SERVICE TIPS BEFORE CALLING FOR SERVICE,HAVE YOU CHECKED( )THE FOLLOWING CHART BRAND: SIZE: MODEL: ON SYMPTOMS AND SOLUTIONS? AUDIO OUTPUT POWER SOURCE: RATED POWER CONSUMPTION : 115 W ORIGEN : COLOR SYSTEM: SOUND SYSTEM: AV INPUTES: BAND WIDTH: Symptoms CAIRA CRT 29" CA-S5029 2x4W RMS 90-260V ~ 50/60HZ MADE IN CHINA PAL,NTSC D/K,I,B/G 3LINE No picture,no sound Poor sound,picture OK Poor picture,sound OK Weak picture Blurred picture Double image VHF-L 48.25MHz 161.25MHz VHF-H 168.25.25MHz 463.25MHz UHF 471.25MHz 855.25MHz Lines in picture Distorted picture Weak reception on some channels Horizontal bars Picture rolls vertically Poor colour No colour Misoperation of Remote control No Remote control Solution On screen Display Control outside the screen Try different channel,if OK,probably station trouble Check aerial connectiions on back of set Check aerial for broken wires Re-orient aerial(if indoor type) Probably local interference,such as an appliance Adjust fine tuning control Adjust brightness control Adjust contrast control Check if station is broadcasting colour Adjust colour control Check if system switch is correct Check if on/off switch is on Check Batteries in Remote control COLOUR TV ON SCREEN DISPLAY REMOTE CONTROL HYPER BAND TUNER AUDIO/VIDEO-IN/OUT CA-S5029 Instruction Manual 7BE7-H445
SPECIFICATIONS BATTERY INSTALLATION(REMOTE CONTROL UNIT) Picture Tube Ext. Antenna Audio Output Power Auto Voltage Power Consumption Dimension (L B H) Net Weight 37cm~87cm(14 ~34 ) diagonal 75 Ohm Coaxial Cable 14 21 2.5W 2 25 29 4W 2 34 5W 2 Refer to the Back Plate of TV Unit 14 = 65W 21 = 75W 25 = 105W 29 = 115W 34 = 135W 14 450(W) 410(D) 378(H)mm 21 580(W) 515(D) 520(H)mm 25 750(W) 528(D) 560(H)mm 29 840(W) 570(D) 650(H)mm 34 975(W) 670(D) 765(H)mm 14 (11kg) 21 (24kg) 25 (30kg) 29 (38kg), 34 (65kg) 1.Remove the battery cover. 2.insert the 2 UM-4 AAA 1.5V batteries making sure the polarity(+or -)of the batteries matches the polarity marks inside the unit. 3.Replace the battery cover. Replace with new batteries when the TV set begins to show the following symptoms: operation is unsteady or erratic. Sometimes the TV set does not function with Remote control unit. Remark: 1) Alkaline batteries recommended. 2) Remove batteries when they are exhausted or if the remote control is not to be used for a long time. WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like. REMOTE CONTROL Transmitting System: infrared Power Supply : DC 3V AAAX2 Battery Design and specifications are subject change without prior notice For the sake of safety and saving electricity, Please do not use the remote controller to switch off TV when not watching it. When you leave, please pull out the power plug. Incorporated in your TV receiver are the most up-to-date devices to eliminate interference. Local radiation however, can create disturbances which Visibly affect your picture. Proper installation, a good aerial are your best safeguards against these disturbances. INTERFERENCE Moving ripples across the screen are caused by nearby transmitting or receiving shortwave radio equipment. THE CAUSES OF INTERFERENCE SNOW Weak TV signals from long distant stations result In an unsteady picture and give the effect of falling snow. An antenna adjustment or antenna amplifier may be needed. GHOST Multiple images caused by TV signals reflected back from surrounding buildings, hills, aircraft, etc. are minimized by correct aerial positioning. NOTE Product function described by specifications takes material object as the standard concretely if having slight difference with material object DIATHERMY Herringbone pattern and partial picture loss can result from the operation of diathermy equipment from a nearby doctors surgery or hospital. CAR IGNITION Nearby cars and electrical motors can cause small streaks across the picture or make the picture roll. -1- -14-
11.PICTURE FORM BUTTON You can select any one of the following form by pressing P.P button repeatedly. 12.SYSTEM CHOOSING BUTTON Sound system setting Press SYS button, sound Menu will appear. Then you can select DK, BG or I for sound system by pressing V+/V- button. 13.MAIN MENU BUTTON When press the main menu button, TV displays as follow in turn: 14.CHANNEL INCHING BUTTON The function of this button is the same as that of P+ and P- buttons on the panel. 15.VOLUME BUTTON The function of this button is the same as that of V+ and V- buttons on the panel. 16.AUDIO BUTTON Press AUDIO BUTTON to enter audio function mode. the picture cut off in this mode, only have sound. Press this button again with exit audio function mode. return to the normal watching mode. 17.GAME MENU BUTTON Press GAME BUTTON to enter game operation interface. [MENU] Key [V+/V-] Key STANDARD MILD VIVID DYNAMIC PERSONAL start / exit. select class. SOUND DK SPECIFICATIONS Thank you very much for your purchase of this product-the most natural Colour Television Receiver. To enjoy your set to the full from the very beginning, read this manual carefully and keep it handy for ready reference. INSTALLATION Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is Recommended for comfortable viewing. Allow enough space between the receiver and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature component Failure. This TV receiver can be connected to AC power supply. Never connect to DC supply or any Other power supply. Do not install the receiver in a location near heat sources such as radiator, air ducts, direct sunlinght, or in a place somewhere like close compartment and close area. Do not cover the ventilation openings when using the set. NOTE Do not use this apparatus near water, the apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION Never tamper with any components inside your set,or any other adjustment controls not mentioned in this manual. All television receivers are high voltage instruments. Your PICTURE TUBE is highly evacuation. lf broken, glass fragments will be violently expelled. Scratching, chipping or undue pressure is dangerous and should be avoided. When you clean up dust or stick of a water drop on the PICTURE TUBE FACE or CABINET. the power cord should be pulled out form the plug receptacle, then wipe the receiver with dried soft cloth. During thunder and linghting, unplug the power cord and antenna cord to prevent your TV set from damage. All inside work on your receiver should be performed only by the TV Service personnel. IMPORTANT INFORMATION If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as: Using cabinets or stands recommended by the manufacturer of the television. Only using furniture that can safely support the television. Ensuring the television is not overhanging the edge of the supporting furniture. Not placing the television on tall furniture (for example,cupboards or bookcases) without anchoring both the furniture and the television to a suitable support. Not standing the televisions on cloth or other materials placed between the television and supporting furniture. Educating children about the dangers of climbing on furniture to reach the television or its controls. -13- -2-
Important Safety Instructions Operation of Remote Controller Don't put the TV near humid metope, water and oils; otherwise, it may catch a fire. Don't use damaged power plug, don't put the power cord close to the heat source, otherwise, it may result in electric shock or fire. During rainstorm and thunderstorm, don't use the TV and unplug this TV and its antenna from the wall outlet. Don't disassemble the set by unqualified personnel. In case of trouble, refer all servicing to qualified personnel. It may result in electric shock or fire if being disassembled by unqualified personnel. 1.POWER STAND BY When press down this button, TV switches on. When press this button again, TV has entered the stage of stand by. 2.MUTE BUTTON When press this button, switch off the sound and press it again, recover the sound. 3.TV/AV SWITCH BUTTON When press this button, the TV and AV systems can change each other. 4.CHANNEL-CHOOSING BUTTON Press down 0 to 9 buttons to choose one digit channel (0-9). 5.BACK BUTTON When press this button, the last and present channels can change each other. 6.TWO OR THREE DIGIT BUTTON When press the two or three digit button, the screen displays -- and choose the number or digits you want for the channel. 7. FAVORITE CHANNEL BUTTON Press this key to fast browse your favorite program. 8.SLEEP TIMER BUTTON When press this button, the sleep time can be set as follows (by minute)when sleep time is set, the switch-off time will be cleaned off automatically. the sleep time setting will be cancelled automatically if you set sleep time. Don't locate the power transformer in the vicinity of heat source, or it may result in fire. Don't rub or knock the screen with a hard object that may scrape or damage it. When cleaning, unplug the set from the power outlet, use soft cloth for cleaning, and don't use industrial chemicals. Care shall be taken not to allow water to flow into the set. Cut-off the power supply for long time of no use, or it may result in electric shock or fire. Note: We will not notify customers particularly when there is any change happened in the design and specification of the product. The pictures in the handbook may bear slight differences from the real one. Please take actual products as the standard. OFF 120 110 100...30 20 10 9.SELECT BUTTON Press this key to set the current program as the favorite program. And then the colour of the "program no." will be change to yellow. It can be set 8 favorite program. 10.SCREEN DISPLAY BUTTON When press this button, the screen displays the present channel number, color form, sound form, time and leaving time (Leaving time must be set in advance). -3- -12-
Remote Controller Connection to Other Equipment This TV set can be connected to videotape player, videodisc player, video camera, game player or audio player. X Front AV terminal VCD PLAYER 1 2 3 4 5 6 7 8 9 0 AV P.P SLEEP P+ V- V+ P- SYS GAME DISP SCAN AUDIO SELECT NOTE: Video/Audio equipment can be connected to sockets of AUDIO IN or VIDEO IN in rear. Back AV terminal DVD PLAYER L R V OUT L R V IN Cb Cr Y VIDEO OUT R AUDIO OUT L IN RF OUT AC220V TV NOTE: Since the same sound channels are provided for both YUV and AV1, only either of them may be used at a time. As the default setting of the unit, YUV channels have precedence over those of AV1. (Applicable to 8897/8899.) -4- CHILD LOCK FUNCTION (optional) Pressing and holding (DISP)key for more than 5 seconds, all the keys except (DISP) key and ( ) key are locked, then pressing and holding (DISP) key for more than 5 seconds, all the keys the face panel are unlocked. Don't mix different battery types. Take out of the batteries from the remote for long time of no use. -11- Cb Cr Y VIDEO OUT R L AUDIO OUT
CONTROL LOCATION For control knobs (all panels subject to the real object), please refer to your own TV set. Front and Back Control Panel 6.3 Calendar OPTION Press "P+" button to choose the item of calendar. Press "V+" button to open the item of calendar. Press "V+/V-" button to choose year, month and day. Press "P+/P-" button to choose year calendar, month calendar and day calendar. When language used is Chinese, traditional Chinese calendar may also be displayed. 6.4 Screen Protection OPTION To choose screen protection or not in case of no signal, press "V+/V-" button to switch between "ON" and "OFF". 7. Menu of Sound Setting Press "MENU" button to enter sound menu. Press "P+/P-" button to choose the item to be adjusted. 1. Speaker 2. Side AV In (Option) 3. AV/TV 4. Menu Button 5. Volume Down Button 6. Volume Up Button 7.Program Down Button 8. Program Up Button 9. Power Indicator 10. Remote Sensor 11. Main Switch 12. Speaker 13. AC power Cord 14. Audio/Video-in/out 15. Terminal Antenna(75 Ohm) Automatic Preset Channel 1) Sound Press "V+/V-" button to adjust the volume. The parameter may be adjusted in the range between 0 and 100. 2) Balance OPTION Press "V+/V-" button to adjust the balanced sound. The parameter may be adjusted in the range between -50 and +50. SOUND VOLUME 57 BALANCE 00 AV IN TV/AV MENU V- V+ P- P+ Press "MENU" button and let the arrow point to"automatic Search" function and then press V+button starting to search the channels automatically. -10- -5-
5. Channel Edition Press"MENU"button to choose "SEARCH" menu. Press "P+/P-" button to go to paging and to enter "CHANNEL EDITION" menu. Press "V+/V-" button to adjust the current menu option. POS EDIT CURRENT POS 000 TARGET POS 000 5.1 Position Setting CONFIRM 1) Press "P+/P-" button to choose SKIP OFF "CURRENT POSITION"/TARGET SOUND DK POSITION. Press "V+/V-" button to SEARCH choose current program. 2) Press "P+/P-" button to choose "CONFIRM" option. Press "V+/V-" button to confirm it. Now OK is displayed on the screen and the tune is completed. Operation of Function Menu After TV set has been put in place, connect antenna or cable antenna to the socket and switch on TV. When picture and sound appear, press P+ or P- for choosing a desired program and V+ or V- for adjusting volume. If a blue screen appears, press CHANNEL-CHOOSING button on the remote controller and then press CHANNEL button to let the arrow point to automatic search function, and then press VOLUME button for searching. This TV set can memorize the number of channels from 0 to 248. After searching, the TV stops at the channel 0 and is ready for watching. 5.2 Sound System Press "P+/P-" button to enter the option of sound system. Press "V+/V-" button to alter the current sound system. AV IN TV/AV MENU V- V+ P- P+ D/K B/G I 6. Setting Menu Press "MENU" button to choose the FUNCTION menu. Press "P+/P-" button to choose the option to be set. Press "V+/V-" button to adjust the setting. 6.1 Language Press "P+/P-" button to choose the option of language. Press "V+/V-" button to choose the language to be used. LANG. TEMP. ALC CALENDAR SCREEN P. FUNCTION ENGLISH STANDARD OFF 6.2 Color Temperature Press "P+/P-" button to choose the option of color temperature. Press "V+/V-" button to choose various effects of color temperature. There are 3 options as follows: ON OPERATION INSTRUCTIONS OF PANEL First insert power plug and then insert antenna or cable antenna into the socket of antenna. SWITCH ON AND OFF TV When press down Power button, power is connected. When press down Power button again, power is off. When TV is at stage of sleep, it can not be switched on or off by pressing the power button. NOTE: When TV is at stage of sleep, it can be switched on or off by pressing the sleep button on the remote controller. CAUTIONS: In case that electricity is cut when watching TV, switch off the power. If TV is not watched, please switch off the power. When TV is at stage of sleep, there is a part of circuit working and consuming electricity. STANDARD COOL WARM -9- -6-
1.Main Menu Operation of Function Menu 1. 1 Press MENU key, menu will appear, as shown in the right figure. PICTURE TIMER SEARCH FUNCTION SOUND 1.2. Select from the following five Items by pressing MENU key. 3. Image Setting Press "MENU" button to choose the menu of "PICTURE". Press "P+/P-" button to enter the option of image setting. 3.1 Press "P+/P-" button to choose the option to be adjusted. 3.2 Press "V+/V-" button to adjust the content of the option. In this menu, the luminance, contrast, color, quality and noise reduction may be adjusted by pressing "P+/P-" button directly. Note: TINT will be displayed only in NTSC system. PICTURE BRIGHT 50 CONTRAST 50 COLOR TINT 50 00 SHARP 50 NOISE REDU. OFF 2. Search Menu SEARCH 2.1 Automatic Search 1) Press "P+/P-" button to choose the option of automatic search. (Or press "MENU" button on the panel for 5 seconds to enter the state of automatic search.) 2) Press "V+" button to start automatic search. Press "V-" to stop automatic search. 3) It will return to "0" automatically after the end of automatic search. UHF V-L V-H SEARCH POSITION 099 BAND V-L MFT SEARCH AUTO TUNE 2.2 Manual Search 1) Press "P+/P-" button to choose the option of manual search. 2) Press "V+/V-" button to start manual search. 3) Each program found in search will be stored in TV position. 2.3 Wave Band 1) Press "P+/P-" button to choose the option of wave band. 2) Press "V+/V-" button to switch wave band. 4. Time setting Press"MENU"button to choose time option. Set the appropriate time based on 24 hours system. 4.1 Clock Adjustment 1) Press "P+/P-" button to choose the option of time. 2) Press "V+/V-" button to set the current time. (Holding "V+/V-" button will increase/decrease the clock by ten minutes.) TIME CLOCK 0:07 OFF TIMER OFF 0:00 ON TIMER OFF 0:00 POSITION 0 4.2 ON Timer/OFF Timer 1)Press "P+/P-" button to choose the option of "OFF TIMER" Press "V+/V-" button to set the OFF TIMER mode same day or every day 2) Press "P-" button choose the option of OFF TIMER mode same day or every day 3) Press "V+/V-" button to set the time for turning off the unit. (Holding "V+/V- " button will increase/decrease the clock by ten minutes.) 4) Set the time for turning on the unit in the similar way. 4.3 Position 1) Press "P+/P-" button to choose the option of position. 2) Press "V+/V-" button to adjust the position. The position now set is the default position for timing on. -8- -7-