DVD MARKER RETURN DIS A.TRK C.RE ZERO RETURN UP VOL DVD ER VIDEO CATE ORDER USER'S GUIDE For model: HR-XVCUJ Hi-Fi VCR DVD 0 TIMER /VCR /VCR CH + /VCR VCR/DVD/ For Customer Use: Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No. LPT0708-00A
Dear Customer, Thank you for purchasing the JVC DVD player video cassette recorder. Before use, please read the safety information and precautions to ensure safe use of your new DVD/VCR. CAUTIONS WARNING: WARNING: DANGEROUS VOLTAGE INSIDE TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. The /l button does not completely shut off mains power from the unit, but switches operating current on and off. shows electrical power standby and l shows ON. This unit is produced to comply with Standard IEC 60065. SYSTEM: This set operates on voltage of AC 0 0V~, 50/60 Hz with automatic switching. CAUTION When you are not using the DVD/VCR for a long period of time, it is recommended that you disconnect the power cord from the AC outlet. Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the AC outlet prior to connecting or disconnecting any signal lead or aerial. Changes or modifications not approved by JVC could void user s authority to operate the equipment. Cassettes marked VHS (or S-VHS ) can be used with this DVD/VCR. However, S-VHS recording is not possible with this model. This model is equipped with SQPB (S-VHS QUASI BACK) that makes it possible to play back S-VHS recordings with regular VHS resolution. HQ VHS is compatible with existing VHS equipment. Use the conversion plug (provided) depending on the type of your AC WALL outlet. The rating plate and safety caution are on the rear of the unit. IMPORTANT: It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (0 cm or more on both sides, on top and at the rear). When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly. Failure to heed the following precautions may result in damage to the DVD/VCR, Remote or video cassette.. DO NOT place the DVD/VCR...... in an environment prone to extreme temperatures or humidity.... in direct sunlight.... in a dusty environment.... in an environment where strong magnetic fields are generated.... on a surface that is unstable or subject to vibration.. DO NOT block the DVD/VCR s ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.). DO NOT place heavy objects on the DVD/VCR or Remote.. DO NOT place anything which might spill on top of the DVD/VCR or Remote. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.) 5. DO NOT expose the apparatus to dripping or splashing. 6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit. 7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus. 8. AVOID violent shocks to the DVD/VCR during transport. MOISTURE CONDENSATION Moisture in the air will condense on the DVD/VCR when you move it from a cold place to a warm place, or under extremely humid conditions just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the DVD/VCR s power turned on for a few hours to let the moisture dry. How to use the Remote Before use, insert two AAA size batteries into the Remote with the polarity ( and ) matched correctly as indicated on the battery compartment or on the lid. Point the Remote toward the remote sensor on the target component. The maximum operating distance of the remote control is about 5 m. NOTE: If the Remote does not work properly, remove its batteries, wait for a few seconds, replace the batteries and then try again. Video heads cleaning The heads get dirty in the following cases: in an environment prone to extreme temperature or humidity. in a dusty environment flaw, dirt or mold on video tapes continuous usage for a long time Use a dry cleaning cassette TCL- when: Rough, poor picture appears while a tape is played back. The picture is unclear or no picture appears. Important Warning CAUTION: A DVD/VCR IS A CLASS LASER PRODUCT. HOWEVER THIS DVD/VCR USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DITED. BE SURE TO OPERATE THE ER CORTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE DVD/VCR. CLASS LASER PRODUCT WHEN THIS DVD/VCR IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS DVD/VCR. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION: THIS DIGITAL VIDEO ER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT A JVC AUTHORIZED SERVICE CENTER. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights owners. Reverse engineering or disassembly is prohibited. * Manufactured under license from Dolby Laboratories. Dolby and the double-d symbol are trademarks of Dolby Laboratories. Confidential unpublished works. 99-997 Dolby Laboratories, Inc. All rights reserved. * DTS and DTS Digital Out are trademarks of Digital Theater Systems, Inc. * Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and the circle - in - square device are trademarks owned by Desper Products,Inc. * Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the rights of copyright owners and be contrary to copyright laws. 5
Features DVD/CD Player/Video Cassette Recorder DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher than Super VHS. Audio quality is higher than audio CD. The DVD ER can play back video CDs and audio CDs. High Quality Picture - More than 500 lines(vcr mode: 0 lines) of Horizontal Resolution. It exceeds Super VHS (00 lines) or Laser Disc (0 lines) in resolution. VCR Section Stereo/SAP Reception - This VCR is designed to receive stereo and separate audio program (SAP) broadcasts where available. SQPB - Tapes recorded in the S-VHS system can be played back simply on this VCR. Video Heads - Provides optimal picture quality for special effects playback. 9µm HEAD - For superior picture quality even in EP mode, 9micron width technology helps to avoid crosstalk and boost EP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated. Hi-Fi Stereo Sound - With a frequency response of 0 to 0,000 Hz and a dynamic range of better than 90dB, this VCR provides a level of excellence that rivals compact discs. Instant Timer Recording (ITR) - Simply by pressing the and buttons, the VCR can be programmed for up to 5 hours of recording with an immediate start. Skip Search - When the button is pressed during playback, the VCR will automatically search forward in 0 seconds increments to a maximum of minutes with each press of the button, and then return to normal playback. DVD Section Compatible with a wide range of DVD audio outputs Digital Audio Jack (Optical or Coaxial): When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of being in a movie theater or a concert hall. Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unit to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format can be enjoyed. However, audio will not be output from the analog audio output jacks. The MPEG audio of DVD discs recorded in this format can be enjoyed. The Linear PCM sound of a 8 khz/6 bit through 96 khz/0 bit exceeds audio CD sound. Surround audio - This DVD equipped with a SPATIALIZER -D STEREO. It can produce the effect of being in a cinema or a concert hall. Multi-Language - Since this DVD matches with language-subtitles/-soundtracks, you can enjoy selecting a favorite one. (You can not select the language that is not recorded on the disc.) Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you can change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.) Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points. Program/Random Playback (CD) - You can play back tracks in programmed or random-selected sequences. Zoom - You can zoom in on the selected subject on the screen during playback. Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc. Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating. 6
Contents Before using your unit Important safeguards... Power Source... 5 Features... 6 Contents... 7 Parts and functions... 8 Display... 9 Remote control... 0 Basic connections... CA (CABLE ) connections... Playback Connection... 6 Setting up the VCR section Setting the Video Channel... 8 Setting the language... 8 Tuner Setting... 9 To ADD/DELETE channels... 0 Noise elimination... 0 Auto clock setting... Manual clock setting... Loading and Unloading a Cassette Tape... Tape Playback operation Cassette tape Playback... 5 Special playback... 6 ZERO RETURN function... 7 Video Index Search system... 7 Recording Recording a program... 8 Instant Timer Recording (ITR)... 0 Timer Recording... Advanced Function of VCR section Stereo Recording and Playback... Separate Audio Program (SAP)... Duplicating a video tape... Duplicating a disc material onto a video tape... Disc Playback operation Disc... 5 Setting setup language... 6 Playback procedure... 7 Special playback... 8 Zooming... 9 Locating Desired Scene... 9 Repeat playback... 0 Program playback (CD)... Random playback (CD)... MP Playback... Marking Desired Scenes... Changing soundtrack language... Subtitles... Changing angles... 5 Title selection... 5 DVD menu... 5 Advanced Function of DVD section Parental control... 6 Temporary disabling of rating level by DVD disc... 7 Setting menu language... 8 Setting subtitle language... 9 Setting audio soundtrack language... 50 Setting surround sound... 50 Setting the aspect ratio of screen... 5 Setting on Screen display... 5 Status display of Disc... 5 Language Code List... 5 Additional information Problems and troubleshooting... 5 Video head cleaning... 55 Specifications... back cover 7
Parts and functions Front VCR/DVD mode selector button Cassette Loading Slot EJECT button button button button Disc tray VIDEO (M) L - AUDIO - R VCR CH EJECT DVD VCR/DVD button AUDIO (L/R)/ VIDEO IN jacks Remote sensor DVD indicator CHANNEL +/ buttons (Rewind) button button VCR indicator (Fast Forward) button Rear AC power cord DVD OPTICAL DIGITAL AUDIO OUT jack DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT OPTICAL COAXIAL L R Y PB/CB PR/CR VIDEO L AUDIO R CH. IN ( ANT. ) OUT ( ) RF IN jack RF OUT jack DVD COAXIAL DIGITAL AUDIO OUT jack DVD AUDIO (L/R) OUT jacks DVD S-VIDEO OUT jack / Channel Selector Switch DVD/VCR common AUDIO (L/R)/VIDEO OUT jacks DVD COMPONENT OUT jacks 8
Display Display window 5 6 0 9 8 7 No. Display Description 5 6 7 8 9 0 VCR DVD CD PM 0 : 00 0 : 00 C00 C06 L TRK VCR mode Playback (lights) / Auto resume (flashes) Still picture DVD disc is inserted. CD is inserted. Display for afternoon (lights out in the morning) Clock display (colon[ : ] flashes) Counter display by hour/minute at VCR/DVD / by minute/second at CD Track number display for CD channel display for VCR CA channel display External input display Timer recording display Video tape is in the unit Track display for CD Normal recording display (flashes during Instant Timer Recording - ITR) Explanation for On-Screen-Symbol: Playback Stop Still picture Frame advanced playback Forward slowmotion Fast Forward playback A B Review playback Skip chapter to forward direction Skip chapter to reverse direction Open or Close the tray Auto resume Direction button s mark repeat Subtitle language Soundtrack language Angle Zoom Parental level locked Parental level unlocked Screen size: Normal Screen size: PAN SCAN Screen size: WIDE Shows Prohibited act Output sound for Video-CD Note: Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed. 9
Remote control JVC Remote Control This Remote can control some functions (, NUMBER(0-9),, VOL +/, CH +/ and ENTER) of a remote controllable JVC by slide / VCR/DVD switch to. NOTE: It s not possible to operate a unit not equipped with a remote sensor. This Remote can control a JVC only. When you operate the VCR or DVD, the /VCR/DVD switch must be slided to VCR/DVD again. Otherwise the DVD/ VCR may not operate properly. Since this unit is combined type of DVD and VCR, the remote code of DVD is individual. So please note that the DVDkeys on the RCU of the other JVC EIVER/ is not effective for this unit. 0 VCR DVD DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN SUB TITLE ANGLE MODE 0 TIMER /VCR UP /VCR VCR/DVD/ VOL Page /VCR/DVD switch Switch to operate or VCR or DVD 8,6 Power on/off 8 DVD Display menu of DVD software 5 MARKER Index for DVD RETURN Remove DVD set up menu 7 Open or Close the tray 7 DIS Change the front Display mode 7 A.TRK Digital AUTO TRACKING 6 SUB TITLE Set Subtitle of a DVD disc C. RE Reset the counter to 00:00 7 ANGLE Change playback angle of a DVD disc 5 ZERO RETURN Stop the tape when the counter reaches 00:00 7 MODE Locating desired scene 9 Sets the tape speed for recording 8,0 MODE Select playback mode 0, ZOOM Zoom (for DVD playback) 9 TITLE Select title of a DVD disc 5 REPEAT Repeat playback between A and B (DVD/CD) 0 0-9 Direct channel selection of 0,8 Input setting 9, Enter a password 6,7 TIMER Set the unit to start recording at a preset time., /VCR Switches between and VCR 8,9 Turn the connected on or off 0 Switch the connected to external mode 0 VOL +/ Adjust the connected s volume 0 Rewind/Review playback 5,6,8 Playback 5,7 Fast Forward/Forward search playback 5,6,8 Recording 8,0, Stop 5,7 Still picture/recording pause on/off 6,9,,8 / Skip chapter to forward or reverse direction 8 INDEX / Search for the INDEX mark of a tape 7 /VCR CH +/ Select channel of the connected or VCR 0,8,0, / Cursor buttons /+ Setting buttons, Manual tracking buttons in playback mode 6 / Cursor buttons - To move Up in the VCR menu you press the. To move Down in the VCR menu you press the. ENTER Enter information in the menu Select option in the menu UP Display menu of setup 8,9,6,8-5 Delete Timer program Cancel input data in the setting mode,,9, Display VCR or DVD operation status 9,5 Switches sound between mono, stereo and SAP Change sound track language of DVD Slowmotion playback 6,8 Skip the unwanted short material of a tape 6
Remote control Inserting Batteries Open the battery compart- Install two "AA" batteries (supplied), ment cover in the direction of the arrow. paying attention to the polarity diagram in the battery compartment. Replace the compartment cover. Battery precautions The precautions below should be followed when using batteries in this device:.use only the size and type of batteries specified.. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the end first.. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones..if the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer s directions.) Remote control basics Press to turn the DVD/VCR on or off. Make sure /VCR/DVD switch is set to VCR/DVD. Tap VCR CH + or VCR CH to move through the channels one channel at a time. The VCR CH +/ and +/ are also used to navigate on-screen menu system. You can directly access specific channels using Number keys pad. Each press of VCR or DVD, switches the screen between the VCR screen (VCR mode) and the DVD screen (DVD mode). Operation Aim the remote control at the remote sensor and press control buttons to operate. Operate the remote control within 0 angle on either side of the remote sensor, up to a distance of Approx. 5 meters. Approx. 5 meters Change the custom code for remote control If you operate this DVD/VCR with another JVC s VCR simultaneously arranging them side by side, the both recorders will react to this remote control. In this case, you can change the remote control and DVD/VCR to other frequency ( ). Then you can operate only this DVD/VCR with this changed remote control. When you purchased, the DVD/VCR and remote control have been set to the frequency-. Example: Change frequency to Remote control: While holding VCR, press (code: b) of Number keys. (in case of code: A, press ) VCR DVD DVD MARKER RETURN 0 TIMER /VCR VOL DVD/VCR: In the off mode, press and hold for more than 5 seconds. b will appear on the display and then disappear after approx. seconds. NOTE: If the remote control has been set to b, the DVD/VCR also must be set to b. Otherwise, the DVD/VCR can not be operated with this remote control. To reset to A, repeat above procedure. However press instead of. DVD
Basic connections If you are using an antenna system, follow these instructions. If you are a cable (CA) subscriber,skip ahead to page for the proper connections. ANTENNA TO DVD/VCR CONNECTION The DVD/VCR must be connected "between" the antenna and the. First, disconnect the antenna from the and connect it to the DVD/VCR. Then connect the DVD/VCR to the. Below are common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram. Combination VHF/UHF Antenna with 75 ohm Coaxial Cable DVD/VCR 75 ohm Coaxial Cable IN (ANT.) OUT () Combination VHF/UHF Antenna with 00 ohm Twin Lead (Flat) Wire DVD/VCR Matching Transformer 00 ohm Input 75 ohm output (not supplied) IN (ANT.) OUT () 00 ohm Twin Lead (Flat) Wire Separate VHF and UHF Antennas VHF UHF 00 ohm Twin Lead (Flat) Wire Combiner 75/00 ohm Inputs 75 ohm output (not supplied) DVD/VCR IN (ANT.) 75 ohm Coaxial Cable OUT () NOTES: A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to the DVD/VCR properly. For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type antenna is required. If you are not sure about the connection, please refer to qualified service personnel. NOTE: If both VHF and UHF antennas have 00 ohm twin lead (flat) wires, use a combiner having two 00 ohm inputs and one 75 ohm output.
DVD/VCR TO CONNECTION Basic connections After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the. Below are common methods of connecting your DVD/VCR to a. Find the type of you are using and follow the connection diagram. This DVD/VCR has a single 75 ohm output for connection to a. If your has separate VHF and UHF antenna inputs (numbers and below), use a splitter to connect the DVD/VCR to the for VHF and UHF reception. 75 ohm Coaxial Cable (supplied) VHF/UHF IN NOTE: If a VHF or UHF antenna is used, set the /CA menu option to the "" mode. with single 75 ohm VHF/UHF antenna input 75 ohm Coaxial Cable (supplied) Splitter 75 ohm Input 75/00 ohm outputs (not supplied) UHF VHF NOTE: If a VHF or UHF antenna is used, set the /CA menu option to the "" mode. with 00 ohm UHFand 75 ohm VHF antenna inputs 75 ohm Coaxial Cable (supplied) Splitter 75 ohm Input 00 ohm outputs (not supplied) UHF VHF NOTE: If a VHF or UHF antenna is used, set the /CA menu option to the "" mode. with 00 ohm UHF and 00 ohm VHF antenna inputs
CA (CABLE ) connections Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, you must have a descrambler box for proper reception. DVD/VCR Incoming Cable IN (ANT.) OUT () VHF/UHF IN (ANT) ALLOWS: * Recording of nonscrambled channels. * Use of the programmable timer. * Recording of one channel while watching another. Converter/ Descrambler DVD/VCR Incoming Cable IN (ANT.) OUT () VHF/UHF IN (ANT) ALLOWS: * Recording of channels through the converter box (scrambled and unscrambled). * Using the programmable timer to record only the channel selected at the converter box. PREVENTS: * Recording one channel while watching another. * Using the DVD/VCR tuner to select channels. NOTE: To record from converter/descrambler, DVD/VCR tuner must be tuned to the converter output channel, usually channel or. DVD/VCR Incoming Cable IN (ANT.) Converter/Descrambler VHF/UHF IN (ANT) OUT () ALLOWS: * Recording of nonscrambled channels. * Use of the programmable timer. * Recording an unscrambled channel while watching any channel selected at the converter box. PREVENTS: Recording scrambled channels. NOTE: If you are playing a tape or using the tuner built into the DVD/VCR, the converter must be set to the video channel output of the DVD/VCR (either or ). NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of the Converter/Descrambler box, usually channel or.
CA (CABLE ) connections IMPORTANT: Make sure the /CA menu option is set to the "CA" mode. This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection. Splitter DVD/VCR Incoming Cable Converter/Descrambler IN (ANT.) OUT () A/B Switch A B VHF/UHF IN (ANT) ALLOWS: * Recording of one channel while watching another. * Using the programmable timer to record only the channel selected at the converter box. * Recording of all channels through the converter box. PREVENTS: * Watching scrambled channels while recording another channel. * Using the DVD/VCR tuner to select channels. 5 Splitter DVD/VCR Incoming Cable Converter/ Descrambler IN (ANT.) OUT () A/B Switch A B VHF/UHF IN (ANT) ALLOWS: * Recording of nonscrambled channels. * Recording of one channel while watching another. * Watching premium channels through the converter while recording nonscrambled channels. * Using the programmable timer. PREVENTS: Recording scrambled channels. 6 Splitter Converter/ Descrambler DVD/VCR Incoming Cable Converter/ Descrambler IN (ANT.) OUT () A/B Switch A B VHF/UHF IN (ANT) ALLOWS: * Recording of all channels through the converter box. * Recording a scrambled or unscrambled channel while watching another (scrambled or unscrambled) channel. * Using the programmable timer to record only the channel selected at the converter box. PREVENTS: Using the DVD/VCR tuner to select channels. 5
OPTICAL COAXIAL OPTICAL L R COAXIAL L R Y PB/CB PR/CR Y PB/CB PR/CR ( ANT. ) ( ) ( ANT. ) ( ) OPTICAL COAXIAL L R Y PB/CB PR/CR ( ANT. ) ( ) Playback Connection The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs. Connect to a with Audio/Video Output Use the supplied AUDIO/VIDEO Cord. Audio (L) Output DVD/VCR Video Output DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT VIDEO L AUDIO R CH. IN OUT Audio (R) Output To Video Input To Audio (R) Input To Audio (L) Input AUDIO/VIDEO Cord (supplied) Connect to a with S-Video Output DVD/VCR S-Video Cord (not supplied) DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT VIDEO L AUDIO R CH. IN OUT S-Video Output Audio (L) Output Audio (R) Output To S-Video Input AUDIO Cord (not supplied) To Audio (R) Input To Audio (L) Input Connect to a BS TUNER VHF/UHF Antenna Satellite Antenna ANT. Input 75 ohm Coaxial Cable (not supplied) DVD/VCR To ANT. Input BS Tuner 6 ANT. output DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT Video Output Audio (L) Output Audio (R) Output VIDEO L AUDIO R CH. IN OUT ANT. Output 75 ohm Coaxial Cable (supplied) AUDIO/VIDEO Cord (supplied) To ANT. Input
OPTICAL COAXIAL L R OPTICAL COAXIAL Y PB/CB PR/CR L R ( ANT. ) ( ) Y PB/CB PR/CR ( ANT. ) ( ) Connect to a Stereo Amplifier with Audio Output Playback Connection If your has a COMPONENT VIDEO IN jack, you can connect the DVD/VCR to the with a COMPONENT cable (not supplied) as shown below. COMPONENT VIDEO output jack can send higher-quality video signal to a than S-Video output. DVD/VCR To Component Video Output COMPONENT VIDEO Cord (not supplied) AUDIO/VIDEO Cord (supplied) To Audio/Video Output To Audio/Video Input To Component Video Input DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT VIDEO L AUDIO R CH. IN OUT Stereo Amplifier Audio (L) Output Audio (R) Output To Audio (L) Input To Audio (R) Input AUDIO Cord (not supplied) Connect to an AV Amplifier with built-in digital surround If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby Digital and DTS by using the Optical or Coaxial Digital Output. Use this connection to connect an: AV amplifier with built-in *Dolby Digital decoder AV amplifier with built-in *DTS decoder DVD/VCR Video Output Video cord (not supplied) To Video Input Coaxial digital Audio Output DVD OUTPUT DIGITAL AUDIO AUDIO S-VIDEO COMPONENT VIDEO L AUDIO R CH. Coaxial digital cable (not supplied) IN OUT AV Amplifier with built-in various decoder as above NOTE: You may connect to a with a Component video cable(not supplied) or S-Video cable(not supplied) instead of a video cable(not supplied). Connecting the optical digital cable You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital cable. When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel. When not using the optical digital cable, attach the dust protection cap to protect against dust. NOTE: The OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT jacks are useful only for DVD section. The VHS signal is output only from the composite jack(dvd/vcr VIDEO OUTPUT) and UHF/VHF OUT. When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged. Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers. DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is necessary. When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs. Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit. 7
Setting the Video Channel / Setting the language Setting the Video Channel To view playback of a recorded tape, or to watch a program selected by the VCR's channel selector, the must be set to channel or (video channel). VCR DVD DVD MARKER RETURN DIS A.TRK C.RE ZERO RETURN When a is connected with the 75 ohm coaxial cable only. 5 6 Press to turn on the DVD/VCR. Slide /VCR/DVD switch to VCR/DVD. Then press VCR to select the VCR mode. The VCR indicator on the front panel will light. Set the / Channel selector switch on the rear panel to CH or. Turn ON the and set to CH or to correspond with the channel selected in step. Press /VCR to select the VCR position. The VCR indicator will appear in the display. Select any channel to receive a station in your area. The channel number will appear on the screen for about seconds. For a push-button tuner If CH or corresponding to the video channel cannot be tuned on your, proceed as follows: set the VCR / channel selector and the to CH or, play back a prerecorded tape and tune the to receive a sharp color picture from the video cassette recorder. Refer to your owner's manual for details. NOTE: If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again. If no buttons are pressed for more than 60 seconds,the screen will return to normal operation automatically. Both the VCR and the DVD have their own menu options (See page 6). 8 0 TIMER /VCR UP /VCR CH + /VCR VOL Setting the language You can choose from three different languages (English, French and Spanish) for the on-screen displays. Press UP, If you use the unit for the first time and press UP, instead of the main menu screen on the right the SYSTEM UP menu screen in step may appear. Press or to select the LANGUAGE option, then press ENTER. Press or to select the desired language: English (ENGLISH), Spanish (ESPAÑOL) or French (FRANCAIS), then press ENTER. TIMER AUTO REPEAT ON O SAP ON O SURROUND CH UP SYSTEM UP ON O +/-/ SYSTEM UP CLOCK LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND ON O AUTO CLOCK STANDARD TIME ON O DAYLIGHT SAVING TIME +/-/ Press UP until the screen is cleared.
Tuner Setting This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR s memory. In addition to normal VHF and UHF channels, this DVD/ VCR can receive up to Cable channels. To use this DVD/VCR with an antenna, set the /CA menu option to the mode. When shipped from the factory, this menu option is in the CA mode. VCR DVD Preparation: Turn ON the and set it to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) DVD MARKER RETURN DIS A.TRK C.RE ZERO RETURN /CA Selection Press UP. The VCR menu screen will appear. Press or to select CH UP, then press ENTER. Press or to select the / CA option. CH UP CA AUTO CH MEMORY ADD/DELETE +/-/ 0 TIMER /VCR VOL Then press ENTER to select the or CA mode. The arrow indicates the selected mode. CH UP CA AUTO CH MEMORY ADD/DELETE - VHF/UHF channels CA - CABLE channels +/-/ /VCR CH + Press UP until the menu screen is cleared. UP /VCR VCR/DVD/ Setting channels automatically The VCR can receive a maximum of 8 channels by presetting the channels into memory. Repeat above step and press or to select AUTO CH MEMORY. CH UP CA AUTO CH MEMORY ADD/DELETE NOTE: You can not select "CH UP" if you set the channel to "L". Then press ENTER. The auto tuning will start. The channel display will count up and when finished, the screen returns to normal. +/-/ CH 00 9
To ADD/DELETE channels / Noise elimination To ADD/DELETE channels You can add the channels you want or delete the channels you do not want manually. Preparation: Turn ON the and set it to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) VCR DVD Repeat the step on page 9. Then press or to select the ADD/DELETE option and press ENTER. CH UP CA AUTO CH MEMORY ADD/DELETE +/-/ DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR VOL To Add or Delete desired channels Press Number keys or / to select a channel number you want to add or delete. To add channels Press ENTER until ADD appears on the screen to set to add the unmemorized channel. ADD CH 00 +/-/0-9/ To delete channels Press ENTER until DELETE appears on the screen to set to delete the channel from memory. The channel number will blink. Repeat to to add or delete other channel. Press UP until the menu screen is cleared. UP /VCR VCR/DVD/ Noise elimination When you don't want to receive a weak signal broadcast, the Blue back screen can be obtained by selecting the NO NOISE BACKGROUND "ON". When the unit is shipped from the factory, the NO NOISE BACKGROUND is set to the "ON". Repeat the steps ~ on page 8 and press or to select NO NOISE BACKGROUND. Press ENTER to select the ON position. SYSTEM UP CLOCK LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND ON O AUTO CLOCK STANDARD TIME ON O DAYLIGHT SAVING TIME +/-/ 0 Press UP until the menu screen is cleared.
Auto clock setting The Auto Clock feature enables the automatic clock setting and updating, and also to set the Time Zone and Daylight Saving Time by receiving XDS (Extended Data Service) information carried on the channel signal. Preparation: You must set the antenna connection before the AC cord plug is inserted into the AC outlet. Make sure the AUTO CH MEMORY(on P.9) is done. VCR DVD DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR UP /VCR VCR/DVD/ VOL NOTE: After Auto Clock setting, in some case the clock may display the other time zone s. You can correct the clock by selecting your Time Zone setting above. When the clock is not set or you set the clock manually, Time Zone setting is not available. Auto clock setting WAIT 0 MINUTES! when the power switch is off, after the connections of the antenna and the power plug. Because the Auto Clock setting feature is activate. After the clock is set automatically, you may have to set the Time Zone and Daylight Saving Time. Press to turn on the DVD/VCR after the Auto Clock operation completed. When shipped from factory, the AUTO CLOCK option is set to ON position. If you turn the DVD/VCR on during Auto Clock setting, the clock is not set. With cable box connection, if the Auto Clock Setting is unsuccessful, please select the PBS channel carrying the XDS information, then turn the DVD/VCR off. After 0 minutes, turn the DVD/VCR on, and if the clock is not set automatically, set the clock manually. (See page ) Time Zone setting (STANDARD TIME) In the rare event that you live within broadcast range of two stations in two different time zones, the DVD/VCR may recognize the wrong station for the AUTO CLOCK set. To correct the situation: Preparation: Turn ON the. When a is connected with an audio/video cable, select the video input mode on the. When a is connected only with an antenna cable, set to the video channel or. Then select VCR position with /VCR. Make sure the VCR mode has been selected. (Is the VCR indicator being light?) (see steps ~ on page 8) Press UP. The VCR menu screen will appear. Press or to select the SYSTEM UP menu, then press ENTER. Press or to select the STANDARD TIME option, then press ENTER. Press or to select your Time Zone, then press the ENTER. SYSTEM UP CLOCK LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND ON O AUTO CLOCK STANDARD TIME ON O DAYLIGHT SAVING TIME +/-/ STANDARD TIME ATLANTIC CENTRAL PACIFIC HAWAII AUTO +/-/ EASTERN MOUNTAIN ALASKA Press UP until the screen is cleared.
Auto clock setting Daylight saving time setting You can set the Daylight saving time automatically or manually. VCR DVD Preparation: Turn ON the. When a is connected with an audio/video cable, select the video input mode on the. When a is connected only with an antenna cable, set to the video channel or. Then select VCR position with /VCR. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) DVD MARKER RETURN DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR VOL Repeat the step on page and press or to select DAYLIGHT SAVING TIME, then press ENTER. Press or to select one of the options, then press ENTER. ON: O: AUTO: for manual setting (forward one hour) for manual setting (back one hour) for automatic setting (read XDS in the signal) SYSTEM UP CLOCK LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND ON O AUTO CLOCK STANDARD TIME ON O DAYLIGHT SAVING TIME +/-/ DAYLIGHT SAVING TIME ON O AUTO +/-/ /VCR CH + When you want to set the Daylight Saving Time manually, on the first Sunday in April you set to ON, and on the last Sunday in October you set to O. UP /VCR VCR/DVD/ NOTES: When shipped from factory, the DAYLIGHT SAVING TIME option is set to AUTO position. When the clock is not set, Daylight Saving Time setting is not available. When there is no Daylight Saving Time in your area, always select O position in step.
Manual clock setting You must set the date and time manually for timer recordings and Daylight Saving Time if the Auto Clock process did not set them correctly. Preparation: Turn ON the and set to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) VCR DVD DVD MARKER RETURN EXAMPLE: Setting the clock to "8:0 AM" October, (WED), 00. Press UP. The VCR menu screen will appear. Press or to select the SYSTEM UP menu, then press ENTER. TIMER AUTO REPEAT ON O SAP ON O SURROUND CH UP SYSTEM UP ON O DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR VOL Press or to select the CLOCK option, then press ENTER. +/-/ SYSTEM UP CLOCK LANGUAGE/IDIOMA/LANGUE NO NOISE BACKGROUND ON O AUTO CLOCK STANDARD TIME ON O DAYLIGHT SAVING TIME +/-/ Press or to set the month, then press ENTER button. MONTH DAY 0 (MON) /VCR CH + YEAR TIME 000 :00AM á+/-//ñ UP /VCR VCR/DVD/ 5 To make corrections any time during the process Press repeatedly until the item you want to change blinks, then press or. Set the day, year and time as in step. MONTH DAY YEAR 0 (WED) 00 TIME 8:0AM NOTE: After a power failure or disconnection of the power, the timer settings will be lost. In this case, reset the present time. 6 After setting the clock, date and time starts functioning automatically. á+/ð//ñ 8:0AM WED
Loading and Unloading a Cassette Tape Use only video cassette tapes marked and. Cassettes marked VHS (or S-VHS ) can be used with this video cassette recorder. However, S-VHS recording is not possible with this model. This model is equipped with SQPB (S-VHS QUASI BACK) that makes it possible to play back S-VHS recordings with regular VHS resolution. HQ VHS is compatible with existing VHS equipment. Loading Push the center of the tape until it is automatically inserted. Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left. An inverted cassette tape cannot be inserted. VCR Erase prevention tab Automatic power ON When you insert a cassette tape the VCR power will turn ON automatically. Automatic playback When loading a cassette tape without an erase prevention tab, playback will start automatically. Unloading Press EJECT on the unit. Remove the cassette tape. Automatic tape eject This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its beginning, the cassette tape will be ejected automatically. To prevent accidental erasure Remove the erase prevention tab with a screwdriver. Screwdriver To record again Cover the hole with a piece of adhesive tape. Erase prevention tab Adhesive tape Tape speed and maximum recording time Tape Speed SP (Standard Play) EP (Extended Play) Video cassette tape T-60 T-0 T-90 T-60 T-0 -/ hours hours -/ hours hour 0 minutes 8 hours 6 hours -/ hours hours -/ hours
VCR DVD Cassette tape Playback Preparation: Turn ON the and set to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) Load a prerecorded tape (When loading a cassette tape without the erase prevention tab, playback will start automatically). To start playback Press. DVD MARKER RETURN DIS A.TRK C.RE ZERO RETURN Playback will start. " " will appear on the screen for about seconds. 0 TIMER /VCR VOL To stop playback Press once. The tape will stop but remain fully loaded and ready to play. " " will appear on the screen for about seconds. To rewind the tape or forward it rapidly /VCR CH + Stop the playback or recording with. UP To rewind the tape: Press. To forward the tape: Press. /VCR VCR/DVD/ NOTE: This VCR selects the playback tape speed SP or EP automatically. The Cassette tape and DVD disc can be played back simultaneously. If you press VCR or DVD, the tape playback and DVD playback alternate with each other on the screen. To stop the tape-winding, press. To switch to playback directly (without ), press. Forward/Reverse picture search mode When the tape is being winded, you can switch to picture search mode (see next page). To do this, press or and hold it down. The unit will resume the tape winding as soon as the button is released. 5
Special playback Picture Search Reverse picture search function Press x or x during the playback. Forward picture search function Press x or x during the playback. To return to playback: Press. Still Picture Press during playback. To resume normal playback: Press. Slow Motion During playback press. To return to playback: Press or. Slow tracking and vertical lock adjustment If noise bars appear in the picture during slow motion, press the + or to reduce the noise bars. If the still picture jitters excessively, press + or to stabilize the still picture. Frame by Frame picture Press during playback. Press one by one: The picture advances frame by frame. To return to playback: Press or. Adjusting tracking condition Automatic tracking adjustment Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback. Manual tracking adjustment If automatic tracking cannot eliminate noises well during playback, press +/ to eliminate the noises. MANUAL TR. will appear. Press it briefly for a fine adjustment, or press and hold for a coarse adjustment. Press A.TRK to reactivate automatic tracking again. AUTO TR. will appear. Repeat playback The entire video tape will be played until its end.the tape will then automatically rewind to the beginning and the playback will be repeated. Press UP. Press or to select AUTO REPEAT. Then press ENTER to select [ON] or [O]. If [ON] is selected, the playback will be repeated endlessly. Press UP until the menu screen is cleared. if you press, " " will appear on the screen. To start the playback, press. The playback will be repeated endlessly. To cancel repeat mode: Follow the above step, then press ENTER to select the O position. Press UP to return to the. Skip Search Each time you press while a tape is playing, the unit will fast-forward ahead 0 seconds on the tape. You may press the button up to six times in a row to move 80 seconds (three minutes) ahead. For example: TIMER AUTO REPEAT ON O SAP SURROUND CH UP SYSTEM UP ON ON O O +/-/ press: 0 seconds of tape presses: 60 seconds of tape presses: 90 seconds of tape Note: The audio output is muted during SPEED, STILL, FRAME ADVANCE and MOTION. During picture search mode there will be noise bars which are caused by the system. The Special Playback will automatically change to playback after approx. 5 minutes to protect the video tape against excessive wear. 6
ZERO RETURN function / Video Index Search system ZERO RETURN function This function makes tape-rewinding stop at the counter 00:00:00 position automatically. DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR VOL Preparation: Turn ON the and set it to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) Press. The counter display shows the tape running time during playback or recording. Press C. RE at the desired tape position. The counter display will be reset to the "00:00:00" position (e.g. the begining of recording). VCR VCR 8:7AM LUN STEREO SAP 8:7AM LUN STEREO SAP CAN 00 00 : 0 : 8 SP CAN 00 00 : 00 : 00 SP Press when playback or recording is finished. Press ZERO RETURN. The tape will be rewinded or fast forwarded and automatically stop at the 00:00:00 position. UP The DIS-button Press DIS. The clock and tape counter alternate with each other in the display. VCR /VCR VCR NOTE for Counter Display: If you rewind the tape beyond 00:00:00, a minus sign ( ) will be displayed in front of the time counter. When you load a tape, the counter will reset to 00:00:00. The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes through blank sections, the counter stops. NOTE for Video Index Search system: When you record an INDEX mark at the very beginning of the tape, the mark may not be found. During INDEX search, the tape may stop and begin to play at a slightly different location. INDEX may not function properly with old or worn out video tapes. INDEX marks may not be found if it is extremely close to the point where the search began. In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape. Video Index Search system This function enables you to locate the beginning of any recording made on the VCR. Recording an INDEX MARK The Index Search function automatically records an INDEX mark on the tape whenever a recording is initiated. Index Search Press INDEX or during stop or play mode. For Succeeding programs: Press INDEX. For Preceding programs: Press INDEX. (Additional press increases the INDEX NO. up to 9.) When the INDEX or is pressed, the unit starts searching the INDEX NO. selected and finds the portion, then playback starts automatically. To stop the Index Search, press. INDEX or CH 00 is displayed + INDEX NO. (up to 9) 7
Recording a program Recording and viewing the same program VCR DVD Preparation: Turn ON the and set it to the video input mode. Make sure /VCR/DVD switch has been slided to VCR/DVD. Then press VCR to select the VCR mode. (The VCR indicator will light) Load a cassette tape with the erase prevention tab intact. The VCR will automatically turn on. NOTE: If the erase prevention tab is removed, the tape will eject when both the and are pressed for recording. If you wish to watch the DVD playback during the normal recording on VCR, press DVD to change to DVD mode and perform the DVD playback(see P.7). 8 DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR UP /VCR VCR/DVD/ VOL 5 Press to select the desired tape speed SP or EP. The tape counter and SP or EP will appear on the screen for about seconds. Set the /CA option to the appropriate position (See page 9). - VHF/UHF channels CA - CABLE channels Press Number keys or VCR CH +/ to select the channel to be recorded. VHF/UHF/CA CHANNELS VHF - UHF -69 On the VCR, press. Or on the Remote, while holding, press. " " will appear on the screen for about seconds and will appear on the display. CA VHF - STD/HRC/IRC -6 (A) (W) 7-59 (AA) (WW) 60-85 (AAA) (ZZZ) 86-9 (86) (9) 95-99 (A-5) (A-) 00-5 (00)(5) 0 (5A) INDEX 00 : 00 : 00 SP -9 Press 0 twice and then -9 as required. Example: To select, Press 00. 0- Press 0 first and then the remaining digits in order from left to right. Example: Press 0 for. CH 0-99 Press digits in order. Example: Press for. 00-5 Press the digits in order. Example: Press 0 for 0. CH 0
To stop recording Recording a program Press to stop recording. " " will appear on screen for about seconds. VCR DVD To stop recording temporarily Press to avoid recording unwanted material. Press again to continue the recording. " " will appear on screen for about seconds. DVD MARKER RETURN /VCR CH + DIS A.TRK C.RE ZERO RETURN 0 TIMER /VCR UP /VCR VCR/DVD/ VOL NOTE: The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the mode. You can select a recording channel in the recording pause mode. Recording one program while watching another While the VCR is recording, press /VCR to select the position. The VCR will go off and recording will continue. Select the channel you want to watch by using the channel selector. If the connected is JVC s, use CH +/ after slide / VCR/DVD switch to. NOTE: Some CA hookups do not permit viewing one channel while recording another. See pages,5. To Display VCR operation Status Press. The clock, day of the week and more information will be indicated. While watching CLOCK STEREO AND SEPARATE AUDIO PROGRAM (SAP) 8 : 7AM MON STEREO SAP DAY OF THE WEEK CH 5 00 : 00 : 00 SP CHANNEL TAPE SPEED REAL TIME COUNTER Auto Rewind feature This VCR will automatically rewind the tape when the tape has ended (except during ITR and TIMER ). It will also eject the tape. While operating a tape HI-FI STEREO AUTO REPEAT 8 : 0AM MON HI-FI CH 5 00 : 00 : 00 SP OPERATING MODE TAPE IN To cancel the display: Press until all indicators disappear. 9