Electronic Equipment Manual For 204, 213, 215, 217, 219, 234 & 432 Tory Building, 146, 149, 204, 243 Loeb Building and 316, 318 & 501 Southam Hall For further information, please visit our website at: http://www.carleton.ca/ims/
2 TABLE OF CONTENTS: Topic Page # Starting the Data Projector 3 Using the Console Computer 3 Using a Laptop 4 Adjusting the Volume 4 Blanking the Image on the Data Projector 5 Using the VCR 5 Using the DVD Player 6 Connecting a Microphone 6 Turning the Equipment Off 7
3 Turning the Data Projector on: To start the projector, press the ON button. This will power the data projector on. Please allow 30 seconds for the data projector to warm up. Using the computer located in the console: After the data projector has been successfully turned on, ensure that the computer is also powered on. It is located within the cabinet (this will be labeled and have a steady blue light emitting from the case). To project the computer image, press the button labeled COMPUTER on the AMX panel. Next, retrieve the wireless keyboard from inside the cabinet. Press any key on the wireless keyboard to activate the computer. The data projector will then project the computer image. Log on to the network using the login information provided to you by CCS or IMS. The integrated touchpad, located at the bottom of the keyboard takes the place of a regular mouse. Simply glide your finger over the touchpad to move the computer cursor.
Using your laptop with the data projector in the room: (1)First, plug your VGA cable into the female VGA (COMPUTER) port on the connector plate at the top of the equipment rack. (2)If you also require sound, then plug your cable into the AUDIO input. (3)If you need to use the Internet, plug an Ethernet cable into the Ethernet jack. 4 Once the data projector has powered on, press the LAPTOP button. If your laptop does not automatically send its video signal to the data projector, you may need to manually output the video signal. If you require assistance in doing this, call ext. 3815 from the phone inside the cabinet. Adjusting the volume: (1) Locate the amplifier in the cabinet. (2)Next, locate the left and right output dials, and adjust the volume, according to your preference, from 0 to 10. Please be considerate of people in the classroom s neighboring yours. When you are done, please turn the volume down to 2 or 3 on both the left and right output dials. Please leave all other settings as you had found them.
Blanking the image (temporarily) from the data projector: 5 With the data projector powered on, press the ON button once to blank the projected image. The red light next to the button will begin to flash. To restore the image, press the ON button once again. Using the VCR: Before beginning, make sure that the data projector has been powered on, and that the volume on the amplifier (left and right) is reduced. (1) Insert the tape into the VCR side of machine (number 1 on diagram). (2) Select the VCR button on the AMX panel. (3) Press PLAY/PAUSE (> ) to start the tape. (4) Adjust the volume on the amplifier to your desired level (page 4). (5)Press STOP( )to stop the tape, or PLAY/PAUSE (> ) in order to pause the tape. (6) To rewind or fast forward your tape you can use the remote secured to the rack or you may use the buttons located on the DVD/VCR itself (these buttons work for both DVD and VCR). (7) When you are finished using the VCR, remember to take your tape out of the machine, and turn the volume down on the left and right outputs on the amplifier.
Using the DVD player: Before beginning, make sure that the data projector has been powered on, and that the volume on the amplifier (left and right) is reduced. 6 (1) Power the DVD player ON (by pressing button 1). (2) Press the DVD Open/Close button (labeled button 2 on diagram). (3) Place the DVD in the open disc tray (labeled number 3 on diagram). (4) Press the DVD Open/Close button to close the disc tray (number 2 on diagram). (5) Select the DVD button on the AMX panel. (6) Press the PLAY/PAUSE (> ) button to start the disc. (7) Adjust the volume on the amplifier to your desired level (page 4). (8) Press the STOP ( ) button to stop the disc, or the PAUSE/PAUSE (> ) button to pause it. (9) When you are finished, remember to take your DVD out of the machine, and turn the volume down on the left and right outputs on the amplifier. Connecting a microphone: (1) Plug an XLR cable from a microphone into the XLR input on the Extron plate (labeled microphone). (2) Adjust the volume to your desired level using the left and right output dials on the amplifier (see page 4). (3) When you are finished, turn the volume down on the amplifier.
7 Turning the equipment off: (1) Turn the data projector off by selecting the off button on the AMX panel. (2) Ensure that any cables, keyboards, or mice that you may have been using have been placed back inside the cabinet. (3) Lock up the equipment rack. (4) Remember to take your key to the equipment cabinet with you! For further assistance, please call ext 3815 from the phone located in the rack.