PERFORMANCE SPECIFICATION SHEET INCH-POUND 0 March 200 SUPERSEDING MIL-PRF-629/2F 2 September 200 CIRCUIT BREAKERS, MAGNETIC, PANEL SEAL, TRIP-FREE, SERIES TRIP, DOUBLE POLE (0.2 TO 0 AMPERES) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-629. FIGURE. Dimensions and configurations (configuration). AMSC FSC 92
Inches mm Ltr A ---. --- 8.48 B.7.76 8.67 9.4 C.64.67 6.28 7.04 D.89.2 0.20.78 E.969 2.0 0.0.9 F.060.06.2.6 G.00.0 0.76 0.89 H..4 2.92.68 J.2 REF.74 REF 7.92 REF 9.0 REF K.499.6 8.07 9.6 L.99.26.0 6.6 M --- 2.22 --- 6.69 N.94.66.09 6.66 P.6.9 9.27 0.0 R.79.78 8.26 9.84 S.00.0 0.76 0.89 T.079 REF.4 REF 2.0 REF.8 REF U.09 REF.02 REF 0.48 REF 0. REF V.09 REF.08 REF 0.48 REF 2.06 REF NOTES:. Dimensions are in inches. 2. Metric equivalents are given for general information only.. Unless otherwise specified, tolerance is.0 (0.79 mm). 4. Lockwasher, split, No. 8 NASM8-7 or equivalent. Terminal screw, No. 8,.64-2 UNC-2A,.87.0 long, material: Brass, tin plated (ASTM B4 or equivalent). 6. Passivated - corrosion resisting steel screw, slotted head with integral O-ring, may be replaced by the NASM22-2 with cross-recessed head or equivalent. 7. Hex mounting nut.00-2 UNF-2B thread,.62.00 across flats,.20/.2 thick, brass nickel plated, SAE-AMS-QQ-N-290 nonglare or equivalent; may be replaced with MS2082-B22 or equivalent. 8. Internal tooth lockwasher,.62.00 O.D.,.0.00 I.D.,.028.00 thick, stainless steel. 9. O-ring, material: Material shall be selected to enable the O-ring to meet the performance requirements of this specification. Butadiene acrylonitrite has been successfully used in the past and should be considered for meeting the O-ring requirements of the specification. 0. Auxiliary switch terminals shall provide for soldered connections.. Physical item marking of the words LOAD and CB CONT OPEN is optional. FIGURE. Dimensions and configurations (configuration ) - Continued. 2
FIGURE 2. Dimensions and configurations (configuration 2).
Inches mm Ltr A.98 2.0 0.42.8 B.20.2 0.6.7 C.64.67 6.28 7.04 D ---. --- 8.48 E.7.76 8.67 9.4 F.060.06.2.6 G.00.0 0.76 0.89 H..4 2.92.68 J.280.0 7. 7.87 K..4 8.48 9.24 L.2.24.46 6.22 M --- 2.620 --- 66. N --- 2.26 --- 7.0 P.7.76 8.67 9.4 R.60.640.0 6.26 S.09 REF.02 REF 0.48 REF 0. REF T.09 REF.2 REF 2.4 REF.8 REF U.00.0 0.76 0.84 V.09.2 2.4.8 W.60.90 9.4 9.9 X.24.27 6.22 6.99 Y.29.9 8.6 9.2 Z.09.2 2.4.8 NOTES:. Dimensions are in inches. 2. Metric equivalents are given for general information only.. Unless otherwise specified, tolerance is.0 (0.8 mm). 4. Lockwasher, split, No. 8 NASM8-7 or equivalent. Terminal screw, No. 8,.64-2UNC-2A,.87.0 long, material: Brass, tin plated (ASTM B4 or equivalent). 6. Passivated - corrosion resisting steel screw - slotted head with integral O-ring, may be replaced by The NASM22-2 with cross-recessed head or equivalent. 7. Hex mounting nut:.00-2 UNF-2B thread,.62..00 across flats,.20/.2 thick, brass nickel plated, SAE-AMS-QQ-N-290 nonglare or equivalent; may be replaced with MS2082-B22 or equivalent. 8. Internal tooth lockwasher,.62.00 O.D.,.0.00 I.D.,.028.00 thick, stainless steel. 9. O-ring, material: Material shall be selected to enable the O-ring to meet the performance requirements of this specification. Butadiene acrylonitrite has been successfully used in the past and should be considered for meeting the O-ring requirements of the specification. 0. Auxiliary switch terminals shall provide for soldered connections.. Physical item marking of the words LOAD and CB CONT OPEN is optional. FIGURE 2. Dimensions and configurations (configuration 2) - Continued. 4
REQUIREMENTS Dimensions and configuration: See figure and figure 2. Current ratings: See table I. High inrush: Applies unless otherwise specified. / Voltage ratings: See table II. Ratings are maximum; the minimum operating voltage is limited by the internal resistance or impedance of the circuit breaker (see table I). Auxiliary contacts: Contact capacity shall be 0 amperes to 20 volts 60/400 Hz and 2 amperes resistive, ampere inductive to 0 V dc. Tripping-time delays: See table I and table II. Terminal and mounting hardware: See figure. Terminals: See figure. Solderability is applicable to auxiliary contact terminals. Actuator strength: 2 pounds. Actuator operating force: 4 pounds, maximum. Terminal strength: Applied load: 0 pounds. Applied torque: 0 inch-pounds. Interrupting capacities: 2,000 amperes at 0 V dc. 2,000 amperes at 20 V ac, 60 Hz.,00 amperes at 20 V ac, 400 Hz.,000 amperes at 240 V ac, 60 and 400 Hz. Seal: Panel seal test applies.
Part or Identifying Number (PIN): The PIN to be cataloged and stocked by the Government consists of the prefix M629/2 and four succeeding code letters as follows: /, 2/ For pole identification, see figure Two pole circuit breaker with panel seal, and auxiliary contacts. Current rating code, see table I. / { Pole Pole 2 M629/2 E K E M Voltage, frequency, and time delay { curve code, see tables I and II. / When circuit breakers without auxiliary contacts, are installed in new equipment, replacement spares should possess this feature since it is more economical for the DoD to stock one version of this item instead of two. Therefore, stock numbers should not be requested (or assigned) for this special PIN. / Special PINs for equipment manufacturers use only. Equipment manufacturers who do not require the high-inrush feature or auxiliary contacts in specific production applications may order circuit breakers without these features by modifying the prefix as follows: M629/2XXXX. Replace slash with A for items without auxiliary contacts (M629A2XXXX). Replace slash with B for items without the high-inrush feature (M629B2XXXX). Replace slash with C for items without either high-inrush feature or auxiliary contacts (M629C2XXXX). 2/ Replace slash with D for items requiring configuration 2 (M629D2XXXX). Replace slash with E for items requiring configuration 2 without auxiliary contacts (M629E2XXXX). Replace slash with F for items requiring configuration 2 without the high-inrush feature (M629F2XXXX). Replace slash with G for items requiring configuration 2 without the high-inrush feature or auxiliary contacts (M629G2XXXX). / If both poles have identical ratings, code letters will repeat for each pole. If both poles are not identical, poles and 2, respectively (see figure ) shall be coded in ascending order of the current rating code letter. If both poles have identical current ratings but different voltage, frequency, and time delay code letters, then these code letters shall be coded in ascending order. 6
TABLE I. Circuit breaker dash numbers and applicable characteristics (configuration ). Current rating Voltage Resistance Current rating Voltage Resistance Amperes Code letter frequency and tripping time delay code letter from table II or impedance ohms (max) Amperes Code letter frequency and tripping time delay code letter from table II or impedance ohms (max) 0.20 0.20 0.20 0. 0. 0. 0. 0. 0. 0.7 0.7 0.7.0.0.0.7.7.7 2. 2. 2..0.0.0 A A A B B B C C C D D D E E E F F F G G G H H H J J J 20 at dc 20 at 60 Hz 0 at 400 Hz 2 at dc 2 at 60 Hz 4 at 400 Hz 2 at dc 2 at 60 Hz 0 at 400 Hz 6 at dc 6 at 60 Hz 2 at 400 Hz at dc at 60 Hz 7 at 400 Hz 2 at dc 2 at 60 Hz 4 at 400 Hz 0.9 at dc 0.9 at 60 Hz 2 at 400 Hz. at dc. at 60 Hz.6 at 400 Hz. at dc. at 60 Hz. at 400 Hz 4.0 4.0 4.0.0.0.0 7. 7. 7. 0.0 0.0 0.0 2. 2. 2..0.0.0 20.0 20.0 20.0 2.0 2.0 2.0 0.0 0.0 0.0 K K K L L L M M M N N N P P P R R R S S S T T T U U U. at dc. at 60 Hz. at 400 Hz.08 at dc.08 at 60 Hz. at 400 Hz.0 at dc.0 at 60 Hz. at 400 Hz.02 at dc.02 at 60 Hz.04 at 400 Hz.0 at dc.0 at 60 Hz.0 at 400 Hz.0 at dc.0 at 60 Hz.02 at 400 Hz.007 at dc.007 at 60 Hz.0 at 400 Hz.006 at dc.006 at 60 Hz.007 at 400 Hz.00 at dc.00 at 60 Hz.006 at 400 Hz 7
TABLE II. Circuit breaker dash numbers and applicable characteristics (configuration 2). Current rating Voltage Resistance Current rating Voltage Resistance Amperes Code letter Amperes Code letter 0.20 0.20 0.20 0. 0. 0. 0. 0. 0. 0.7 0.7 0.7.0.0.0.7.7.7 2. 2. 2..0.0.0 A A A B B B C C C D D D E E E F F F G G G H H H J J J frequency and tripping time delay code letter from table II or impedance ohms (max) 86 at dc 42 at 60 Hz 0 at 400 Hz 26.4 at dc 26.4 at 60 Hz 60 at 400 Hz.2 at dc.2 at 60 Hz 0 at 400 Hz 6 at dc 6.6 at 60 Hz 2 at 400 Hz at dc at 60 Hz 7 at 400 Hz 2 at dc 2 at 60 Hz 4 at 400 Hz 0.9 at dc 0.9 at 60 Hz 2 at 400 Hz 0. at dc 0. at 60 Hz 0.7 at 400 Hz 0. at dc 0. at 60 Hz 0. at 400 Hz 4.0 4.0 4.0.0.0.0 7. 7. 7. 0.0 0.0 0.0 2. 2. 2..0.0.0 20.0 20.0 20.0 2.0 2.0 2.0 0.0 0.0 0.0 K K K L L L M M M N N N P P P R R R S S S T T T U U U frequency and tripping time delay code letter from table II or impedance ohms (max) at dc at 60 Hz 0. at 400 Hz 0.08 at dc 0.08 at 60 Hz 7 at 400 Hz 0.0 at dc 0.0 at 60 Hz at 400 Hz 0.02 at dc 0.02 at 60 Hz 0.04 at 400 Hz 0.06 at dc 0.0 at 60 Hz 0.0 at 400 Hz 0.02 at dc 0.0 at 60 Hz 0.02 at 400 Hz 0.007 at dc 0.007 at 60 Hz 0.0 at 400 Hz 0.006 at dc 0.006 at 60 Hz 0.009 at 400 Hz 0.00 at dc 0.00 at 60 Hz 0.006 at 400 Hz 8
9 Time delay percent rated current See footnotes at end of table IV. TABLE III. Operating voltage, frequency, and tripping-time delay delay (configuration ). / Tripping-time delay at 2 C 2 C (tripping time in seconds) 0 V dc 240 V ac, 60 Hz 240 V ac, 400 Hz K L M N P R S no trip no trip no trip no trip no trip no trip no trip 00 one hour one hour one hour one hour one hour one hour one hour 2 00 0 2. 20 0 8 0 200 400 600 800,000 20 2.6.29 2..6...29..06.0..0 20 2...6.29...6..7.09.04.6.04 60 20 4.6.06.04 6 2..4.8 2..2.0.06.6.2.0 00 60 9...04 60 20 2.20.02,800 2/ no trip no trip no trip no trip no trip no trip no trip
0 Time delay percent rated current TABLE IV. Operating voltage, frequency, and tripping-time delay (configuration ) - Continued. / Tripping-time delay at high and low temperature C (tripping time in seconds) / 0 V dc 240 V ac, 60 Hz 240 V ac, 400 Hz K L M N P R S +8 +8 +8 +8 +8 +8 no trip no trip no trip no trip no trip no trip no trip 00 one hour one hour one hour one hour one hour one hour one hour 2 00. 00. 00 00. 0 00. 00. 00 200 00. 0.0 00.0 0.0 00. 0.0 00 400 20 20 20 00 600 800 2...... / Circuit breakers shall not trip at 00 percent rated current but must trip at 2 or 0 percent of rated current. Between 00 percent and 2 or 0 percent, they may trip. antaneous is defined as less than milliseconds. 2/ Items without the high-inrush feature (for use in production only) are not subject to this requirement. High-inrush test shall be performed using one alternation which has a peak value of 800 percent of rated current. 400 Hz and dc delays shall be subjected to a 400 Hz waveform, 60 Hz delays shall be subjected to a 60 Hz waveform. / High and low test temperature tolerances are 2 C. +8.
Time delay percent TABLE V. Operating voltage, frequency, and tripping-time delay (configuration 2). / Tripping-time delay at 2 C ±2 C (tripping time in seconds) 0 V dc 240 V ac, 60 Hz 240 V ac, 400 Hz rated K L M N P R S current no trip no trip no trip no trip no trip no trip no trip 00 one hour one hour one hour one hour one hour one hour one hour 2 0 200 400 600 800,000 60 0 2 0. 7 0.6 6..2 0. 0.2 0. 0.0 20 20 2 0.8 0.2 0 2.2 0. 2 0. 0.7 0.0 70 2 2.4 2. 0.4 8.9 0.4 0.2 0.0 0.04,800 2/ no trip no trip no trip no trip no trip no trip no trip See footnotes at end of table VI. 0. 0.02 400 0 9 7 0.4 40 9..9
2 Time delay percent rated current TABLE VI. Operating voltage, frequency, and tripping-time delay (configuration 2) - Continued. / Tripping-time delay at high and low temperature C (tripping time in seconds) / 0 V dc 240 V ac, 60 Hz 240 V ac, 400 Hz K L M N P R S +8 C +8 C +8 C 800 2 0. 2.8 0. 8.4 0. / Circuit breakers shall not trip at 00 percent rated current but must trip at 2 or 0 percent of rated current. Between 00 percent and 2 or 0 percent, they may trip. antaneous is defined as less than milliseconds. 2/ High-inrush test shall be performed using one alternation, which has a peak value of 800 percent of rated current. 400 Hz and dc delays shall be subjected to a 400 Hz waveform, 60 Hz delays shall be subjected to a 60 Hz waveform. / High and low test temperature tolerances are ±2 degree Celsius. no trip no trip no trip no trip no trip no trip no trip 00 one hour one hour one hour one hour one hour one hour one hour 2 0 200 400 600 00 00 20 00 0 0.0 700 60 26 0.0 00 0 0.0 600 0 2 26 0. 00 0 0.0 00 00 00 24 +8 C +8 C +8 C +8 C 0.
Circuit breakers covered by this specification replace commercial types as specified in table III providing they have equivalent current, voltage, frequency, and time delay ratings. Circuit breakers without either auxiliary contacts or the high-inrush feature should be replaced by equivalently rated military items with both of these features. TABLE VII. Supersession and substitution data. Superseding military PIN M629/2XXXX Superseded manufacturers PIN CAGE 84 Type APGN-66 UPGN-66 IEGN-66 Reference documents. In addition to MIL-PRF-629, this document references the following: ASTM-B4 MS2082 NASM22 NASM8 SAE-AMS-QQ-N-290 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Army - CR Navy - EC Air Force - 8 DLA - CC Preparing activity: Army - CR Agent: DLA - CC Review activities: (Project 92-200-02) Army - AV, CR4, MI Navy - AS, MC, OS, SH Air Force - 9, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.daps.dla.mil.