HDX K Quick Start Guide Download Product Manual Product manuals and documentation are available online at www.barco.com/td/r000 Registration may be required; follow the instructions given on the website. IMPORTANT! Read Installation Instructions before connecting equipment to the mains power supply. Install Lens & Lens safety cable!! ONLY USE TLD+ Zoom Lenses!!. Remove the plastic cover from the Lens Holder opening.. Place the Lens Holder in unlock position. Handle towards electrical socket.. Gently insert the lens. Ensure the lens connector matches the electrical socket on the Lens Holder.. Insert the lens until the connector seats into the socket.. Secure the lens in the Lens Holder. Move the handle into the lock position.. Check if the lens touches the front plate of the Lens Holder.. Check if the lens is really secured by trying to pull the lens out of the Lens Holder.. Install the lens safety cable tightly around the lens. Keep safety cable as short as possible.. Attach lens safety cable with projector frame. Keep safety cable as short as possible. Connect power Ensure that the power is properly connected to the power input. (0-0V / 00-0V, A, 0-0Hz) R00 /0
Startup. Power on. Turn the mains switch to on ( I ). - Start up sequence starts. Backlight of the Power on/off button flashes WHITE.. Press the Power on/off button. - The backlight of the Power on/off button changes from WHITE to BLUE. - Local LCD displays a start up screen. Adjust. Adjust the lens settings by pressing the LENS button or via the direct lens keys on the RCU. Select the Greenfocus test pattern to adjust the lens.. Orientation of the unit is set as standard in table front projection mode. Change the projector set up in the ALIGNMENT > ORIENTATION menu.. For Advanced adustments like Warping, Light management, etc. see User Guide of the projector. Connect and Select source. Connect available sources to the appropriate input ports.. Select connected source: - The LED of the selected source lit up GREEN. - Image of selected input appears. --
Switch off. Press the Power on/off button for three seconds.. Wait until the after-cooling cycle is finished (up to 00 sec.). Turn the mains switch to off ( 0 ).. Unplug the power cord from the projector. s Precautions 00 s Remove the lens before transporting the projector. First switch the projector to Standby mode and wait until After Cooling is finished to switch off the main power. Ensure the projector is operating with clean filters. Do not block the ventilation in and outlets. Laser light can cause severe damage to the DMD. This damage is not covered by warranty. Local Keypad -- Menu Navigation. Menu Selection. Open Menu. Menu Back. Power On/. OSD On/. Input Selection. Shutter Open/Close. Test Patterns. 0 Lens Menu. Touch Panel. 0
RCU buttons 0 0 -- Button pressed indicator. Shutter Open. Shutter Close. Touch Panel On/. LCD On/. Lens Zoom. Lens Shift. Menu Activation. Menu Selection. 0 Menu Navigation. Input Selection. Address button. Numeric buttons. Backspace XLR connector. Dot. Macro button. Menu Back. Default button. 0 Lens Focus. Color On/. Test Patterns. Power On. Power. Stereo Jack. RCU On/.
Communication Panel WiFi antenna for wireless IP (optional) V A output Firmware update/usb backup custom settings 0/00 base-t for external control over IP and Art-Net DMX interface input DMX interface output XLR input for wired projector control 0 RS for serial communication Sync Out 0 Sync In Status lights IR receive sensor GSM antenna input (optional) Venues & Hospitality Input (V&H) SDI IN SDI IN/OUT A C B DP D HDMI HDBT HDBT Quad G SDI channel A Input DisplayPort Input Quad G SDI channel B Input HDMI Input Quad G SDI channel C Input/Output HDBaseT Input Quad G SDI channel D Input/Output HDBaseT Input Virtual & Augmented Reality Input (V&AR) (Optional) DP A -- DP B DP C DP D Quad DisplayPort channel A Input Quad DisplayPort channel C Input Quad DisplayPort channel B Input Quad DisplayPort channel D Input
Button Backlight Status Button Power button Shutter button Color status Blinking WHITE Solid WHITE Description Projector starts up (Booting) Blinking RED Projector is in Standby Error condition Blinking BLUE Projector goes to ON mode Solid BLUE Projector is ON Solid WHITE Shutter is open Solid RED Shutter is closed Projector not in power ON state -- LED Status LED Color status Description PWR (power LED) RED Projector is in Standby ORANGE GREEN LIGHT (Illumination LED) ERR (error LED) IR RED Projector is Ready Projector is on ORANGE Lamp is off No lamp inserted Lamp is on in ECO mode GREEN Lamp is on in normal mode GREEN-ORANGE Lamp is on in CLO mode No error RED toggles on/off Error ORANGE toggles on/off RED IR signal received GREEN IR signal acknowledged Support Website www.barco.com/esupport -- Projector powers up Warning Tel.: - USA + - EMEA + 0 - APAC + 00