PayMatic P2000 Installation Manual PayMatic P2000 Product Version: N/A Version of this manual: 2.1.2 2016 Inepro B.V. All rights reserved
PayMatic P2000 The most versatile payment solution Congratulations on your selection of the PayMatic. We are certain you will be pleased with your purchase of one of the finest payment solutions of the market. We want to help you to get the best result from your PayMatic and show you how to operate it. This manual contains information on how to do that; please read it carefully. Due to continuous product improvements this manual is subject to changes without notice. Your Inepro business partner is dedicated to your satisfaction and will be pleased to answer your questions and your concerns. Best wishes, Inepro BV.
PayMatic P2000 All rights reserved. No parts of this work may be reproduced in any form or by any means graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document. Version 2.1.2 created: August 2016 in Nieuw-Vennep. Publisher Inepro B.V. Managing Editor K. de Graaf Technical Editors P. Grimmerink J. van den Berg P. Blom Cover Design H. Wagenaar K. de Graaf Team Coordinator R. Groen Production Inepro B.V.
Table of Contents Introduction Open / disassemble the PayMatic Installation Notes 2 4 7 9
Directives ATTENTION!! Read this manual carefully before installing the PayMatic P2000! Mains connection Before connecting the appliance to the mains, check that the mains supply voltage corresponds to the voltage printed on the type plate of the adapter. If the mains voltage is different, consult your supplier. Guarentee No guarantee can be given if safety regulations are not followed. Security Always disconnect the power supply before handling anything inside the device. This document: Due to continuous product improvements this manual is subject to change without notice. This document describes the technical and functional operation of the PayMatic P2000. Greatest care has been taken drafting the information in this manual and it may be said that it is reliable. However, the producer is not liable for any shortcomings in the text or incompleteness of the information. Thank you for your decision to use the PayMatic P2000. Indoor User Only This device may only be used indoors. CE Conformité Europeène (Conform European Norm) This device is in conformity with the EMC directive and low-voltage directive. WEEE Directive (Waste of Electrical and Electronic Equipment) Inepro considers it important to properly take the climate into account. We therefore produce as many climate-friendly products. Your new device contains materials which can be recycled and then reused. At the end of life, specialized companies can dismantle the device, to materials which can be reused in order to recycle and reuse. For example, the materials that must be discarded will be limited to a minimum. Please take into account the rules and regulations in your area regarding the rules about disposal of packaging materials, exhausted bateries and old equipment. Thank you, Inepro BV
Introduction I Part
Introduction Introduction The PayMatic P2000 is the simplest unit of the series coin machines and is meant to be connected to any device with a timer system which goes out automatically if necessary. Upon introduction of a coin, this PayMatic emits only a normally open or a normally closed signal to activate the device connected to the coin machine. The PayMatic housing is made of crash- and scratch-resistant plastic. The mechanical slot meter accepts only one type of coin (token). This PayMatic is not equipped with a return key, return box and it has no display either due to the lack of any electronic components. Version 2.1.2-2
Open / disassemble the PayMatic II Part
Open / disassemble the PayMatic Open / disassemble the PayMatic 1. Lay the PayMatic, if possible, on its back. 2. Open the bottom lid. If the coin box is mounted on a pillar: Open and remove the padlock at the back of the pillar. Take out the cash box, remove the locking bolts fixed on the upper side of the pillar. 3. Take out the two security pins. Open the front plate under a 15 degree angle. 4. Slide the front plate down under that angle. 5. Slide the top to the back. 6. Lift the top of the case. Version 2.1.2-4
For more information use the QR code or URL to watch the YouTube instruction movie. http://www.youtube.com/watch?v=fnptfanu6c4 7) The housing can be installed by means of the 4 units M5 x 16 mm. screws, included in this delivery, when using a fastening bow, or by means of 4 screws (M4 x 40mm) when fixing the housing to the wall. For construction follow steps 1-6 in reverse. Do not forget to replace the included locking bolts (Stap 3)!! 5 - PayMatic P2000
Installation III Part
Installation Connect the wiring to the indicated positions on the terminal strip. Make sure the connection wires leave as short as possible the machine housing. Aansluitingen: Solution 1 2 Contact Usage Use the brown (1) and the green (2) cable marked on the terminal strip. Use the brown (1) and the yellow (3) Normally open cable marked on the terminal (n.o.) contact strip. Normally closed (n.c.) contact Voltage / current microswitch; 250Vac, 4A resistive / 1A inductive Switching time The switching time of the microswitch depends on two factors, the size of the inserted coin and its rate of fall. Nevertheless, with independence of these two variable factors, the activation time of the microswitch is always from 20 ms to 200 ms. The device has to be connected by authorised and prepared personnel only! 7 - PayMatic P2000
Notes IV Part
Notes This area is meant for the reader's notes: 9 - PayMatic P2000
Notes Version 2.1.2-10