YHT-700 QUICK-CONNECT GUIDE

YHT-700 QUICK-CONNECT GUIDE

INTODUCTION Yamaha developed the YHT-700 A/V Home Theater package to turn your home into a theater. In addition to enhancing the sound of a video source, like your,, or VC, the YHT-700 also superbly reproduces audio sources, such as a CD player or a cassette deck. This Quick-Connect Guide will help you get started. Study the speaker system plan (below), and then use the interconnect diagrams (on the following pages) to connect the receiver, player and speakers to your system. For the video portion, you will need a television or monitor. efer to the Yamaha HT-5550 Ownerís Manual, as well as those that came with your other components, for complete instructions and cautions. Be sure to turn off all power while making connections. Save this Quick-Connect Guide for future reference. NOTE: abel the end of each speaker wire (i.e., left rear, right front, etc.) before connecting them to the A/V receiver. For wire runs over 30 feet, use larger 18- or 16-gauge speaker wire. TOOS AND PATS The YHT-700 Home Theater package consists of (1) HT-5550 A/V receiver with (1) universal remote control, (1) DV-C6480 Player, (4) 2-way front/rear speakers, (1) NS-AC480 2-way center-channel speaker, 100' of speaker wire, (1) 0.5 m optical cable, (1) 10' CA audio cable, (1) YST-SW45 Powered Subwoofer, and related owner's manuals. You will also need: Wire strippers (optional) Velcro (for secure fastening of NS-AC480 on a ) Brackets, toggle bolts, molly anchor screws, or sheet metal screws (for securing speakers to walls) NOTE: If you are unsure of how to securely and safely fasten speakers to a wall, please contact a reliable source about the best type of hardware for your particular wall's construction. Secure installation is the purchaser's responsibility. SPEAKE SYSTEM PAN YST-SW45 Subwoofer (on floor) (left side, same height as ) C NS-AC480 (on top or below ) Sub (right side, same height as ) 6'~8' apart = eft Channel = ight Channel C = Center Channel S = Surround Channel Couch istening Area (on stand or wall, at least ear level or preferably higher) S 8'~10' apart S (on stand or wall, at least ear level or preferably higher) 2

CONNECTING AUDIO COMPONENTS Yamaha HT-5550 eceiver (ear Panel) NOTE: For your convenience, the Yamaha HT-5550 receiver is equipped with two switched AC outlets(1 00 W max.). If desired, use them to power on connected components (e.g.,cd player) each time the receiver is turned on. However, do not use them for components equipped with clocks (e.g.,vc). Cassette Deck, CD or MD ecorder * Use Playback Or ine Out ** Use ine In CD Player (Changer) Out Out* Out* In** In** Out CD IN (PAY) MD /CD- (EC) Use CA Cables For Interconnections AUDIO CA Cable Color Codes Yellow = Video White = eft ed = ight 3

CONNECTING THE YHT-700 SPEAKES (Front ight Ch.) ED = positive (+) use clear wire NS-AC480 (Center Channel) (Front eft Ch.) BK = negative (-) use clear with white stripe wire Strip 1/ 4" off ends of speaker wires. oosen terminals. Insert speaker wires; tighten terminals. Stripe Wire - + Stripe Wire Speaker Wiring - + - Stripe Wire + Yamaha HT-5550 A/V eceiver (ear Panel) Set IMPEDANCE Selector to right position. (Surround ight) (Surround eft) YST-SW45 (Subwoofer ear) INPUT2 AUTO /ON HIGH CUT 50 Hz 150 Hz VOUME 0 10 Stripe Wire OFF OW HIGH Initial Settings (on Front Panel also see page 9) - + - + Stripe Wire 4

CONNECTING CABES FO COMPONENTS Yamaha HT-5550 eceiver (ear Panel) NOTE: When using a hi-fi stereo VC, set the Tuner/ine switch (on the VC) to ine position to record from another source connected to the Yamaha HT-5550 receiver. Satellite eceiver (or Cable Box) Video Out Video Out Video In Hi-Fi Stereo VC ANT Out (F Out) Monitor/ Use CA Video Cables And Jacks For Video Interconnections Video In Optional 75-ohm Coaxial Cable ANT In CA Cable Color Codes Yellow = Video White = eft ed = ight For S Video Connections, Please efer To The HT-5550 Owner's Manual 5

CONNECTING THE YAMAHA DV-C6480 PAYE Yamaha HT-5550 eceiver (ear Panel) Analog Out* V Use the Included CA Cables for Analog and Video Connections Between the Player and eceiver. Optical Cable (Included) Connecting Optical Cable emove dust cap. Align plug with terminal and insert cable. NOTES: On both ends of the optical cable, align and firmly insert each plug into its mating terminal. During connection, do not bend the optical cable. Keep dust caps and reattach them if terminals are not used. CA Cable Color Codes Yellow = Video White = eft ed = ight MAIN SUOUND CENTE SUB WOOFE 6CH DISCETE NOTE: Use the optical connection to enjoy 5.1 - channel surround sound found on s recorded in the Dolby Digital or DTS Digital Surround format. 1 P IN MIXED 2CH AUDIO Y COMPONENT (480p/480i) 2 PB S COAXIA OPTICA PCM/ DTS DIGITA EMOTE CONTO Yamaha DV-C6480 Player (ear Panel) *Analog Out connections are required for playback of CD-s and recording from to VC. Dolby Digital is a trademark of Dolby aboratories icensing Corporation. DTS is a trademark of DTS Technology C. 6

CONNECTING AUDIO CABES FO COMPONENTS Yamaha HT-5550 eceiver (ear Panel) Video Player (or Video Game Console) Satellite eceiver Out Out Out Out NOTE: When using a hi-fi stereo VC, set the Tuner/ine switch (on the VC) to ine position to record from another source connected to the Yamaha HT-5550 receiver. V AUDIO V-AUX IN VC D- /CB Out Hi-Fi Stereo VC Out In In MONITO CA Cable Color Codes Yellow = Video White = eft ed = ight Use CA Cables And Jacks For Interconnections 7

CABE HOOK-UP (BASIC AND PEMIUM CHANNES) Yamaha HT-5550 eceiver (ear Panel) NOTE: When using a hi-fi stereo VC, set the Tuner/ine switch (on the VC) to ine position to record from another source connected to the Yamaha HT-5550 receiver. Basic Cable (From Wall Jack) O ANT In In Hi-Fi Stereo VC In Out Video In Video Out Out CA Cables CA Cables AUDIO V V-AUX IN VC D- /CB CA Video Cables Premium Cable (From Wall Jack) Cable Box (Channel 3 or 4 Output) ANT In In Hi-Fi Stereo VC (Tuner set to Channel 3 or 4) In Video In Video Out Out Out CA Cables CA Cables MONITO AUDIO V V-AUX IN VC D- /CB CA Video Cables CA Cable Color Codes Yellow = Video White = eft ed = ight MONITO 8

PUT TO SPEAKES FOM AMPIFIE INPUT 1 INPUT 2 AUTO OFF OW HIGH INITIA ADJUSTMENT OF THE YST-SW45 SUBWOOFE To achieve optimum volume balance between the YST-SW45 Subwoofer and the Main Speakers, perform the following procedure: 1. Insert the YST-SW45's power plug into an AC outlet. 2. On the YST-SW45's rear panel, slide the switch to ON. 3. On the YST-SW45's front panel, set the VOUME control to 0 (minimum setting), the HIGH CUT control to its midpoint position, and press the /ON switch to ON. Then power on all other components. YST-SW45 Subwoofer (ear Panel) 4. Play an audio source and adjust the HT-5550's VOUME control to a desired listening level. 5. On the YST-SW45's front panel, increase the VOUME control gradually to adjust the balance the volume between the YST-SW45 Subwoofer and the Main Speakers. NOTE: Once the volume is balanced between the subwoofer and the main speakers, you can adjust the volume of your whole sound system by using the HT-5550's VOUME control. Initial Settings (on Front Panel) /ON HIGH CUT VOUME 50 Hz 150 Hz 0 10 ON ON OFF OFF To AC Outlet 9

POGAMMING THE UNIVESA EMOTE CONTO Turns On Component's Power Component Selector Buttons CD VC + VO - TANSMIT SYSTEM AV MD/CD- TUNE SEEP D-/CB V-AUX 6CH INPUT A B AMP + + CH VOUME - - Indicator ED SETTING UP COMPONENTS Perform the procedure for each component you own. At the end of each step 5, the remote control's processor will automatically assign the selected component's control functions to its own buttons, ready for your use. SETTING UP YOU 1. Turn on the television set and look up a setup code for your brand of television (codes are located at the back of the HT-5550 Owner's Manual). 2. On the remote control, press button B. MUTE INPUT MUTE TANSMIT Use Keypad To Enter Setup Codes HA 1 SPOTS 5 /DTS SU. JAZZ CUB 2 MONO MOVIE 6 OCK CONCET SEECT MATIX 6.1 ENTE- TAINMENT 3 4 MOVIE THEATE 1 MOVIE THEATE 2 7 8 STEEO CD AV MD/CD- D-/CB TUNE V-AUX SYSTEM SEEP 6CH INPUT 9 0 +10 ENTE EFFECT VC A B AMP EVE PESET/CH SET MENU TITE MENU - TEST ETUN EC SEECT A/B/C/D/E + DISPAY AUDIO Used to Change and Implement the Settings 3. Press using a ballpoint pen or similar object. The TANSMIT indicator ED will flash twice. DISC SKIP TANSMIT 4. Using the keypad, enter the four-digit setup code. The indicator ED will flash twice after your entry. If the ED did not flash twice, repeat steps 3 and 4. The YHT-700 Home Theater package includes a universal remote control. It comes pre-programmed with factory codes to control your HT-5550 receiver and most Yamaha audio components. To program other brands of components (i.e.,, VC, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer's codes (listed on the back pages of the HT-5550 Owner's Manual). NOTE: The universal remote control is designed to control most major brands of audio and video components. For other units, use the original remote control supplied with the product. ON 1. oad the supplied batteries into the remote control. 2. Aim the remote control at the receiver, press the SYSTEM button. 3. The receiver should turn on. HA 1 SPOTS 5 /DTS SU. 9 JAZZ CUB 2 MONO MOVIE 6 OCK CONCET MOVIE THEATE 1 SEECT MATIX 6.1 0 +10 ENTE- TAINMENT 3 4 MOVIE THEATE 2 7 8 STEEO ENTE EFFECT NOTE: If you wait more than 30 seconds during step 4, the process will be canceled. If this happens, start from Step 2. 5. To verify the code works, aim the remote control at the television set, press the button. The television set should turn off. If it doesn't respond, use another code for the same manufacturer and repeat steps 3 through 5. AV TANSMIT SYSTEM 10

POGAMMING THE UNIVESA EMOTE CONTO (CONTINUED) SETTING UP YOU CABE BOX (O DSS) 1. Turn on the cable box (or DSS) and look up a setup code for your brand of cable box (or DSS) (codes are located at the back of the HT-5550 Owner's Manual). 2. On the remote control, press D-/CB. CD AV MD/CD- TANSMIT TUNE SYSTEM SEEP SETTING UP OTHE COMPONENTS 1. Turn on the component (e.g., CD player, tape deck, or MD player) and look up a setup code for your brand of component. 2. On the remote control, press the desired component button (e.g., CD or MD/CD-). 3. Press using a ballpoint pen or similar object. The TANSMIT indicator ED will flash twice. VC D-/CB 3. Press using a ballpoint pen or similar object. The TANSMIT indicator ED will flash twice. 4. Using the keypad, enter the four-digit setup code. The indicator ED will flash twice after your entry. If the ED did not flash twice, repeat steps 3 and 4. 5. To verify the code works, aim the remote control at the cable box (or DSS), press D-/CB, and then press AV. The unit should turn off. If it doesn'trespond, use another code for the same manufacturer and repeat steps 3 through 5. SETTING UP YOU VC 1. Turn on the VC and look up a setup code for your brand of VC. 2. On the remote control, press VC. A V-AUX B 6CH INPUT AMP 4. 5. Using the keypad, enter the four-digit setup code. The indicator ED will flash twice after your entry. If the ED did not flash twice, repeat steps 3 and 4. To verify the code works, aim the remote control at the component, press the appropriate component button, and then press AV. The unit should turn off. If it doesn't respond, use another code for the same manufacturer and repeat steps 3 through 5. AV TANSMIT SYSTEM NOTE: Your component's original remote control must have a power On/Off function in order for this remote to control your component's power function. TANSMIT SYSTEM AV CD MD/CD- TUNE SEEP D-/CB V-AUX 6CH INPUT VC A B AMP 3. Press using a ballpoint pen or similar object. The TANSMIT indicator ED will flash twice. 4. Using the keypad, enter the four-digit setup code. The indicator ED will flash twice after your entry. If the ED did not flash twice, repeat steps 3 and 4. 5. To verify the code works, aim the remote control at the VC, press VC, and then press AV. The VC should turn off. If it doesn't respond, use another code for the same manufacturer and repeat steps 3 through 5. 11

OPEATING THE UNIVESA EMOTE CONTO OVEVIEW The universal remote control will control up to nine different types of components each of which becomes active when you press a selection ( except which has priority and function buttons are always active). We can only briefly describe some functions here, and we encourage you use the HT-5550 Owner's Manual to gain additional experience with this powerful unit. PAYING A CASSETTE 1. Aim the remote control at the HT-5550, press SYSTEM to turn the receiver on. Press VC as the input for the receiver. 2. Aim the remote control at the, press the to turn the television on. 3. Aim the remote control at the VC, press VC to select the component, and then press AV to turn the VC on. Put a tape in the VC, press (forward button) to start play. NOTE: At this point, the VC controls are assigned to the remote control, since VC was the last selected component. PAYING A 1. Aim the remote control at the HT-5550, press SYSTEM to turn the receiver on. Press as the input for the receiver. 2. Press and then press AV to turn the player on. NOTE: If the player is plugged into the switched outlet (on the back of the receiver) and its power switch AC was already engaged, the unit will come on each time the receiver is powered on. 3. oad a into the player. 4. Aim the remote control at the player, and press (forward button) to start play. NOTE: The player's controls are now assigned to the remote control buttons, since was the last selected component. ESETTING THE EMOTE CONTO TO FACTOY CODES You can reset the remote control to factory codes for all components or a desired component, as follows: ESETTING CODES FO A COMPONENTS 1. Press any component selector. 2. Press using a ballpoint pen or similar object. The TANSMIT indicator ED will flash twice. 3. Using the keypad, enter the code "9990". 4. The indicator ED will flash twice to confirm all codes have been reset to factory values. If the ED does not flash twice, repeat steps 1 through 3. ESETTING CODES FO A DESIED COMPONENT 1. Press a component selector button that matches the component you wish to reset to factory codes. 2. Press. The TANSMIT indicator ED will flash twice. 3. Using the keypad, enter the code "0000". 4. The indicator ED will flash twice to confirm all codes have been reset to factory values. If the ED does not flash twice, repeat steps 1 through 3. 5. For your convenience, the following reference chart lists the factory codes: Component Component Code Selector Button CD CD 0005 Yamaha MD/CD- MD 0024 Yamaha TUNE TUNE 0003 Yamaha 0098 Yamaha 2002 YAMAHA EECTONICS COPOATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (888) 435-7922 http://www.yamaha.com 12