OMNISCALE Multi-Input Scaler

Similar documents
CSC-5500 Multi-Input Scaler

EL-5500 Advanced HDMI/VGA Presentation Switch OPERATION MANUAL

CSC-5500 Multi Input Scaler

SUPERSCALE Multi-Format to HDMI Scaler

CSLUX-300 Multi-Format to HDMI Scaler

Multi-format to HDMI scaler ID#15107

CP-255ID Multi-Format to DVI Scaler

CSLUX-300I Multi-Format to HDMI Scaler

CP-255ID CV, SV, VGA and DVI to DVI Scaler / Converter OPERATION MANUAL

EL-5600 Multi Format Presentation Switch (including SDI) OPERATION MANUAL

CSLUX-300I Multi-Format to HDMI Scaler

CDPS-84HB 8 by 4 Digital Presentation Scaler

CSC K UHD+ HDMI and PC/HD to HDMI Scaler

CS-801H HD High Resolution Scaler with 3D

CP-259HN HDMI to HDMI Scaler

CS-802D HD High Resolution Scaler

CP-291N PC/HD to PC/HD Scaler

CP-255I. Multi-Format to HDMI Scaler. Operation Manual

CPLUS-V2PE 4K UHD+ HDMI to Dual HDMI Scaler with Audio De-Embedding & Test Patterns

CLUX-SDI2VS. SDI to PC/HD Scaler with Audio. Operation Manual CLUX-SDI2VS

CP-1283HDT Dual HDMI to Component & Audio Converter

8 INPUT MULTI-FORMAT SCALER SWITCH w/ VOLUME CONTROL MIRRORED HDMI/VGA OUTPUT INSTRUCTION MANUAL

CH-2538TXWPKD 4K UHD HDMI/VGA over HDBaseT Wallplate Transmitter. CH-2527RX 4K UHD HDMI over HDBaseT Receiver. Operation Manual

DCT-23 Integrated Zone Amplifier

CM-388M HDMI Repeater with Video Output

CPT-385AM PC to Video Converter Box

CV-400H. HDMI to Video Scan Converter. Operation Manual CV-400H

CM-388N HDMI to CV/SV Converter with HDMI Bypass DRAFT. Operation Manual

AU-A300 Integrated 2 Channel Zone Amplifier OPERATION MANUAL

CP-298H HDMI to HDMI Scaler Box

CH-1602TX & CH-1602RX HDMI/Audio over CAT5e/6/7 Extender with 48V PoE

CDVI-1109TXC & RXC DVI over CAT5e/6/7 with LAN/PoC/IR Extender

EGE-SCA-HDB-HVGDP HDMI/DisplayPort/VGA to HDMI Scaler with HDBaseT Output

CP-304 VGA to HDMI Video Scaler

SC-1080R Multi-Format Switcher & Scaler

CPRO-11SI HDMI 4K2K Audio Inserter

EL-7500V HDM/VGA/YUV/CV

PRO-SDIVGA. SDI Extender with PC/HD Scaler & Audio OPERATION MANUAL

CM-388M HDMI Down-Scaler with Bypass Output OPERATION MANUAL

AU-A300 Integrated 2 Channel Zone Amplifier OPERATION MANUAL

CH-506TX & RX HDBaseT HDMI over Single CAT5e/6/7 Extender

CHDBT-1H2CE 1 3 HDMI over HDMI and CAT5e/6/7 Splitter with PoE and LAN Serving

CPT-385AM PC to Video Scan Converter

3G-SDI 4 by 4 Switcher

CP-1261D PC/HD to DVI Format Converter

SY-401V PC/HD to Video Scan Converter OPERATION MANUAL

CH-304TX & RX Digital Audio over Single CAT5e/6/7 Extender

CP-1261HS PC/HD with Audio to HDMI Format Converter DRAFT. Operations Manual

CH-507TX & RX HDMI to CAT5e/6 with LAN/IR/RS-232

SY-HDVGA-4K22 PC/HDMI

DCT-3 Digital to Analog Stereo Audio Converter

CH-507TXBD & RXBD HDMI to CAT5e/6 with LAN/IR/RS-232/ Bidirectional PoE DRAFT. Operation Manual

CMSDI G-SDI Matrix

CH-304TX & RX Digital Audio Extender over Single CAT5/6

CH-507TX & RX HDMI to CAT5e/6 with LAN/IR/RS-232

CH-506TX & RX CH-506TXL & RXL HDMI/IR/RS-232 over Single CAT5e/CAT6 Extender

CH-526RX HDMI Splitter with Audio over CAT5e/6/7 Receiver

EGE-IR Bi-directional Infrared Matrix

PU-515PL-KIT HDBaseT LITE Extender Kit with PoE & 2-way IR (up to 60m) OPERATION MANUAL

CLUX-DVI2SDIA. DVI to 3G SDI Converter. Operation Manual

CM-398 CV/SV to PC Converter Box

PRO-3GSDIHDMI. 3G-SDI Extender with HDMI Scaler OPERATION MANUAL

CP-1262HST. HDMI to PC/Component Converter with Audio Box. Operation Manual CP-1262HST

CM-388MN2 HDMI Repeater with SD Video Output

CPLUS-V11SE8 UHD 4K 6G with HDCP2.2 LPCM 7.1 Audio Extractor

CH-2507TX & CH-2507RX HDMI to CAT5e/6/7 Transmitter and Receiver with LAN/IR/RS-232/PoE

AU-11CA-4K Embed Audio onto HDMI (4K Resolution support)

Globalmediapro SMR-650

CMLUX-4H4CAT. 4 by 4 HDMI V1.3 over CAT 6 Matrix with IR Return Control. Operation Manual CMLUX-4H4CAT

CH-507TX & RX HDMI over CAT5e/6/7 Transmitter and Receiver

SCHD24K 4K UHD + HDMI to HDMI Scaler

CP-1262HE. HDMI to PC/Component Converter with Audio Box. Operation Manual CP-1262HE

CHQV-2H. HDMI to HDMI Scaler Box. Operation Manual CHQV-2H

CSO-T2. Instant HQV HD Scaler Box. Operation Manual CSO-T2

CPLUS-V4T 4K UHD HDMI Splitter

CLUX-H2SDIA. HDMI to 3G SDI Converter. Operation Manual

CSO-T2. Instant HQV HD Scaler Box. Operation Manual CSO-T2

PU-607BDWP-RX HDMI over Single CAT5e/6/7 HDBaseT - Bi-Directional PoE Wallplate Receiver (full 5Play & Single LAN up to 100m) OPERATION MANUAL

AU-11CD-4K De-embed Audio from HDMI (4K Resolution support)

XHDMI. HDMI to HDMI Scaler Box. Operation Manual

DCT-2 Digital Audio Converter with Dual Outputs

CM-398M CV/SV to PC/HD Converter

CWHDI-TX2 & RX2 Wireless Multi-Format input Transmitter to HDMI Receiver Box

COH-Tx & COH-Rx. HDMI to Optical Transmitter and Receiver. Operation Manual. COH-Tx & COH-Rx

PU-444HBTE 4 x 8 HDMI / HDBaseT Matrix (4 x HDBaseT & 4 x HDMI Outputs, 5Play inc. PoE & Single LAN, up to 100m) OPERATION MANUAL

PRO-SDI44/84/124/164. 4x4/8x4/12x4/16x4 3G-SDI Matrix Switchers OPERATION MANUAL

PU-4H4HBT 4 x 4 HDMI HDBaseT Matrix (inc. PoE) OPERATIONS MANUAL

DVI/PC/HD to DVI/PC Scaler - ID# 15320

CH-514TXL/RXL HDBaseT TM Lite HDMI over Single CAT5e/6/7 Extender

CPLUS-11HB 4K2K HDMI 6G Pattern Generator with Audio Bridge

Operation Manual DCT-9

CH-513TXL/RXL HDMI to CAT5e/6 Extender

Instruction Manual. 1T-VS-668 Universal Presentation Switcher/Scaler

CH-U330TX & CH-U330RX 4K UHD Multi-Function Extender with Video over IP and KVM

CLUX-SDI2HC. 3G SDI Extender with HDMI Converter. Operation Manual CLUX-SDI2HC

PU-607BD-TX HDMI over Single CAT5e/6/7 HDBaseT Bi-directional PoE Transmitter

HDMI Over CAT5 Receiver at 50 Meters

CM-398H. CV/SV to HDMI Converter with Audio Input. Operation Manual

CDA-SDI400. 3G-SDI 1 by 4 Splitter

CLUX-H2SDIA HDMI to 3G SDI Converter OPERATIONS MANUAL

Transcription:

OMNISCALE Multi-Input Scaler Operation Manual

DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. SPATZ assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. SPATZ assumes no responsibility for any inaccuracies that may be contained in this document. SPATZ also makes no commitment to update or to keep current the information contained in this document. SPATZ reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without express written permission and consent from SPATZ. Copyright 2013 by SPATZ All Rights Reserved. TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE 27/06/13 Preliminary Release

CONTENTS 1. Introduction... 1 2. Applications... 1 3. Package Contents... 1 4. System Requirements... 1 5. Features... 1 6. Operation Controls and Functions... 2 6.1 Front Panel... 2 6.2 Rear Panel... 3 6.3 Remote Control... 4 6.4 RS-232 Protocols... 5 6.5 RS-232 and Telnet Commands... 6 6.6 OSD MENU... 9 6.7 Telnet Control... 12 6.8 Web GUI Control... 14 7. Connection and Installation... 15 8. Specifications... 16 8.1 Support I/O Resolution... 17

1. INTRODUCTION The Multi-Input Scaler has CV, Component, PC, and HDMI inputs and can scale the signal into HDMI, VGA with audio output ports. This high performance Multi-Input Scaler supports HDMI output resolution up to 1080p /WUXGA and Analog Digital Conversion (ADC) & Digital Analog Conversion (DAC) allowing a wide range of AV signal to be converted to a High-definition signal. OSD, IR-Remote, RS-232, Telnet, Web GUI and on-panel controls make this Multi-Input Scaler very user friendly. 2. APPLICATIONS Lecture hall Meeting room Conference hall 3. PACKAGE CONTENTS Multi-Input Scaler Remote Control (CR-122) 2 x AAA Batteries IR Extender Cable D-Sub to RCA adaptor cable Power Adaptor Operation Manual 4. SYSTEM REQUIREMENTS Input source equipments such as Blu-ray/DVD players or PC/NB, output display and amplifier or speakers. 5. FEATURES Supports multi-av inputs e.g. HDMI or PC/HD outputs Supports EDID and HDCP Supports 3D de-interlace, noise reduction and 3D Comb filter Supports frame rate conversion Supports RS-232, Telnet, Web GUI & IR Controls Support output timing hot keys switching HDMI compatible with DVI

6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel POWER CV COMP PC 1 PC 2 PC 3 HDMI 1 HDMI 2 HDMI 3 MENU 720P - + ENTER XGA 1 POWER button & LED: 2 IR: Press this button to switch ON or set the device to standby mode. Once the device is connected with power supply and the power toggle is switched to ON the LED will illuminate and the device will switch ON automatically. The unit will remember last setting when repowered. This IR window receives only the IR signal from the remote control included in the package. 3 INPUT button and LEDs: Press this button sequentially to switch in between the input sources rotationally. LED will illuminate accordingly to the selected input source. 4 MENU: Press this button to enter into the OSD menu. 5 -/+: Press these buttons to scroll down and up in the OSD selection. 6 ENTER: Press this button to confirm the selection. Press this button together with [+] button to switch output to XGA instantly or with [-] button to switch output to 720p instantly.

6.2 Rear Panel IR IN SERVICE R L RS232 COAX AUDIO AUDIO CONTROL POWER HDMI 1 HDMI 2 PC/HD HDMI 1 HDMI 2 HDMI 3 PC 1 PC 2 PC 3 Cr/Pr Cb/Pb Y R L CV DC 5V 1 IR IN: Plug in the IR extender cable for IR signal receiving from the included remote control. 2 SERVICE: Reserved for firmware upgrades 3 RS-232: Connect with PC/Laptop and use RS-232 command to control the device. 4 OUTPUT: HDMI 1 & 2: Connect to HDMI display or amplifier for video and audio display. COAX: Connect to active speaker or amplifier for audio output in digital format. AUDIO: Connect to active speaker or amplifier for audio output in stereo format. PC/HD: Connect to monitor/display for video output display. For HD output, use D-Sub 9-pin to 3 RCA adaptor cable for output HD timing from 480p~1080p. 5 INPUT: NOTE: This output is disabled with HDCP encrypted sources. HDMI 1~3: Connect to HDMI source equipments such as Blu-ray/ DVD player for both video and audio signal sending. PC 1~3: Connect with PC/Laptop source equipments for video signal input with D-Sub 15-pin cable. Audio L/R: Connect to source equipment s L/R output corresponding to the input port below with 3.5Ø phone jack. The priority audio input of HDMI is from HDMI, only when HDMI input has no audio signal the L/R audio will be inserted into. YCbCr/YPbPr + L/R: Connect to source equipment such as video/

DVD player for both video and audio signal sending. CV + L/R: Connect to source equipment such as video/dvd player for both video and audio signal sending. 6 CONTROL: This port is the link for Telnet or Web GUI controls, connect to an active Ethernet link with an RJ45 terminated cable (for further details, please refer to section 6.7 & 6.8. 7 POWER: Switch this power toggle to turn ON and activate the device or to turn OFF and shut it down. 8 DC 5V: Plug the power adaptor included in the package and connect it to the AC wall outlet for power supply. 6.3 Remote Control 1 POWER: Press this button to switch ON or set the device to standby mode. The device must connect with power supply and the power toggle must switch to ON. 2 HDMI1~3/PC1~3/CV/COMP: Press these hot keys to switch input source instantly. 3 EXIT: Press this button to exit the menu or the current selection under OSD. 4 MENU: Press this button to enter into the OSD menu. 5 OK & : Press [OK] to confirm the selection or press the arrow buttons to scroll in the OSD selections. 6 RESET: Press this button to set the device back into the factory default setting. 7 AUTO ADJUST: Press this button when output image is not fitting the display's screen perfectly. The device will auto adjust the image to full screen. HDMI1 RESET HDMI2 POWER HDMI3 PC1 PC2 PC3 CV EXIT OK CR-122 COMP MENU AUTO ADJUST

8 : Press right and left buttons to increase and decrease the volume when outside of OSD menu selection. 6.4 RS-232 Protocols PIN OMNISCALE Assignment 1 NC 2 Tx 3 Rx 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC Baud Rate: 19200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1 Remote Control PIN Assignment 1 NC 2 Rx 3 Tx 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC

6.5 RS-232 and Telnet Commands?: Show command list under Telnet. Command Description Contents S POWER 0/1 Power ON or OFF OFF(0) / ON(1) R POWER Request power status S SOURCE 1~8 Select input source HDMI1(1) / HDMI2(2) / R SOURCE Inquire input source HDMI3 (3) / YPBPR(4) / VIDEO(5) / PC(6) / PC2(7) / PC3(8) S OUTPUT 0~21 Select output timing*1 640*480(0)/800*600(1)/ R OUTPUT Inquire output timing 1024*768(2)/1280*768(3)/ 1360*768(4)/1280*720(5)/ 1280*800(6)/1280*1024(7)/ 1440*900(8)/1400*1050(9)/ 1680*1050(10)/ 1600*1200(11)1920*1080(12) / 1920*1200(13)/ 480p(14)/720p 60(15)/ 1080i 60(16)/ 1080p 60(17)/ 576p(18)/720p 50(19)/ 1080i 50(20)/ 1080p 50(21) S SIZE 0~6 Select output size OVERSCAN(0) / FULL(1) / R SIZE Inquire output size FOLLOW INPUT(2) / PAN SCAN(3)/LETTER BOX(4) / S INPUTHDCP 0/1 Select HDCP setting ON(0) / OFF(1) R INPUTHDCP Inquire HDCP setting ON(0) / OFF(1) S CONTRAST 0~60 R CONTRAST Contrast Setting Inquire contrast setting S BRIGHTNESS 0~60 Brightness setting R BRIGHTNESS S HUE 0~60 R HUE Inquire brightness setting Hue setting Inquire hue setting S SATURATION 0~60 Saturation setting R SATURATION S SHARPNESS 0~30 Inquire saturation setting Sharpness setting

R SHARPNESS Inquire sharpness setting S NR 0~3 Noise reduction setting OFF(0) / LOW (1) / MIDDLE(2) / HIGH(3) R NR Inquire noise reduction setting S VOLUME 0~100 R VOLUME Volume Setting Inquire Volume setting S AUDIODELAY 0~3 Audio delay setting OFF(0) / 40ms (1) / 110ms(2) / 150ms(3) R AUDIODELAY Inquire audio delay setting S AUDIOMUTE 0/1 Audio mute setting ON(0) / MUTE(1) R AUDIOMUTE Inquire audio mute setting S HDMIAUDIO 0/1 Change active input AUTO(0) / EXT.(1) R HDMIAUDIO Inquire Audio setting Select HDMI input first S KEY LOCK 0/1 Key lock setting ENABLE(0) / DISABLE(1) R KEY LOCK S FREERUNCOLOR 0/1 R FREERUNCOLOR S RESET 1 Inquire key lock setting Free run color setting BLACK (0) / BLUE (1) Inquire free run color setting Pre-reset S autoscan 0/1 Set to Autoscan inputs ON(0) / OFF(1)

PORT (0~8) Set active port when repower on ST FW vers. & source info. 0.00~x.xx LAST MEMORY(0) / HDMI(1) / HDMI2(2) / HDMI3(3) / YPBPR(4) / VIDEO (5) / PC(6) / PC2(7) / PC3(8) SOURCE: HDMI ~ PC3 PORT ON:LAST ~ PC3 VOL + Volume up and down VOLUME * IS SET VOL - QUIT EXIT (Telnet only) * 1 Resolution 0~13 are RGB encoded and resolution 14~21 are YUV encoded. All command will be not executed unless followed with a carriage return + LF and commands are case-insensitive.

6.6 OSD MENU 1 st Layer 2 nd Layer 3 rd Layer 4 th Layer 640x480 60 800x600 60 1024x768 60 1280x768 60 1360x768 60 1280x720 60 1280x800 60 1280x1024 60 1440x900 60 1400x1050 60 OUTPUT 1680x1050 60 1600x1200 60 1920x1080 60 1920x1200 60 1280X720P 60 1920X1080I 60 1920X1080P 60 720X576P 50 1280X720P 50 1920X1080I 50 1920X1080P 50 DISPLAY OVER SCAN FULL FOLLOW INPUT SIZE PAN SCAN LETTER BOX UNDER 2 UNDER 1 OFF MODE INFO INFO ON INPUT HDCP (HDMI mode only) PC (PC mode only) OFF ON AUTO SETUP H_POSITION V_POSITION PHASE CLOCK WXGA/XGA RESET XGA WXGA

COLOR AUDIO SETUP CONTRAST 0~60 (30) BRIGHTNESS 0~60 (30) COLOR R 0~1023 (512) G 0~1023 (512) B 0~1023 (512) R OFFSET 0~1023 (512) G OFFSET 0~1023 (512) B OFFSET 0~1023 (512) HUE 0~60 (30) SATURATION 0~60 (30) SHARPNESS 0~30 (0) NR. OFF LOW MIDDLE HIGH VOLUME 0~100 (100) OFF 40mS DELAY 110mS 150mS SOUND SOURCE(HDMI mode only)*1 FACTORY RESET*2 KEY LOCK POWER SAVE IP MODE SET STATIC IP FREERUN COLOR ON MUTE AUTO EXT. OFF ON OFF ON DHCP STATIC IP ADDRESS SUBNET MASK Def. Getway BLACK / BLUE 0.0.0.0.~255.255. 255.255*3 0.0.0.0.~255.255. 255.255*4 0.0.0.0.~255.255. 255.255*5 AUTOSCAN OFF ON

INFORMATION INPUT OUTPUT REVISION IP ADDRESS Factory default setting. *1 When Audio Source is set on Auto, the device will select audio signal according to input source. If input signal is with HDMI, the device will use embedded audio and if input signal is DVI, the device will use external L/R audio. When Audio Source is set on EXT, the device will use external L/R audio. *2 Factory reset under OSD only reset part of settings to reset completely please use the reset button from the remote control. *3 192.168.0.1 (Default Setting) *4 255.255.255.0 (Default Setting) *5 192.168.0.254 (Default Setting)

6.7 Telnet Control Before attempting to use the telnet control, please ensure that both the Scaler (via the 'LAN port) and the PC/Laptop are connected to the active networks. To access the telnet control in Windows 7, click on the "Start" menu and type "cmd" in the Search field then press enter. Under Windows XP go to the "Start" menu and click on "Run", type "cmd" with then press enter. Under Mac OS X, go to Go Applica tions Utilities Terminal See below for reference. Once in the command line interface (CLI) type "telnet", the IP address of the unit you wish to control. Note: The IP address can be found from OSD menu under Information.

After typing IP adress you should be connected To verify Type "?" to list all the commands. Note: All command will not be executed unless followed by a carriage return. Commands are case-insensitive. If the IP is changed then the IP Address required for Telnet access will also needs to be change accordingly.

6.8 Web GUI Control On a PC/Laptop that is connected to an active network as the Scaler, open a web browser and type device's IP address on the web address entry bar. The browser will bring up the control page of Scaler.

IR IN OUTPUT SERVICE RS232 COAX AUDIO HDMI 1 HDMI 2 PC/HD HDMI 1 HDMI 2 HDMI 3 PC 1 PC 2 PC 3 Cr/Pr Cb/Pb AUDIO R L INPUT CONTROL R L CV POWER DC 5V Y 7. CONNECTION AND INSTALLATION Wireless Router(with Internet Connection) 3m 7m 3m 60 PC/NB DVI to HDMI source AVR with Coaxial Input Smartphone or Tablet Component with Stereo Audio from DVD Player Monitor/Display Composite video with Stereo Audio from DVD Player AVR TV or Monitor PC/ NB

8. SPECIFICATIONS Input Ports 1 x Component with L/R, 1 x Composite with L/R, 3 x VGA, 3 x HDMI, 6 x Audio L/R (3.5mm phone jack), 1 x USB (service only), 1 x IR Extender, 1 x RS-232 (Control Only) Output Ports 2 x HDMI, 1 x PC/HD, 1 x Coaxial, 1 x L/R Supports Input Resolution Up to WUXGA(RB) & 1080p Supports Output Resolution Up to WUXGA(RB) & 1080p Power Supply 5V/3A DC (US/EU standards, CE/FCC/ UL certified) Dimensions (mm) 432 (W) x 183 (D) x 47 (H) Weight(g) 2140 Chassis Material Metal Silkscreen Color Black Operating Temperature 0 C ~ 40 C / 32 F ~ 104 F Storage Temperature -20 C ~ 60 C / -4 F ~ 140 F Relative Humidity 20 ~ 90% RH (non-condensing) Power Consumption(W) 11

Resolution Input CV Component PC HDMI NTSC/PAL V 480i/576i V V 480p/576p V V 720p@50/60Hz V V 1080i@50/60Hz V V 1080p@50/60Hz V V VGA@60/72/75Hz V V SVGA@56/60/72/75Hz V V XGA@60/70/75Hz V V SXGA@60/75Hz V V UXGA@60Hz V V 1280x800@60Hz V V 1680x1050RB@60Hz V V 1920x1080@60Hz V V 1920x1200@60HzRB V V Resolution Output PC/HD HDMI 480p/576p V (HD) V 720p@50/60Hz V (HD) V 1080i@50/60Hz V (HD) V 1080p@50/60Hz V (HD) V VGA@60Hz V V SVGA@60Hz V V XGA@60Hz V V

SXGA@60Hz V V UXGA@60Hz V V 1280x768@60Hz V V 1280x800@60Hz V V 1360x768@60Hz V V 1400x1050@60Hz V V 1440x900@60Hz V V 1680x1050@60Hz V V 1920x1200@60Hz(RB) V V