HD, SD SDI VBI/VANC encoder A Synapse product COPYRIGHT 2016 AXON DIGITAL DESIGN BV ALL RIGHTS RESERVED NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY FORM WITHOUT THE PERMISSION OF AXON DIGITAL DESIGN BV.
Block schematic & I/O panel HD/SD-SDI OUTPUT HD/SD-SDI IN 1 EQ CUE TONE DECODER TO TRIGGER SUBTITLES VBI/VANC DATA INSERTER WSS-VI- S2016 INSERTI ON ACTIVE VIDEO EMBEDDED AUDIO ANC BYPASS HD/SD-SDI OUTPUT ETHERNET PROCESSOR ENCODER CVBS PREVIEW CVBS OUTPUT RACK CONTROLLER INTERNAL SYNAPSE BUS BPH04 BHX04 HD/SD SDI INPUT (OPTIONAL FIBER INPUT) HD/SD SDI PREVIEW OUTPUT HD/SD SDI PROCESSED OUTPUT 1 relay bypass HD/SD SDI PROCESSED OUTPUT 2 (OPTIONAL FIBER OUTPUT) CVBS PREVIEW OUTPUT ETHERNET GPI INPUT
Features The is a standalone card that enables quick and easy insertion of subtitles and other data onto a program feed. This card will typically be used in applications where you need to trigger subtitling on a remote location by GPI. This is an easy way to have your control embedded in the video. This also assures the users the trigger is correct timed in comparison with the video. This product will be used for triggering of local subtitle insertion. A head end can send one program and enables the local stations to insert their own regional subtitles. Cost effective and space saving solution VANC/VBI subtitle and ancillary data insertion SD and HD-SDI compatible Formats: 1080i/50 625/50 Inserts incoming data generated in NEWFOR protocol in a parallel WST-B in SD format or OP47 in HD Support for two independent NEWFOR streams Bypass functionality when no Ethernet activity is detected Ability to Clear-Caption in the event of a hanging caption Triggered through embedded cues (Packet 31) AFD insertion WSS/VI S2016 Ethernet connector for data input Locks to SDI input CVBS output (valid for SD sources only) Full control and status monitoring through the front panel of the SFR04/SFR08/SFR18 frame and the Ethernet port (ACP) Optional 1 fiber input (replacing 1 SDI input) or 1 fiber output (replacing 1 SDI output) on I/O panel Applications The will typically be used in applications where Teletext subtitling is required on the program stream as part of the play out process. Generally this will be for live captioning where the program material is not available in time for the captions to be pre-prepared and added to the program material as part of the production process. The subtitle data stream will be generated by a third party product. This needs to be NEWFOR protocol.
Ordering information Module: : HD Caption and Teletext encoder with monitor outputs I/O: BPH04_: I/O-panel for Relay bypass I/O: BHX04_: I/O-panel for with relay bypass Fiber outputs: BPH04T_FC/PC_: I/O-panel for with fiber transmitter on FC/PC BPH04T_SC_: I/O-panel for with fiber transmitter on SC Fiber inputs: BPH04R_FC/PC_: I/O-panel for with fiber receiver on FC/PC BPH04R_SC_: I/O-panel for with fiber receiver on SC
Specifications SD/HD Serial Video Input Nunber of Inputs 1 625/50 or 525/59.94 SMPTE 259M-C (270Mb/s) with SMPTE 272M embedded audio SMPTE 292M (1.5Gb/s), SMPTE 260M, SMPTE 274M, SMPTE 296M, SMPTE 349M 1080i/59.94, 1080i/50, 720p/59.94, 720p/50 Equalization Automatic to 100m @ 1.5Gb/s with Belden 1694A or equivalent cable. Serial Video Output Number of Outputs DC Offset Rise and Fall Time Overshoot Wideband Jitter 3 (1 preview and 2 processed) 800mV nominal 0V ±0.5V 750ps nominal for SD < 10% of amplitude > 15dB up to 270MHz < 0.2UI Analog Video Output PAL (ITU624-4) or NTSC (SMPTE 170M), composite Number of Outputs 1 BNC 1V nominal Impedance 75 Ohms > 35dB to 10MHz Frequency Response 0.5dB to 4.5 MHz Differential Gain < 0.6% Differential Phase < 0.7 SNR > 75dB Ethernet 10Base-T, 100Base-Tx IEEE 802.3 8P8C Protocol NEWFOR Reference Video Input PAL (ITU624-4), NTSC (SMPTE 170M) Number of Inputs 2 on SFR18, 2 on SFR08, 1 on SFR04 BNC 1V nominal Impedance High impedance, with loop for termination > 25dB to 10MHz World System Teletext WST-B ETSI EN 300 706 V1.2.1 (2003-04) Packet 31 Independent Data Lines (IDL), ETSI EN 300 708 V1.2.1 (2002-12) OP47 OP47-SDP (Issue 4, December 2008) Miscellaneous Weight Approx. 250g Operating Temperature 0 C to +50 C Dimensions 137 x 296 x 20 mm (HxWxD) Electrical Voltage +24V to +30V Power <10 Watts