LINE ARRAY PROGRAMMER ACD- / ACD- WCD v.. ACD- / ACD- - WCD- Engineered and made in E.U. MAIN FUNCTIS Back light control. Volume control. Bass control Treble control band graphic equalizer. Vertical Beam Steering Input control. Speech enhancement. Mute control. DESCRIPTI The WCD- developed by UNI DESARROLLOS ELECTRICOS is the equipment that allows the adjustments of the line array columns ACD- and ACD-. With a screen of 4, with high resolution features in LCD technology. Developed with a usability and smart menu control navigation. It makes a really easy way to do the start up of the line array on site. 7 Plug and play the WCD- programmer into a line array, after it will be showed on the screen the current column configuration, where it is possible to adjust in real time all configuration parameters. 4 Point to point, between the WCD- programmer and the ACD- /ACD- columns can be done with the UTP CAT wire supplied. The WCD- power supply will be also provided by the same connection UTP wire, no need of external power supply is required. 7 7 WCD- & ACCESSORIES: WCD- module programmer UTP wire (RJ-4 / J-4) meters long. - Screen size: - Screen resolution: - Power supply: - Connection socket: - Wire type: - Maximum bus distance: - Communication protocol: - Power consumption: - Material: TECHNICAL DATA WCD- 4 4 x VDC (from ACD- / ACD-) RJ-4 UTP. CAT metros RS-4 Half-duplex ma. Aluminium and plastic UNI DESARROLLOS ELECTRICOS Barcelona Avda. BARCELA, 4 97 - SANT JOAN DESPÍ BARCELA - ESPAÑA UDE reserves the right to modify the technical characteristics of its products without previous notice Tel: +4 9 477 4 Fax: +4 9 7 ude@udeaudio.com Madrid C/ LUIS I,, ª planta - MADRID ESPAÑA Tel: +4 9 7 Fax: +4 9 4 9 97 centro@udeaudio.com PUBLIC ADDRESS Systems.47A
WCD- CNECTI Once the audio signal and the power supply is connected to the ACD- / ACD-, it is recommended to configure with the WCD- programmer. Plug the wire in the WCD- and the control socket in the front of the ACD-/ACD- line array with a UTP CAT wire supplied (A) A DISPLAY LED CFIG Initially a UDE logo will be displayed with the WCD- and column (ACD) firmware version. After a communication check and data transfer the configuration menu will appear. a WCD v.. ACD v.. A b The wire should be IEC compliance (UTP CAT and RJ-4). STRAIGHT CABLE B 7 4 4 7 BROWN 7 BROWN-WHITE 4 GREEN BLUE-WHITE BLUE GREEN-WHITE ORANGE ORANGE-WHITE screen + FLASHING Led CFIG In case the communication data is not ready, the programmer will show the configuration page, without the option to enter in any menu. Fixed light screen + Led CFIG When the communication is ready, information led light will keep on and the user is ready to configure all options. c d.47a
SYSTEM PROGRAMMING The ACD- and ACD- line array have an internal configuration stored in a non volatile memory, that will be send each time via RS-4 to the WCD-, for a system programming. Navigate through the icons with the keyboards. Select the desired option with the button. It will appear the desired menu selection were is possible to visualize and edit the data..47a
OPTIS Control + Back light menu control allows setting manually the backlight brightness of the LCD screen. or decrease the brightness backlight + +4 The pre set value is. Press button to return on the UME Control UME + + +4 Volume control allows setting the power volume of the line array from a range of to 4. Minimum volume: Maximum volume: +4 or decrease volume. The pre set value is. Press button to return on the Control + Bass control allows setting the bass gain (volume) from - to +, in steps of. or decrease bass control. - + The pre set value is. Press button to return on the Control -4 Treble control allows setting the treble gain (volume) from - to +, in steps of. With the navigation buttons it will increase or decrease treble control. - + The pre set value is. Press button to return on the Graphic UALIZER UALIZATI 4, khz + db In the equalization menu, it allow to manage frequency: - Hz - Hz. - 4Hz - Hz - Hz - khz -.khz -.khz -.khz -.khz - 4.kHz -.4kHz - 9.kHz -,khz -.khz. Each frequency can be amplified or attenuated from a total range of - to + in steps of. The pre set value in all frequencies is db. Select the frequency with the horizontal navigation keys The frequency selected must be showed. or the volume level with the vertical navigation keys. Press button to return on the.47a 4
OPTIS AIMING adjustment. +4 The aiming angle menu allow to set electronically the inclination angle of the beam. The configuration total range is from -4 to +4. With the navigation keys it will increase or decrease the angle. -4 The pre set value is. Press button to return on the volume adjustment db In the input volume menu, there are options: - db - -db - -db between options. db - db - db Depending on the previous source audio and the level signal transmitted a choice option might be selected. XLR and LV audio inputs would be affected with this menu option Press button to return on the The pre set is db. Speech In the speech filter menu it can be set an audio reinforcement for the speech spectrum. between / icons. The pre set value is. Press button to return on the control In the speech filter menu it can be set an audio reinforcement for the speech spectrum. between / icons. The pre set value is. The function is disabled if the power is switched. Press button to return on the ATTENTI! The configuration changes made through the WCD- are applied and saved in real time in the line array. If the line array programmer is unplugged from the column, all changes done would be saved in the internal column memory..47a