SXT2010 20.1 SXGA TFT NEMA 4/12 Flat Panel Monitor User s Guide 302010(A) (was document no. 920A0007 version 1.0), revised 12/98 Viewtronix
Viewtronix reserves the right to make changes in specifications described herein at any time without notice in order to improve design and reliability. Viewtronix does not assume any responsibility for the use of any circuitry described; no circuit patent licenses are implied. Viewtronix assumes no responsibility for damage caused by misuse or improper use of its products. WARRANTY Viewtronix warrants to Customer that the Products will be free from defects in material and workmanship under normal use and service for a period of one year from date of invoice. Customer s exclusive remedy for breach of this warranty is that Viewtronix will either (i) repair or replace, at its option, any Product which fails during the warranty period because of such defect (if Customer promptly reported the failure to Viewtronix in writing) or, (ii) if Viewtronix is unable to repair or replace, Viewtronix will refund the purchase price of the Product upon its return to Viewtronix. This warranty does not apply to any Product which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction, or which has been serviced by anyone other than Viewtronix. The warranty set forth herein is in lieu of, and exclusive of, all other warranties, express or implied. Document No. 302010(A) (was 920A0007 version 1.0) Released 12/98 2
Table of Contents Introduction...4 Video Modes Supported...4 Specifications...5 Front and Side View of Monitor...6 Installation of Monitor...6 Mode and Image Adjustment...7 Front Panel Controls...8 Menu System Description...9 Status of the Display...11 VGA Input Connector Pin Out...12 3
Introduction The SXT2010 is a 20.1 SXGA (1280 x 1024) TFT industrial flat panel monitor for use in NEMA 4 and NEMA 12 applications. Graphics and text can be displayed on the monitor in true color and in the modes listed below. When the monitor is being driven in modes other than SXGA, it will automatically expand the image and center it on the LCD. The unit is fully self-contained needing only to be panel mounted in an appropriate enclosure and connected to 120/240 VAC and a VGA source. The monitor features a bright 180-nit LCD display and conveniently located front panel controls with on screen menus for easy set up and adjustment. The unit is designed to provide tool free access for quick back light replacement and cleaning. The SXT2010 is available with optional integrated analog resistive touch screen and/or a 304 stainless steel bezel. Video Modes Supported MODE HORIZONTAL SYNC RATE khz VERTICAL SYNC RATE Hz DOT FREQUENCY MHz EXPANSION FACTOR VGA 640 x 480 31.468 59.941 25.175 2 VGA 720 x 400 31.468 70.087 28.322 1.7 Mac 640 x 480 35.00 66.67 30.24 2 Mac 832 x 624 49.73 74.55 57.28 1.25 Mac 1152 x 870 68.68 75.06 100.0 1 VESA 640 x 480 37.86 72.81 31.5 2 VESA 640 x 480 37.50 75.00 31.5 2 VESA 640 x 480 43.27 85.01 36.0 2 VESA 800 x 600 35.16 56.25 36.0 1.5 VESA 800 x 600 37.88 60.32 40.0 1.5 VESA 800 x 600 48.08 72.01 50.0 1.5 VESA 800 x 600 46.88 75.00 49.5 1.5 VESA 1024 x 768 48.36 60.00 65.0 1.25 VESA 1024 x 768 56.48 70.07 75.0 1.25 VESA 1024 x 768 60.02 75.03 78.75 1.25 VESA 1024 x 768 68.68 85.00 94.5 1.25 VESA 1280 x 1024 63.98 60.02 108.0 1 VESA 1280 x 1024 79.97 75.02 135.0 1 4
Specifications DISPLAY PARAMETER Display Size Active Area Pixel Format Brightness Back Light Life Contrast Ratio Number Colors SPECIFICATION 20.1 Diagonal 15.72 (H) x 12.58 (V) 1280 (H) x 1024 (V) Pixels (1 Pixel = R + G + B Dots) 180 Nit Typical 15,000 Hrs 100:1 Typical Full Color PHYSICAL PARAMETER Monitor Outside Dimensions Monitor Weight Operating Temperature Storage Temperature Relative Humidity Operating Vibration Operating Shock Operating Altitude SPECIFICATION 17.18 (H) x 20.32 (W) x 4.75 (D) 28 Pounds 0 ~ 50 Degrees Centigrade -20 ~ 60 Degrees Centigrade < 95%, Ta < 40 Degrees Centigrade, < 85%,40 < Ta < 50 Degrees Centigrade 5 ~ 500 Hz, 1G 15G for 11ms 10,000 Feet Above Sea Level ELECTRICAL PARAMETER SPECIFICATION Input Voltage Input Power 90 ~ 264 VAC, 47 ~ 440 Hz 90 W Compliance Parameter Specification NEMA Rating EMC Safety NEMA 4/12 From front when properly installed in an enclosure. FCC Part 15, Class A / Industry Canada ICES-003 Issue 2, Rev. 1 / EN61000-4-2, 4-3, 4-4 / EMC Directive 89/336/EEC (Pending) UL-1950 / CUL/CSA 22.2 950 M93/ EN60950 / Low Voltage Directive 73/23/EEC (Pending) 5
I Front and Side View of Monitor Viewtronix 17.18" O 20.32" 4.50" Installation of Monitor This monitor is intended to be mounted in and used where NEMA 4 and NEMA 12 type enclosures are employed. When mounted properly, the monitor meets or exceeds the sealing requirements set forth in the NEMA 4 and NEMA 12 specifications. The monitor uses U -shaped clips and a special gasket to achieve the proper seal. To install the monitor, make a cutout per the diagram below in one of the walls of your NEMA enclosure. Enclosures made of heavier gauge metal work better in that they won t deform or bend as easily when the monitor s sealing gasket is compressed. Next hold the monitor in place while you install the mounting clips. Tighten the clips in a cross pattern. This will help to develop an even pressure on the sealing gasket. Tighten the clips to the point were the back of the monitor s front bezel just begins to contact the front of the NEMA enclosure. DO NOT OVER TIGHTEN AS DAMAGE CAN RESULT IN THE MONITOR CAUSING LOSS OF SEALING INTEGRITY. APPLICATION NOTE: TO REDUCE THE AFTER-IMAGE EFFECTS CAUSED BY STATIC IMAGES BEING DISPLAYED FOR PROLONGED PERIODS OF TIME, WE RECOMMEND SOME FORM 0F SCREEN SAVER BE USED. 6
Cutout Pattern for Monitor 16.40" +/-.02" 19.55" +/-.02" Mode and Image Adjustment Not all video controllers produce exactly the same video output levels or the same timing. The following procedure can be used to select the desired video mode as well as optimize your monitor s image quality. When adjusting your monitor, the use of video test software such as DisplayMate for Windows by SONERA Technologies can be very beneficial. Before connecting the SXT2010 to your computer, adjust your desk top display settings to the following: Colors: 256 Vertical Refresh: 60Hz Resolution: 1280 x 1024 Monitor Type: Viewsonic 15 After connecting the SXT2010 to your computer you should first adjust the monitors horizontal size (or width) using the Hsiz menu selection. Next you should use the Hpos and Vpos menu selections to center the image on the LCD. After this, use the Clka menu selection to focus the screen s image. Finally, use the SAVE menu selection to store the monitor s settings in no-volatile memory. 7
Front Panel Controls Mode Display Power Button MENU SELECT INCREASE DECREASE Menu Control Contrast & Menu Select Brightness & Menu Adjustment BUTTON FUNCTION MENU Menu Control. Changes Contrast and Brightness buttons to Menu and Enter Buttons or back to Contrast and Brightness functions respectively. CONTRAST Dual function, Contrast and Menu Select. Function 1: Contrast (10 Levels). Function 2: Menu Select (i.e. V-Pos, H-Pos, H-Size etc.) Two buttons: and. BRIGHTNESS POWER Dual function, Brightness and Menu Adjustment functions. Function 1: Brightness (2 Levels). Function 2: Adjustment of selected menu item. Two buttons: and. Power Button. Turns main power to converter card and panel on and off. Note: Pressing both Contrast buttons simultaneously will jump you to the top menu level but not change any menu positions previously selected. Pressing the Brightness buttons simultaneously will take you down the menu tree in the same order as done previously. This saves keystrokes if you want to go up a level. Pressing the Menu button twice will reset all menu positions and place you at the top menu level. When the unit is first powered on or the Alpha display timer, times out, in 15 seconds the menu positions are reset and the buttons are restored to Contrast and Brightness Functions. 8
Menu System Description After the Menu Key is pressed the word MENU appears on the display. Using the Menu and buttons causes the following menu options to appear. First Level Menu Hpos Hsiz Vpos ClkA Save Horizontal Position Adjustment (Use the Brightness or button to adjust) Horizontal Size Adjustment (Use the Brightness or button to adjust) Vertical Position Adjustment (Use the Brightness or button to adjust) Clock Adjustment of Focus (Use the Brightness or button to adjust) Save Setting (Use the Brightness or button to select the save menu) Sub Menu for Saving Settings After selecting the Save option, press the Contrast or buttons to select one of the following three options: Sys0 Usr1 Usr2 (This is the default boot up setting) (This is user 1 setting) (This is user 2 setting) Once you have selected the location to which the settings will be saved, press either Brightness button to save. Rsto Restore settings menu (Use the Brightness or button to select the Restore menu) Sub Menu for Restoring Settings After selecting the Rsto option press the Contrast or buttons to select of the following four options: Dflt Sys0 Usr1 Usr2 (This is the factory default setting) (This is the default boot up setting) (This is a user selectable setting) (This is a user selectable setting) Once you have selected the location from which to restore settings, press either Brightness button to restore. 9
SetU Setup menu (Use the Brightness or button to select the Setup menu) Sub Menu for Setup After selecting the SetU option press Contrast or buttons to select one of the following four options: Sync (Type of Sync input. Use the Brightness or buttons to select the sync type) Sub Menu for Sync After selecting the Sync option press the Contrast or buttons to select on of the four following options: Auto 5wir 4wir 3wir (This setting will automatically detect the actual video sync type) (This setting will select 5-wire video only) (This setting will select 4-wire video only) (This setting will select 3-wire video only) Once you have selected the Sync option, press either Brightness button to save settings. Dclr Diag (This disables the 15 second automatic alpha display clear and menu reset function.) The Brightness button enables the clear function and the Brightness button disables the clear function. The display will show on or off after the appropriate button is pressed. (This setting is for diagnostic testing) Sub Menu for Diag. After selecting the Diag option, press the Contrast and buttons to select one of the following eleven options: Bds# Time Bklt Butn Dspy R232 Hlin Vcnt (This is the converter board serial number) (This is the amount of time the board has been powered on in hours. The timer can keep track of up to 99,999 hours which is equal to 11.4 years of continuous use) (This toggles the backlight on and off) (This tests the front panel buttons) Pressing either Brightness button places you in the button test mode. Note: If you press the power button it will shut off the panel. You must press both Contrast buttons simultaneously to exit the buttons test. (This tests the alpha display) Pressing either Brightness button will cycle you through 128 ASCII characters on the alpha display. (This tests the internal RS232 port) With a loop back connector installed PASS or FAIL will be displayed on the alpha display. This feature is not available on the SXT2010. (This displays the horizontal line count) The value is the hexadecimal number of horizontal lines per vertical period. (This displays the vertical count) The value is the hexadecimal vertical period count at 500ns per count. 10
Mode Ptc# Rev# (This displays the video mode) (This displays the factory panel type setup) (This displays the version of micro code installed on the converter card) Status of the Display The alpha display will report the status of the converter card. The following is an explanation of each of the messages. Sync Flashing When you see the word Sync flashing, the monitor does not detect sync present of you have selected a specific sync type that is not supported by the video source.. Small Dot This is the power on indicator. It also indicates no errors present. VGAT This indicated the video source is in VGA DOS Text Mode (640 x 400). VGA This indicated the video source is in VGA Mode (640 x 480). SVGA This indicated the video source is in SVGA Mode (800 x 600). XGA This indicated the video source is in XGA DOS (1024 x 768). SXGA This indicated the video source is in SXGA Mode (1280 x 1024). Undf Rang Rest Flashing Cold Flashing Menu When you see this on the display the video resolution is undefined. This indicates the video source is either a format not supported by the monitor, is corrupt, or the sync type selected is set to 3-wire mode, but the source is either a 4-wire or 5-wire type. When you see this on the display the backlight is turned off. When you see this on the display the temperature is too cold for the panel to function. You must wait for the panel to reach operating temperature before the panel will begin functioning. When you see this on the display you are at the top level of the menu tree. 11
VGA Input Connector Pin Out SIGNAL NAME 15-PIN D-SHELL (FEMALE) Red 1 Green 2 Blue 3 4 GND-Digital 5 GND-Red return 6 GND-Green 7 return GND-Blue return 8 9 GND-Digital 10 11 12 Hsync 13 Vsync 14 15 12
Xycom Automation, Inc. 734-429-4971 Fax: 734-429-1010 1-800-AT-XYCOM http://www.xycom.com Northern Europe Sales: +44-1604-790-767 Southern Europe Sales: +39-011-770-53-11 2001 Xycom Automation, Inc. All rights reserved. Printed in US. All brand or product names are the property of their respective owners. Specifications may change without notice.