Two separate x5 video and stereo audio sections Possibility of x5 dual or x0 single configuration Suitable for composite or Y/C signals Suitable for unbalanced stereo audio or mono balanced signals Ed. /2/2008 Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375
INSTALLATION AND USE OF THE SUMMARY.0 Overview 3 2.0 Power supply 4 3.0 Installation 5 4.0 Technical data 9 5.0 Notes 0 When installing the unit, please read this handbook carefully. The manufacturer shall not be held responsible for damage due to use, even correct, of its products. The data and characteristics of the product may be modified without prior notice. All updates and news regarding this products are published on our site www.elprovideolabs.com Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375 2
.0 OVERVIEW Thank you for purchasing this product. Check the contents of the packaging carefully. It contains: The unit This handbook and the certificate of conformity The power cord The is a dual x5 video and stereo audio distributor that can, if necessary, be configured as a single x0 distributor. 3 Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375
2.0 POWER SUPPLY The must be powered at 90 240 Vac 50/60Hz using the cable provided. The socket of the cable must be inserted in the related panel plug to the left on the back of the unit. The panel plug is equipped with a fuse holder for 5X20 fuses. If the fuse blows, replace it with one of the same rating that s AT. All operations must be carried out by qualified personnel only, who must be informed of the risks of electric shock. In some countries, the plug of the cable must be adapted to local standard types. The wires are coded as follows: Brown PHASE Identified by the letter L, may be red Blue NEUTRAL Identified by the letter N, may be black Yellow/green GROUND Identified by the letter E, may be green WARNING A ground connection is compulsory Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375 4
3.0 INSTALLATION 3. Video section 3.. Dual x5 distributor To use the unit as dual x5 distributor with two sources, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the DUAL x5 position remembering that this setting acts not only on the video but also on the audio. c) Connect the first video source to one of the two IN connectors and the second source to one of the two IN2 connectors. d) If the input signal is not terminated at 75Ω, set the matching switch to the ON position. If the signal is already terminated at 75Ω, set the switch to OFF. The switch of input IN is located to the left of the respective BNCs, that of input IN2 is located to the right. e) The input BNC not used can be left free or can be used, if necessary, to send the video signal to other units. In this case, remember that termination at 75Ω must be carried out at only one point of the chain, preferably at the end of this. Therefore, in this case, the 75 Ohm switch must be set to a OFF. f) Connect the destinations to BNCs 5 VIDEO OUT on both sections. The BNCs at the top refer to section, those at the bottom refer to section 2. g) Power the and other system units. 5 Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375
3..2 Single x0 distributor To use the unit as x0 single distributor, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the x0 position remembering that this setting acts not only on the video but also on the audio. c) Connect the video source to one of the two IN connectors d) If the input signal is not terminated at 75Ω, set the switch referring to the IN input (located to the left of the related BNCs) to the ON position. If the signal is already terminated at 75Ω, set the switch to OFF. The position of the switch relating to IN2 is not significant in this operating mode. e) The BNC not used, relating to input IN, can be left free or can be used, if necessary, to send the video signal to other units. In this case, remember that termination at 75Ω must be carried out at only one point of the chain, preferably at the end of this. Therefore, in this case, the 75 Ohm switch must be set to a OFF. f) As the two IN2 connectors are not used in this operating mode, connection of these is not significant. g) Connect the destinations to the VIDEO OUT BNCs. h) Power the and other system units. Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375 6
3.2 Audio section 3.2. Dual x5 distributor To use the unit as dual x5 distributor with two sources, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the DUAL x5 position remembering that this setting acts not only on the video but also on the audio. c) Connect the first audio source to the AUDIO IN connectors and the second source to the AUDIO IN2 connectors. If the source is mono, only one of the two channels (L or R) can be used. d) Connect the destinations to the AUDIO OUT and AUDIO OUT2 connectors respectively. e) Power the and other system units. 3.2.2 Single x0 distributor 7 Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375
To use the unit as single x0 distributor, proceed as follows: a) Make sure that all the units to be installed are OFF. b) Set the switch on the front panel to the x0 position remembering that this setting acts not only on the video but also on the audio. c) Connect the audio source to the AUDIO IN connectors. If the source is mono, only one of the two channels (L or R) can be used. As the AUDIO IN2 connectors are not active in this configuration, their connection is not significant. d) Connect the destinations to the AUDIO OUT and AUDIO OUT2 connectors. e) Power the and other system units. Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375 8
4.0 TECHNICAL DATA 4. Video Input type AC coupled Input ret.loss 32 db @ 5 MHz worst case Input level Max 2 Vpp on 75Ω Output gain 0 db Output ret.loss 44 db @ 5 MHz worst case Frequency response 0.0 db @ 9 MHz 0.5 db @ 0 MHz ±3 db @ 20 MHz Delay 8 ns Differential gain 0.3% Differential phase 0.2 Hum & noise -84 db unweighted Crosstalk 45dB (two sections) @5MHz, worst case Hum & noise -84 db unweighted 4.2 Audio Input Input impedance Input level CMRR Output impedance Output gain AC coupled 56KΩ +0dBm Max 36dB at 5KHz 50Ω 0 db Frequency response ±0.0 db from 7 Hz to 330 KHz ± 3 db up to 6MHz Harmonic distorsion Hum & noise Crosstalk <0.05%@ 0dBm -74 db unweighted 54 db (two sections) at 6KHz worst case 5 db (left/right) at 6KHz worst case 9 Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375
4.3 General characteristics Main input 230Vac Power consumption 5VA Size (WXDXH) 483x49x44mm Weight 2.0Kg Operating temp. Range 0 45 C Safety according to EN 60065 EMC according to EN 5503- and EN 5503-2 Mark 5.0 NOTES This product is warranted for 5 years from the date of purchase. If the fault in the product is due to improper use or operations carried out by third parties, the warranty is forfeited. During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note. The units repaired will be returned CARRIAGE FORWARD to the addressee. Outside the warranty period, Elpro will repair the faulty units EX its Turin offices, charging the cost of the repair to the customer. For any problems during installation of the, call the Elpro hot-line Tel. +39 0 770583 or e-mail: info@elprovideolabs.com Str.da della Pronda, 45/B 042 TORINO - ITALY Tel.+39 0770583 Fax +39 070375 0