CEDAR Series The CEDAR platform has been designed to address the requirements of numerous signal processing modules. Easily-installed components simplify maintenance and upgrade. To learn more about Ogden CEDAR series signal processing platform and modular products, please visit www.ogdentec.com.
CEDAR Series High-Performance Wideband Signal Processing Platform CEDAR is a reliable wideband signal processing platform featuring flexible configurations. It supports 1RU and 2RU frames. CEDAR provides power supply, HD/SD video sync reference and audio sync reference for all the internal modules. Multiple control interfaces include LAN and RS-232/422. It is equipped with LCD display and buttons on the front panel for status indication and control. CEDAR uses front-pluggable power supply unit, control module and rear-pluggable functional modules. With easily-installed components, CEDAR can be maintained and upgraded easily. CEDAR supports redundant power supply. The internal cooling assembly is controlled by a temperature detector located in the frame center. It creates a safe and reliable operating environment for the modules. CEDAR uses dual built-in video synchronization signal generators and dual audio synchronization signal generators. Video and audio sync clock signal on each channel is associated with genlock unit. This design contributes to interference suppression and clock jitter reduction. CEDAR uses redundant design for the generator and the genlock unit; one primary and one backup. The platform detects the operating status of the primary and backup units on a real-time basis and performs auto-switching when necessary. CEDAR distributes sync signals to modules in the frame. The modules can then separately pick up the desired signals according to the supported signal system. The frame and modules can be controlled through the local front panel which is equipped with LCD display and status LEDs. CEDAR uses built-in RS-232/422 Hub and Ethernet Switcher that directly interface with the modules. This design provides transparent transmission for signals and eliminates protocol nonconformity. CEDAR, as an A/V signal processing platform used in the broadcasting and TV industry, can hold numerous HD/SD video and audio modules. Various module functions include keying, logo generation, emergency switching, audio processing, up/down switching, embedding, de-embedding, distribution, frame sync and signal conversion. Structure Frame: 1RU (4 slots), 2RU (8 slots) Redundant and hot-swappable power supply units available in 2RU frame Front-pluggable control module and power supply units, easy to maintain and upgrade Rear-pluggable and hot-swappable functional modules, easy to maintain and expand Unique built-in cooling system Dual internal detection points for real-time temperature monitoring LCD display and operational buttons on front panel Communication Multiple serial ports supporting RS-232 and RS-422 control protocols Built-in serial port hub, making access of any modules available Built-in 10M/100Mbps-based Ethernet switcher LAN interface, providing transparent transmission of module status and signals Sync Dual sync reference inputs supporting HD/SD video, AES3 and Word Clock Distributes reference signals directly to slots Sync signal generator can select any reference source Both video sync signal generators can generate sync sequence signals, such as H, V, ODD/EVEN and Lock; and also sync clock signals, such as 27/67.5MHz (SD) and 74.25/74.176/148.5/148.35MHz (HD) Both audio sync signal generators can generate audio sync clock signals, such as 3.072MHz,12.288MHz and 48KHz Video and audio sync clock is associated with gunlock unit, provides low jitter and high precision Redundant sync signal generator and genlock unit Each frame slot can pick up any video or audio sync signal individually Miscellaneous LCD and buttons control both the frame and the modules LED indicators for each slot, indicating module presence and status Multiple indicators for fan, temperature, power supply unit, LAN interface and external reference source Various alarm indicators 132 Ogden Technology Corporation An Expert in Signal Management
C CEDAR Series High-Performance Wideband Signal Processing Platform FRONT PANEL MENU ENTER OK CE SYS MENU ENTER OK CE SYS 1. Indicators 2. LCD 3. Navigating menu 4. MENU button, CE button and ENTER button 5. Module select button and status indicator 6. Frame system select button and indicator BACK PANEL C 1. Dual power supply connectors 2. Dual sync REF input connectors 3. Ethernet connector 4. RS-422 serial ports 5. RS-232/422 serial port 6. Various functional modules www.ogdentec.com Technical Support: support@ogdentec.com 133
CEDAR Series High-Performance Wideband Signal Processing Platform Mechanical Width 19 in. (483 mm) Height 1RU (44 mm) 2RU (88 mm) Depth 21 in. (531.5 mm) Electrical Power Supply 100 ~ 240 V AC ±10%, 47 ~ 63 Hz Power Consumption 80 W ( 2) for 1RU 150 W ( 2) for 2RU Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Connector REF IN BNC ( 2) LAN RJ-45 ( 1) RS-232 DB-9F ( 1) RS-422 DB-9F ( 1) for 1RU DB-9F ( 2) for 2RU REF Signal SD Video NTSC / 525I (SMPTE 125M/267M) PAL / 625I (ITU-R BT.601-5) 525P / 59.94 (SAMPTE 293M) 625P / 50 (ITU-R BT.1358) HD Video SAMPTE 274M, SAMPTE 296M Audio AES3 48 khz Word-Clock 96 khz Word-Clock 192 khz Word-Clock LAN IEEE802.3 CD-MASTER CEDAR Series Platform Control Software CD-MASTER is a system control application designed for CEDAR High-Performance Wideband Signal Processing Platform. It is compatible with various module applications. CD-MASTER provides intuitive graphical interfaces for operating status display and module control. Users can choose frame-based, module-based or user-defined control interface. It supports configurable software. No upgrading is needed when new applications are added. CD-MASTER is designed to run under Windows Operating Systems. It interfaces with monitoring computer through switch or hub within a special LAN; it can also interface with other CEDAR platforms on an open network through a router. Dedicated control program for each signal processing module in CEDAR series Programmable configuration, supports addition of new applications It has group system configuration, new module does not need to be upgraded individually Supports TCP and SNMP protocols, remote diagnose and monitoring available Provides various user-friendly monitoring interfaces, such as Frame Management and Module Management Supports Central Management, one-screen monitoring for multiple modules Supports status alarms and records, event log checking Frame Management The right section of the interface shows frame information. The upper section is the frame view, including power supply, fan and modules. The middle section shows frame information and configuration area, including platform information, alarm and reset operation. The lower section shows module details. CD-MASTER displays the status of the platform via Frame Management interface. The left section of the interface shows the list of the frames, and the content below the frame name is the list of each function module. Three colors are used for LED indicators representing Normal, Alarm and Fault status. The Frame Management interface will automatically refresh and display the newest status when frame information changes. 134 Ogden Technology Corporation An Expert in Signal Management
CD-MASTER CEDAR Series Platform Control Software Module Management address information and activate its control program. The Module Management interface will automatically refresh and display the newest status when frame information changes. The module list displays each module's model number and name of input and output signals. CD-MASTER displays the status of the modules via Module Management interface. The left section of the interface shows the list of modules placed in the frame. The list can be arranged based on frame IP address or module type. In Module Management interface, users can check each module's Centralized Control Event Log CD-MASTER can simultaneously monitor status of multiple modules via Centralized Control interface. Users can add or reduce control interfaces as needed. Module control window's size and location are adjustable. When an interface is closed, the location and size of its module window will be automatically saved. Module control windows provide complete control for each module's parameters, status and setting, and displays real-time status information. CD-MASTER provides Event Log interface for alarm and status information checking of CEDAR equipment. Event log can be checked and selected via event time, equipment address and event type. The system automatically saves the record information of the latest year. ORDERING INFORMATION CD-FM-1RU CD-CB CD-PWR CD-FM-2RU CD-CB CD-PWR 1RU CEDAR series frame Control module Power supply 2RU CEDAR series frame Control module Power supply www.ogdentec.com Technical Support: support@ogdentec.com 135
CD-DSK SD-SDI Dual-Channel Downstream Keyer network monitoring function of CEDAR. Its various parameters can be configured and adjusted through CEDAR router and the supporting control software which can also monitor the operating status and signal status of the module. CD-DSK is a modular SD dual-channel downstream keyer specially designed to run in a CEDAR frame. It supports 2-level linear keying process on input SD-SDI digital video graphics. CD-DSK provides t wo pairs of key & fill inputs and one program input. Both key inputs can be keyed onto the program simultaneously or individually. It supports four modes of video mixing: fade-cut, cut-fade, V-fade and cut. Transition speeds are fast, medium and slow. CD-DSK offers dual processed digital program outputs, one analog monitor output, one digital preview output and one analog preview monitor output. CD-DSK can be controlled by a programmable GPI interface or by the dedicated control panel. It supports one-button triggered bypass protection. This ensures the program can be output without interruption even when power is off. CD-DSK can be housed in a 1RU or 2RU CEDAR frame. It supports BLOCK DIAGRAM 2-level keying, hard key and transparent key available 4 selectable keying modes: fade-cut, cut-fade, V-fade and cut 3 transition speeds: fast, medium and slow Input signal line sync, auto sync with the input reference signal Reclocking and cable equalizing supported input channels Preview channel Dual analog monitor outputs Supports by-pass protection Supports CEDAR-based network monitoring Non-volatile memory Hot-swappable BACK MODULE 136 Ogden Technology Corporation An Expert in Signal Management
CD-DSK SD-SDI Dual-Channel Downstream Keyer Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Digital Video Input Signal Format SMPTE 259M-C, 270 Mbps, 525/625 component Quantization 10 bits Connector BNC ( 5) Impedance 75 Ω Return Loss 18 db @ 270 MHz Cable EQ <1000 ft (about 300 m) Belden 1694A cable or equivalent Digital Video Output Signal Format SMPTE 259M-C, 270 Mbps, 525/625 component Quantization 10 bits Connector BNC ( 3) Impedance 75 Ω Return Loss 18 db @ 270 MHz Amplitude 800 mvp-p ±10% Rise/Fall Time 400 ~ 1500 ps, 20% ~ 80% of amplitude Overshoot <10% of amplitude Jitter <0.2UI Analog Composite Video Output Signal Format CVBS Standards NTSC, PAL Quantization 8 bits Connector BNC ( 2) Power Consumption 10 W Impedance 75 Ω Amplitude 1.0 Vp-p±3% Chr/Lum Delay Diff <5 ns S/N Ratio >70 db @ 6 MHz CD-DSK-PN CD-DSK Control Panel CD-DSK-PN is a remote control panel designed for CD-DSK. It is used to perform various functions on CD-DSK, including by-pass protection, selection of key signal, keying mode and keying rate. FRONT PANEL Program preview and output can be controlled by the TAKE button. CD-DSK-PN interfaces with CD-DSK through CAT-5 cable. Remote control is available via RS-422 interface. BACK PANEL 1. By-Pass Select Button 2. Key1 Source Select Button 3. Key2 Source Select Button 4. Cut Button 5. Cut-fade Button 6. V-fade Button 7. Fade-cut Button 8. Rate Select Button 9. Execution Button 10. Double RJ-45 Connectors One acts as RS-422 control interface to connect with CD-DSK, hot-pluggable not supported; the other one is used for control panel expansion, loop-thru supported. ORDERING INFORMATION CD-DSK CD-DSK-PN SD dual-channel downstream keyer CD-DSK control panel www.ogdentec.com Technical Support: support@ogdentec.com 137
CD-DSK-HD HD/SD-SDI Tri-Channel Downstream Keyer parameters can be configured and adjusted through CEDAR s router and the supporting control software which can also monitor the operating status and signal status of the module. CD-DSK-HD is a modular HD/SD tri-channel downstream keyer designed to operate in a CEDAR frame. It supports 3-level linear keying process on input HD/SD-SDI digital video graphics. CD-DSK-HD provides 3 pairs of key & fill inputs and one program input. All the key inputs can be keyed onto the program simultaneously or individually. It supports four modes of video mixing: fade-cut, cut-fade, V-fade and cut. Transition speeds are fast, medium and slow. CD-DSK-HD offers dual processed digital program outputs and one digital preview output. 3-level keying, hard key and transparent key available, transparency adjustable 4 selectable keying modes: cut, cut-fade, V-fade and fade-cut 3 transition speeds: fast, medium and slow Input signal line sync, eradicate jitter from previous routing switcher Reclocking and cable equalizing supported input channels Preview channel, program output with keyed signals controlled by TAKE button One HD/SD-SDI preview output Supports by-pass protection Supports CEDAR-based network monitoring Non-volatile memory Hot-swappable CD-DSK-HD can be controlled by a programmable GPI interface or by the dedicated control panel. It supports one-button triggered bypass protection. This ensures the program can be output without interruption even when power is off. CD-DSK-HD can be housed in a 1RU or 2RU CEDAR frame. It supports network monitoring function of CEDAR. Its various BLOCK DIAGRAM BACK MODULE 138 Ogden Technology Corporation An Expert in Signal Management
CD-DSK-HD HD/SD-SDI Tri-Channel Downstream Keyer Electrical Power Consumption 10 W Digital Video Input Signal Standard SMPTE 259M SD-SDI, SMPTE 292M HD-SDI Quantization 10 bits Connector BNC ( 7) Impedance 75 Ω Return Loss 18 db @ 270 MHz, SD 15 db @ 1.485 GHz, SD Cable EQ <1000 ft (about 300 m), SD <530 ft (about 160 m), HD Belden 1694A cable or equivalent Digital Video Output Signal Standard SMPTE 259M SD-SDI, SMPTE 292M HD-SDI Quantization 10 bits Connector BNC( 3) Impedance 75 Ω Return Loss >18 db @ 270 MHz, SD >12 db @ 1.485 GHz, HD Amplitude 800 mvp-p ±10% Rise/Fall Time <800 ps, SD; <135 ps, HD 20% ~ 80% of amplitude Overshoot <10% of amplitude Jitter <0.2 UI CD-DSK-HD-PN CD-DSK-HD Control Panel fade-cut, cut-fade and cut-cut) and Keying Rate Selection. Program preview and output can be controlled by the TAKE button. CD-DSK-HD-PN is a remote control panel designed for CD-DSK-HD. It is used to perform various functions on CD-DSK-HD, including By-pass, Key Signal Selection, Keying Mode Selection (V-fade, FRONT PANEL CD-DSK-HD-PN interfaces with CD-DSK-HD through CAT-5 cable. Remote control is available via RS-422 control. BACK PANEL 1. By-Pass Select Button 2. KEY1 Source Select Button 3. KEY2 Source Select Button 4. KEY3 Source Select Button 5. Cut Button 6. Cut-Fade Button 7. V-Fade Button 8. Fade-Cut Button 9. Rate Select Button 10. Execution Button 11. Double RJ-45 Connectors One acts as RS-422 control interface to connect with CD-DSK, hotswappable not supported; the other one is used for control panel expansion, loop-thru supported. ORDERING INFORMATION CD-DSK-HD CD-DSK-HD-PN HD / SD-SDI tri-channel downstream keyer CD-DSK-HD control panel www.ogdentec.com Technical Support: support@ogdentec.com 139
CD-DAP SD-SDI Digital Audio Processor triggering. Automatic cable equalization is up to 1000 ft (about 300 m). CD-DAP can be controlled through the dedicated control panel. Monitoring of embedded audio and PPM/VU in PGM IN or PST IN channel is available. CD-DAP is a modular digital audio processor designed to work in a CEDAR frame. It analyzes and processes power characteristics of embedded audio signal in SD-SDI; therefore, it offers dynamic processing for the audio signal, including compression, limit, expansion and gain trimming. CD-DAP provides two SD-SDI inputs with embedded audio (PST IN, PGM IN) and two SD-SDI outputs. It performs de-embedding, characteristic analysis, dynamic control and embedding of the main program input channel (PGM IN). It supports de-embedding and level adjustment of the preview input channel (PST IN). PGM IN channel supports by-pass protection, which ensures the program to be output without any interruption even when power is off. The bypass protection can be activated through the control panel or GPI CD-DAP is widely used in the broadcasting industry for dynamic control of embedded audio in SD-SDI signals. Analyzes and processes power characteristic of audio signal Dynamic processing of audio signal, including compression, limit, expansion and gain trimming Automatic input cable equalizing up to 1000 ft (about 300 m) By-pass protection Selects embedded audio (16 channels) with control panel Supports GPI input BACK MODULE BLOCK DIAGRAM Electrical Power Consumption 5 W Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Digital Video Input Signal Format SMPTE 259M-C, 270 Mbps, 625/625 component Signal Standards SMPTE 272M AUX Data Embedding Standard Connector BNC ( 2) Impedance 75 Ω Return Loss 18 db @ 270 MHz Cable EQ <1000 ft (about 300 m) Belden 1694A cable or equivalent Digital Video Output Signal Format SMPTE 259M-C, 270 Mbps, 525/625 component Connector BNC ( 2) Impedance 75 Ω Return Loss 18 db @ 270 MHz Amplitude 800 mvp-p ±10% Rise/Fall Time 400 ~ 1500 ps, 20%~80% of amplitude Overshoot <10% of amplitude Jitter <0.12UI Digital Audio Output Signal Format AES3 Connector RJ-45 Impedance 110 Ω Level 5 Vp-p ±10% Performance Gain Adjustment Range -20 db ~ +20 db Compress Ratio 1:1 ~ :1 Compress Threshold VU: -44 dbfs ~ -4dBFS Expansion Threshold -60 dbfs ~ -20 dbfs Attack Time 0.1 ms ~ 500 ms, Compression & Expansion Release Time 20 ms ~ 5 s, Compression & Expansion Noise Threshold -70 dbfs ~ -44 dbfs 140 Ogden Technology Corporation An Expert in Signal Management
CD-DAP-HD HD / SD-SDI Digital Audio Processor cable equalization is up to 1000 ft (about 300 m). CD-DAP-HD can be controlled through the dedicated control panel. Monitoring of embedded audio and PPM/VU on PGM IN or PST IN channel is available. CD-DAP-HD is widely used in the broadcasting industry for dynamic control of embedded audio in HD/SD-SDI signals. CD-DAP-HD is a modular digital audio processor designed to work in a CEDAR frame. It analyzes and processes power and loudness characteristic for embedded audio signal in HD/SD-SDI; therefore, it offers dynamic processing of audio signal, including audio compression, limit, expansion and gain trimming. Additionally, the compression or expansion threshold can be selected according to audio UV or loudness. CD-DAP-HD provides two digital signal inputs with embedded audio (PST IN, PGM IN) and two digital signal outputs (PGM OUT1, PGM OUT2). It performs de-embedding, characteristic analysis, dynamic control and embedding of the main program input channel (PGM IN). It supports de-embedding and level adjustment of the preview input channel (PST IN). PGM IN channel supports by-pass protection, which ensures the program to be output without any interruption even when power is off. The by-pass protection can be activated through the control panel or GPI triggering. Automatic Analyzes and processes power and loudness characteristics of audio signal Dynamic processing of audio signal, including compression, limit, expansion and gain trimming Selectable compression or expansion threshold according to audio VU or loudness Automatic loudness control Automatic cable equalizing up to 1000 ft (about 300 m) for SD; and 500 ft (about 160 m) for HD By-pass protection Selects embedded audio (8 channels) with control panel Supports GPI input BACK MODULE BLOCK DIAGRAM Electrical Power Consumption 5 W Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Digital Video Input Signal Format SMPTE 259M SD-SDI, SMPTE 292M HD-SDI Signal Standards SMPTE 272M and SMPTE 299M Connector BNC ( 2) Impedance 75 Ω Return Loss >18 db @ 270 MHz, SD >15 db @ 1.485 GHz, HD Digital Video Output Signal Format SMPTE 259M, SMPTE 292M Connector BNC ( 2) Impedance 75 Ω Return Loss >12 db @ 5 MHz ~ 1.5 GHz Amplitude 800 mvp-p ±10% Rise/Fall Time 400 ~ 1500 ps, 20% ~ 80% of amplitude Overshoot <10% of amplitude Jitter <0.12 UI, SD <0.2 UI, HD Digital Audio Output Signal Format AES3 Connector RJ-45 Impedance 110 Ω Level 5 Vp-p ±10% Performance Gain Adjustment Range -20 db ~ +20 db Compress Ratio 1:1 ~ :1 Compress Threshold VU: -44 dbfs ~ -4 dbfs Loudness: -54 dbfs ~ -14 dbfs Expansion Threshold -60 dbfs ~ -20 dbfs, Loudness & VU Attack Time 0.1 ms ~ 500 ms, Compression & Expansion Release Time 20 ms ~ 5 s, Compression & Expansion Noise Threshold -70 dbfs ~ -44 dbfs www.ogdentec.com Technical Support: support@ogdentec.com 141
CD-DAP-PN CD-DAP / CD-DAP-HD Control Panel GPI trigger, quick audio processing Intuitive LCD menu display CD-DAP-PN is a remote control panel for CD-DAP / CD-DAP-HD. The parameters of CD-DAP can be set via the control panel. The audio embedded in PGM IN / PST IN and the value of PPM / VU can be monitored. BLOCK DIAGRAM CD-DAP-PN connects to CD-DAP via a single CAT-5 cable for remote control. Controls the status and parameters of CD-DAP or CD-DAP-HD Monitors embedded audio of CD-DAP or CD-DAP-HD Two 30-segment LED audio meters, displays PPM / VU value (indication range: -66 dbfs ~ 0 dbfs) Recalls preset status and sets user-defined status FRONT PANEL BACK PANEL 1. Loudspeaker 2. LCD display 3. Audio monitor select switch 4. 30-segment audio meter 5. Presetting status select indicators 6. By-pass switch 7. Monitoring volume control 8. Presetting status recall select button 9. Adjusting function select button 10. Power supply input connector 11. GPIO connector 12. Remote interface 13. Analog audio output connectors Mechanical Width 19 in. (483 mm) Height 1RU (44 mm) Depth 5.6 in. (141 mm) Electrical Power 10 W Power Supply 80 ~ 260 V AC Power Consumption 50 W Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Digital Audio Input Signal Format AES3 Connector RJ-45 ( 2), loop-thru Impedance 110 Ω Level 2 ~ 7 Vp-p Control Interfaces RS-485 RJ-45 ( 2), loop-thru GPI/O DB-25F ( 1) Speaker Output Impedance 8 Ω Frequency Range 20 Hz ~ 20 khz ORDERING INFORMATION CD-DAP CD-DAP-HD CD-DAP-PN SD-SDI digital audio processor HD / SD-SDI digital audio processor CD-DAP / CD-DAP-HD control panel 142 Ogden Technology Corporation An Expert in Signal Management
CD-ECO SD-SDI 2 1 Auto-Sync Emergency Changeover CD-ECO supports GPI triggering and dedicated control panel. CD-ECO is housed in a 1RU or 2RU CEDAR frame. It supports CEDAR-based network monitoring. Its parameters can be configured and adjusted through CEDAR router and the supporting control software which is also used to monitor the operating status and signal status of the module. CD-ECO is a modular and 2 1 auto-sync emergency changeover specially designed to work in a CEDAR frame. It performs synchronization according to the external reference signal or the main signal. The main input SD-SDI signal and the backup input SD-SDI signal are automatically synchronous for seamless and clean switching. CD-ECO provides two SD-SDI inputs (MAIN, BACK-UP) and two outputs (SDI, CVBS/SDI). The SDI output channel supports bypass protection, which ensures the program can be output without interruption; and the SDI/CVBS output channel can be configured for either SD-SDI output or CVBS output as needed. CD-ECO detects the presence of SD-SDI signal and the embedded audio on a real-time basis. It identifies the absent signal according to the predetermined conditions. In case of loss, CD-ECO will route the corresponding valid signal to the output channel under automation; while send alarm to the control panel to alert the operator s for manual switching. BLOCK DIAGRAM Dual built-in frame synchronizer, auto-sync and seamless switching available Detects embedded audio presence Selectable duration for judging audio loss, including 20 s, 30 s, 40 s, 50 s and 60 s Supports analog video output monitoring Supports by-pass protection for main input channel Optional operating modes: Auto and Manual Supports GPI triggering Supports remote control panel Hot-swappable Supports PD-based network monitoring BACK MODULE Electrical Power Consumption 8 W Environmental Operating Temperature 32 ~ 104 F (0 ~ 40 C) Relative Humidity 10% ~ 90% Input Signal Format SMPTE 259M-C, 270 Mbps, 525/625 component Connector BNC ( 2) Impedance 75 Ω Return Loss 18 db @ 270 MHz Cable EQ <1000 ft (about 300 m) Belden 1694A cable or equivalent Output Signal Format SMPTE 259M-C, 270 Mbps, 525/625 component Connector BNC ( 1) Impedance 75 Ω Return Loss 18 db @ 270 MHz Amplitude 800 mvp-p ±10% Jitter <0.12 UI Rise/Fall Time 400 ~ 1500 ps, 20% ~ 80% of amplitude Overshoot <10% of amplitude Analog Monitoring Output Signal Format CVBS System NTSC, PAL Quantization 8 bits Connector BNC ( 1) Impedance 75 Ω Amplitude 1.0 Vp-p ±3% Chr/Lum Delay Diff <5 ns S/N Ratio >70 db @ 6 MHz www.ogdentec.com Technical Support: support@ogdentec.com 143