Operating Instructions Home Theater Audio System

Operating Instructions Home Theater Audio System Model No. SC-HTB170 Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. Included Installation Instructions The installation work should be done by a qualified installation specialist. ( 10 to 15) Before commencing work, carefully read these installation instructions and the operating instructions to ensure that installation is performed correctly. (Please keep these instructions. You may need them when maintaining or moving this unit.) Model number suffix EB denotes UK model. EG EB GN -2B

Safety precautions WARNING Unit To reduce the risk of fire, electric shock or product damage, jdo not expose this unit to rain, moisture, dripping or splashing. jdo not place objects filled with liquids, such as vases, on this unit. juse only the recommended accessories. jdo not remove covers. jdo not repair this unit by yourself. Refer servicing to qualified service personnel. AC mains lead To reduce the risk of fire, electric shock or product damage, jensure that the power supply voltage corresponds to the voltage printed on this unit. jinsert the mains plug fully into the socket outlet. jdo not pull, bend, or place heavy items on the lead. jdo not handle the plug with wet hands. jhold onto the mains plug body when disconnecting the plug. jdo not use a damaged mains plug or socket outlet. The mains plug is the disconnecting device. Install this unit so that the mains plug can be unplugged from the socket outlet immediately. Button-type battery (Lithium battery) Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 60 o C or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed call your doctor. CAUTION Unit Do not place sources of naked flames, such as lighted candles, on this unit. This unit may receive radio interference caused by mobile telephones during use. If such interference occurs, please increase separation between this unit and the mobile telephone. This unit is intended for use in moderate climates. Product Identification Marking is located on the bottom of the unit. Placement Place this unit on an even surface. To reduce the risk of fire, electric shock or product damage, jdo not install or place this unit in a bookcase, built-in cabinet or in another confined space. Ensure this unit is well ventilated. jdo not obstruct this unit s ventilation openings with newspapers, tablecloths, curtains, and similar items. jdo not expose this unit to direct sunlight, high temperatures, high humidity, and excessive vibration. Button-type battery (Lithium battery) Danger of explosion if battery is incorrectly replaced. Replace only with the type recommended by the manufacturer. Insert with poles aligned. Mishandling of batteries can cause electrolyte leakage and may cause a fire. jremove the battery if you do not intend to use the remote control for a long period of time. Store in a cool, dark place. jdo not heat or expose to flame. jdo not leave the battery(ies) in a car exposed to direct sunlight for a long period of time with doors and windows closed. When disposing the batteries, please contact your local authorities or dealer and ask for the correct method of disposal. 2

Caution for AC Mains Lead (For the AC mains plug of three pins) For your safety, please read the following text carefully. This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5-ampere and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local dealer. Before use Remove the connector cover. How to replace the fuse The location of the fuse differ according to the type of AC mains plug (figures A and B). Confirm the AC mains plug fitted and follow the instructions below. Illustrations may differ from actual AC mains plug. 1. Open the fuse cover with a screwdriver. Figure A 2. Replace the fuse and close or attach the fuse cover. Figure A Fuse (5 ampere) Figure B Figure B Fuse cover Fuse (5 ampere) About Bluetooth Panasonic bears no responsibility for data and/or information that is compromised during a wireless transmission. Frequency band used This system uses the 2.4 GHz frequency band. Certification of this device This system conforms to frequency restrictions and has received certification based on frequency laws. Thus, a wireless permit is not necessary. The action below are punishable by law in some countries: jtaking apart or modifying the unit. jremoving specification indications. Restrictions of use Wireless transmission and/or usage with all Bluetooth equipped devices is not guaranteed. All devices must conform to standards set by Bluetooth SIG, Inc. Depending on the specifications and settings of a device, it can fail to connect or some operations can be different. This system supports Bluetooth security features. But depending on the operating environment and/or settings, this security is possibly not sufficient. Transmit data wirelessly to this system with caution. This system cannot transmit data to a Bluetooth device. Range of use Use this device at a maximum range of 10 m. The range can decrease depending on the environment, obstacles or interference. Interference from other devices This system may not function properly and troubles such as noise and sound jumps may arise due to radio wave interference if the main unit is located too close to other Bluetooth devices or the devices that use the 2.4 GHz band. This system may not function properly if radio waves from a nearby broadcasting station, etc. are too strong. Intended usage This system is for normal, general use only. Do not use this system near equipment or in an environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc.). 3 Precautions

Table of contents Safety precautions... 2 Caution for AC Mains Lead... 3 About Bluetooth... 3 Before use Supplied items... 5 This system (SC-HTB170)... 5 Accessories... 5 Control reference guide... 6 This system (Front)... 6 This system (Rear)... 7 Remote control... 8 Getting started Step 1 Selecting the placement method... 9 The main unit... 9 Wireless interference... 10 Step 2 Placement... 11 When placing the main unit in a rack or on a table... 11 When attaching the main unit to a wall... 13 Step 3 Connections... 16 Connection with the TV... 16 Connection from an HDMI compatible device... 17 Using the IR Blaster... 18 AC mains lead connection... 19 Bluetooth connection... 19 Operations Using this system... 20 3D sound... 21 Sound modes... 21 Linked operations with the TV (VIERA Link HDAVI Control TM )... 22 Advanced operations... 23 Reference Troubleshooting... 26 Indicator illumination... 29 Specifications... 30 Unit care... 31 Licenses... 31 Limited Warranty (ONLY FOR AUSTRALIA)... 35 4

Before use The illustrations shown may differ from your unit. These operation instructions are applicable to model SC-HTB170 for variety of regions. Unless otherwise indicated, illustrations in these operating instructions are of the model for the United Kingdom and Ireland. Operations in this operating instructions are described mainly with the remote control, but you can perform the operations on the main unit if the controls are the same. Supplied items This system (SC-HTB170) 1 Main unit (speaker) (SC-HTB170) Accessories Check the supplied accessories before using this system. 1 Remote control (with a battery) (N2QAYC000083) 1 AC mains leads For the United Kingdom and Ireland (K2CT2YY00097) 2 Safety holders (RXA0260) 1 IR Blaster (K2ZZ02C00007) For continental Europe (K2CQ2YY00119) 2 Wall mount brackets (RMQX1082-K) For Australia and New Zealand (K2CJ2YY00093) 2 Basic stands (RYQ1165-K) 230 o stands 280 o stands 4 Screws (RYQ1166-K) (with washerk2: XYN5+J14FJK) (RYQ1167-K) (without washerk2: XSN4+8FJK) Reference Operations Getting started Before use Precautions Product numbers are correct as of December 2012. These may be subject to change. The supplied AC mains lead is for use with this system only. Do not use it with other equipment. Also, do not use cords from other equipment with this system. 5

Control reference guide This system (Front) 4 5 6 1 2 3 1 Standby/on switch (Í/I) Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. 2 Adjust the volume of this system 3 Select the input source TV ----------------# BD/DVD ^-------- (--------------} 4 Speaker angle indicator ( 9) Angle 1: 0 o tilt Speaker angle indicator lights green Angle 2: Tilted at 30 o Speaker angle indicator lights amber Angle 3: Tilted at 80 o /90 o Speaker angle indicator lights red 5 Input selector indicators* 1 A Bluetooth indicator Lights blue when the Bluetooth device is the audio source B TV indicator Lights green when the TV is the audio source C BD/DVD indicator Lights amber when the device connected to the BD/DVD terminal is the audio source 7 6 Sound mode indicators* 1 D STANDARD indicator Lights when STANDARD is the current sound mode E STADIUM indicator* 2 Lights when STADIUM is the current sound mode F MUSIC indicator* 2 Lights when MUSIC is the current sound mode G CINEMA indicator Lights when CINEMA is the current sound mode H NEWS indicator Lights when NEWS is the current sound mode I STEREO indicator Lights when STEREO is the current sound mode 7 Remote control signal sensor ( 8) 6

This system (Rear) 6 1 AC IN terminal ( 19) 2 Ir SYSTEM terminal ( 18) 3 OPTICAL DIGITAL AUDIO IN (TV) terminal ( 16) 4 HDMI OUT terminal (ARC compatible) ( 16) 5 HDMI IN terminal ( 17) 6 USB port (for service use only) *1 The indicators will also blink in various conditions. ( 29) *2 The indicator blinks for 5 sec when the main unit detects an audio format. To manually verify the current audio format and the corresponding indicators, refer to page 23 (Audio format indicator). Before use 7

Remote control Before using for the first time Remove the insulation sheet A. 1 3 2 4 6 7 INPUT SELECTOR SOUND 5 8 To replace a button-type battery Battery type: CR2025 (Lithium battery) 1 Turn the main unit on or off ( 20) 2 Adjust the dialog effect level ( 20) 3 Adjust the output level of the subwoofer (bass sound) ( 20) 4 Adjust the volume of this system ( 20) 5 Mute the sound ( 20) 6 Select the input source ( 20) TV --------------------# BD/DVD ^------------ (---------} 7 Select the Bluetooth device as the source ( 20) 8 Select the sound mode ( 21) STANDARD -----# STADIUM ----# MUSIC ^- STEREO ( NEWS ( CINEMA (} Set the button-type battery with its (i) mark facing upward. Keep the button-type battery out of reach of children to prevent swallowing. Remote control operation range The remote control signal sensor is located on the main unit. Use the remote control within the correct operation range. B Remote control signal sensor Operation range Distance: Within approx. 7 m directly in front Angle: Approx. 30 o left and right 8

Getting started Step 1 Selecting the placement method Choose a placement method that suits you best. The main unit When placing the main unit in a rack or on a table Angle 1: 0 o tilt Speaker angle indicator lights green. Page 11 [A] Raised by using the basic stands Angle 2: Tilted at 30 o Speaker angle indicator lights amber. [B] Tilted by using 30 o stands Page 11 Getting started Before use Angle 3: Tilted at 80 o Speaker angle indicator lights red. [C] Tilted by using 80 o stands Page 11 When attaching the main unit to a wall Angle 3: Tilted at 90 o Speaker angle indicator lights red. Page 13 9

Safety Precautions Professional installation is required. The installation should never be done by any other than a qualified installation specialist. PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING. Be sure to install the main unit as indicated within this operating Instructions. Attach using techniques suited to the structure and materials of the installation location. Caution This system is to be used only as indicated in these instructions. Failure to do so may lead to damage to the amplifier and/or the speaker, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance. Do not attempt to attach the main unit to a wall using methods other than those described in this manual. Keep the safety holders, screws and wall mount brackets out of reach of children to prevent swallowing. The safety holder is to minimize the possibility of damage and harm, but it does not completely guarantee this effect. Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it. To prevent damage or scratches, lay down a soft cloth and perform the assembly on it. When placing the main unit in front of the TV The main unit may block or interfere with the TV s various sensors (C.A.T.S. (Contrast Automatic Tracking System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D compatible TV. If interference occurs, use a lower angle stand or place the main unit without a stand or move the main unit further away from the TV. If the TV still does not function correctly, try using it in a rack or in the wall mount position. If the TV s remote control sensor is blocked by the main unit Try using the TV s remote control from a different angle. If the problem persists, you can use the supplied IR Blaster to relay the signal to the TV. ( 18) Do not use the IR Blaster if the TV s remote control sensor is not blocked by the main unit. Wireless interference To avoid interference, maintain the following distances between the main unit and other electronic devices that use the same radio frequency (2.4 GHz band). B A B The main unit Wireless router, cordless phone and other electronic devices: approx. 2 m A Do not use the main unit in a metal cabinet. If irregular colouring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit further away from the TV. Keep magnetised items away. Magnetised cards, watches, etc., can be damaged if placed too close to the main unit. 10

Step 2 Placement Supplied accessories Additionally required accessories (commercially available) Fall prevention cord... k 2 Screw eyes (to attach the fall prevention cord)... k 2 Use commercially available screws that are capable of supporting over 33 kg. Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm). Attach the cord to the main unit. When placing the main unit in a rack or on a table Place the main unit on a flat and horizontal surface. 2 Basic stands 2 30 o stands 2 80 o stands 2 Screws with washer Getting started Precautions A Cord* * If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about 5 mm apart from the tip, at an angle of 45 o (as illustrated above). 11

Attach the stands if necessary. If not, proceed to step 3. [A]: With basic stands [B]: With 30 o stands [C]: With 80 o stands e.g., With basic stands A Screw (supplied) Tighten securely. Place the main unit in the desired position and attach each cord onto the rack or table. Make sure that the slack of the cord is minimal. B Screw eye Attach at a position capable of supporting over 33 kg. Depending on the placement of the main unit, the screwing position of the screw eye may differ. 12

When attaching the main unit to a wall Place the main unit on a flat and vertical surface. This unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg. The screws and other items are not supplied as the type and size will vary with each installation. Refer to step 2 for details about the required screws. Be sure to attach the fall prevention cord as a secondary safety measure. Supplied accessories 2 Safety holders 2 Wall mount brackets 2 Screws without washer Additionally required accessories (commercially available) Screws for wall mounting... k 4 Fall prevention cord... k 2 Screw eyes (to attach the fall prevention cord)... k 2 Use a cord that is capable of supporting over 33 kg (with a diameter of about 1.5 mm). Locate the screwing positions on the wall. Use the measurements indicated below to identify the screwing positions on the wall. Leave at least 100 mm of space above of the main unit to allow enough space for fitting the main unit. Position the main unit with at least 50 mm of free space to its right. If not, it may not be possible to access the buttons. Be sure to use a level to ensure that both screwing positions are horizontal to each other. A B C D E Getting started Precautions F J H I G J A 950 mm B 153 mm C 322 mm D 310 mm E 165 mm F 105 mm G 74 mm H 31 mm I 12.5 mm J Wall mount bracket (supplied) 13

Attach the wall mount brackets to the wall. A B Wall mount bracket (supplied) Screws C D E F G At least 30 mm 4.0 mm 7.5 mm to 9.4 mm Wall Wall mount bracket (supplied) Complete all the necessary connections to the main unit. ( 16 to 19) Connect the AC mains lead cord to the main unit, but do not connect it to the household mains socket until the installation is completed. Attach the cord to the main unit. H Cord* * If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about 5 mm apart from the tip, at an angle of 45 o (as illustrated above). 14

Attach the main unit to the wall mount brackets. A Wall mount bracket (supplied) B Gently move the main unit down onto the wall mount bracket. Screw the safety holder onto the wall mount brackets. Screw tightening torque: 80 N0cm to 120 N0cm. The safety holders are designed to prevent the main unit from falling off the wall mount bracket. Getting started Precautions C D E Screw without washer (supplied) Safety holder (supplied) Wall mount bracket (supplied) Secure the cord to the wall. F Wall G About 15 o Tilt about 15 o from the wall and tighten the screw. Make sure that the slack of the cord is minimal. H I Screw eye Cord 15

Step 3 Connections Turn off all equipment before connection and read the appropriate operating instructions. Do not connect the AC mains lead until all other connections are completed. HDMI The HDMI connection supports VIERA Link HDAVI Control ( 22) when used with a compatible Panasonic TV. Use the ARC compatible High Speed HDMI Cables. Non-HDMI-compliant cables cannot be utilised. It is recommended that you use Panasonic s HDMI cable. Connection with the TV Verify if the TV s HDMI terminal is labelled HDMI (ARC). Connection differs depending on the label printed next to the HDMI terminal. Labelled HDMI (ARC) : Connection [A] Not Labelled HDMI (ARC) : Connection [B] What is ARC? ARC is an abbreviation of Audio Return Channel, also known as HDMI ARC. It refers to one of the HDMI functions. When you connect the main unit to the terminal labelled HDMI (ARC) on the TV, the optical digital audio cable that is usually required in order to listen to sound from a TV is no longer required, and TV pictures and sound can be enjoyed with a single HDMI cable. Make the connection. [A] Labelled HDMI (ARC) TV HDMI IN (ARC) Be sure to connect to the TV s ARC compatible terminal. (Refer to the operating instructions for the TV.) A AV OUT TV(ARC) A HDMI cable [B] Not labelled HDMI (ARC) B OPTICAL DIGITAL AUDIO IN TV OPTICAL OUT HDMI IN A TV AV OUT TV(ARC) A HDMI cable B Optical digital audio cable When you use the optical digital audio cable, insert the tip correctly into the terminal. 16

Connection from an HDMI compatible device You can direct the audio signal from the connected Blu-ray Disc player, DVD player, Set Top Box, etc. to this system. Preparation Connect the main unit to the TV. ( 16) e.g., Blu-ray Disc player HDMI OUT A AV IN BD/DVD A HDMI cable HDMI standby pass-through Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the HDMI IN terminal will be sent to the TV connected to the HDMI OUT terminal (the sound will not be output from this system). 3D compatibility Compatible with FULL HD 3D TV and Blu-ray Disc player. The main unit can pass-through the 3D video signal from a 3D compatible Blu-ray Disc player to a FULL HD 3D TV. Refer to the operating instructions of the connected HDMI compatible device for the necessary setting, to output the video and audio signals. Getting started 17

Using the IR Blaster With the IR Blaster connection, it is possible to send the IR signal received by this system s remote control signal sensor to the TV s sensor. Use the TV s remote control within the operation range of this system s remote control signal sensor. For the operation range, refer to page 8. Connect the jack plug to the main unit s Ir SYSTEM terminal. A Infrared emitter Ir SYSTEM Place the infrared emitter in sight of the TV s remote control signal sensor. For the location of the TV s remote control signal sensor, refer to the operating instructions for the TV. Aim the TV s remote control at this system s remote control sensor and operate the TV. For the location of this system s remote control signal sensor, refer to page 6. Make sure to clean the surface, where the adhesive tape is to be attached. If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have confirmed the TV is operating correctly, secure it by attaching the adhesive tape. The supplied IR Blaster is only compatible with Panasonic TVs. Keep the adhesive tape out of reach of children to prevent swallowing. Placement example On the rear of the main unit: TV remote control signal sensor Adhesive tape (supplied) 18

AC mains lead connection Connect only after all other connections are completed. A B To a household mains socket AC mains lead (supplied) AC IN This system consumes a small amount of AC power ( 30) even when it is turned off. In the interest of power conservation, if you will not be using this system for a long time, unplug it from the household mains socket. For customers in United Kingdom and Ireland BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 3 BEFORE CONNECTION. Saving energy The main unit is designed to conserve its power consumption and save energy. The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx. 2 hours. Refer to page 24, Auto standby function to turn this function off. Bluetooth connection By using the Bluetooth connection, you can listen to the sound from the Bluetooth audio device from this system wirelessly. Preparation Turn on the Bluetooth feature of the device and place the device near the main unit. Bluetooth pairing Press [ ] to select. If the indicator flashes quickly, go to step 3. Press and hold [ ] until the indicator flashes quickly. If the indicator flashes slowly, repeat step 2. Select SC-HTB170 from the Bluetooth device s Bluetooth menu. If prompted for the passkey on the Bluetooth device, enter 0000. Once the Bluetooth device is connected, the indicator stops flashing and lights up. You can register up to 8 devices with this system. If a 9th device is paired, the device that has not been used for the longest time will be replaced. Press [ ] to select. If the indicator lights, a Bluetooth device is already connected with this system. Disconnect it. ( below) Select SC-HTB170 from the Bluetooth device s Bluetooth menu. Disconnecting a Bluetooth device Press and hold [ ] until the indicator flashes slowly. Connecting a Bluetooth device When is selected as the source, this system will automatically try and connect to the last connected Bluetooth device. The Bluetooth device will be disconnected if a different audio source (e.g. TV ) is selected. Refer to the operating instructions of the Bluetooth device for further instruction on how to connect a Bluetooth device. This system can only be connected to one device at a time. To change the sound quality, refer to Bluetooth communication mode on page 23. 19 Getting started

Operations Using this system Preparation Turn on the TV and/or connected device. DIALOG LEVEL INPUT SELECTOR LINK MODE ----PAIRING Press [Í] to turn on the main unit. Select the source. SOUND Press To select [INPUT TV --------------# BD/DVD SELECTOR] ^--------- (---------} [ ] (Bluetooth ) This remote control cannot be used to control the operations of the connected devices. When is selected as the source On the Bluetooth device: Select this system as the output source of the connected Bluetooth device and start the playback. When BD/DVD is selected as the source On the TV and the connected device: Select the TV s input for this system and start the playback on the connected device. Adjust the volume and sound effect level. To adjust the volume of this system Press [i VOL j]. Volume range: 0 to 100* To adjust the dialog effect level This setting will change the level of the Clearmode dialog effect. ( 21) 1 Press [i DIALOG LEVEL j] to display the current level. 2 While the level is displayed: Press [i DIALOG LEVEL j] to adjust the level. Indication Effect level 4 Highest To adjust the subwoofer level 1 Press [i SUBWOOFER j] to display the current level. 2 While the level is displayed: Press [i SUBWOOFER j] to adjust the level. The level indication pattern is the same as dialog effect level. To mute the sound Press [MUTE]. While muting, the sound mode indicators blink simultaneously. To cancel, press the button again or adjust the volume. Muting is cancelled if the main unit is turned off. 3 2 1 Lowest If this system does not operate as expected or sound is unusual, returning the settings to the factory preset may solve the problem. ( 26) * The sound mode indicators blink from left to right (i) or from right to left (s) while adjusting. The indicators will not blink when it has reached the maximum or minimum. If there is sound coming out of the TV s speakers, reduce the volume of the TV to its minimum. If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically lower the volume to the middle (50) when the main unit is turned on (Volume limitation). To turn this function off, refer to page 25. 20

3D sound This system provides a feeling that the sound and the image are as one. To change the applied effect, refer to Sound modes. ( right) e.g., Image of 3D sound field Sound modes By changing the sound mode, it is possible to enjoy the sound that is suitable to the TV program or image from the connected device. To select the sound mode Press [SOUND]. STANDARD ---# STADIUM ---# MUSIC ^- STEREO ( NEWS ( CINEMA (} The indicator for the selected sound mode lights. e.g., STEREO Dolby Virtual Speaker 3D surround effect Clear-mode dialog 3D sound With this effect you can enjoy a surround sound effect similar to 5.1ch. Adding to the Dolby Virtual Speaker effect, Panasonic has applied its own sound field controlling technology to expand the sound field forwards, backwards, upwards, and downwards, providing a sound with depth and force that better matches 3D images. Sports commentary and dialogs from TV dramas are heard as if the sound is coming from the TV, giving the feeling that the sound and the image are one. Also, the dialog will stand out from the other sounds during normal volume playback and when the volume is lowered for night time viewing. To turn off Dolby Virtual Speaker and the 3D surround effects, select STEREO as the sound mode. ( right) To turn off the 3D surround and the Clear-mode dialog effects, refer to Using the Dolby Virtual Speaker effect. ( 24) Sound mode STANDARD Produces a sound best suited for dramas and comedy shows. STADIUM Produces a highly realistic sound for live broadcasts of sports. MUSIC Re-creates the sound of musical instruments and songs with an expansive sound. CINEMA Produces a powerful, threedimensional sound unique to movies. NEWS Enhances the voices of news and sports commentaries for clearer hearing. STEREO You can play any source in (Factory preset) stereo. Dolby Virtual Speaker and 3D surround effects are turned off. The setting is maintained until it is changed again. Operations 21

Linked operations with the TV (VIERA Link HDAVI Control TM ) What is VIERA Link HDAVI Control? VIERA Link HDAVI Control is a convenient function that offers linked operations of this system, and a Panasonic TV (VIERA) under HDAVI Control. You can use this function by connecting the equipment with an HDMI cable. See the operating instructions for connected equipment for operational details. Preparation 1 Confirm that the HDMI connection has been made. ( 16, 17) 2 Set the HDAVI Control operations on the connected equipment (e.g., TV). 3 For the optimal HDAVI Control operations change the following settings on the connected TV* 1. Set the default speaker settings to this system.* 2 Set the speaker selection settings to this system. 4 Turn on all HDAVI Control compatible equipment and select the TV s input for this system so that the HDAVI Control function works properly. 5 If a device is connected to the HDMI IN terminal, start play to check that the picture is displayed on the TV correctly. When the connection or settings are changed, repeat this procedure. *1 The availability and function of the settings may vary depending on the TV. Refer to the operating instructions for the TV for details. *2 If the TV has a default speaker setting within the VIERA Link setting items, choosing this system as the default speaker will automatically change the speaker selection to this system. VIERA Link HDAVI Control, based on the control functions provided by HDMI which is an industry standard known as HDMI CEC (Consumer Electronics Control), is a unique function that we have developed and added. As such, its operation with other manufacturers equipment that supports HDMI CEC cannot be guaranteed. This unit supports HDAVI Control 5 function. HDAVI Control 5 is the standard for Panasonic s HDAVI Control compatible equipment. This standard is compatible with Panasonic s conventional HDAVI equipment. Please refer to individual manuals for other manufacturers equipment supporting VIERA Link function. What you can do with VIERA Link HDAVI Control To make sure that the audio is output from this system, turn the main unit on by using the TV s remote control and selecting home cinema from the speaker menu of VIERA Link menu. The availability and function of the settings may vary depending on the TV. Refer to the operating instructions for the TV for details. Speaker control You can select whether audio output is from this system or the TV speakers by using the TV menu settings. Home cinema This system is active. When the main unit is in standby mode, changing the TV speakers to this system in the VIERA Link menu will automatically turn the main unit on. You can control the volume setting of this system using the volume or mute button on the TV remote control. If you turn off the main unit, TV speakers will be automatically activated. Audio will automatically be output from this system if the TV is compatible to VIERA Link HDAVI Control 4 or later. TV TV speakers are active. The volume of this system is set to its minimum. Automatic input switching When the following operations are performed, the main unit will automatically change the input to the corresponding source. jwhen play starts on an HDMI connected device.* 3 jwhen the TV input or the TV channel is changed. *3 If the speaker output setting on the TV is set to this system, the TV and the main unit turn on automatically (Power on link). Power off link When the TV is turned off, the main unit also turns off automatically. (This function does not work when Bluetooth is the source.) Automatic lip-sync function (for HDAVI Control 3 or later) Delay between audio and video is automatically adjusted by adding time-lag to the audio output, enabling you to enjoy smooth audio for the picture. The delay information is automatically set if the TV is compatible to VIERA Link HDAVI Control 3 or later and the VIERA Link is set to on. 22

23 ページ ２０１３年２月４日 Advanced operations Audio format indicator To display the current audio format. Press and hold [SOUND] for more than 4 sec. 月曜日 午前９時５分 Auto gain control With this function, you can prevent sudden loud sounds. The output will be reduced automatically when the input exceeds a certain level. Press and hold [INPUT SELECTOR] on the remote control for more than 4 sec. The current audio format is indicated for 5 sec. STADIUM indicator blinks: Dolby Digital is the audio format. STANDARD indicator blinks: Auto gain control is on. MUSIC indicator blinks: DTS is the audio format. STEREO indicator blinks: Auto gain control is off. (Factory preset) CINEMA indicator blinks: PCM is the audio format. Audio format is not indicated when source. is selected as the Changing the dual audio Change the dual audio from main to secondary. This setting will only work if the audio output setting on the connected TV or player, etc. is set to Bitstream and dual audio is available in the audio source. Press and hold [MUTE] for more than 4 sec. STANDARD indicator blinks (A): Main (Factory preset) STEREO indicator blinks (B): Secondary (SAP: Secondary Audio Program) When A and B both blink: Main and secondary While the setting is displayed, press [MUTE] to change the setting. The setting changes each time [MUTE] is pressed. The indicator for the selected setting blinks for 20 sec and then exits the setting mode. The setting is maintained until it is changed again. While the setting is displayed, press [INPUT SELECTOR] on the remote control to change the setting. The setting changes each time [INPUT SELECTOR] is pressed. The indicator for the selected setting blinks for 20 sec and then exits the setting mode. The setting is maintained until it is changed again. Bluetooth communication mode You can select different modes to suit the type of connections with emphasis on connectivity or high quality audio. Make sure that a Bluetooth device is already paired with this system. (> 19) Press [ ] to select. indicator will blink slowly. If the indicator lights, a Bluetooth device is already connected with this system. Disconnect it. (> 19) Press [ ] to display the current mode. STANDARD indicator blinks: MODE1 (Factory preset) Emphasis on connectivity STEREO indicator blinks: MODE2 Emphasis on audio quality While the mode is displayed, press [ ] to select the mode. The setting changes each time [ ] is pressed. The indicator for the selected setting blinks for 10 sec and then exits the setting mode. The setting is maintained until it is changed again. 23 Operations SC-HTB170EGEBGN_-B.book

Using the Dolby Virtual Speaker effect Depending on your preference, It is possible to turn off the 3D surround effect and the clearmode dialog effect. While pressing and holding [SOUND] on the remote control, press and hold [VOL i] on the main unit for more than 4 sec. STANDARD indicator blinks: 3D surround effect and clear-mode dialog effect is on. STEREO indicator blinks: 3D surround effect and clear-mode dialog effect is off. While the setting is displayed, press [SOUND] to change the setting. The setting changes each time [SOUND] is pressed. The indicator for the selected setting blinks for 20 sec and then exits the setting mode. This setting will be reset to on when the main unit is turned off. When off is selected, the dialog effect level cannot be adjusted. Dimmer mode You can turn off dimmer mode and keep the LED indicators bright. While pressing and holding [INPUT SELECTOR] on the remote control, press and hold [s VOL] on the main unit for more than 4 sec to turn off Dimmer mode. The indicator for the current condition will turn brighter. The setting is maintained until it is changed again. Default setting of this function is on. To turn on dimmer mode, repeat the operation above. After performing the operation, the indicator for the current condition will be dim. Auto standby function With this function turned on, this unit can be set to automatically switch to standby mode if there is no signal input and no operation is performed for 2 hours. While pressing and holding [DIALOG LEVEL j] on the remote control, press and hold [INPUT SELECTOR] on the main unit for more than 4 sec. The indicator for the current setting blinks for 20 sec. STANDARD indicator blinks: Auto standby function is on. STEREO indicator blinks: Auto standby function is off. While the indicator is blinking, press [DIALOG LEVEL j] to change the setting. The setting changes each time [DIALOG LEVEL j] is pressed. The setting is maintained until it is changed again. 24

Others Remote control code When other Panasonic devices respond to this system s remote control, change the remote control code on this system and the remote control. Preparation Turn off all other Panasonic products. Turn on the main unit. Change the remote control code to code 2: 1 Aim the remote control at the main unit s remote control sensor. 2 Press and hold [MUTE] and [ ] on the remote control for more than 4 sec. All the indicators will blink for 10 sec when the code of this system is changed. To turn off VIERA Link HDAVI Control When HDAVI Control compatible equipment does not work well with this system, for example, it is possible to turn off this function as follows: When VIERA Link is turned off, the ARC function is not available. Be sure to connect the optical digital audio cable. ( 16) 1 While pressing and holding [MUTE] on the remote control, press and hold [s VOL] on the main unit for more than 4 sec. 2 After the setting has changed, turn off all the connected devices and then turn them on again. All the indicators will blink once when VIERA Link HDAVI Control is turned off. The setting is maintained until it is changed again. If the main unit does not operate after changing the code, repeat steps 1 and 2. To change the remote control code to code 1, repeat the steps above, but replace [ ] with [INPUT SELECTOR]. To reduce the clear-mode dialog effect When the dialog does not sound natural while the volume is set low, it is possible to reduce the dialog enhancing effect as follows: While pressing and holding [SOUND] on the remote control, press and hold [s VOL] on the main unit for more than 4 sec. All the indicators will blink once when the clear-mode dialog effect is reduced. To reset the setting, return to the factory preset. ( 26) To turn off the volume limitation If a state of the lowered volume disturbs you every time the main unit turns on, for example, it is possible to turn off this function as follows: While pressing and holding [MUTE] on the remote control, press and hold [VOL i] on the main unit for more than 4 sec. All the indicators will blink once when the volume limitation is turned off. To reset the setting, return to the factory preset. ( 26) Operations Even if clear-mode dialog effect is reduced, dialog effect level is still adjustable. To reset the setting, return to the factory preset. ( 26) 25

Reference Troubleshooting Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the following guide do not solve the problem, consult your dealer for instructions. To return to the factory preset. While the main unit is on, press [Í/I] on the main unit for more than 4 sec. (All the indicators will blink twice when this system is reset.) If this system does not operate as expected, returning the settings to the factory preset may solve the problem. The remote control code will return to 1 when this system is returned to the factory preset. To change the remote control code, refer to page 25. General operation No power. Insert the AC mains lead securely. ( 19) After turning the main unit on, if the indicators blink and the main unit immediately turns off, unplug the AC mains lead and consult your dealer. The remote control does not work properly. The battery is depleted. Replace it with a new one. ( 8) It is possible that the insulation sheet has not been removed. Remove the insulation sheet. ( 8) It may be necessary to set the code of the remote control again after changing the battery of the remote control. ( 25) Use the remote control within the correct operation range. ( 8) The main unit is automatically switched to standby mode. The auto standby function is on. The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx. 2 hours. Refer to page 24 to turn this function off. The colour of the speaker angle indicator does not match the tilt of the main unit. Change the speaker angle settings manually so that the indicator colour matches the tilt. 1 Press and hold [INPUT SELECTOR] on the main unit for more than 4 sec. The speaker angle indicator blinks. 2 While the indicator is blinking, press [INPUT SELECTOR] on the main unit repeatedly to match the indicator color with the placement method. Refer to Step 1 Selecting the placement method ( 9) for the relation between colour and tilt. The main unit is turned off when the TV s speakers are selected in the speaker control. This is a normal feature when using VIERA Link (HDAVI Control 4 or later). Please read the operating instructions for the TV for details about its power save feature. ( 22) The TV indicator blinks. Remove the AC mains lead and consult your dealer. If there are any other indicators blinking, be sure to inform your dealer about the blinking indicators. 26

HDMI Bluetooth This system does not operate correctly. If the HDMI cable is connected to the wrong terminal (HDMI IN or HDMI OUT), this system will not operate correctly. Turn the main unit off, disconnect the AC mains lead and reconnect the HDMI cable(s). ( 16, 17) VIERA Link related operations no longer function properly. Check the VIERA Link setting on the connected devices. Have you turned the VIERA Link settings off? ( 25) When the HDMI connections are changed, after a power failure or after the AC mains lead has been removed, VIERA Link operations may not function properly. jturn on all the devices that are connected to the TV with an HDMI cable and then turn the TV on. jturn off the VIERA Link settings of the TV and turn it on again. For details refer to the operating instructions for the TV. jwhile the main unit and the TV are connected with the HDMI cable, turn on the TV and then remove the main unit s AC mains lead and reconnect it again. The first few seconds of audio cannot be heard when using the HDMI connection. This may occur during DVD-Video chapter playback. Change the digital audio output setting on the connected device from Bitstream to PCM. Pairing cannot be done. Check the Bluetooth device condition. The device cannot be connected. The pairing of the device was unsuccessful or the registration has been replaced. Try pairing the device again. ( 19) This system might be connected to a different device. Disconnect the other device and try pairing the device again. The device is connected but audio cannot be heard through this system. For some built-in Bluetooth devices, you have to set the audio output to SC-HTB170 manually. Read the operating instructions for the device for details. The sound is interrupted. The device is out of the 10 m communication range. Bring the Bluetooth device closer to the main unit. Remove any obstacle between the main unit and the device. Other devices that use the 2.4 GHz frequency band (wireless router, microwaves, cordless phones, etc.) are interfering. Bring the Bluetooth device closer to the main unit and distance it from the other devices. Select MODE1 for stable communication. ( 23) When operating an HDMI compatible device of a different brand, the main unit reacts in an unwanted manner. HDAVI Control commands may use a different signal depending on the brand of the device. In this case, turn VIERA Link off. ( 25) Reference 27

Sound No sound (or image). Turn muting off. ( 20) Check the connections to the other devices. ( 16, 17) Make sure that the received audio signal is compatible with this system. ( 30) Turn this system off and then on again. If the main unit is connected to the TV with only an HDMI cable, make sure that the TV s HDMI terminal is labelled HDMI (ARC). If not, connect using the optical digital audio cable. ( 16) If the main unit is connected to a Panasonic TV and turned on using the button on the main unit or the remote control, sound might not be output from this system. In this case, turn the main unit on using the TV s remote control. ( 22) If the connections are correct, there might be a problem with the cables. Redo the connections with different cables. Check the audio output settings on the connected device. If the BD/DVD indicator flashes and there is no audio output, try the following. 1 Turn the connected device off and then on. 2 Turn off the main unit, remove the HDMI cable, then reconnect the HDMI cable and turn the main unit back on. The dual audio cannot be changed from main to secondary. If the audio received from the connected device is not Dolby Dual Mono or the output setting is not Bitstream, the setting cannot be changed from this system. Change the setting on the connected device. The volume is lowered when the main unit is turned on. If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically lower the volume to the middle (50) when the main unit is turned on. ( 25) The dialog is too persistent or the dialog does not sound natural. This system has a function to make the dialog stand out when the volume is low. ( 25) There is no audio. The power of the main unit turns off automatically. (When the main unit detects a problem, a safety measure is activated and the main unit automatically switches to standby mode.) There is a problem with the amplifier. Is the volume extremely high? If so, lower the volume. Is this system placed in an extremely hot place? If so, move this system to a cooler place and wait a few moments and then try to turn it on again. If the problem persists, confirm the TV indicator and BD/DVD indicator blink, turn this system off, remove the AC mains lead cord and consult your dealer. Please be sure to remember the indicators that were blinking and inform the dealer. 28

Indicator illumination The indicators display the condition of this system by flashing. The indicator patterns illustrated below are displayed during normal operational conditions. They do not refer to the indications of a problem. Indicator *1 Description The indicator blinks for 10 sec. When the Bluetooth communication is mode 1 ( 23) The indicator blinks for 20 sec. When 3D surround effect and clear-mode dialog effect are on ( 24) When the dual audio setting is Main ( 23) When the auto gain control is on ( 23) When the auto standby function is on ( 24) The indicator blinks for 5 sec. When the audio format is Dolby Digital ( 23) *1 The indicator blinks for 5 sec. When the audio format is DTS ( 23) *1 The indicator blinks for 5 sec. When the audio format is PCM* 2 ( 23) The indicator blinks for 10 sec. When the Bluetooth communication is mode 2 ( 23) The indicator blinks for 20 sec. When 3D surround effect and clear-mode dialog effect are off ( 24) When the dual audio setting is Secondary (SAP: Secondary Audio Program) ( 23) When the auto gain control is off ( 23) When the auto standby function is off ( 24) The indicators blink for 20 sec. When the dual audio setting is Main and Secondary ( 23) *1 The indicators blink for 10 sec. When the remote control code is changed ( 25) The indicators blink once. When changing the setting ( To reduce the clear-mode dialog effect, To turn off VIERA Link HDAVI Control, and To turn off the volume limitation ) ( 25) The indicators blink twice. When the main unit is reset ( 26) Bluetooth indicator blinks quickly. When the main unit is ready for pairing Bluetooth indicator blinks slowly. When the main unit is waiting to connect Bluetooth indicator turns on. When the main unit is connected with a Bluetooth device *1 The indicator for the current status remains lit. *2 The indicator blinks only when [SOUND] is pressed for more than 4 sec and the audio format is PCM. Reference 29

Specifications AMPLIFIER SECTION RMS output power: Dolby Digital Mode Front ch 30 W per channel (6 ), 1 khz, 10 % THD Subwoofer ch 60 W per channel (3 ), 100 Hz, 10 % THD Total RMS Dolby Digital mode power 120 W TERMINAL SECTION HDAVI Control This unit supports HDAVI Control 5 function. HDMI AV input (BD/DVD) 1 Input connector Type A (19 pin) HDMI AV output (TV (ARC)) 1 Output connector Type A (19 pin) Digital audio input Optical digital input Optical terminal Sampling frequency 32 khz, 44.1 khz, 48 khz 88.2 khz, 96 khz (only LPCM) Audio Format LPCM, Dolby Digital, DTS Digital Surround IR Blaster Terminal Type 3.5 mm jack USB Port For service use only. SPEAKER SECTION Front speakers (Built-in) Type 2 way, 2 speaker system (Bass Reflex) Woofer 5.7 cm Cone type Tweeter 2.5 cm Semi-dome type Subwoofer (Built-in) Type 1 way, 2 speaker system (Bass Reflex) Woofer 8cmConetypek2 GENERAL Power consumption 22 W Power consumption in standby mode (When the other connected devices are turned off) Approx. 0.4 W Power supply AC 220 V to 240 V, 50 Hz Dimensions (WkHkD) 950 mmk66 mmk105 mm Mass Approx. 3.4 kg For wall mounting Dimensions (WkHkD) 950 mmk105 mmk66 mm Mass Approx. 3.4 kg With basic stands Dimensions (WkHkD) 950 mmk79 mmk105 mm Mass 3.45 kg With 30 o stands Dimensions (WkHkD) 950 mmk99 mmk113 mm Mass 3.45 kg With 80 o stands Dimensions (WkHkD) 950 mmk118 mmk80 mm Mass 3.47 kg Operating temperature range 0 o C to i40 o C Operating humidity range 20 % to 80 % RH (no condensation) Bluetooth SECTION Bluetooth system specification Version 3.0 Wireless equipment classification Class 2 Supported profiles A2DP Frequency band 2400 MHz to 2483.5 MHz (Adaptive Frequency Hopping) Operating distance 10 m Line of Sight Specifications are subject to change without notice. Weight and dimensions are approximate. Total harmonic distortion is measured by a digital spectrum analyzer. 30