Audio In IR Out Local IR In Audio & IR Control CA5 ransceiver 0
he Audio & IR Control CA5 ransceiver Kit can deliver balanced audio and IR signals over,000 ft of CA5 cable. It s the perfect way to send noise-free audio over cabling that already exists in the home. he decorator style wall plates flush mount into the wall and blend into modern decor. he low cost, simplicity, and availability of CA5 cable, makes the a convenient choice for both new construction and retrofit applications. Features: heasy to install and use hransport audio from a bedroom back to your main entertainment system hcontrol the audio device in the bedroom from your entertainment room hsends line-level audio over 000 ft. of category cable hcompatible with Category 5, 5e, and 6 wiring Input Wall Plate Output Wall Plate Audio In IR Out Local IR In IR Receiver Input IR Emitter Output Audio Input CA5 Outputs -se only one (not both) IR Receiver Input Power Supply Input Audio Input Power Input Power Loopout CA5 Outputs -se only one (not both) 2
Installation Connect the power supply Single Gang Ring CA5 cable,000 max. se mounting screws to attach the to the low voltage ring. Single Gang Ring Standard decorator trim plate (Not Included) Brightness Brightness Standard decorator trim plate (Not Included) se mounting screws to attach the to the low voltage ring. he power for the can be looped as shown below to allow one power supply to serve up to 0 units. he power supply can be connected in the front or the rear.
CHANNEL VISION MODEL A0505 ZONE POWER CAV MOD CAMERA VOL POWER S O R C E ME 2 4 2 4 Basic Application Input Wall Plate Connect an additional IR receiver here to allow control of the audio device even if it is behind a closed cabinet door. Audio In IR Out Local IR In CD player Audio source located in a remote location. CA5 cable up to,000ft. Audio Amplifier Pwr. IR receiver (optional) Output Wall Plate A0505 Note: A standalone IR receiver Remote or an IR output from a whole-house IR system can also be connected here. 4
Advanced Application Input Wall Plate Connect an additional IR receiver here to allow control of the audio device even if it is behind a closed cabinet door. Audio In IR Out Local IR In CD player Audio source located in a remote location. CA5 cable up to,000ft. Pwr. When using with the A462 or A460 connect the RCA outputs to the source Input jacks and connect the IR In jack to any of the IR Emitter output jacks using an IR-480 cable. his will allow the remote audio source to be listened to and controlled from any of the audio zones. he IR receiver in the audio system keypads will pass IR signals back to the input wall plate. Output Wall Plate IR-480 Cable IR Emitter Out Source Input 5 POWER 6 Control 5 4 Control 2 Control Serial IR Emitters Link Input Voltage S O P E A P K E R S O O O Hi-Z 5 I 75 N 2 4 P P P P 6 4 2 4 2 C R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO R-ADIO-L VIDEO + R - - L + + R - - L + + R - - L + + R - - L + + R - - L + + R - - L + Warning: Channel Vision A462 o prevent fire or shock hazard do not expose this unit to rain or moisture. ested o Comply With FCC Standards CAION FSE RISK OF ELECRIC SHOCK FOR HOME OR OFFICE SE 6 5 4 2 DO NO OPEN.5AL/250V 5VAC S 20/5V 50/60 Hz MAX 5W ~ 5
Pin-out Configuration For Blue Stripe Blue Solid Orange Stripe Orange Solid Green Stripe Green Solid Brown Stripe Brown Solid Ground IR Signal - + - + Power + Ground IA568A Green/white Green Orange/white Blue Blue/white Orange Brown/white Brown 2 4 5 6 7 8 PINS Pins Signal - 2 + - 4 IR Signal 5 Ground 6 + 7 Ground 8 Power + View into jack 6
Stripping and Connecting CA5 Wire CA5 cable should be stripped with a proper stripping tool, such as Channel Vision s J-0 tool.. Place the CA5 between the blade and the first notch of the J-0 tool. CA5 Blade 2. Rotate the tool only once. Multiple turns could damage the inner wires.. Inspect the inner wires for damage. If any wires are cut start over at step. Rotate turn only Check for damage Slight pressure IA-568A RJ-45 Modular Plug Side view: op view: Green/White - channel ground Green - channel Orange/White - channel ground Blue - Signal Blue/White - Status Orange - channel Brown/White - Ground Brown - 24vDC
roubleshooting ) Be sure you have connected the CA5 cable correctly. Follow the IA-568A standard at both ends. Incorrect wiring can cause distorted sound or prevent the system from working at all! 2) Be sure you have connected the speakers in phase. Follow the label on the product. Out of phase speakers can deprive the system of its bass. Especially when driving dual-voice-coil speakers. ) rouble with IR control? a. Make sure your IR remote control can control the source device directly (not using the IR repeating system). b. Verify that the IR emitter is providing a signal to your source device. Many IR emitters do not provide visible light. You can see these invisible IR signals if you look at the IR emitter through the view finder of a digital camera (it helps to turn the lights off). c. roubleshooting an external IR system: Some IR receivers have a feedback LED that flashes whenever IR signals are received. If the IR receiver you are using has this feature, check to make sure the LED flashes whenever you press buttons on your remote control. i. If you don t see the feedback LED, try replacing the batteries in your remote control. 4) Observe wiring distance specifications. he maximum recommended wire length between the wall dock and output wall plate is,000 feet. Although the may work at longer distances, such extreme distances are not recommended because erratic performance may result due to the power loss caused by the CA5 wire. 5) If you need additional help troubleshooting the, please contact Channel Vision technical support or check our website for more details: www.channelvision.com. Specifications: HD + Noise: <0.2%, 20Hz-20kHz Signal/Noise: >-96dB Frequency Response: 20Hz-20kHz +/- 0.dB Input Impedance: 20k Ohms Output Impedance: 600 Ohms Power Requirements: 5VDC @ 0.075A (75mA) Power Supply: 5VDC @ 850mA Wire type: 4-pair, P Category 5, 5e or 6 Maximum Cable Run:,000 ft. over CA5 Specifications subject to change without notice. 7
Channel Vision echnology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the SA, for one year from the date of original purchase. his is a no hassle warranty with no mail in warranty card needed. his warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision echnology, or failures due to accident, misuse, abuse, or alteration of the equipment. his warranty is extended only to the original purchaser, and a purchase receipt, invoice, or other proof of original purchase date will be required before warranty repairs are provided. Mail in service can be obtained during the warranty period by calling (74) 424-6500. A Return Authorization number must be obtained in advance and can be marked on the outside of the shipping carton. his warranty gives you specific legal rights and you may have other rights (which vary from state to state). If a problem with this product develops during or after the warranty period, please contact Channel Vision echnology, your dealer or any factory-authorized service center. Channel Vision products are not intended for use in medical, lifesaving, life sustaining or critical environment applications. Channel Vision customers using or selling Channel Vision products for use in such applications do so at their own risk and agree to fully indemnify Channel Vision for any damages resulting from such improper use or sale. w w w. c h a n n e l v i s i o n. c o m 24 Fischer Avenue, Costa Mesa, California 92626 SA (74)424-6500 (800)840-0288 (74)424-650 fax email: techsupport@channelvision.com 500-277 rev B