx Signal- (R2IN 1-) STX1-15 O O 16 STX1+ Even Rx Signal+ (R2IN 1+) Power Ground GND 17 O O 18 STX2- Even Rx Signal- (R2IN 2-) Even Rx Signal+ (R2IN 2+) STX2+ 19 O O 20 STXC- Even Clock Signal- (CK2IN -) Even Clock Signal+ (CK2IN +) STXC+ 21 O O 22 STX3- Even Rx Signal- (R2IN 3-) Even Rx Signal+ (R2IN 3+) STX3+ 23 O O 24 GND Power Ground I²C Data SDA 25 O O 26 DEN Display Enable I²C Clock SCL 27 O O 28 Vcc_P Panel VCC ( switched ) Panel VCC ( switched ) Vcc_P 29 O O 30 Vcc_P Panel VCC ( switched ) 5.10 Backlight Connector CN602 Pin Name Description 1 BLON BACKLIGHT CONTROL SIGNAL O 2 GND Power Ground O 3 GND Power Ground O 4 Backlight power supply TYPICAL. +12V (NOTE SAME AS DC INPUT O 5 Backlight power supply O 6 Backlight power supply O 7 Backlight power supply VOLTAGE, 1 AMPERE PER CONTACT ALLOWED) O 8 GND Power Ground O 9 GND Power Ground O 10 BKLTADJ analog 0V to +5V or 0V to +12V 5.11 Audio input/output CN700* Description Name Pin Pin Name Description Line out left AOL 1 O 2 GND Ground Line out right AOR 3 O O 4 GND Ground Line in left 2 AIL2 5 O O 6 GND Ground Line in right 2 AIR2 7 O O 8 GND Ground SPDIF in SPDIFI 9 O O 10 GND Ground SPDIF out SPDIFO 11 O O 12 +3.3V +3.3V power supply *Note: Not equipped on CRTtoLCD-71 (light) Connectors 13
5.12 IR input CN800 Pin Name Description CN1001 1 VCC 3.3 Volts output O 2 GND Power Ground O 3 Out Output from the IR receiver 5.13 OSD keypad connector CN802 Description Name Pin Pin Name Description +5V DC Power VCC 1 O 2 LED LED ENA (OC / BKL_VCC) Confirm Key (TTL) KEY 3 O O 4 KEY OSD Menu key (TTL) Down Key (TTL) KEY 5 O O 6 KEY Up Key (TTL) ADC Input *Note1 ADC1 7 O O 8 IR Output of IR receiver Switch LED (TTL) KEY 9 O O 10 KEY ON/OFF Key (TTL) Low active Reset (TTL) /Reset 11 O O 12 +12V +12V DC Power Power Ground GND 13 O O 14 GND GND *Note1: Input range is 0-3V. Shared with CN900 5.14 ADC Input Connector CN900 (Light Sensor Input) Connector: Molex 53261-0590 Matching Connector: Molex 51021-0500 Pin Name Description 1 GND Power Ground O 2 ADC1 ADC1 Input *Note1 O 3 DVDD3.3 3.3 VOLT OUTPUT SOURCE (MAX.50MA) O 4 ADC2 ADC2 Input *Note1 O 5 GND Power Ground *Note1: Input range is 0-3V. Onboard pulled up to DVDD3.3 through 4, 7 KΩ resistor. 5.15 GPIO Connector CN901 Connector: Molex 53261-0590 Matching Connector: Molex 51021-0500 Pin Name Description 1 DVD3.3 3.3 Volt output source (max.50ma) O 2 GND Ground O 3 GPIO0 General Purpose I/O / PWM0 O 4 GPIO1 General Purpose I/O / PWM1 O 5 GPIO2 General Purpose I/O / PWM2 Connectors 14
5.16 RS232 Serial OSD connector CN1300 Description Name Pin Pin Name Description Not Connected NC 1 O 2 NC Not Connected Transmit Signal 1 TXD1 3 O O 4 RXD2 Receive Signal 2 Receive Signal 1 RXD1 5 O O 6 TXD2 Transmit Signal 2 Not Connected NC 7 O O 8 NC Not Connected Power Ground GND 9 O O 10 +5V +5V DC Power 5.17 DC Power Supply 4-Pol. CN1500 Pin Name Description 1 NC Not connected O 2 GND Power Groundl O 3 GND Power Ground O 4 +12V 12V DC Power 5.18 DC Power Supply DC-Jack CN1501 Pin Name Description O 1 +12V +12 V DC O 2 GND Power Ground Connectors 15
6. On Screen Display With the OSD ( On Screen Display ) you can modify the settings and control the special features of the CRTtoLCD-71. The OSD uses a number of menus for making changes and turning the special features on or off. The configuration can be done via the OSD-keypad (OSD-Panel-Kit). To start the OSD press the OSD button on the keypad, after switching the power supply on. If a valid flat panel configuration is installed, the OSD Main Menu will be displayed. To select an menu point, simply use the button UP or DOWN to move the cursor to the menu point you want and press the button OSD. To get back to the previous menu point press the CONFIRM button. To select a function, simply use OSD -button to select the field. Use UP or DOWN to select a value for that field. With the CONFIRM button you can exit the current function. On Screen Display 16
6.1 OSD Description Main Menu DisplayPort Main Picture Channel DVI VGA SVideo Video Set main input to selected input Scan Input On Off Enable scanning of Main and PiP inputs Disable scanning of inputs PiP Mode Off Small Large Disable PiP Shown PiP in small window Show PiP in large window Input Select Side by Side DisplayPort Show PiP Side by Side PiP Channel DVI VGA SVideo Video Set PiP channel to selected input PiP Position Bottom / Right Top / Right Bottom / Left Top / Left Set PiP to lower-right corner Set PiP to upper-right corner Set PiP to lower-left corner Set PiP to upper-left corner Swap Main & PiP Swap main an PiP channel On Screen Display 17
Main Menu 12 = Disabled Sharpness 0 24 11-0 = smoothing filter 13 24 = sharpness filter (only working on analogue inputs) Image Adjustments Off 1.8 Disable Gamma correction Gamma 2.0 2.2 2.4 Modify output Gamma by selected correction table 2.6 Image Adjustments Off Adaptive Disable dynamic noise reduction Set noise filter strength dynamically depending on measured noise data Dynamic NR Mode Low Medium High Set static noise reduction filter Max MPEG NR Mode On Off Enable/Disable MPEG noise reduction to compensate MPEG/JPEG artefacts Advanced DCDi On Off Enable/Disable Directional Correlation DeInterlacing that eliminates jagged edges doing lowangle diagonal interpolation Off Disable motion processing for interlaced inputs Motion Processing Adaptive Combine normal de-interlacing with motion detection Normal Odd and even filed will be outputted together Off Disable film mode detection Film Mode Video 2:2 Video 3:2 Video 3:2+2:2 Enable film mode detection using selected method Decoder Settings Y-Bias Y-Gain Luminance bias for video decoder Luminance gain of video decoder C-Gain Color gain of video decoder On Screen Display 18
Main Menu Auto Adjust Setup and settle input image automatically On success, mode data will be save for this mode Clock Range dep. on input Adjust horizontal total Image Adjustments Phase 0-63 Adjust H-Phase Hor. Position Range dep. on input Shift image depending on H- Porches Ver. Position Range dep. on input Shift image depending on V- Porches On Screen Display 19
Main Menu Scheme Off Vivid Cinema Gaming Scheme is disabled Vivid color scheme Cinema color scheme Gaming color scheme Backlight 0-100 Adjust intensity of backlight Brightness 0-100 Adjust digital brightness Contrast 0-100 Adjust digital contrast User Disable color temp. and activate user RGB adjustments 4200K Color Adjustment Color Temp. 5000K 6500K Set color temperature to desired value in Kelvin 7200K 9300K RGB Red Green Blue Adjust user color Range 0-100 Saturation 0-100 Adjust Saturation (only possible on Video / SVideo) Hue 0-100 Adjust Hue (only possible on Video / SVideo) Auto Color Adjust Calibrate internal ADC s On Screen Display 20
Main Menu Full Screen Zoom/shrink input to fully fit into display Main Scaling Mode Letter Box Pillar Box Letter Box Expand Pillar Box Expand Select different Letter Box and Pillar Box scaling modes Scaling Adjustments Native 1:1 scaling Zoom Hor. Horizontal zoom in % Ver. Vertical zoom in % Zoom Pos. Hor. Ver. Select horizontal and vertical position of zoom window in % Main Menu Volume 0-100 Master volume Balance -10 to +10 Balance between left and right audio channel Audio Settings Bass -10 to +10 Increase / decrease bass Treble -10 to +10 Increase / decrease treble Auto Volume On Off Enable / Disable auto volume This keeps volume on master volume level On Screen Display 21
Main Menu OSD Timeout 0-60 OSD Timeout in seconds, 0 = Disable timeout OSD Hor. Pos. 0-100 Horizontal OSD position in % OSD Ver. Pos. 0-100 Vertical OSD position in % OSD Blend 0-10 OSD transparency 0 = No transparency 10 = maximum level of transparency OSD Settings 0 OSD Orientation 90 180 270 Rotation of OSD OSD Language English German French Italian Spanish OSD Language On Screen Display 22
Main Menu Info System Settings Mode Info Restore user defaults Restore further saved user defaults Save user defaults Save use defaults Reset factory default Reset factory defaults This will load firmware defaults but not erases the previous saved user defaults On Screen Display 23
7. Technical Specifications These values were measured with OSD-Panel attached and without flatpanel and backlight inverter. 7.1 Supply Voltage and Current - Supply voltage at 25 C : Minimum supply voltage Typical supply voltage Absolute Maximum supply voltage + 11,4 V DC / 22,8 V DC + 12,0 V DC / 24V DC + 12.6 V DC / 25.2 V DC - Typical Input current at 25 C: (OSD-Keypad connected, SXGA@60Hz via DisplayPort, no display attached) CRTtoLCD-71 (normal operating): CRTtoLCD-71 (Soft-Power-Down / Standby): 386 ma @ 12V 105 ma @ 12V - Supply voltage ripple: 100 mv peak to peak 0 20 MHz VGA connector signals : Sync input voltage low : Sync input voltage high: RGB input voltage: termination RGB input current: 0.8 V 2.4 V 0 0.7 V with 75 Ohm external 0 5 ma - Current Rating of Flatpanel Power supply (preliminary): PANEL VCC Steady State 3V / 5V and 12V @ +-5% : 3A PANEL VCC 5sec. -5% 3V3 @5,6A PANEL VCC 5sec. -5% 5V @ 5,15A PANEL VCC 5sec. -2% 12V @ 4A Note: Output power without any switch or short circuit breaker Technical Specifications 24
7.2 Temperature - Temperature: ambient: 0 C 60 C (*1) non operating: -10 C 85 C (*1) The maximum operating temperature is the maximum measurable temperature on any spot on the module surface. It is the user responsibility to keep this temperature within the above specification. - Temperature gradient: operating: non operating: - Relative Humidity: operating: non operating: 25 C per hour 40 C per hour 10% - 90% RH non-condensing 5% - 95% RH non-condensing - Mechanical: Shock: Vibration: 5G/20ms square wave maximum 1G/0-600Hz, dwell not to exceed 7.3 Mechanical Diamensions - Dimensions of the printed circuit board: Width: Length: Thickness: - Dimensions of the module: Width: Length: Height: 114.29 mm 179.07 mm 1.50 mm 119.50 mm 179.07 mm 16.50 mm max. 35mm Note : The dimension of the module may vary depending on P/N or change if cable, Adapter or Keypad plugged in! Technical Specifications 25
8. Supported Video Modes Generally all VESA compatible video modes are supported. If modes are not supported the controller displays Invalid Mode on the flat panel. In this case use the Configuration Workbench (KCWB), available on request, to add this special mode to the supported mode table. Following modes are tested: Video Mode Input Vertical refresh rate Mode standard 720 x 400 70 Hz DOS 640 x 350 70 Hz DOS 640 x 400 70 Hz DOS 640 x 480 59,9 Hz VGA 640 x 480 60 Hz VGA 640 x 480 72 Hz VGA 640 x 480 72,8 Hz VGA 640 x 480 75 Hz VGA 640 x 480 85 Hz VGA 800 x 600 56,25 Hz SVGA 800 x 600 60 Hz SVGA 800 x 600 70 Hz SVGA 800 x 600 72 Hz SVGA 800 x 600 75 Hz SVGA 800 x 600 85 Hz SVGA 1024 x 768 60 Hz XGA 1024 x 768 70 Hz XGA 1024 x 768 72 Hz XGA 1024 x 768 75 Hz XGA 1024 x 768 85 Hz XGA 1152 x 864 75 Hz XGA+ 1280 x 1024 60 Hz SXGA 1280 x 1024 70 Hz SXGA 1280 x 1024 75 Hz SXGA 1280 x 1024 85 Hz SXGA 1600 x 1200 60 Hz UXGA 1920 x 1200 60 Hz WUXGA Supported Video Modes 26
9. Layout / Schematics 9.1 Board Layout / Schematics 27
9.2 OSD Panel OSD-KEYPAD OSD-PANEL Power ON/OFF LED 120 MM 25 mm Keypad JP1 connected to CN2 of CRTtoLCD-71 Layout / Schematics 28
10. Technical Support Please report any errors or problems to this email address: aflat@ecount-consulting.com. Normally, there is no telephone support. In your email message, please include the following information: - Company Name - Your Name - Address - Email - Telephone/Fax - Description of the hardware, etc. - Description of the used software. - Description of the error. Technical Support 29
11. Revision History Date Author Version Description 01.07.2014 A.Stauffenberg 1.0 Initial Release Corrected JILI44 and JILI40 pin description Removed USB option Removed TTL serial port option 05.02.2015 V. Irion 1.1 Corrected board dimensions Updated typical input current Corrected name of backlight connector 04.03.2015 V. Irion 1.2 Added Note for CRTtoLCD-71 (light) Added Pin numbers for JP1500 / JP1501 06.05.2015 V. Irion 1.3 Changed name of GPIO connector to CN901 22.07.2015 V. Irion 1.4 03.05.2015 V. Irion 1.5 Corrected CN801 Added description of OSD Changed name of OSD connector to CN802 Corrected voltage on CN800 Corrected CN400 description Revision History 30