CineMax Kit ASSEMBLY AND CALIBRATION www.cineversum.com Ref: T9003000 Rev: 01 Part. No.: R599766
Changes CineVERSUM provides this manual as is without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. CineVERSUM may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice. This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication. Copyright All right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of CineVERSUM. Guarantee CineVERSUM provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. CineVERSUM must be informed immediately in writing of any complaints. If the purchaser or third party caries out modifications or repairs on goods delivered by CineVERSUM, or if the goods are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by CineVERSUM either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer. Trademarks Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brands and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products of their manufactures. 2 R599766-2.35 Cinemax Kit
TABLE OF CONTENTS 1.0 2.35 Cinemax Kit... 4 1.1 Installing the Mounting Plate... 4 1.2 Cinemax prismatic Lens alignment... 5 Adjust the full screen picture... 5 Set the horizontal picture position into the screen... 6 Set the tilt and vertical position of the lens... 7 1.3 Install the Lens Cap... 8 2.0 Projector-side configuration... 8 2.1 Configure the 12V Trigger 2... 8 Connect your screen control device to the 12V Trigger 2 output... 8 Configure Initial Setup Menu -> Trigger 2 to THEATRE... 8 2.2 Configure the Anamorphic Aspect Ratios... 9 16:9 input: Aspect Ratio to Converted 16:9... 9 Cinemascope input: Aspect Ratio to Cinemascope... 9 2.3 Using the Remote Control Unit.... 10 Select the correct Aspect Ratio for each input... 10 [ASPECT] button behavior... 11 Quick Aspect Ratio change on the same input... 11 2.4 Using RS-232 protocole... 11 Communication Specifications... 11 Command Format... 12 Available Lengths and Commands... 12 3.0 Miscellaneous... 14 3.1 Dimensions... 14 3.2 Projection distances... 14 R599766-2.35 Cinemax Kit 3
1.0 2.35 CINEMAX KIT 1.0 2.35 CINEMAX KIT The 2.35 Cinemax Kit is a simple and versatile solution to operate a cinemascope experience using the Cinemax prismatic Lens. The Blackwing One features an exclusive THEATRE Mode for an easier screen masking control. The new THEATRE Mode features: 1.1 Integrated CIW system. Dedicated menu to program the 12V Trigger2 output to control your motorized screen mask. Direct access button on the Remote Control Unit to switch between Anamorphic modes. Installing the Mounting Plate a)use the 3x M6x15 screws to fix the plate at the bottom of the projector. M6x15 screews b) Use the 4x M5x7 screws to fix the lens support. to the fixing plate and the 2 round head screws to fix the Cinemax prismatic Lens in front of the projector lens. M5x7 4 round head screws R599766-2.35 Cinemax Kit
1.0 2.35 CINEMAX KIT 1.2 Cinemax prismatic Lens alignment Adjust the full screen picture To obtain a 2.35 picture, you can use a 16:9 picture set to Full Screen aspect ratio. The picture must fulfill the screen. These adjustment are made by using the Zoom and the vertical shift and horizontal shift of the projector. When the picture position is correct, adjust the picture focus. ZOOM ZOOM Adjust the Zoom and the Lens Offset until the picture fulfills the screen. R599766-2.35 Cinemax Kit 5
1.0 2.35 CINEMAX KIT S FOCU Adjust the picture Focus Set the horizontal picture position into the screen A A To adjust the horizontal position of the picture into the screen, release the 4 screws (A) and turn the Anamorphic Lens left or right to obtain a centered 2.35 picture. Tighten the screws when completed. This adjustment can also be achieved by using the Horizontal Lens Offset. The Horizontal Lens Offset should be used only for fine adjustments. The use of the maximum 30% horizontal offset may decrease the overall picture quality.. 6 R599766-2.35 Cinemax Kit
1.0 2.35 CINEMAX KIT Set the tilt and vertical position of the lens B B Adjust the Anamorphic Lens tilt and vertical position, so that the projector light beam is centered into the Anamorphic Lens and to compensate the upper and lower pincushion effects. Tighten the 2 screws (B) when completed. You may obtain a residual pincushion effect at the screen when using a throw ratio between 1.5:1 and 1.8:1 or a projection distance shorter than 5 meters. It is recommended to install your projector at a minimum distance of 5 meters from the screen and using 1.8:1 or higher throw ratio with a flat screen. Otherwise, the use of a curved 2.35 screen is recommended. R599766-2.35 Cinemax Kit 7
2.0 PROJECTOR-SIDE CONFIGURATION 1.3 Install the Lens Cap C C Install the lens Cap and fix it using the 2 screws (C). 2.0 PROJECTOR-SIDE CONFIGURATION 2.1 Configure the 12V Trigger 2 Connect your screen control device to the 12V Trigger 2 output 12V Trigger 1 12V Trigger 2 The 12V Trigger 2 output can control the screen masking Configure Initial Setup Menu Trigger 2 to THEATRE Screen mask Control The Initial Setup Trigger 2 menu determines the Trigger 2 output located in the panel input of the Blackwing One this is a global parameter (for all inputs): ON: the 12V Trigger 2 is always active when the projector is switched ON. OFF: the 12V Trigger 2 is always switched Off. THEATRE: this option turns ON the Trigger 2 output when the aspect ratio is set to Cinemascope. 8 R599766-2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION 2.2 Configure the Anamorphic Aspect Ratios 16:9 input: Aspect Ratio to Converted 16:9 When you select a 16:9 input, choose the Converted 16:9 aspect ratio, and configure the Aspect Ratio between 1.30 and 1.40 to obtain the correct geometry. Select Converted 16:9 in the OSD Menu Input Signal Aspect Ratio Converted 16:9 Then choose the correct Aspect Ratio between 1.30 and 1.40 in the menu Input Signal Converted 16:9 Aspect Ratio 1.33 so that the 16:9 picture is letter-boxed into the 2.35 screen. You can rise the Aspect Ratio up to 1.78 to reduce the black bars on the left and the right of the screen but the picture may be horizontally stretched. 1.33x 1.60x You can rise the Aspect Ratio Mode 2from 1.30 up to 1.78 to reduce the black bars. Cinemascope input: Aspect Ratio to Cinemascope When selecting a wide format input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than 16:9, you can see black bars on the top and the bottom of the screen. Select the Anamorphic Mode1 for this input in the Input Signal Aspect Ratio Cinemascope. Then choose the correct Anamorphic Aspect Ratio between 2.30 and 2.50 in the menu Input Signal Cinemascope Aspect Ratio 2.37 so that the black bars disappear and the active picture fulfills the screen. 2.34x 2.37x Adjust the Aspect Ratio Mode1 between 2.30 and 2.50 to eliminate the black bars. You can lower the Aspect Ratio Mode1 down to 1.78 if you plan to watch an original 16:9 program with upper and lower picture portion lost. The picture may be horizontally stretched. R599766-2.35 Cinemax Kit 9
2.0 PROJECTOR-SIDE CONFIGURATION 2.3 Using the Remote Control Unit. Select active input Select the correct Aspect Ratio Blackwing One RCU and quick access features Select the correct Aspect Ratio for each input On the first install, configure the desired Aspect Ratio for each input. By example, a TV source on HDMI1 will use Converted 16:9 (16:9 native format) and a Blu-Ray player on HDMI2 will use Cinemascope (Cinemascope format). Each input retains the last Aspect Ratio applied, so that selecting a different input with the RCU automatically choose the correct Aspect Ratio. 10 R599766-2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION [ASPECT] button behavior The [ASPECT] button triggers the 5 aspect ratio modes. Once a given aspect ratio is validated, the order of the next aspect ratio is reversed so that the previous aspect ratio becomes the next aspect ratio as described below. Full Screen Standard Cinemascope The Cinemax Kit uses Converted 16:9 and and Cinemascope modes. Virtual Wide Converted 16:9 When you press sequentially the [ASPECT] button, the aspect mode rotation goes clock-wise. Press [ESC] or wait 15 seconds until the message fades out to confirm selection. Next time that you will press the [ASPECT] button, the rotation order is reversed. This behavior ensures a fast switch between two particular aspect ratios. Quick Aspect Ratio change on the same input The Remote Control Unit can be used to quickly switch the aspect ratio by pressing twice the [ASPECT] button to switch forth and backward from Cinemascope to Converted 16:9 as described below: Full Screen on 2.35 screen Converted 16:9 Cinemascope 16:9 picture 2.35:1 picture When the source automatically switches format...... press twice [ASPECT] button on the Remote Control Unit 2.4 Using RS-232 protocole Communication Specifications Control of 2.35 THEATRE Concept is possible using a computer or automation device connected with a RS-232 straight cable connected to the Blackwing One (male - female D-sub 9 pins cable). Communication specifications R599766-2.35 Cinemax Kit 11
2.0 PROJECTOR-SIDE CONFIGURATION for this unit are as follows: Baud Rate Data Format Character Length Parity Stop Bit X on/off Flow Control 115200 bps Binary 8 bits None 1 bit None None Command Format When sending a command to this unit, use the following data format: Header Length Command EoD 1 or 3 bytes 0 or 1 byte at least 1 byte 1 byte Header Length Command EoD (00h) for power ON command, (77h 88h 99h) for other commands. The total bytes of Length and Command Designates the command Designates the end of the data. Fixed to (FFh) Available Lengths and Commands Command Header (00h) Length Command Description Power ON None 01h If the projector is in standby mode, this command switch the unit ON. Command Header (77h 88h 99h) Length Command Description Power OFF 03h 02h 01hh If the projector is powered ON, this command switch this unit into Standby Mode. (Directly OFF) Switch Input 03h 02h 02h Switch active input to Video (Composite) 02h 03h Switch active input to S-Video 02h 04h Switch active input to Component 02h 05h Switch active input to VGA (sd15) 02h 06h Switch active input to HDMI 1 02h 07h Switch active input to HDMI 2 Blanking 03h 02h 08h Toggle projector Blanking ON 02h 09h Toggle projector Blanking OFF Keypad 03h 01h 01h MENU: Toggle OSD Menu ON and OFF 01h 02h UP: Uses as up function key for navigation 01h 03h DOWN: Uses as down function key for navigation 01h 04h LEFT: Uses as left function key for navigation 01h 05h RIGHT: Uses as right function key for navigation 01h 06h ENTER: Selects menu item or the next menu 01h 07h EXIT: exits the current menu to the previous one. 01h 08h SOURCE: Switch input source. 01h 09h Power OFF: Turn off the projector (send twice) 12V Trigger #2 03h 03h 01h Switch the trigger to ON. 03h 02h Switch the trigger to OFF 03h 03h Switch the trigger to THEATRE 12 R599766-2.35 Cinemax Kit
2.0 PROJECTOR-SIDE CONFIGURATION Aspect Ratio 03h 03h 04h Switch aspect ratio to Standard 03h 05h Switch aspect ratio to Full Screen 03h 06h Switch aspect ratio to Cinemascope 03h 07h Switch aspect ratio to Converted 16:9 03h 08h Switch aspect ratio to Virtual Wide Lens Aperture 03h 03h 09h Open one level up the Lens Aperture 03h 0Ah Close on level down the Lens Aperture Picture Mode 03h 04h 01h Switch picture mode to Standard 04h 02h Switch picture mode to Dynamic 04h 03h Switch picture mode to Theater 04h 04h Switch picture mode to User 1 04h 05h Switch picture mode to User 2 04h 06h Switch picture mode to User 3 Picture Adjust 03h 05h 01h Show brightness slider (use left or right to modify) 05h 02h Show contrast slider 05h 03h Show colour slider 05h 04h Show hue slider 05h 05h Show sharpness slider 05h 06h Show black level slider 05h 07h Show white level slider Colour Temperature 03h 06h 01h Switch colour temperature to Low 06h 02h Switch colour temperature to medium 06h 03h Switch colour temperature to High 06h 04h Switch colour temperature to User 1 06h 05h Switch colour temperature to User 2 06h 06h Switch colour temperature to User 3 06h 07h Switch colour temperature to Medium-high Gamma 03h 07h 01h Switch gamma to Gamma 1 07h 02h Switch gamma to Gamma 2 07h 03h Switch gamma to Gamma 3 07h 04h Switch gamma to Gamma 4 07h 05h Switch gamma to User 1 07h 06h Switch gamma to User 2 07h 07h Switch gamma to User 3 Scaling features 03h 08h 01h Set detail enhancement to Off 08h 02h Set detail enhancement to Low 08h 03h Set detail enhancement to Medium 08h 04h Set detail enhancement to High Temporal Noise 03h 08h 05h Set TNR to Off 08h 06h Set TNR to Low 08h 07h Set TNR to Medium 08h 08h Set TNR to High Mosquito Noise 03h 09h 01h Set MNR to Off 09h 02h Set MNR to Low 09h 03h Set MNR to Medium 09h 04h Set MNR to High Block Artifact 03h 09h 05h Set BAR to Off 09h 06h Set BAR to On Reset to default 03h 0Ah 01h Reset settings to default value Examples You want to... Command to send Switch the projector ON 00h 01h FFh Switch the projector OFF 77h 88h 99h 03h 02h 01h FFh Switch the projector OFF with OSD confirmation 77h 88h 99h 03h 01h 09h FFh R599766-2.35 Cinemax Kit 13
3.0 MISCELLANEOUS Switch Aspcet Ratio mode to Cinemascope Switch Aspcet Ratio mode to Converted 16:9 77h 88h 99h 03h 03h 06h FFh 77h 88h 99h 03h 03h 07h FFh 3.0 MISCELLANEOUS 3.1 Dimensions 199 mm 7.8 800mm 31.5 800mm 31.5 530 mm 530 mm 20.9 20.9 3.2 Projection distances Projection Screen Size Diagonal size (Aspect Ratio 2.35:1) Projection Screen Base size Projection Screen Height Blackwing One Projecting Distance minimum - maximum 107" (2720 mm) 98.4" (2500 mm) 41.7" (1060 mm) 3000 mm - 4100 mm 128" (3250 mm) 118.1" (3000 mm) 50.4" (1280 mm) 3500 mm - 4900 mm 149" (3780 mm) 137.8" (3500 mm) 58.7" (1490 mm) 4010 mm - 5700 mm 170" (4520 mm) 157.5" (4000 mm) 66.9" (1700 mm) 4600 mm - 6500 mm 200" (5080 mm) 184.3" (4680 mm) 77.5" (1970 mm) 5400 mm - 7600 mm 14 R599766-2.35 Cinemax Kit
Contact Information: TEC - CineVERSUM 7, rue La CAILLE, 75017 Paris - FRANCE Web: www.cineversum.com
Contact information TEC - CineVERSUM 7, rue La Caille, 75017 Paris, France www.cineversum.com Part. No. R599766