USER MANUAL HN-IA60E200FS 1080P AHD/CVI/TVI/1200TVL Varifocal Outdoor Camera
Product Description The HN-IA60E200FS is a high-definition camera designed around a 1/2.9" Sony IMX323 2.19MP image sensor, 42µ x 4pcs IR LEDs providing infrared capability up to 130 feet, and a 2.8-12mm manual zoom lens for 26-90 degrees horizontal angle of view. The ability to send HD video over coaxial cable makes the HN-IA60E200FS a cost effective high-definition surveillance solution for any budget. Please read this user manual carefully to ensure proper use of the product. Device Connection Note: Before connecting the power supply, please check its output voltage, 12V 2A recommended.
Notice Before Using Default Mode: 1080P AHD Video Output. If your DVR is TVI, CVI or Analog DVR, please take the OSD cap off and switch the OSD joystick to the corresponding video output mode. OSD POWER ON the camera, switch the OSD joystick: LEFT Push 5s to 1200TVL mode for analog DVR. RIGHT Push 5s to TVI mode for 1080P TVI DVR or XVR. DOWN Push 5s to CVI mode for 1080P CVR or XVR. UP Push 5s to AHD mode for 1080P (N) AHD DVR or XVR. Note: 5s means 5 seconds Installation and Operation: 1. Unpacking and Handling Each unit is shipped assembled and factory tested. Ensure that all accessories are removed from the container before discarding packing material. Package includes 1x bullet camera 4x screw anchors 1x user manual 1x Allen wrench 4x mounting screws 1x install guide 1x drill template 1x screw driver (adjust bracket)
2. Mechanical Inspection Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged or defective please contact us for assistance. 3. Special Attention (i) The installer must comply with electrical safety standards. There must be sufficient space between the camera's power supply and video line and any high voltage equipment and/or cables. (ii) To help ensure the camera's life and proper operation do not point the camera towards the sun or strong light. (iii) Do not install the camera in an environment where the temperature is too high or too low, recommended operating temperature is 14F ~ 122F. (iv) Do not install the camera near a magnetic field or a high-power motor. (v) Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove, wipe gently with a mild detergent. Never use strong or abrasive detergents. (vi) A 12V DC 1A or 2A power supply must be used. AC power cannot be applied. AC power will damage the camera and void warranty. Power supply output voltage, current, voltage polarity and operating temperature must match requirement of this equipment.
(vii) Only qualified installers are allowed to install, test and disassemble the camera. (viii) The camera is a low voltage product. If installed outdoors, proper safety and lightening grounding are required. 4. Wiring Connections (i) Connect the power supply's DC plug to the camera's power outlet. (ii) Connect the camera to the DVR with a 75Ω coaxial video cable. (iii) Connect power supply's AC plug to a suitable AC power outlet. (iv) Adjust the lens direction according to the required surveillance area and environment. 5. Adjusting Zoom and Focus This cameras will come from the factory set for the wide field of view, meaning that it has the low magnification. Turn the Zoom screw (near the lens) anticlockwise to increase the magnification and then adjust the Focus until the image is clear.
Note: It can be difficult to know what the right zoom and focus settings are and these adjustments are best made when the camera is at its intended location. There are several methods one can use to ensure proper adjustments: 1. A second person located at the DVR, monitoring the picture from the camera and communicating with the person making the adjustments. 2. Using a smartphone running the appropriate mobile monitoring app to view the camera. 3. Use of an LCD camera tester which temporarily connects to the video. 6. Camera Lens Angle 1/3"CMOS Lens(mm) Left/Right 1/3"CMOS Up/Down 2.8mm 89.9 79.8 3.6mm 75.7 66 4mm 69.9 60.7 6mm 50 42.6 8mm 38.5 32.6 12mm 26.2 22.1
7. Detailed Lens Chart Detailed Lens Chart 5 feet 10 feet 25 feet 2.8mm 6.4 * 8.6 12.9 * 17.1 32.1 * 42.9 4.0mm 4.5 * 6.0 9.0 * 12.0 22.5 * 30.0 6.0mm 3.0 * 4.0 6.0 * 8.0 15.0 * 20.0 8.0mm 2.3 * 3.0 4.5 * 6.0 11.3 * 15.0 12.0mm 1.5 * 2.0 3.0 * 4.0 7.5 * 10.0 50 feet 75 feet 100 feet 2.8mm 63.4 * 85.7 96.4 * 128 128.6 * 171.4 4.0mm 45.0 * 60.0 67.5 * 90.0 90.0 * 120.0 6.0mm 30.0 * 40.0 45.0 * 60.0 60.0 * 80.0 8.0mm 22.5 * 30.0 33.8 * 45.0 45.0 * 60.0 12.0mm 15.0 * 20.0 22.5 * 30.0 30.0 * 40.0 Setup OSD Menu Press the OSD joystick to start the OSD menu in any video output mode, OSD menu will show on display as following: MAIN MENU AE AWB DAY NIGHT IMAGE ENHANCE VIDEO SETTING LANGUAGE RESET SAVE-EXIT EXIT
OSD Functions and Options MAIN MENU BRIGHTNESS GLOBE EXPOSURE AE MODE BLC ADVAN SHUTTE AUTO/M GAIN AUTO/M -CED RETURN RETURN ATW AWB MODE MWB RGAIN BGAIN RETURN DAY- NIGHT MODE SMART COLOR B/W RETURN CONTRAST AUTO/MANUAL IMAGE ENHANCE VIDEO SETTING LANGUAG RESET SAVE-EXIT EXIT SHARPNES AUTO/MANUAL COLOR AUTO/MANUAL 3DNR AUTO/MANUAL RETURN FORMAT NTSC/PAL MODE AHD/CVI/CVBS/TVI D-WDR OPEN/CLOSED RETURN ENGLISH, CHINESE, TRADITIONAL CHINESE
BLC (Back Light Compensation): In images where a bright light source is behind the subject of interest, the subject would normally appear in silhouette. BLC allows the camera to adjust the exposure of the entire image to properly expose the subject in the foreground. SHUTTER Control (Shutter Speed): Could be adjusted in manual mode from 1/30-1/10000 based on lighting condition. Gain Control: Could be adjusted in manual mode, Analog gain control from 1-16 and digital gain control from 1-15. ATW (Auto Tracking White Balance): White Balance allows the camera to adjust the tone according to the color temperature of the light source illuminating the subject. It allows the operator to see objects as they appear during daylight. MWB (Manual White Balance): Adjust the red gain and blue gain manually to produce white accurately picture. Day Night Mode: a. Smart: Provide color image at daytime and black and white image at nighttime automatically by smart light sensor and IR-cut. b. Color: Provide color image both at daytime and nighttime. c. B/W: Provide black and white image both at daytime and nighttime. Contrast: Contrast is defined as the separation between the darkest and brightest areas of the image. Increase contrast and you increase the separation
between dark and bright, making shadows darker and highlights brighter. Decrease contrast and you bring the shadows up and the highlights down to make them closer to one another. Sharpness: Sharpness can be defined as edge contrast, that is, the contrast along edges in a photo. When we increase sharpness, we increase the contrast only along/near edges in the photo while leaving smooth areas of the image alone. Color Gain: Color gain means saturation, it is similar to contrast, however instead of increasing the separation between shadows and highlights, it increases the separation between colors. 3DNR (Digital Noise Reduction): DNR is a technique of removing image noise from a video signal by applying a digital comb filter. It reduces the noise that can be found in low light images and makes images clearer. This type of filter is sometimes confused by motion, resulting in blur trails. Video Format: PAL and NTSC, its NTSC in USA. D-WDR: Digital WDR (D-WDR) is a software-based technique that optimizes image quality by adjusting the gamma (γ) value to enhance dark areas. Reset: If you need factory reset all the OSD menu settings, choose reset option. Save Exit: Make sure click SAVE EXIT for any setting change if you need to keep the setting. Exit: Leave the OSD menu.
Specifications Model No. Video Output Mode HN-IA60E200FS AHD/CVI/TVI/CVBS Camera Image Sensor Image Resolution Effective Pixels TV System Electronic Shutter S/N Ratio Scanning System 1/2.9" Sony CMOS Image Sensor 1080P / 1200TVL 1920*1080 in HD mode PAL/NTSC 1/30s~1/10,000s 50dB Progressive Scan Lens Focus Length Horizontal View Angle Lens Type Pixels 2.8-12mm 26-90 Degrees Manual Zoom 2 Mega Pixels Night Vision Infrared LED Infrared Distance IR Status IR Power On 42µ x 4pcs 100-130 Feet* Under 10 Lux by CDS CDS Auto Control Camera Features Day/Night OSD Menu Language White Balance Gain Control Noise Reduction Picture Adjustment YES YES AUTO / MANUAL AUTO / MANUAL 3DNR YES
DWDR OSD Support UTC YES YES YES (HD Mode Only) General Housing Bracket IR Cut Filter Operation Temperature Storage Temperature Power Source Dimension Weight Metal, IP66 YES YES 14F ~ 122F RH95% Max -4F ~ 140F RH95% Max DC12V±10%, 1000mA 200(W) x 171(H) x 83(D)mm 1400g *Stated maximum IR range is based on ideal conditions in typical outdoor environment. Actual range and image clarity depends on installation location, viewing area and light reflection / absorption level of object. Trouble Shooting a. No picture or only black and white picture after applying power (i) Check all plugs and cables are securely connected to the proper connectors. (ii) Ensure your power supply is providing the correct voltage and current. (iii) Ensure switch the camera video output mode to correspond your DVR video type. (iv) Ensure your AHD DVR is 1080P or 1080N, CVI and TVI DVR is 1080P. b. The picture has ripples
(i) Check to see if the power supply is experiencing AC ripple, if so a filter may be required. (ii) Determine if the monitor is faulty. (iii) Determine if other peripheral equipment is causing ripple and if so make the necessary adjustments. c. The picture appears smeared (i) The power supply voltage level may be unstable, therefore, try another power supply. (ii) Ensure the cables are correctly connected and/or the cables are of the correct impedance. d. The picture background continuously changes color (i) A fluorescent lamp's magnetic field may cause color roll, therefore, reduce the number of fluorescent lamps or increase the distance between the camera and the lamps. Camera Dimensions (mm)
Frequently Asked Questions Q: Does this camera work with 720P DVR system? A: No, the video signal is 2MP 1080P, it could not work with 720P DVR. Q: How should I switch the video mode? A: Please check notice before using above. Q: Will the OSD switch stay in same mode if camera is powered off, or do you have to reset mode each time you power it back up? A: It will stay in the same output mode, do not need to reset each time. A: Why the color is black and white at daytime? A: Make sure the camera video signal match your DVR. First check the DVR signal type, then adjust the OSD joystick to corresponding signal mode to make it match. Make sure the camera and DVR are with same video format, both NTSC or both PAL. Q: Will this camera work with other brand DVRs? A: Yes, it could work with most brand DVRs, please make sure the DVR resolution and signal type is proper. Q: I have an SDI system, is this compatible? A: No. Q: How to reset camera when accidentally change NTSC to PAL and signal is gone A: Change DVR from NTSC to PAL, the signal will be back, then change the camera from PAL to NTSC by OSD menu, then change the DVR from PAL to NTSC back.
Warranty and Customer Service 60-Day Money-Back Guarantee for Any Reason You may return your undamaged product and packaging within 60 days of purchase to receive a FULL REFUND for any reason. If the reason for return isn t quality-related, the customer must pay the return shipping costs. 24-Month Warranty for Quality-Related Issues Honic warrants this product against defects in workmanship and material for a period of 2 years from its original purchase date. The warranty does not cover any incidental, accidental or consequential damages arising from the use of or the inability to use this product. Any costs associated with the fitting or removal of this product by a tradesman or other person or any other costs associated with its use are the responsibility of the end user. This warranty applies to the original purchaser of the product only and is not transferable to any third party. Unauthorized end user or third party modifications to any component or evidence of misuse or abuse of the device will render all warranties void. For any further question, please contact Honic service team: Service Email: service@honictech.com Tech Email: support@honictech.com Tech support Skype ID: service@honictech.com