Installation Guide CVC 00 Component and HDTV to RGB Converter --0 Rev. B 0
V A MAX 0 0 0 0 0 LAN Introduction The Extron CVC 00 Component Converter converts all standard component video formats: NTSC/PAL, DVD, and Betacam, to RGBHV or RGBS; and converts SMPTE HDTV component video to RGBHV. The CVC 00 can also strip sync-on-green (SOG) from RGsB video. The converter outputs RGBHV or RGBS video on BNC connectors. The figure below shows a typical CVC 00 application. Extron CVC 00 Component Converter Component POWER INPUT PR/R Y/G PB/B CVC 00 R G B H/HV V OUTPUT RGBHV Projector or OUTPUTS DSS Receiver or INPUTS OUTPUTS RESET ACT LINK INPUTS Blu-ray Disc Matrix Switcher The component video input formats include SMPTE, HDTV and Betacam component video. The RGsB video input can be computer video or NTSC/PAL video. Mounting The U high, quarter rack width, CVC 00 converter can be mounted to a rack, under a desk or tabletop, or on a projector bracket. It can be rack mounted using one-quarter of a U Universal Rack Shelf, RSU (part #0-0-0) or U Basic Rack Shelf, RSB (part #0-0-0). UL rack mounting guidelines The following Underwriters Laboratories (UL) guidelines pertain to the installation of the CVC 00 into a rack.. CVC 00 Installation Elevated operating ambient temperature If the equipment is installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, install the converter in an environment compatible with the maximum ambient temperature (Tma = +0 F, +0 C) specified by Extron.
Mounting.... Reduced air flow Install the equipment in a rack so that the amount of air flow required for safe operation of the equipment is not compromised. Mechanical loading Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven mechanical loading. Circuit overloading Connect the equipment to the supply circuit and consider the effect that circuit overloading might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern. Reliable earthing (grounding) Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (e.g. use of power strips). Mounting instructions Rack mount the CVC 00 as follows:.. Remove the feet from the CVC, if they were previously installed. Mount the CVC 00 on the rack shelf, using two -0 x /" screws in opposite corners (under the shelf) to secure the converter to the shelf (see below). U Universal Rack Shelf / Rack Width Front False Faceplate / Rack Width Front False Faceplate Both front false faceplates use screws. () -0 x /" Screws Use mounting holes on opposite corners. CVC 00 Installation
Cable Connection and Rate Selection Cable Connection and Rate Selection See the illustrations below to identify the panel connections. b d INPUT PR/R Y/G PB/B CVC 00 POWER V.0 A MAX R G B H/HV V FORMAT OUTPUT CVC 00 COMPONENT VIDEO CONVERTER a a b c Power connector Plug the external VDC power supply here using the included -pole captive screw connector (See "Power supply wiring"). Input connectors Connect a component (SMPTE, HDTV, or Betacam) or RGsB video input device to these female BNC connectors. Connect the input device as shown below. e Y, PR, PB PR /R Y/G PB /B Y, B-Y, R-Y R-Y B-Y PR /R Y/G PB /B RGsB (SOG) c PR /R Y/G PB /B Output connectors Connect an RGBHV or RGBS display to these female BNC connectors. Connect the display as shown below. RGBHV R G B H/HV V RGBS R G B H/HV V d Power LED Green when power is applied and an active video input is detected. Amber if power is available but no input signal is present. CVC 00 Cable Connection
Cable Connection and Rate Selection (Cont d) e Input Format rotary switch Use an Extron Tweeker or other small screwdriver to set the Format rotary switch to match the video input format. The following table shows switch settings and their assigned input video formats. Position Input Resolutions Output Position 0 Reserved for future use Position 0p, p, 0p, YUVp/HD (Default): 00i, 00p RGBHV Position : RGsB 0i/p, i/p, 0x0 to 0x00 RGBHV Position : YUVi 0i, i RGBHV Position : RGsB HD 0p, 00i, 00p RGBHV Position : Betacam 0 0i, i RGBHV Position : Betacam 0 0i, i RGBHV Position : YUVp 0p, p RGBS Position RGsB 0i/p, i/p, 0x0 to 0x00 RGBS Position : YUVi 0i, i RGBS Position A: RGsB HD 0p, 00i, 00p RGBS Position B: Betacam 0 0i, i RGBS Position C: Betacam 0 0i, i RGBS D, E and F Reserved for future use Input Format Table (Rotary Switch) CVC 00 Rate Selection
Power Supply Wiring Power supply wiring N This product is intended to be powered by a UL Listed power supply with an output rated at VDC, A. A Wire the supplied male power connector (plug) as shown below. Smooth Ridges + _ A SECTION A A Power Supply Output Cord Tie Wrap Captive Screw Connector C Power supply voltage polarity is critical. Incorrect polarity can damage the power supply and the product. Identify the power cord negative lead by the ridges on the side of the cord. N The length of the exposed (stripped) copper wires is important. The ideal length is / ( mm). Longer bare wires can short together. Shorter wires are not as secure in the captive screw connectors and could be pulled out. Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out. To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter. W The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring. As an alternative, an Extron PS Universal VDC Power Supply, part #0--0, can power multiple Extron VDC devices using only one AC power connector. Insert the wired plug into the power connector on the rear panel, then connect AC power. CVC 00 Power Supply Wiring
Specifications input Number/signal type... component video [HDTV (Y, PR, PB), SMPTE (Y, R-Y, B-Y), or Betacam (Y, R-Y, B-Y)] or RGsB Connectors... BNC female Nominal level... Vp-p for Y of component video and for G of RGsB 0. Vp-p for P B, P R, R-Y and B-Y of component video, and for R and B of RGsB Minimum/maximum levels... 0 V to. Vp-p with no offset Impedance... ohms Horizontal frequency... khz to 00 khz according to selected mode Vertical frequency... 0 Hz to 0 Hz Resolution range... 0x0 to 0x00, 0i/p, i/p, 0p, 00i/p Return loss... <- db @ 0 MHz output Number/signal type... RGBHV, RGBS Connectors... BNC female Nominal level... 0. Vp-p for RGB Minimum/maximum levels... RGB: 0.0 V to 0. Vp-p Impedance... ohms Return loss... <- db @ 0 MHz Vertical frequencies... Locked to the detected input rate Sync Input type... RGsB; YUV; Y, R-Y, B-Y Output type... RGBHV, RGBS Standards... SMPTE 0M (NTSC), SMPTE M (00i/p), SMPTE M (0p), SMPTE M (0p) Input level... 0. V to.0 Vp-p (sync + video) Output level... 0.0 V to.0 Vp-p Input impedance... ohms (on Y or Gs connector) Output impedance... ohms (on H/HV and V connectors) CVC 00 Specifications
Specifications (Cont d) General External power supply... 00 VAC to 0 VAC, 0-0 Hz, external; to VDC, A, regulated Power input requirements... VDC,.0 A Temperature/humidity... Storage: -0 to + F (-0 to +0 C) / 0% to 0%, noncondensing Operating: + to +0 F (0 to +0 C) / 0% to 0%, noncondensing Cooling... Convection, no vents Mounting Rack mount... Yes, with optional U,." deep rack shelf (RSU, #0-0-0; RSB, 0-0-0); or U, " deep rack shelf (RSU, #0-0-0; RSB, 0-0-0) Furniture mount... Yes, with optional MBU Under Desk Mount kit (0-0-0) or MBU Through Desk Mount kit (0-0-0) Enclosure type... Metal Enclosure dimensions...." H x." W x.0" D (U high, quarter rack wide) (. cm H x 0. cm W x. cm D) (Depth excludes connectors.) Product weight... 0. lbs (0. kg) Shipping weight... lbs ( kg) Vibration... ISTA A in carton (International Safe Transit Association) Regulatory compliance Safety... CE, CUL, UL EMI/EMC... CE, C-tick, FCC Class A, ICES, VCCI Class A MTBF... 0,000 hours Warranty... years parts and labor N All nominal levels are at ±0%. N Specifications are subject to change without notice. Extron USA - West Headquarters +00.. Inside USA / Canada Only +...00 +... FAX Extron USA - East +00.. Inside USA / Canada Only +... +... FAX Extron Europe +00.. Inside Europe Only +...00 +...00 FAX Extron Asia +00.. Inside Asia Only +..00 +.. FAX Extron Japan +... +... FAX 00 Extron Electronics. All rights reserved. Extron China +00.. Inside China Only +..0. +..0. FAX Extron Middle East +..00 +..0 FAX