LED Programmable Interval Timer Owner's Handbook TF-ML2003/TF-ML2003A Born for sports,count for you
Maintenance All products are has one year warranty. Related provisions are as below: 1. 2. During the warranty period, we provide repair service for free (except man-made damages).remember to offer valid proof of purchase or purchase information when repairing, we may refuse to repair if you cannot provide valid proof of the purchase time. This warranty service does not include: (1). The components of all products are fragile, corrosive, cracked, burning, concavoconvex, destroyed, incomplete and other surface damage by man made. (2). Accident by man made, carelessness, immoderate input voltage, improper installations or operations, damages by repairing or changing the product without authorization, and direct damages or consequential damages caused by using the improper equipment or operating the equipment improperly. (3). Customers can not provide valid proof of purchase or the warranty information is not correct. If the products can be judged as what can be repaired by our company, we will replace the damaged components and parts, and collect the repair fee after customers agree to. All the damaged components and parts belong to our company. (4). If the products or the components is not longer produced, we may refuse to repair. (5). If there comes any disputes, our company has the rights of interpretation for them above. Preface Thank you for choosing our LED programmable interval timer for your athletics complex. We are confident that your new programmable interval timer will give many years of reliable service. The following manual will give some introductions about the key features, specifications, timer operation and warranty. Make sure read the manual carefully before operation. -13- -2-
The timer will beep three times to indicate that program is being saved and return to clock (9). Once a program is saved simply press the function Key and OK to begin the program. For example, when you pressing the function key it will display as follows and then you can press ok to start it. (10). The timer will beep once to start each work cycle and twice to start each rest cycle. 5.Preprogrammed Fight Gone Bad Function a). Press the F3 key b). The timer will display c). The timer will execute a 10 second count down and then proceed through the entire FGB interval beeping once to begin each new movement and twice for each rest period. 6. 10 seconds countdown Press F12 to activate/deactivate the 10 seconds countdown, 10 indicates active -4- -11- Product Introduction 1.Application Area This timer is mainly designed for Crossfit training, it also has many various functions that make it beneficial to virtually any type of exercise program. 2.Feature (1). High visibility and brightness. (2). Low power consumption, with a long battery life. (3). The remote control operation, convenient and quick. (4). Can set multiple timing scheme. (5). A wide range of applications. (6). Medium-sized,convenient to assembly and accommodate easily. Product Functions (1). Clock Display, 12/24 Hour Display Format. (2). Counting up Function,0:00 To 99:59 Minutes. (3). Stopwatch Function(Max 100 minutes, counting up with minutes, seconds and 1/100 second). (4). Quick Count down from 20:00 To 00:00. (5). Fight Gone Bad Timer (17min = Work time 5min + Rest time 1min)*3 Rounds. (6). Custom Interval Function, two intervals can be set maximum 99 rounds. (7). Preparation time Function: Activate or deactivate the 10 seconds
3.Counting Down Quick count down from 20:00 to 00:00 (1). a). Press F2 and then OK. ( you may need to press Exit first if you are already in another program) b). The timer will execute a 10 second count down to start the program then will begin counting down from 20:00. The timer will continue to count down to 00:00 unless a change is made. (2). Setting a custom count-down from time a). Press the button ( you may need to press Exit first if you are already in another program) b). The timer will display as the picture above. c). Use the and keys to move from minutes to seconds. d). When the numbers blink use the number keys (from 0 to 9) to adjust the time. e). Press OK to begin the program. The program will start with a 10 second count down. Or press one of the Function keys between F5 and F11 to save the program. The timer will beep three times to indicate that the program is being saved and return to clock f). Once a program is saved simply press the Function key and OK to begin the program. [Pause]Button:This key is used to stop. [ ]UP Button:This key is used to custom the counting up timing [ ]DN Button:This key is used to custom the counting down timing [ ] Button: This key is used to set Hour parameter in Clock Mode/ set the Minute parameter in Counting Timing [ ]Button:This key is used to set Minute parameter in Clock Mode/ set the Second parameter in Counting Timing [OK]Button:This key is used to confirm and Start. [Exit]Button:This key is used to exit. [Select]Button:This key is used to custom the counting down parameter for programmed Fight Gone Bad timer. [F1]Button:This key is used to enter into 100 Minutes counting up [F2]Button:This key is used to enter into 20 Minutes counting down [F3]Button:This key is used to enter into Fight Gone Bad timer [F4]Button:This key is used to Stopwatch [F5 F11]Button:This key is used to save the custom parameter. [F12]Button:This key is used to activate or deactivate 10 seconds counting down in preparation time function. [0 9]Button:This key is used to set the parameter data. -6- -9-
Preface Open-Package Inspection Safety Warning Product Introduction Product Functions Technology Specification Buttons Operating Guidance Maintenance Warranty Table of Contents 2 3 3 4 4 5 5 7 13 14 Warranty All products has one year warranty from the date of invoice. During the warranty period, we provide repair service for free (except man-made damages). This warranty does not include shipping cost, labor charges incurred in the removal of component parts, service calls, or damages resulting from importer installation, improper operation, or problems caused by any repair, alteration or modification of the products not performed by us. Equipment which is subjected to accident, neglect, abuse, misuse or other natural disasters, including but not limited to fire, wind, lighting, or flood, is not covered by this guarantee. -1- -14-
Open-Package Inspection Please confirm the following before start using: Is the product damaged? Is the logo of this product the same as what you order? All the products from we are tested strictly one by one when producing and packing. If there is anything wrong, please contact us or your supplier as soon as possible. Safety Warning 1. Safety Definition 7. Wireless remote control unit when you operate the remote unit, please reference to the key s indicating as Figure 1. DANGER CAUTION NOTICE Dangerous:It will damage the operator s and users personal safety if not according to the guide manual s operation. Notice: It will damage the product or can not work if not according to the guide manual's operation. Instruction: It shows how to use the product correctly and bring better effect if according to the guide manual. 2. Notice DANGER CAUTION NOTICE Do not let the screws, shim and other metal objects inside of the brake unit. It is easily damage the scoreboard. Make sure the case cover is closed when operating. Do use the original power adapter. Figure 1-3- -12-
Technology Specification Buttons counting down in all kinds of timing models. (8). Max Save 7 sets of custom data information. (9). Wireless Remote. Apparent Size: 655* 173* 50(mm) Color: Black N.W: 1.50kg Display: 6 digits display Light-emitting Device: high visibility red & green LED Working Voltage: 12.6VDC Working Current:1A Power Supply Method: TF-ML2003 External Power adapter 12.6V 1A, TF-ML2003A Internal Lithium Battery 12V 2200mAH, with a charger 12.6V 1A Battery Charing Time: 3 Hours Battery Usage Time: 2 Hours Wireless Remote Distance: 15m, Remote Battery Spec: 1.5V, 2xAAA Battery Working Environment Temperature Range: -10C~50C Relative Humidity: 85% Protection Class: IP52 [Power]Button: This key is used to power on/off. [12/24H]Button: 12/24 Hour Format Shift. [Restart]Button: This key is used to start again. 4.Creating Custom Intervals (1). Press the select button (you may need to press exit first if you are already in another program). (2). The timer will display the number of Rounds in Blue. Press the number keys to select the number of times you wish to go through the entire interval from 1 to 99. (3). Press select again and the timer will display (4). H1 represents the amount of time the athlete will work. (5). Use the and keys to move from minutes to seconds. When the numbers blink the number keys (from 0 to 9) can be used to adjust the time. (6). Press select again and the timer will display as above. H2 represents the amount of time the athlete will rest. (7). Use the and keys to move from minutes to seconds. When the numbers blink the number keys(from 0 to 9) can be used to adjust the time. (8). Press OK to begin the program. The program will start with a 10 second count down. Or press one of the Function keys between F5 and F11 to save the program. -5- -10-
Operating Guidance 1.Setting the time of day (1). Clock Display a).press or to select the minutes or hours to be changed. b). When the number blink use keys from 0 to 9 on the remote to change the time ( for example, change the time to be 12, you need to press the first key 1 and then press the second key 2 ). c). Press OK to confirm the changes. d). Alternate between 12/24 hr format by pressing 12/24H. 2.Counting up (1). Quick Count Up from 0:00 to 99:59 Press the F1 and then OK (you may need to press Exit first if you are already in another program) The timer will execute a 10 second count down then will count up from 0:00 to 99:59. (2). Stopwatch Function (100 minute max count-up with minutes, seconds, and hundredths of a second). a).press F4 the timer will display b). Press OK. (you may need to press Exit first if you are already in another program) The timer will immediately begin counting up from 00:00:00. The timer will continue to count up to 99:59:00 unless a change is made. (3). Setting a custom count-up to time. Press the button (you may need to press Exit first if you are already in another program). b). The timer will display c). Use the and keys to move from minutes to seconds. d). When the numbers blink use keys from 0 to 9 on the remote to change the time for example, change the time to be 12, you need to press the first key 1 and then press the second key 2 ). e). Press OK to begin the program. The program will start with a 10 second count down. Or press anyone of the Function keys from F5 and F11 to save the program. The timer will beep three times to indicate that the program is being saved and return to clock f). Once a program is saved simply press the Function key and ok to begin the program. -7- -8-