DRAFTS IN WIDE CIRCULATION DOCUMENT DESPATCH ADVICE Ref. Date MED 7 /T- 191 02 01 2019 Material Handling Systems and Equipment Sectional Committee, MED 07 1) All Members of Mechanical Engineering Division Council 2) All Members of Material Handling Systems and Equipment Sectional Committee, MED 07 3) All other interested members Dear Sirs, MED 07 ( 13435) Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and components (Adoption of ISO 6016:2008) Kindly examine the draft standards and forward your views, stating any difficulties which you are likely to experience in your business or profession, if they are finally adopted as National Standards. Last date for comments: 05 03 2019 Comments, if any, may please be made in the format as given overleaf and mailed to the undersigned at the above address. In case no comments are received or comments received are of editorial nature, you will kindly permit us to presume your approval for the above document as finalized. However, in case of comments of technical in nature are received then it may be finalized either in consultation with the Chairman, Sectional Committee or referred to the Sectional committee for further necessary action if so desired by the Chairman, Sectional Committee. This document is also hosted on BIS website www.bis.org.in Thanking you, Yours faithfully, Encl.: As above (Rajneesh Khosla) Sc `E & Head (MED)
व य पक प पक च ल म द दर भ टद न र वमईड 7/ 191 02 01 2019 म ट र यल ह डलल ग ल स म वमम पकर वमषय लमत, वमईड 7 प र ष त : 1 य त र प इ ज तमय ष भ ग पक च प दभ द स य 2 ट च य ह डल ग लदस व पपक प ष य दल त, व ईड 7 प दभ द स य 3 र चल खम अन य तमप य
ह य, तमम मल ख मप प द द ग म ह : प रल ख ख य व ईड 7 (13435) श षभर -द ल म श म - पक श म, पमप पपक प व अ य प ओ प पक म प पक द धत य [आईवदओ 6016:2008 प अच ग रह ] प पकय इम द प अ पम प औ अपकम दम त य यह त हएव भ प अ : यट य मप ष ट र य मप प र पक प रप लश ह इम पक अ प म आपकप व य द य अव प त य पट म ईय आ दप ह दम त य भ म प अजन त चव 05 03 2019 दम त यट प ई ह प पकय अ हस क षर प पपक ल ख पक पक द ग म मट भ य ई प यट प ई दम त प र मह ह ह अव दम त प भ द त एट हएई पपक प र ख प यव अ त र पक ट य य ग यट प ई दम त पम प प रप त प हएई ष य दल त प अ यक षर प पक शमट द अव पमप इच छ पक आग प प यमट ह प ल व ष य दल त प भ म प त प र ख प अ त र पक ट य वग यह प र ख भ य मप ब य प तद इ www.bis.org.in पक भ पपक ब ह न य, भ य, ल रग न : पक ललखख ( जन श ख ल ) म ज ञ तनर `ई वम प रम ख (वमईड )
IS/ISO 6016 : 2008 Doc: MED 07(13435)c For Comments Only भ रत य म नक मस द म द -स च लन मश नर - प र मश न, उनक उपकरण एव अवयव क म त र ओ क म पन क पद धततय [आईएसओ 6016:2008 क अध ग रहण] Draft Indian Standard Earth-moving machinery Methods of measuring the masses of whole machines, their equipment and components (Adoption of ISO 6016:2008) ICS 53.100 Not to be reproduced without the permission of Last date for receipt of BIS or used as a STANDARD comments is: 05 March 2019 NATIONAL FOREWORD (Adoption clause to be added later on). In the adopted standard certain terminology and conventions are not identical with those used in Indian Standards; attention is drawn specially to the following: a) Comma (,) has been used as a decimal marker while in Indian Standards the current practice is to use a point (.) as the decimal marker. b) Wherever the words International Standard appear, referring to this standard, they should be read as Indian Standard. In the adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The corresponding Indian Standards which are to be substituted in their places are listed below along with their degree of equivalence for the edition indicated: International Standard Corresponding Indian Standard Degree of Equivalence
IS/ISO 6016 : 2008 Doc: MED 07(13435)c ISO 6165:2006 Earthmoving machinery Basic types Identification and terms and definitions ISO 9248:1992 Earthmoving machinery Units for dimensions, performance and capacities, and their measurement accuracies IS/ISO 6165:2012 Earth-moving machinery Basic types Identification and terms and definitions IS/ISO 9248:1992 Earth-moving machinery Units for dimensions, performance and capacities, and their measurement accuracies Identical with ISO 6165:2012 Identical For the purpose of deciding whether a particular requirement of this standard is complied with, the final value, observed or calculated, expressing the result of a test or analysis shall be rounded off in accordance with IS 2:1960 Rules for rounding off numerical values (revised). The number of significant places retained in the rounded off value should be the same as that of the specified value in this standard. FOR COMPLETE TEXT PLEASE REFERE TO ISO 6016: 2008. IF ANY ONE REQUIRES A HARD COPY OF THE SAME PLEASE CONTACT THE UNDER SIGNED. Rajneesh Khosla Sc-E and Head (Mechanical Engineering Department) Manak Bhavan 9 Bhadurshah Zafar Marg New Delhi 110002 Telefax 011-23232509 Email: med@bis.org.in
FORMAT FOR SENDING COMMENTS ON BIS DOCUMENTS (Please use A4 size sheet of paper only and type within fields indicated. Comments on each clauses/subclauses/table/fig. etc be started on a fresh box. Information in Column 4 should include reasons for the comments and suggestions for modified wording of the clauses when the existing text is found not acceptable. Adherence to this format facilitates Secretariat s work) It is desirable to send comments through email at : med@bis.org.in. IS. No./ Doc. No.: TITLE : NAME OF THE COMMENTATOR /ORGN.: Sl. No. Clause/Subclause/ para/table/fig. No. commented Comments Justification Proposed change