800 W ax 500 W ax 500 W ax 500 W ax Zone 1 Zone 2 Zone 3 Zone 4 Option Def H Opt1 Opt2 Opt3 230 V~ 50 / 60 Hz 10 A www. H H G G Switching Power odule The DI Power odule (DP) family is a group of modular products for the control of lighting loads. This product is compatible with utron systems. This document describes the following product: : 4-zone power module for switching only. Features system capability only. Four switched output zones. Adaptive zero-cross switching maximizes relay life. Rated for the following lighting loads: Incandescent, agnetic ow Voltage (V), Electronic ow Voltage (EV), Electonic Ballasts and ED Drivers. Rated for motor loads of 1/2 HP. Includes QS link. Does not supply power on the QS link. EDs on the module provide diagnostic information. Buttons on module provide override control. Emergency Contact Closure Input (). Programmable Contact Closure Output (CCO). Power failure memory. +1.844.UTRO1 CO CCO CO Switching Power odule UX UX CO 3691079b 1 06.05.18 220-240 V~ 5 A 220-240 V~ 5 AX, 1/2 HP System Example seetouch QS Wallstation Dimming Power odule QS Contact Closure Interface GRAFIK Eye QS Contact Closure Output Input anual Override Contact Closure Input Hi Temp Prog Power Switching Power odule CO +1.844.UTRO1 CCO CO UX UX CO 220-240 V~ 5 A 220-240 V~ 5 AX, 1/2 HP QS ink 500-10561 Rev. B Processor and Power Supply Up to 100 QS devices Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule Specifications Power 220 240 V~ 50/60 Hz Single input feed 16 A maximum input current ightning strike protection meets ASI/IEEE standard C62.41 and IEC 61000-4-5. Can withstand voltage surges up to 6000 V~ and current surges up to 3000 A ESD-protection exceeds agency requirements per IEC-61000-4-2 For ungrounded delta feed applications, contact utron Regulatory Approvals Complies with IEC/E 60669 utron Quality Systems registered to ISO 9001.2015 CE arked RoHS Compliant Environment For thermal specifications, see ounting section Relative humidity: less than 90% non-condensing For indoor use only Terminals ains wiring: 1.0 mm² to 2.5 mm² (18 AWG to 12 AWG) (single wire, solid or stranded) / CCO wiring: 0.5 mm² to 2.5 mm² (22 AWG to 12 AWG) (single wire, solid or stranded) 0.5 mm² to 1.5 mm² (20 AWG to 16 AWG) (two wires, solid or stranded) Zone wiring: 1.0 mm² to 2.5 mm² (18 AWG to 12 AWG) (single wire, solid or stranded) QS ink: 0.5 mm² to 2.5 mm² (22 AWG to 12 AWG) (single wire, solid or stranded) 0.5 mm² to 1.0 mm² (20 AWG to 18 AWG) (two wires, solid or stranded) 3691079b 2 06.05.18 Programming and Compatibility Requirements Setup and programming of the Switching odule is done through the programming software software version 3.4 or higher is required QS ink imits A QS link in a system can have up to 512 zones (outputs) and 100 devices (required processor counts as 1 device on the QS link) Each Switching odule counts as one device toward the 100 device limit, and 4 zones toward the 512 zone limit For more information, see the Commercial System Rules specification submittal (P/ 369821) at www. Output Zone Ratings Each zone is rated at 5 A for switching. Rated for resistive, inductive, or capacitive lighting loads as defined by IEC/E 60669 Air gap off per output o minimum load per output This module is designed to control loads with ratings as noted in the table below Outputs cannot be used to control general purpose receptacles oad Type Tungsten AC General Use Electric Discharge amp Electronic Ballast Resistive Inductive otor Relay Ratings 220-240 V~ 5 A (1/2 HP)/zone, 16 A max/module Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule Specifications - (continued) 3691079b 3 06.05.18 Special considerations: When controlling lamps, utron recommends using permanently installed fixtures. If controlling plug-in lamps, installation must ensure a method of preventing non-rated loads being plugged into the unit. An example is a dedicated receptacle with a mating plug type. Controlling loads outside the parameters listed in the specifications may damage the device and void the warranty. If attempting to control general purpose receptacles, use the appropriate third-party power pack for the rated load. Run a separate neutral for each load circuit. A common neutral connection is not recommended. Unit may be powered by a Ground Fault Interrupter (GFI) or Residual Current Circuit Breaker with Overload (RCBO) protected circuit if required. For applications requiring higher wattage ratings, use GRX-TVI or QSE-4S10-D for 220 240 V~. Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule anual ode Operation 3691079b 4 06.05.18 Zone buttons on the unit can be used to turn loads on and off. Emergency Contact Closure Input () When the is open, the Switching Power odule will enter Emergency ode, which will turn all the zones on and disable control of all local zones from any QS device. When the is closed or jumpered (factory default), the Switching Power odule zones will return to the settings they were at prior to entering Emergency ode. Contact Closure Output (CCO) Accepts voltages of 0 24 V~ / 0 24 V-; see chart below for load switching capacities: Switching Voltage Resistive oad R 0 24 V- 1.0 A 0 24 V~ 0.5 A Provides both normally open (.O.) and normally closed (.C.) dry contacts. aintained or momentary output type. Output relay is non-latching (if relay is closed and power is lost, relay will open). The CCO is not rated to control unclamped, inductive loads. Inductive loads include, but are not limited to, relays, solenoids, and motors. To control these types of equipment, a flyback diode (not included) must be used (DC voltages only). See diagram below. Flyback Diode (required for inductive loads) Inductive oad +.O. CCO Output CO.C. 24 V- maximum Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule ounting ount in a utron DI Panel (see P/ 369783 at www.) or in an IP20 (minimum) rated consumer panel or breaker panel with integrated DI rail. Unit is 9 DI (161.7 mm [6.37 in]) wide. ount in an accessible and serviceable location. Unit may be mounted by pressing the unit onto the DI rail with the clips locked. To remove the unit from the DI rail, unlock the clips using a screwdriver. See utron P/ 048466 at www. for more information on mounting and installation in panels with integrated DI rail. ount the Power odule where audible noise is acceptable (internal relays click). Unit generates heat, maximum 24 BTU/h. ount unit such that all the conditions below are met: Room ambient temperature is between 0 ºC and 40 ºC (32 ºF and 104 ºF). Temperature inside mounting panel, within 20 mm (0.80 in) of unit, is between 0 ºC and 40 ºC (32 ºF and 104 ºF). Calibration point maximum: 65 ºC (149 ºF). echanical Dimensions Prog. Prog. Zn. Zn. 1 1 Zn. Zn. 2 2 Zn. Zn. 3 3 Zn. Zn. 4 4 QS QSE-4S1-D 220 240 V~ 50 60 Hz 16 120 120-240 - 240 V~ V~ 50 50 / 60 / 60 Hz Hz 44 AA +1.844.UTRO1 CO CO CCO CO CCO CO UX UX UX UX CO CO IEC IEC SEV SEV / / ECR ECR Class Class 2 2 ounting clips (4) on unit ocked Unlocked 3691079b 5 06.05.18 120 120 220-240 - 240 V~ V~ 1 1 A 5 A 120 120 220-240 - 240 V~ V~ 1 1 AX, 5 AX, 1 1 FA 1/2 FA HP / 6 / 6 RA RA +1.844.UTRO1 CO CCO CO UX UX CO 220-240 V~ 5 A 220-240 V~ 5 AX, 1/2 HP 89.7 mm (3.53 in) 60.6 mm (2.38 in) 161.7 mm (6.37 in) Calibration point location on the side of the enclosure Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule Wiring: ains and Output Zones 3691079b 6 06.05.18 Wiring from Distribution to Switching Power odule Turn off all circuit breakers or isolators feeding the Switching Power odule at the distribution panel. Run line / hot and neutral wires from a 220 240 V~ 50 / 60 Hz feed to the Switching Power odule unit. Run a separate neutral for each load circuit. A common neutral connection is not recommended. ains Wiring and IEC SEV Separation Follow appropriate local and national codes to avoid violating required separation guidelines. IEC SEV CCO QS ink Zn. 3 Zn. 4 QS +1.844.UTRO1 0 / 60 Hz 4 A 282.3800 CO CO CCO CO UX UX CO CCO CO 220-240 V~ 5 A 220-240 V~ 5 AX, 1/2 HP UX ains eutral Outputs UX CO IEC SEV / ECR Class 2 120-240 V~ 1 A 120-240 V~ 1 AX, 1220 FA -/ 240 6 RA V~ 5 Distribution Panel 220 240 V~ ine/hot eutral To additional modules ote: If wiring for feed-through to other utron modules using mains terminals, total current of all modules must be less than or equal to 16 A. Zone 1 Zone 2 Zone 3 Zone 4 Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule Wiring: Emergency Contact Closure Input and Contact Closure Output IEC SEV Contact Closures Emergency Contact Closure Input () / Contact Closure Output (CCO) wiring is IEC SEV. Follow all applicable national and local codes for proper circuit separation and protection. Turn off all breakers or isolators feeding the Switching Power odule at distribution panel before servicing unit. Pre-installed Jumper CO Wiring CCO CO UX UX CO Prog. Zn. Zn. 11 Zn. Zn. 22 Zn. Zn. 33 Zn. Zn. 44 QSE-4S1-D 120-240 V~ 50 / 60 Hz 4 A +1.844.UTRO1 CO Prog. Zn. 1 Zn. 2 Zn. Prog. 3 Zn. Zn. 4 1 Zn. 2 Zn. 3 Prog. Zn. 4 Zn. 1 Zn. 2 Zn. Prog. 3 Zn. Zn. 4 1 Zn. 2 Zn. 3 Zn. 4 IEC SEV / IEC SEV / ECR Class 2 QSE-4S1-D OR 120-240 V~ 50 / 60 Hz 4 A Device Wiring CCO CO CO CO CCO CO CCO CO UX UX UX UX UX UX CO CO ECR Class 2 is local control only and cannot HomeWorks control other units over the QS link. QS on up to 32 units may QSE-4S1-D be connected QSE-4S1-D to an QSE-4S1-D QSE-4S1-D 120-240 V~ 50 / 120 60 Hz - 240 4 V~ A 50 / 60 Hz 4 A emergency or manual override device in parallel if event is intended to affect multiple units. When in Emergency ode: All zone outputs will be switched on. Controls will not affect units in Emergency ode. Controls connected to a unit in Emergency ode will continue to affect units on the link that are not in Emergency ode. Emergency contact closure input is normally closed (.C.). The Switching Power odule is shipped Prog. with Zn. a jumper 1 Zn. 2 Zn. 3 Zn. 4 pre installed. ote: The Switching Power odule will default to Emergency ode if the is left open. If no Emergency contact input is required, leave the wire jumper in the terminals. CO CO IEC SEV / ECR Class 2 3691079b 7 06.05.18 120-240 V~ 1 A 120-240 V~ 1 A 120-240 120-240 V~ 50 / 120 60 Device Hz - 240 4 V~ A Wiring 50 / 60 Hz 4 A CCO (.O.) 120-240 V~ 1 AX, 1 FA 120 / - 6 240 RA V~ 1 AX, 1 FA 120 / 6 - RA 240 CO CCO (.C.) 1 2 3 4 CO 1 2 3 4 1 2 Third-party Device Third-party Device CO CCO Wiring.O. Wiring OR.C. Wiring CCO CO CCO CO UX UX UX CO UX CO CCO CO 120 220-240 - 240 V~ V~ 15 A A 120 220-240 - 240 V~ 15 AX, AX, 1 1/2 FA HP / 6 RA IEC SEV / ECR Class 2 CO UX UX IEC EC Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber:
Switching Power odule Wiring: QS ink QS link wiring is IEC SEV. Follow all applicable local codes for proper circuit separation and protection. Turn off all breakers or isolators feeding the Switching Power odule at distribution panel before servicing unit. Wiring may be daisy chained or t-tapped. Wire Gauge: Control (terminal 1): 0,5 mm 2 to 2,5 mm 2 (22 AWG to 12 AWG) single wire, solid or stranded. Data (terminals 3 and 4): 1 pair 0.5 mm 2 to 1.0 mm 2, (22 AWG to 18 AWG) twisted and shielded. Control ink 1: CO 2: Do ot Connect Data ink 3: UX 4: UX QSE-4S1-D Prog. Prog. Zn. Zn. 1 1 Zn. Zn. 2 2Zn. Zn. 3 3 Zn. Zn. 4 4 CO CO CCO CO CCO CO Can use utron cable GRX-CB-346S-500 (less than 152 m [498 ft]) or GRX-CB-46 (152 m to 610 120-240 V~ QSE-4S1-D 50 / 60 Hz 4 A 220 240 V~ 50 / 60 Hz 16 120-240 V~ 50 / 60 Hz 4 A m [498 ft to 2001 ft]). See Power Draw Units (PDUs) on the QS ink specification submittal (P/ 369405) at www. For adherence to ow Smoke Generation (E60332-1-2), Halogen Gas Emission (E61034-2), and Flame Retardation (E60754-1 & -2), use QS-CB-52H-500 (less than 152 m [498 ft]). +1.844.UTRO1 CO UX UX UX UX CO CO CCO CO IEC SEV / ECR Class 2 3691079b 8 06.05.18 UX 220 120-240 - 240 V~ V~ 5 1 A A 220 120-240 - 240 V~ V~ 5 1 AX, AX, 1/2 1 FA HP / 6 RA UX CO IEC EC )utron, utron, seetouch,, and GRAFIK Eye are trademarks of utron Electronics Co., Inc., registered in the U.S. and other countries. Job ame: SPECIFICATIO SUBITTA odel umbers: Job umber: