Test & Measurement Data Sheet 03.00 EUTRA/LTE Downlink Specifications R&S FS-K100PC/-K102PC/-K104PC R&S FSV-K100/-K102/-K104 R&S FSQ-K100/-K102/-K104 R&S FSW-K100/-K102/-K104
CONTENTS Definitions... 3 Specifications... 4 Minimum system requirements for PC software R&S FS-K100/102/104PC... 4 Running on a PC... 4 Running on an R&S FSQ... 4 EUTRA/LTE downlink analysis... 4 Frequency... 4 Level... 4 Signal acquisition... 4 Measurement parameters... 5 Result display... 5 Measurement uncertainty (nominal)... 6 Base station output power... 6 Transmitted signal quality... 6 Ordering information... 7 The specifications of the R&S FS-K100/102/104PC, R&S FSW-K100/102/104, R&S FSV-K100/102/104 and R&S FSQ-K100/102/104 EUTRA/LTE downlink are based on the data sheet specifications of the R&S FSW, R&S FSV, R&S FSQ, R&S FSG and R&S RTO1044 signal and spectrum analyzers and oscilloscope, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are given as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to reduced signal to noise ratio (S/N). In line with the 3GPP standard, chip rates are specified in Mcps (million chips per second), whereas bit rates and symbol rates are specified in kbps (thousand bits per second) or ksps (thousand symbols per second). Mcps, kbps and ksps are not SI units. 2 Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink
Definitions General Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation Specified environmental conditions met Recommended calibration interval adhered to All internal automatic adjustments performed, if applicable Specifications with limits Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked with limiting symbols such as <,, >,, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if applicable. Specifications without limits Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent values with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance is ensured by design. Typical data (typ.) Characterizes product performance by means of representative information for the given parameter. When marked with <, > or as a range, it represents the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents the mean value. Nominal values (nom.) Characterize product performance by means of a representative value for the given parameter (e.g. nominal impedance). In contrast to typical data, a statistical evaluation does not take place and the parameter is not tested during production. Measured values (meas.) Characterize expected product performance by means of measurement results gained from individual samples. Uncertainties Represent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has been calculated in line with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into account environmental conditions, aging, wear and tear. Device settings and GUI parameters are designated with the format parameter: value. Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz. Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink 3
Specifications Minimum system requirements for PC software R&S FS-K100/102/104PC The R&S FS-K100/102/104PC EUTRA/LTE downlink PC software is compatible with the R&S FSW, R&S FSQ, R&S FSG and R&S FSV signal and spectrum analyzers. Running on a PC Operating system Windows XP Professional + Service Pack 2, Windows 7 Free hard disk space 1 Gbyte Free RAM 512 Mbyte Graphics resolution 800 600 pixel Measuring instrument connection IEC/IEEE bus or LAN connection, VISA driver Running on an R&S FSQ Some options and features require a minimum memory size of at least 1024 Mbyte and are marked accordingly in the following. R&S FSQs that do not have a CPU-board order number 1091.3104 (see SETUP SYSTEM INFO HARDWARE INFO) cannot be upgraded to 1024 Mbyte memory size. EUTRA/LTE downlink analysis Frequency Frequency range RF input same as R&S FSW/FSQ/FSG/FSV/RTO 1 Level I/Q baseband inputs (R&S FSQ-B71) DC to 36 MHz Level range RF input 50 dbm to +30 dbm 1 Signal acquisition I/Q baseband inputs (R&S FSQ-B71) 31.6 mv to 5.62 V Supported standards EUTRA/LTE downlink in line with [1] Capture length 20.1 ms to 50.1 ms 2 Sweep time spectrum mask auto adjacent channel leakage ratio (ACLR) 500 ms Trigger modes RF input free run, external, IF power 1 I/Q baseband inputs (R&S FSQ-B71) free run, external 1 2 For signal and spectrum analyzers, restricted IF overload, IF power trigger and auto level functionality depending on carrier frequency and bandwidth at carrier frequencies < 50 MHz. For R&S RTO, the R&S RTO-K11 I/Q software interface and the R&S RTO-B4 OCXO 10 MHz are required. Running R&S FS-K100/102/104PC on an R&S FSQ with a memory size of less than 1024 Mbyte, the maximum capture length is restricted to 20.1 ms. 4 Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink
Measurement parameters Input RF R&S FSQ-B71 option required I/Q baseband, balanced-to-unbalanced switchover R&S FSW/FSQ/FSV-B17 option required digital baseband interface Duplexing FDD 3, TDD 4 Channel bandwidth 1.4/3/5/10/15/20 MHz 5 MIMO configuration 1, 2, 4 TX antennas antenna selection either antenna 1, 2, 3, 4 (depending on MIMO configuration) antenna selection (depending on MIMO configuration) 6 either antenna 1, 2, 3, 4 or all antennas or auto (1 antenna) or auto (2 antennas) or auto (4 antennas) PDSCH resource allocation four frames can be allocated modulation QPSK, 16QAM, 64QAM MIMO precoding type 6 none, transmit diversity, spatial multiplexing, beamforming (UE-spec. RS) Multicarrier filter on/off Spectrum emission mask/adjacent channel leakage power ratio (ACLR) 7 category 8 A, B (option 1, option 2 9 ), local area 9, home 9 assumed adjacent channel carrier 8 EUTRA of same bandwidth, 1.28 Mcps UTRA, 3.84 Mcps UTRA, 7.68 Mcps UTRA ACLR noise correction on/off auto gating on/off Result display R&S FS-K100/102/104PC R&S FSW-K100/102/104 R&S FSQ-K100/102/104 R&S FSV-K100/102/104 Result summary EVM PDSCH QPSK EVM PDSCH 16QAM EVM PDSCH 64QAM EVM physical channel EVM physical signal EVM all Center frequency error Sampling error Time alignment error 2.1, 3.1, 4.1 10 I/Q offset I/Q gain imbalance I/Q quadrature error RSTP (reference signal TX power) OSTP (OFDM symbol TX power) Power Crest factor Power versus time Capture buffer On/off power Power versus symbol and carrier 3 4 5 6 7 8 9 R&S FSW/FSQ/FSV/FS-K100(PC) option required. R&S FSW/FSQ/FSV/FS-K104(PC) option required. For R&S FSW, R&S FSW-B28 required for channel bandwidths >10 MHz. R&S FS-K102PC option required. The R&S FS-K102PC option requires at least 1024 Mbyte of memory. Spectrum emission mask/adjacent channel leakage power ratio (ACLR) are not supported for R&S RTO. As defined in section 6.6 of 3GPP TS 36.141 v10.0.0. Only supported by R&S FS-K100/102/104PC. 10 R&S FSW/FSQ/FSV/FS-K102(PC) option required. Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink 5
R&S FS-K100/102/104PC R&S FSW-K100/102/104 R&S FSQ-K100/102/104 R&S FSV-K100/102/104 EVM EVM versus carrier EVM versus symbol EVM versus symbol and carrier EVM versus resource block frequency error versus symbol EVM versus subframe Spectrum Power spectrum Power versus resource block Channel flatness Channel flatness difference Channel group delay Spectrum mask ACLR Constellation Constellation diagram Statistics/miscellaneous CCDF Signal flow Allocation summary list Bit stream Allocation ID versus symbol and carrier Channel decoder results Beamforming UE RS weights (magnitude/phase) Measurement uncertainty (nominal) Base station output power Base station output power R&S FSW R&S FSQ R&S FSG R&S FSV R&S RTO1044 AUTS 11 Level uncertainty same as R&S FSW/FSQ/FSG/FSV/RTO (see R&S FSW/FSQ/FSG/FSV/RTO total measurement uncertainty) 0.7 db Transmitted signal quality EVM R&S FSW R&S FSQ R&S FSG R&S FSV R&S RTO1044 12 AUTS 11 Residual EVM test model 3.1, 10 MHz 13 level 25 dbm to +15 dbm input = RF (0.6 GHz < f < 2.7 GHz) channel estimation: 3GPP EVM definition EVM calculation method: 3GPP EVM definition phase tracking: off timing tracking: off < 49 db < 47 db < 46 db < 46 db < 42 db Frequency error Uncertainty 1 Hz + R&S FSW/FSQ/FSG/FSV/RTO frequency uncertainty (see R&S FSW/FSQ/FSG/FSV/RTO reference frequency) 12 Hz Time alignment between transmitter branches Uncertainty test model 1.1, 10 MHz 13 < 2.5 ns < 2.5 ns < 2.5 ns < 2.5 ns < 2.5 ns 25 ns References [1] 3GPP TS 36.211 V10.0.0 (2010-12), 3rd Generation Partnership Project; Technical Specification Group Radio Access Network; Evolved Universal Terrestrial Radio Access (E-UTRA); Physical Channels and Modulation (Release 10). 11 Acceptable uncertainty of test system, in line with 3GPP TS 36.141 v10.0.0. 12 All measurement results obtained under the use of an external reference frequency. 13 Test model as defined in section 6.1 of 3GPP TS 36.141 v10.0.0. 6 Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink
Ordering information Designation Type Order No. LTE FDD Downlink PC Software R&S FS-K100PC 1309.9916.06 (requires R&S FSPC) LTE MIMO Downlink PC Software R&S FS-K102PC 1309.9939.06 (requires either R&S FS-K100PC or R&S FS-K104PC) LTE TDD Downlink PC Software R&S FS-K104PC 1309.9951.06 (requires R&S FSPC) FSPC Licence Dongle R&S FSPC 1310.0002.02 EUTRA/LTE FDD Downlink Measurement Application R&S FSW-K100 1313.1545.02 EUTRA/LTE Downlink MIMO R&S FSW-K102 1313.1568.02 (requires either R&S FSW-K100 or R&S FSW-K104) EUTRA/LTE TDD Downlink Measurement Application R&S FSW-K104 1313.1574.02 EUTRA/LTE FDD Downlink Measurement Application R&S FSQ-K100 1308.9006.02 EUTRA/LTE Downlink MIMO R&S FSQ-K102 1309.9000.02 (requires either R&S FSQ-K100 or R&S FSQ-K104) EUTRA/LTE TDD Downlink Measurement Application R&S FSQ-K104 1309.9422.02 EUTRA/LTE FDD Downlink Measurement Application R&S FSV-K100 1310.9051.02 EUTRA/LTE Downlink MIMO R&S FSV-K102 1310.9151.02 (requires either R&S FSV-K100 or R&S FSV-K104) EUTRA/LTE TDD Downlink Measurement Application R&S FSV-K104 1309.9774.02 Signal Analyzer, 2 Hz to 8 GHz R&S FSW8 1312.8000.08 Signal Analyzer, 2 Hz to 13.6 GHz R&S FSW13 1312.8000.13 Signal Analyzer, 2 Hz to 26.5 GHz R&S FSW26 1312.8000.26 Signal Analyzer, 20 Hz to 3.6 GHz R&S FSQ3 1313.9100.03 Signal Analyzer, 20 Hz to 8 GHz R&S FSQ8 1313.9100.08 Signal Analyzer, 20 Hz to 26.5 GHz R&S FSQ26 1313.9100.26 Signal Analyzer, 20 Hz to 40 GHz R&S FSQ40 1313.9100.40 Signal Analyzer, 9 khz to 8 GHz R&S FSG8 1309.0002.08 Signal Analyzer, 9 khz to 13.6 GHz R&S FSG13 1309.0002.13 Signal Analyzer, 9 khz to 3.6 GHz R&S FSV3 1307.9002.03 Signal Analyzer, 9 khz to 7 GHz R&S FSV7 1307.9002.07 Signal Analyzer, 9 khz to 13.6 GHz R&S FSV13 1307.9002.13 Signal Analyzer, 9 khz to 30 GHz R&S FSV30 1307.9002.30 Signal Analyzer, 9 khz to 40 GHz R&S FSV40 1307.9002.40 Digital Oscilloscope, 4 GHz, 4 channels R&S RTO1044 1316.1000.44 (requires R&S RTO-K11 and R&S RTO-B4) I/Q Software Interface R&S RTO-K11 1317.2975.02 OCXO 10 MHz R&S RTO-B4 1304.8305.02 Recommended options and extras 28 MHz Analysis Bandwidth R&S FSW-B28 1313.1645.02 RF Preamplifier R&S FSW-B24 1313.0832.13/26 Electronic Attenuator, 1 db steps R&S FSW-B25 1313.0990.02 I/Q Baseband Inputs R&S FSQ-B71 1157.0113.03 Digital Baseband Interface R&S FSW-B17 1313.0784.02 Digital Baseband Interface R&S FSQ-B17 1163.0063.02 Digital Baseband Interface R&S FSV-B17 1310.9568.02 Trigger Unit R&S FS-Z11 5013.4547.02 Rohde & Schwarz R&S FS-K100/102/104PC, R&S FSx-K100/102/104 EUTRA/LTE Downlink 7
Service you can rely on Worldwide Local and personalized Customized and flexible Uncompromising quality Long-term dependability About Rohde & Schwarz Rohde & Schwarz is an independent group of companies specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting, radiomonitoring and radiolocation, as well as secure communications. Established more than 75 years ago, Rohde & Schwarz has a global presence and a dedicated service network in over 70 countries. Company headquarters are in Munich, Germany. Environmental commitment Energy-efficient products Continuous improvement in environmental sustainability ISO 14001-certified environmental management system Certified Quality System ISO 9001 Rohde & Schwarz GmbH & Co. KG www.rohde-schwarz.com Regional contact Europe, Africa, Middle East +49 89 4129 12345 customersupport@rohde-schwarz.com North America 1 888 TEST RSA (1 888 837 87 72) customer.support@rsa.rohde-schwarz.com Latin America +1 410 910 79 88 customersupport.la@rohde-schwarz.com Asia/Pacific +65 65 13 04 88 customersupport.asia@rohde-schwarz.com China +86 800 810 8228/+86 400 650 5896 customersupport.china@rohde-schwarz.com R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG Trade names are trademarks of the owners Printed in Germany (as) PD 3606.7318.22 Version 03.00 December 2012 R&S FS-K100/102/104PC, R&S FSx-K100/102/104 Subject to change 2012 Rohde & Schwarz GmbH & Co. KG 81671 München, Germany 3606731822