TLE8251V. 1 Overview. High Speed CAN Transceiver with Bus Wake-up

High Speed CAN Transceiver wih Bus Wake-up 1 Overview Feaures Complian o ISO11898-2: 2003 and ISO11898-5: 2007 Wide common mode range for elecromagneic immuniy (EMI) Very low elecromagneic emission (EME) Excellen ESD robusness Guaraneed and improved loop delay symmery o suppor CAN FD daa frames up o 2 MBi/s for Japanese OEMs V IO inpu for volage adapion o he microconroller supply Exended supply range on V CC and V IO supply CAN shor circui proof o ground, baery and V CC TxD ime-ou funcion Low CAN bus leakage curren in power-down sae Overemperaure proecion Proeced agains auomoive ransiens Sand-by mode wih remoe wake-up funcion Wake-up indicaion on he RxD oupu Transmier supply V CC can be urned off in sand-by mode Green Produc (RoHS complian) AEC Qualified Cerified according o laes VeLIO (Vehicle LAN Ineroperabiliy & Opimizaion) es requiremens for he Japanese marke Applicaions Gaeway Modules Body Conrol Modules (BCMs) Elecric Power seering Baery Managemen Sysems Cluser and Lighing Conrol Modules Descripion The TLE8251VSJ is a ransceiver designed for HS CAN neworks in auomoive and indusrial applicaions. As an inerface beween he physical bus layer and he CAN proocol conroller, he TLE8251VSJ drives he Daa Shee 1 Rev. 1.0 www.infineon.com/ransceiver

High Speed CAN Transceiver wih Bus Wake-up Overview signals o he bus and proecs he microconroller agains inerferences generaed wihin he nework. Based on he high symmery of he CANH and CANL signals, he TLE8251VSJ provides a very low level of elecromagneic emission (EME) wihin a wide frequency range. The TLE8251VSJ fulfills or exceeds he requiremens of he ISO11898-2. The TLE8251VSJ provides a digial supply inpu V IO and a sand-by mode. I is designed o fulfill he enhanced physical layer requiremens for CAN FD and suppors daa raes up o 2 MBi/s. On he basis of a very low leakage curren on he HS CAN bus inerface he TLE8251VSJ provides an excellen passive behavior in power-down sae. These and oher feaures make he TLE8251VSJ excepionally suiable for mixed supply HS CAN neworks. Based on he Infineon Smar Power Technology SPT, he TLE8251VSJ provides excellen ESD immuniy ogeher wih a very high elecromagneic immuniy (EMI). The TLE8251VSJ and he Infineon SPT echnology are AEC qualified and ailored o wihsand he harsh condiions of he auomoive environmen. Two differen operaing modes, addiional fail-safe feaures like a TxD ime-ou and he opimized oupu slew raes on he CANH and CANL signals make he TLE8251VSJ he ideal choice for large HS CAN neworks wih high daa ransmission raes. Type Package Marking TLE8251VSJ PG-DSO-8 8251V Daa Shee 2 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Table of Conens 1 Overview................................................................................. 1 Table of Conens......................................................................... 3 2 Block Diagram............................................................................ 4 3 Pin Configuraion......................................................................... 5 3.1 Pin Assignmen........................................................................... 5 3.2 Pin Definiions............................................................................ 5 4 Funcional Descripion.................................................................... 6 4.1 High Speed CAN Physical Layer............................................................ 6 4.2 Modes of Operaion....................................................................... 8 4.2.1 Normal-operaing Mode................................................................. 8 4.2.2 Sand-by Mode......................................................................... 8 4.3 Power-up and Undervolage Condiion..................................................... 9 4.3.1 Power-down Sae..................................................................... 10 4.3.2 Forced Sand-by Mode................................................................. 10 4.3.3 Power-up............................................................................. 10 4.3.4 Undervolage on he Digial Supply V IO................................................... 11 4.3.5 Undervolage on he Transmier Supply V CC.............................................. 12 4.3.6 Volage Adapion o he Microconroller Supply........................................... 12 4.4 Remoe Wake-up........................................................................ 13 5 Fail Safe Funcions....................................................................... 14 5.1 Shor Circui Proecion.................................................................. 14 5.2 Unconneced Logic Pins.................................................................. 14 5.3 TxD Time-ou Funcion................................................................... 14 5.4 Overemperaure Proecion.............................................................. 15 5.5 Delay Time for Mode Change.............................................................. 15 6 General Produc Characerisics........................................................... 16 6.1 Absolue Maximum Raings............................................................... 16 6.2 Funcional Range........................................................................ 17 6.3 Thermal Resisance...................................................................... 17 7 Elecrical Characerisics................................................................. 18 7.1 Funcional Device Characerisics......................................................... 18 7.2 Diagrams............................................................................... 24 8 Applicaion Informaion.................................................................. 26 8.1 ESD Robusness according o IEC61000-4-2................................................ 26 8.2 Applicaion Example..................................................................... 27 8.3 Examples for Mode Changes.............................................................. 27 8.3.1 Mode Change o Sand-by Mode during a dominan Bus Signal............................. 29 8.3.2 Mode Change from Sand-by Mode o Normal-operaing Mode............................. 30 8.3.2.1 Mode Change while he TxD Signal is low............................................. 30 8.3.2.2 Mode Change while he Bus Signal is dominan......................................... 31 8.4 Furher Applicaion Informaion.......................................................... 32 9 Package Ouline......................................................................... 33 10 Revision Hisory......................................................................... 34 Daa Shee 3 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Block Diagram 2 Block Diagram 3 5 V CC V IO Transmier CANH 7 Driver Timeou 1 TxD CANL 6 Tempproecion Mode conrol 8 STB Receiver Normal-mode receiver Mux 4 RxD Wake-logic & filer Low-power receiver V IO V CC /2 = Bus-biasing GND 2 Figure 1 Funcional block diagram Daa Shee 4 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Pin Configuraion 3 Pin Configuraion 3.1 Pin Assignmen TxD 1 8 STB GND 2 7 CANH V CC 3 6 CANL RxD 4 5 V IO Figure 2 Pin configuraion 3.2 Pin Definiions Table 1 Pin definiions and funcions Pin No. Symbol Funcion 1 TxD Transmi Daa Inpu; inernal pull-up o V IO, low for dominan sae. 2 GND Ground 3 V CC Transmier Supply Volage; 100 nf decoupling capacior o GND required, V CC can be urned off in sand-by mode. 4 RxD Receive Daa Oupu; low in dominan sae. 5 V IO Digial Supply Volage; supply volage inpu o adap he logical inpu and oupu volage levels of he ransceiver o he microconroller supply, supply for he low-power receiver, 100 nf decoupling capacior o GND required. 6 CANL CAN Bus Low Level I/O; low in dominan sae. 7 CANH CAN Bus High Level I/O; high in dominan sae. 8 STB Sand-by Inpu; inernal pull-up o V IO, low for normal-operaing mode. Daa Shee 5 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4 Funcional Descripion HS CAN is a serial bus sysem ha connecs microconrollers, sensors and acuaors for real-ime conrol applicaions. The use of he Conroller Area Nework (abbreviaed CAN) wihin road vehicles is described by he inernaional sandard ISO 11898. According o he 7-layer OSI reference model he physical layer of a HS CAN bus sysem specifies he daa ransmission from one CAN node o all oher available CAN nodes wihin he nework. The physical layer specificaion of a CAN bus sysem includes all elecrical and mechanical specificaions of a CAN nework. The CAN ransceiver is par of he physical layer specificaion. Several differen physical layer sandards of CAN neworks have been developed in recen years. The TLE8251VSJ is a High Speed CAN ransceiver wih a dedicaed bus wake-up funcion and defined by he inernaional sandard ISO 11898-5. 4.1 High Speed CAN Physical Layer TxD CANH CANL VIO VCC VIO = Digial supply volage VCC = Transmier supply volage TxD = Transmi daa inpu from he microconroller RxD = Receive daa oupu o he microconroller CANH = Bus level on he CANH inpu/oupu CANL = Bus level on he CANL inpu/oupu VDiff = Differenial volage beween CANH and CANL VDiff = VCANH VCANL VDiff VCC dominan receiver hreshold recessive receiver hreshold RxD VIO Loop(H,L) Loop(L,H) Figure 3 High speed CAN bus signals and logic signals Daa Shee 6 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion The TLE8251VSJ is a High-Speed CAN ransceiver, operaing as an inerface beween he CAN conroller and he physical bus medium. A HS CAN nework is a wo wire, differenial nework which allows daa ransmission raes for CAN FD frames up o 2 MBi/s. Characerisic for HS CAN neworks are he wo signal saes on he HS CAN bus: dominan and recessive (see Figure 3). V CC, V IO and GND are he supply pins for he TLE8251VSJ. The pins CANH and CANL are he inerface o he HS CAN bus and operae in boh direcions, as an inpu and as an oupu. RxD and TxD pins are he inerface o he CAN conroller, he TxD pin is an inpu pin and he RxD pin is an oupu pin. The STB pin is he inpu pin for mode selecion (see Figure 4). By seing he TxD inpu pin o logical low he ransmier of he TLE8251VSJ drives a dominan signal o he CANH and CANL pins. Seing TxD inpu o logical high urns off he ransmier and he oupu volage on CANH and CANL discharges owards he recessive level. The recessive oupu volage is provided by he bus biasing (see Figure 1). The oupu of he ransmier is considered o be dominan, when he volage difference beween CANH and CANL is greaer han 1.5 V (V Diff = V CANH - V CANL ). Parallel o he ransmier he normal-mode receiver moniors he signal on he CANH and CANL pins and indicaes i on he RxD oupu pin. A dominan signal on he CANH and CANL pins ses he RxD oupu pin o logical low, vice versa a recessive signal ses he RxD oupu o logical high. The normal-mode receiver considers a volage difference (V Diff ) beween CANH and CANL above 0.9 V as dominan and below 0.5 V as recessive. To conform wih HS CAN feaures, like he bi o bi arbiraion, he signal on he RxD oupu has o follow he signal on he TxD inpu wihin a defined loop delay Loop 255 ns. The hresholds of he digial inpus (TxD and STB) and of he RxD oupu volage are adaped o he digial power supply V IO. Daa Shee 7 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.2 Modes of Operaion V CC = don care V IO > V IO(UV,R) sand-by mode STB = 1 STB = 0 STB = 1 V CC > V CC(UV,R) V IO > V IO(UV,R) normal-operaing mode STB = 0 Figure 4 Mode sae diagram 4.2.1 Normal-operaing Mode In normal-operaing mode he ransmier and he receiver of he HS CAN ransceiver TLE8251VSJ are acive (see Figure 1). The HS CAN ransceiver sends he serial daa sream on he TxD inpu pin o he CAN bus. The daa on he CAN bus is displayed a he RxD pin simulaneously. A logical low signal on he STB pin selecs he normal-operaing mode, while he ransceiver is supplied by V CC and V IO (see Table 2 for deails). 4.2.2 Sand-by Mode The sand-by mode is an idle mode of he TLE8251VSJ wih opimized power consumpion. In sand-by mode he ransmier and he normal-mode receiver are urned off. The TLE8251VSJ canno send any daa o he CAN bus nor receive any daa from he CAN bus. The low-power receiver is conneced o he bus lines. Wake-up signals are indicaed on he RxD oupu pin. An addiional filer, implemened inside he low-power receiver, ensures ha only dominan and recessive signals on he CAN bus, which are longer han he CAN aciviy filer ime Filer, are indicaed a he RxD oupu pin (see Figure 8). A logical high signal on he STB pin selecs he sand-by mode, while he ransceiver is supplied by he digial supply V IO (see Table 2 for deails). In sand-by mode he bus inpu pins are biased o GND via he receiver inpu resisors R i. Undervolage deecion on he ransmier supply V CC is urned off, allowing o swich off he V CC supply in sand-by mode. Daa Shee 8 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.3 Power-up and Undervolage Condiion When deecing an undervolage even, eiher on he ransmier supply V CC or he digial supply V IO, he ransceiver TLE8251VSJ changes he mode of operaion. Turning off he digial power supply V IO, he ransceiver powers down and remains in he power-down sae. While swiching off he ransmier supply V CC, he ransceiver eiher changes o he forced sand-by mode, or remains in sand-by mode (deails see Figure 5). STB V CC V IO X power-down sae X V IO on V CC on STB 0 off V IO on V CC X STB 1 V IO on V CC off STB 0 normal-operaing mode STB V CC V IO 0 on on V IO on V CC X STB 1 V IO on V CC on STB 0 sand-by mode STB V CC V IO 1 X on V IO on V CC off STB 0 V IO on V CC on STB 0 forced sand-by mode STB V CC V IO 0 off on V IO on V CC X STB 1 Figure 5 Power-up and undervolage Table 2 Modes of operaion Mode STB V IO V CC Bus Bias Transmier Normal-mode Low-power Receiver Receiver Normal-operaing low on on V CC /2 on on off Sand-by high on X GND off off on Forced sand-by low on off GND off off on Power-down sae X 1) off X floaing off off off 1) X : Don care Daa Shee 9 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.3.1 Power-down Sae Independen of he ransmier supply V CC and of he STB inpu pin, he TLE8251VSJ is in power-down sae when he digial supply volage V IO is urned off (see Figure 5). In power-down sae he inpu resisors of he receiver are disconneced from he bus biasing V CC /2. The CANH and CANL bus inerface of he TLE8251VSJ is floaing and acs as a high-impedance inpu wih a very low leakage curren. The high-ohmic inpu does no influence he recessive level of he CAN nework and allows an opimized EME performance of he enire HS CAN nework (see also Table 2). 4.3.2 Forced Sand-by Mode The forced sand-by mode is a fail-safe mode o avoid any disurbance on he HS CAN bus during loss of he ransmier supply V CC. In forced sand-by mode, he ransmier and he normal-mode receiver are urned off and herefore he ransceiver TLE8251VSJ can no disurb he bus media. Similar o sand-by mode, he low-power receiver is conneced o he bus lines and wake-up signals on he CAN bus are indicaed a he RxD oupu pin (see Figure 8). In forced sand-by mode he bus is also biased o GND (deails see Table 2) via he receiver inpu resisors. Forced sand-by mode can only be enered when he ransmier supply V CC is no available, eiher by powering up he digial supply V IO only or by urning off he ransmier supply in normal-operaing mode. While he ransceiver TLE8251VSJ is in forced sand-by mode, swiching he STB inpu pin o logical high riggers a mode change o sand-by mode (see Figure 5). 4.3.3 Power-up The HS CAN ransceiver TLE8251VSJ powers up if a leas he digial supply V IO is conneced o he device. By defaul he device powers up in sand-by mode, due o he inernal pull-up resisor on he STB pin o V IO. In case he device is o power-up o normal-operaing mode, he STB pin needs o be pulled acive o logical low and he supplies V IO and V CC have o be conneced. By supplying only he digial power supply V IO he TLE8251VSJ powers up eiher in forced sand-by mode or sand-by mode, depending on he signal of he STB inpu pin (see Figure 5). Daa Shee 10 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.3.4 Undervolage on he Digial Supply V IO If he volage on V IO supply inpu falls below he hreshold V IO < V IO(UV,F), he ransceiver TLE8251VSJ powers down and changes o power-down sae. Undervolage deecion on he digial supply V IO has he highes prioriy. I is independen of he ransmier supply V CC and also independen of he currenly seleced operaing mode. Any undervolage even on V IO powers down he TLE8251VSJ. ransmier supply volage VCC = don care VIO VIO undervolage monior VIO(UV,F) hyseresis VIO(UV,H) VIO undervolage monior VIO(UV,R) Delay(UV) delay ime undervolage any mode of operaion power-down sae sand-by mode STB X = don care high due he inernal pull-up resisor 1) 1) assuming no exernal signal applied Figure 6 Undervolage on he digial supply V IO Daa Shee 11 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.3.5 Undervolage on he Transmier Supply V CC In case he ransmier supply V CC falls below he hreshold V CC < V CC(UV,F), he ransceiver TLE8251VSJ changes he mode of operaion o forced sand-by mode. The ransmier and also he normal-mode receiver of he TLE8251VSJ are powered by he V CC supply. In case of insufficien V CC supply, he TLE8251VSJ can neiher ransmi he CANH and CANL signals correcly o he bus, nor can i receive hem properly. Therefore he TLE8251VSJ blocks he ransmier and he receiver in forced sand-by mode. The low-power receiver is acive in forced sand-by mode (see Figure 7). Undervolage deecion on he ransmier supply V CC is only acive in normal-operaing mode (see Figure 5). digial supply volage VIO = on VCC VCC undervolage monior VCC(UV,F) hyseresis VCC(UV,H) VCC undervolage monior VCC(UV,R) Delay(UV) delay ime undervolage normal-operaing mode forced sand-by mode normal-operaing mode STB Assuming he STB remains low. The low signal is driven by he exernal microconroller Figure 7 Undervolage on he ransmier supply V CC 4.3.6 Volage Adapion o he Microconroller Supply The HS CAN ransceiver TLE8251VSJ has wo differen power supplies, V CC and V IO. The power supply V CC supplies he ransmier and he normal-mode receiver. The power supply V IO supplies he digial inpu and oupu buffers, he low-power receiver and he wake-up logic. I is also he main power domain for he inernal logic. To adjus he digial inpu and oupu levels of he TLE8251VSJ o he I/O levels of he exernal microconroller, connec he power supply V IO o he microconroller I/O supply volage (see Figure 14). Noe: In case he digial supply volage V IO is no required in he applicaion, connec he digial supply volage V IO o he ransmier supply V CC. Daa Shee 12 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Funcional Descripion 4.4 Remoe Wake-up The TLE8251VSJ has a remoe wake-up feaure, also called bus wake-up feaure. In boh sand-by mode and forced sand-by mode, he low-power receiver moniors he aciviy on he CAN bus and in case i deecs a wake-up signal, he TLE8251VSJ indicaes he wake-up signal on he RxD oupu pin. While enering sand-by mode, he RxD oupu pin is se o logical high, regardless of he signal on he CAN bus. The low-power receiver of he TLE8251VSJ requires a signal change from recessive o dominan on he CAN bus before he RxD oupu is enabled o follow he signals on he HS CAN bus. HS CAN bus signals, dominan or recessive, wih a pulse widh above he CAN aciviy filer ime > Filer are indicaed on he RxD oupu pin. Gliches wih a pulse widh below he CAN aciviy filer ime < Filer are ignored and no considered a valid wake-up signal. The RxD oupu reacs wihin he reacion ime WU_Rec afer deecing a wake-up signal (see Figure 8). Noe: A wake-up even on he CAN bus is only indicaed on he RxD oupu, no auomaic change of he operaing mode is applied. To ener normal-operaing mode, he exernal microconroller needs o change he signal on he STB pin. The wake-up logic is supplied by he power supply V IO (see Figure 1). In case he TLE8251VSJ is in sand-by mode he power supply V CC can be urned off, while he TLE8251VSJ is sill able o deec a wake-up signal on he HS CAN bus (see also Figure 4). VDiff = VCANH - VCANL < Filer = Filer = WU_Rec = Filer = WU_Rec VDiff 1.15V 1.15 V 0.4V 0.4 V RxD 0.7 x VIO 0.3 x VIO STB Figure 8 Wake-up paern Daa Shee 13 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Fail Safe Funcions 5 Fail Safe Funcions 5.1 Shor Circui Proecion The CANH and CANL bus oupus are shor circui proof, eiher agains GND or a posiive supply volage. A curren limiing circui proecs he ransceiver agains damage. If he device is heaing up due o a coninuous shor on he CANH or CANL, he inernal overemperaure proecion swiches off he bus ransmier. 5.2 Unconneced Logic Pins All logic inpu pins have an inernal pull-up resisor o V IO. In case V IO supply is acivaed and he logic pins are open, he TLE8251VSJ eners sand-by mode by defaul. In sand-by mode he ransmier of he TLE8251VSJ is disabled, he bus bias is urned off and he inpu resisors of CANH and CANL are conneced o GND. 5.3 TxD Time-ou Funcion The TxD ime-ou feaure proecs he CAN bus agains permanen blocking in case he logical signal on he TxD pin is coninuously low. A coninuous low signal on he TxD pin migh have is roo cause in a lockedup microconroller or in a shor circui on he prined circui board, for example. In normal-operaing mode, a logical low signal on he TxD pin for he ime > TxD enables he TxD ime-ou feaure and he TLE8251VSJ disables he ransmier (see Figure 9). The receiver is sill acive and he he RxD oupu coninues monioring daa on he bus. CANH CANL > TxD TxD ime-ou TxD ime ou released TxD RxD Figure 9 TxD ime-ou funcion Figure 9 illusraes how he ransmier is deacivaed and acivaed again. A permanen low signal on he TxD inpu pin acivaes he TxD ime-ou funcion and deacivaes he ransmier. To release he ransmier afer a TxD ime-ou even he TLE8251VSJ requires a signal change on he TxD inpu pin from logical low o logical high. Daa Shee 14 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Fail Safe Funcions 5.4 Overemperaure Proecion The inegraed overemperaure deecion proecs he TLE8251VSJ agains hermal oversress of he ransmier. Overemperaure proecion is acive in normal-operaing mode and disabled in sand-by mode. In overemperaure condiion, he emperaure sensor disables he ransmier (see Figure 1) while he ransceiver remains in normal-operaing mode. Afer he device has cooled down he ransmier is acivaed again (see Figure 10). A hyseresis is implemened wihin he emperaure sensor. TJ TJSD (shu down emperaure) T cool down swich-on ransmier CANH CANL TxD RxD Figure 10 Overemperaure proecion 5.5 Delay Time for Mode Change The HS CAN ransceiver TLE8251VSJ changes he mode of operaion wihin he ime window Mode. During he mode change he RxD oupu pin is permanenly se o logical high and does no reflec he saus on he CANH and CANL inpu pins. While changing he mode of operaion from normal-operaing mode o sand-by mode, he ransceiver TLE8251VSJ urns off he ransmier and swiches from he normal-mode receiver o he low-power receiver. Afer he mode change is compleed, he ransceiver TLE8251VSJ releases he RxD oupu pin (see as an example Figure 16 and Figure 17). Daa Shee 15 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up General Produc Characerisics 6 General Produc Characerisics 6.1 Absolue Maximum Raings Table 3 Absolue maximum raings volages, currens and emperaures 1) All volages wih respec o ground; posiive curren flowing ino pin; (unless oherwise specified) Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Volages Transmier supply volage V CC -0.3 6.0 V P_6.1.1 Digial supply volage V IO -0.3 6.0 V P_6.1.2 CANH DC volage versus GND V CANH -40 40 V P_6.1.3 CANL DC volage versus GND V CANL -40 40 V P_6.1.4 Differenial volage beween CANH and CANL Volages a he inpu pins: STB, TxD Volages a he oupu pin: RxD V CAN_Diff -40 40 V P_6.1.5 V MAX_IN -0.3 6.0 V P_6.1.6 V MAX_OUT -0.3 V IO V P_6.1.7 Currens RxD oupu curren I RxD -20 20 ma P_6.1.8 Temperaures Juncion emperaure T j -40 150 C P_6.1.9 Sorage emperaure T S -55 150 C P_6.1.10 ESD Resisiviy ESD immuniy a CANH, CANL versus GND V ESD_HBM_CAN -10 10 kv HBM (100 pf via 1.5 kω) 2) P_6.1.11 P_6.1.12 ESD immuniy a all oher V ESD_HBM_ALL -2 2 kv HBM pins (100 pf via 1.5 kω) 2) ESD immuniy o GND V ESD_CDM -750 750 V CDM 3) P_6.1.13 1) No subjec o producion es, specified by design 2) ESD suscepibiliy, Human Body Model HBM according o ANSI/ESDA/JEDEC JS-001 3) ESD suscepibiliy, Charge Device Model CDM according o EIA/JESD22-C101 or ESDA STM5.3.1 Noe: Sresses above he ones lised here may cause permanen damage o he device. Exposure o absolue maximum raing condiions for exended periods may affec device reliabiliy. Inegraed proecion funcions are designed o preven IC desrucion under faul condiions described in he daa shee. Faul condiions are considered as ouside normal-operaing range. Proecion funcions are no designed for coninuos repeiive operaion. Daa Shee 16 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up General Produc Characerisics 6.2 Funcional Range Table 4 Funcional range Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Supply Volages Transmier supply volage V CC 4.5 5.5 V P_6.2.1 Digial supply volage V IO 3.0 5.5 V P_6.2.2 Thermal Parameers Juncion emperaure T j -40 150 C 1) 1) No subjec o producion es, specified by design. P_6.2.3 Noe: Wihin he funcional range he IC operaes as described in he circui descripion. The elecrical characerisics are specified wihin he condiions given in he relaed elecrical characerisics able. 6.3 Thermal Resisance Noe: This hermal daa was generaed in accordance wih JEDEC JESD51 sandards. For more informaion, please visi www.jedec.org. Table 5 Thermal resisance 1) Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Thermal Resisances Juncion o Ambien PG- DSO-8 R hja 130 K/W 2) TLE8251VSJ P_6.3.1 Thermal Shudown (juncion emperaure) Thermal shudown emperaure T JSD 150 175 200 C P_6.3.2 Thermal shudown hyseresis ΔT 10 K P_6.3.3 1) No subjec o producion es, specified by design 2) Specified R hja value is according o Jedec JESD51-2,-7 a naural convecion on FR4 2s2p board. The produc (TLE8251VSJ) was simulaed on a 76.2 x 114.3 x 1.5 mm board wih 2 inner copper layers (2 x 70µm Cu, 2 x 35µm Cu). Daa Shee 17 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics 7 Elecrical Characerisics 7.1 Funcional Device Characerisics Table 6 Elecrical characerisics 4.5 V < V CC <5.5V; 3.0V<V IO <5.5V; R L =60Ω; -40 C < T j < 150 C; all volages wih respec o ground; posiive curren flowing ino pin; unless oherwise specified. Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Curren Consumpion Curren consumpion a V CC normal-operaing mode Curren consumpion a V CC normal-operaing mode Curren consumpion a V IO normal-operaing mode Curren consumpion a V CC sand-by mode Curren consumpion a V IO sand-by mode Curren consumpion a V IO sand-by mode @ 105 C Supply Reses V CC undervolage monior rising edge V CC undervolage monior falling edge V CC undervolage monior hyseresis V IO undervolage monior rising edge V IO undervolage monior falling edge V IO undervolage monior hyseresis V CC and V IO undervolage delay ime, rising edge I CC 2.6 4 ma recessive sae, V TxD = V IO, V STB =0V; I CC 38 60 ma dominan sae, V TxD = V STB =0V; P_7.1.1 P_7.1.2 I IO 1 ma V STB =0V; P_7.1.3 I CC(STB) 5 µa V TxD = V STB =V IO ; P_7.1.4 I IO(STB) 8 14 µa V TxD = V STB = V IO, 0V<V CC <5.5V; I IO(STB)_105 6 12.5 µa V TxD = V STB = V IO, 0V<V CC <5.5V, T < 105 C; P_7.1.5 P_7.1.6 V CC(UV,R) 3.8 4.0 4.3 V P_7.1.7 V CC(UV,F) 3.65 3.85 4.3 V P_7.1.8 V CC(UV,H) 150 mv 1) P_7.1.9 V IO(UV,R) 2.0 2.5 3.0 V P_7.1.10 V IO(UV,F) 1.8 2.3 3.0 V P_7.1.11 V IO(UV,H) 200 mv Delay(UV) 100 µs 1) 1) (see Figure 6 and Figure 7); P_7.1.12 P_7.1.13 Daa Shee 18 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics Table 6 Elecrical characerisics (con d) 4.5 V < V CC <5.5V; 3.0V<V IO <5.5V; R L =60Ω; -40 C < T j < 150 C; all volages wih respec o ground; posiive curren flowing ino pin; unless oherwise specified. Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Receiver Oupu RxD High level oupu curren I RD,H -4-2 ma V RxD = V IO -0.4V, P_7.1.14 V Diff <0.5V; Low level oupu curren I RD,L 2 4 ma V RxD =0.4V, V Diff >0.9V; P_7.1.15 Transmission Inpu TxD High level inpu volage hreshold Low level inpu volage hreshold V TxD,H 0.5 V IO 0.7 V IO V recessive sae; P_7.1.16 V TxD,L 0.3 V IO 0.4 V IO V dominan sae; P_7.1.17 Pull-up resisance R TxD 10 25 50 kω P_7.1.18 Inpu hyseresis V HYS(TxD) 450 mv 1) P_7.1.19 Inpu capaciance C TxD 10 pf 1) P_7.1.20 TxD permanen dominan TxD 4.5 16 ms normal-operaing mode; P_7.1.21 ime-ou Sand-by Inpu STB High level inpu volage hreshold Low level inpu volage hreshold V STB,H 0.5 V IO 0.7 V IO V sand-by mode; P_7.1.22 V STB,L 0.3 V IO 0.4 V IO V normal-operaing mode; P_7.1.23 Pull-up resisance R STB 10 25 50 kω P_7.1.24 Inpu capaciance C STB 10 pf 1) P_7.1.25 Inpu hyseresis V HYS(STB) 200 mv 1) P_7.1.26 Bus Receiver Differenial receiver hreshold dominan normal-operaing mode V Diff_D 0.75 0.9 V 2) P_7.1.27 Differenial receiver hreshold recessive normal-operaing mode Differenial range dominan normal-operaing mode Differenial range recessive normal-operaing mode Differenial receiver hreshold dominan sand-by mode V Diff_R 0.5 0.66 V 2) P_7.1.28 V Diff_D_Range 0.9-8.0 V 1) 2) P_7.1.29 V Diff_R_Range -3.0-0.5 V 1) 2) P_7.1.30 V Diff_D_STB 0.75 1.15 V 2) P_7.1.31 Daa Shee 19 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics Table 6 Elecrical characerisics (con d) 4.5 V < V CC <5.5V; 3.0V<V IO <5.5V; R L =60Ω; -40 C < T j < 150 C; all volages wih respec o ground; posiive curren flowing ino pin; unless oherwise specified. Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Differenial receiver hreshold recessive sand-by mode V Diff_R_STB 0.4 0.72 V 2) P_7.1.32 Differenial range dominan V Diff_D_Range 1.15-8.0 V 1)2) P_7.1.33 Sand-by mode _STB Differenial range recessive V Diff_R_Range -3.0-0.4 V 1)2) P_7.1.34 Sand-by mode _STB Common mode range CMR -12 12 V V CC =5V; P_7.1.35 Differenial receiver hyseresis normal-operaing mode V Diff,hys 90 mv 1) P_7.1.36 CANH, CANL inpu resisance R i 10 20 30 kω recessive sae; P_7.1.37 Differenial inpu resisance R Diff 20 40 60 kω recessive sae; P_7.1.38 Inpu resisance deviaion ΔR i - 1 1 % 1) recessive sae; P_7.1.39 beween CANH and CANL Inpu capaciance CANH, C In 20 40 pf 1) V TxD = V IO ; P_7.1.40 CANL versus GND Differenial inpu C In_Diff 10 20 pf 1) V TxD = V IO : P_7.1.41 capaciance Bus Transmier CANL/CANH recessive oupu volage normal-operaing mode CANH, CANL recessive oupu volage difference normal-operaing mode CANH, CANL recessive oupu volage sand-by mode CANH, CANL recessive oupu volage difference sand-by mode CANL dominan oupu volage normal-operaing mode CANH dominan oupu volage normal-operaing mode V CANL/H_R 2.0 2.5 3.0 V V TxD = V IO, no load; V Diff_NM -500 50 mv V TxD = V IO, no load; P_7.1.42 P_7.1.43 V CANL,H_STB -0.1 0.1 V no load; P_7.1.44 V Diff_STB -0.2 0.2 V no load; P_7.1.45 V CANL 0.5 2.25 V V TxD =0V; P_7.1.46 V CANH 2.75 4.5 V V TxD =0V; P_7.1.47 Daa Shee 20 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics Table 6 Elecrical characerisics (con d) 4.5 V < V CC <5.5V; 3.0V<V IO <5.5V; R L =60Ω; -40 C < T j < 150 C; all volages wih respec o ground; posiive curren flowing ino pin; unless oherwise specified. Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. CANH, CANL dominan oupu volage difference normal-operaing mode according o ISO 11898-2 V Diff = V CANH - V CANL CANH, CANL dominan oupu volage difference normal-operaing mode V Diff = V CANH - V CANL CANH, CANL dominan oupu volage difference normal-operaing mode V Diff = V CANH - V CANL V Diff 1.5 3.0 V V TxD =0V, 50 Ω < R L <65Ω, 4.75 < V CC <5.25V; V Diff_EXT 1.4 3.3 V V TxD =0V, 45 Ω < R L <70Ω, 4.75 < V CC <5.25V; V Diff_HEXT 1.5 5 V V TxD =0V, saic behavior, R L = 2240Ω, 4.75 < V CC <5.25V 1) ; P_7.1.48 P_7.1.49 P_7.1.50 Driver dominan symmery normal-operaing mode V SYM =V CANH + V CANL V SYM 4.5 5 5.5 V V CC =5.0V, V TxD =0V; P_7.1.51 CANL shor circui curren I CANLsc 40 75 100 ma V CANLshor =18V, V CC =5.0V, < TxD, V TxD =0V; CANH shor circui curren I CANHsc -100-75 -40 ma V CANHshor = -3 V, V CC =5.0V, < TxD, V TxD =0V; Leakage curren, CANH I CANH,lk -5 5 µa V CC = V IO =0V, 0V<V CANH <5V, V CANH = V CANL; Leakage curren, CANL I CANL,lk -5 5 µa V CC = V IO =0V, 0V<V CANL <5V, V CANH = V CANL; P_7.1.52 P_7.1.53 P_7.1.54 P_7.1.55 Daa Shee 21 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics Table 6 Elecrical characerisics (con d) 4.5 V < V CC <5.5V; 3.0V<V IO <5.5V; R L =60Ω; -40 C < T j < 150 C; all volages wih respec o ground; posiive curren flowing ino pin; unless oherwise specified. Parameer Symbol Values Uni Noe or Tes Condiion Number Min. Typ. Max. Dynamic CAN-Transceiver Characerisics Propagaion delay TxD-o-RxD low ( recessive o dominan) Propagaion delay TxD-o-RxD high (dominan o recessive) Propagaion delay TxD low o bus dominan Propagaion delay TxD high o bus recessive Propagaion delay bus dominan o RxD low Propagaion delay bus recessive o RxD high d(l),tr 170 230 ns C L = 100 pf, 4.75 V < V CC <5.25V, C =15pF; d(h),tr 170 230 ns C L = 100 pf, 4.75 V < V CC <5.25V, C RxD =15pF; d(l),t 90 140 ns C L = 100 pf, 4.75 V < V CC <5.25V, C RxD =15pF; d(h),t 90 140 ns C L = 100 pf, 4.75 V < V CC <5.25V, C RxD =15pF; d(l),r 90 140 ns C L = 100 pf, 4.75 V < V CC <5.25V, C RxD =15pF; d(h),r 90 140 ns C L = 100 pf, 4.75 V < V CC <5.25V, C RxD =15pF; P_7.1.56 P_7.1.57 P_7.1.58 P_7.1.59 P_7.1.60 P_7.1.61 Delay Times Delay ime for mode change Mode 20 µs 1) (see Figure 16); P_7.1.62 RxD reacion delay, sand-by mode o normaloperaing mode, RxD_Rec 5 µs 1) (see Figure 17); P_7.1.63 CAN aciviy filer ime Filer 0.5 5 µs (see Figure 8); P_7.1.64 Wake-up reacion ime WU_Rec 5 µs 1) (see Figure 8); P_7.1.65 Daa Shee 22 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics 7.2 Diagrams 7 CANH V IO 5 100 nf TxD STB 1 8 C L R L RxD 4 6 CANL C RxD GND 2 V CC 3 100 nf Figure 11 Tes circuis for dynamic characerisics TxD 0.7 x VIO 0.3 x VIO d(l),t d(h),t VDiff 0.9 V 0.5 V d(l),r d(h),r Loop(H,L) Loop(L,H) RxD 0.7 x VIO 0.3 x VIO Figure 12 Timing diagrams for dynamic characerisics Daa Shee 24 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Elecrical Characerisics TxD 0.7 x VIO 0.3 x VIO 0.3 x VIO 5 x Bi Bi Loop(H,L) VDiff VDiff = VCANH - VCANL Bi(Bus) 0.5 V 0.9 V Loop(L,H) Bi(RxD) RxD 0.7 x VIO 0.3 x VIO Figure 13 Recessive bi ime - five dominan bis followed by one recessive bi Daa Shee 25 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8 Applicaion Informaion 8.1 ESD Robusness according o IEC61000-4-2 Tess for ESD robusness according o IEC61000-4-2 Gun es (150 pf, 330 Ω) have been performed. The resuls and es condiions are available in a separae es repor. Table 7 ESD robusness according o IEC61000-4-2 Performed Tes Resul Uni Remarks Elecrosaic discharge volage a pin CANH and CANL versus GND +8 kv 1) Posiive pulse Elecrosaic discharge volage a pin CANH and -8 kv 1) Negaive pulse CANL versus GND 1) ESD suscepibiliy ESD GUN according o GIFT / ICT paper: EMC Evaluaion of CAN Transceivers, version 03/02/IEC TS62228, secion 4.3. (DIN EN61000-4-2) Tesed by exernal es faciliy (IBEE Zwickau, EMC es repor no. TBD). Daa Shee 26 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8.2 Applicaion Example V BAT CANH CANL I EN TLE4476D GND Q1 Q2 100 nf 22 uf 100 nf 120 Ohm 22 uf 6 opional: common mode choke 7 3 V CC V IO TLE8251VSJ STB CANH TxD RxD CANL 5 8 1 4 Ou Ou In VCC 100 nf Microconroller e.g. XC22xx GND GND 2 I EN TLE4476D GND Q1 Q2 100 nf 22 uf 120 Ohm 22 uf opional: common mode choke 7 6 3 V CC TLE8251VSJ STB CANH TxD CANL GND 2 V IO RxD 5 8 1 4 100 nf Ou Ou In VCC 100 nf Microconroller e.g. XC22xx GND CANH CANL example ECU design Figure 14 Applicaion circui 8.3 Examples for Mode Changes Changing he saus on he STB inpu pin riggers a change of he operaing mode, disregarding he acual signal on he CANH, CANL and TxD pins (see also Chaper 4.2). Daa Shee 27 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion Mode changes are riggered by he STB pin when he device TLE8251VSJ is fully supplied. Seing he STB pin o logical low changes he mode of operaion o normal-operaing mode: The mode change is execued independenly of he signal on he HS CAN bus. The CANH, CANL inpus may be eiher dominan or recessive. They can be also permanenly shored o GND or V CC. A mode change is performed independenly of he signal on he TxD inpu. The TxD inpu may be eiher logical high or low. Analog o ha, changing he STB inpu pin o logical high changes he mode of operaion o he sand-by mode, independen on he signals a he CANH, CANL and TxD pins. Noe: Noe: In case he TxD signal is low seing he STB inpu pin o logical low changes he operaing mode of he device o normal-operaing mode and drives a dominan signal o he HS CAN bus. The TxD ime-ou is only effecive in normal-operaing mode. The TxD ime-ou imer sars when he TLE8251VSJ eners normal-operaing mode and he TxD inpu is se o logical low. Daa Shee 28 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8.3.1 Mode Change o Sand-by Mode during a dominan Bus Signal Figure 15 shows an example of mode change from normal-operaing mode o sand-by mode while he signal on he HS CAN bus is dominan. During he mode ransiion ime Mode, he TLE8251VSJ blocks he RxD oupu and provides a logical high on he RxD oupu pin. The inernal receiver swiches from he normal-mode receiver o he low-power receiver, while changing from normal-operaing mode o sand-by mode. Afer enering sand-by mode he TLE8251VSJ coninues o indicae a high signal on he RxD oupu as long as he HS CAN bus remains dominan. The permanen dominan bus signal is no considered a wake-up even and is herefore no indicaed on he RxD oupu pin. Deecing he firs signal change from recessive o dominan on he HS CAN bus releases he inernal wake-up logic. Wihin he wake-up reacion ime WU_Rec, a recessive CAN bus signal is indicaed on he RxD oupu pin by a logical high signal and a dominan CAN bus signal is indicaed by a logical low signal, as long as he pulse widh of he HS CAN bus signals exceeds CAN aciviy filer ime > Filer. Enering sand-by mode while he HS CAN bus signal is recessive, a release of he inernal wake-up logic is no necessary and a dominan wake-up signal ( > Filer ) on he HS CAN bus is indicaed on he RxD oupu pin wihin he wake-up reacion ime WU_Rec (compare o Figure 8). Noe: The dominan signal on he HS CAN bus is se by anoher HS CAN bus subscriber. STB = Mode normal-operaing ransiion sand-by mode TxD Filer + WU_Rec Filer + WU_Rec Filer + WU_Rec Filer + WU_Rec VDiff VDiff = VCANH - VCANL 0.4V 1.15V 1.15V 0.4V RxD firs change recessive o dominan RxD low indicaing a dominan bus signal RxD high due o he mode ransiion RxD high The low-power receiver is no deecing a wake-up as long he bus signal is permanenly dominan. The firs change from o recessive o dominan releases he wake-up logic. RxD low indicaing a dominan bus wake-up signal RxD high indicaing a recessive bus wake-up signal Figure 15 Change o sand-by mode during bus dominan Daa Shee 29 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8.3.2 Mode Change from Sand-by Mode o Normal-operaing Mode 8.3.2.1 Mode Change while he TxD Signal is low Figure 16 shows an example of mode change o normal-operaing mode while he TxD inpu is logical low. The HS CAN signal is recessive, assuming all oher HS CAN bus subscribers are also sending a recessive bus signal. While he TLE8251VSJ is in sand-by mode, he ransmier and he normal-mode receiver are urned off. In sand-by mode he low-power receiver is acive. The TLE8251VSJ drives no signal o he HS CAN bus, he RxD oupu is conneced o he low-power receiver and follows only he HS_CAN bus signals when is pulse widh exceeds CAN aciviy filer ime Filer. Changing he STB o logical low urns he mode of operaion o normaloperaing mode, while he TxD inpu signal remains logical low. The ransmier and he normal-mode receiver remain disabled unil he mode ransiion is compleed. During he mode ransiion he RxD oupu is blocked and se o logical high. In normal-operaing mode he ransmier and he normal-mode receiver are acive. The low signal on he TxD inpu drives a dominan signal o he HS CAN bus and he RxD oupu becomes logical low following he dominan signal on he HS CAN bus. Changing he STB pin back o logical high, disables he ransmier and normal-mode receiver again. The RxD oupu pin is blocked and se o logical high wih he sar of he mode ransiion. The TxD inpu and he ransmier are blocked and he HS CAN bus becomes recessive. Noe: The signals on he HS CAN bus are recessive, he dominan signal is generaed by he TxD inpu signal STB = Mode = Mode TxD V Diff RxD sand-by mode ransiion normal-operaing ransiion sand-by mode low-power receiver acive RxD oupu blocked normal-mode receiver acive RxD oupu blocked low-power receiver acive Figure 16 TxD inpu and ransmier blocked TxD inpu and ransmier acive Mode change from sand-by mode o normal-operaing mode TxD inpu and ransmier blocked Daa Shee 30 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8.3.2.2 Mode Change while he Bus Signal is dominan Figure 17 shows an example of mode change while he bus is dominan and he TxD inpu signal is se o logical high. While he TLE8251VSJ is in sand-by mode, he ransmier and he normal-mode receiver are urned off. In sand-by mode he low-power receiver is acive. The TLE8251VSJ drives no signal o he HS CAN bus, he RxD oupu is conneced o he low-power receiver and follows only he HS_CAN bus signals when is pulse widh exceeds he bus wake-up ime WU. Changing he STB o logical low urns he mode of operaion o normaloperaing mode, while he TxD inpu signal remains logical high. The ransmier and he normal-mode receiver remain disabled unil he mode ransiion is compleed. During he mode ransiion he RxD oupu is blocked and se o logical high. In normal-operaing mode he normal-mode receiver is acive and he RxD oupu follows he dominan signal on he HS CAN bus by indicaing a logical low signal. Changing he STB pin back o logical high, disables he ransmier and normal-mode receiver again. The RxD oupu pin is blocked and se o logical high wih he sar of he mode ransiion. The low-power receiver is acive in sand-by mode. The RxD oupu signal remains high as long as he HS CAN bus remains dominan. Only if he HS CAN bus changes o a recessive signal exceeding CAN aciviy filer ime Filer, he RxD oupu follows he bus signal wihin wake-up reacion ime WU_Rec (see also Chaper 8.3.1). Noe: The dominan signal on he HS CAN bus is se by anoher HS CAN bus subscriber. = Mode = Mode STB TxD V Diff Filer + WU_Rec RxD_Rec RxD sand-by mode ransiion normal-operaing ransiion sand-by mode low-power receiver acive RxD oupu blocked normal-mode receiver acive RxD oupu blocked low-power receiver acive TxD inpu and ransmier blocked TxD inpu & ransmier acive TxD inpu and ransmier blocked Figure 17 Receiving a dominan signal from he bus during a mode change Daa Shee 31 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Applicaion Informaion 8.4 Furher Applicaion Informaion Please conac us for informaion regarding he pin FMEA. Exising applicaion noe. For furher informaion you may visi: hp://www.infineon.com/ransceiver Daa Shee 32 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Package Ouline 9 Package Ouline 0.41 1.27 +0.1 2) -0.06 0.175±0.07 (1.45) 1.75 MAX. 0.1 0.2 M A B 8x B 0.35 x 45 1) 4-0.2 C 6 ±0.2 +0.06 0.19 0.64 ±0.25 8 MAX. 0.2 M C 8x 8 5 1 4 1) 5-0.2 A Index Marking Figure 18 1) Does no include plasic or meal prorusion of 0.15 max. per side 2) Lead widh can be 0.61 max. in dambar area GPS01181 PG-DSO-8 (Plasic Dual Small Ouline PG-DSO-8) Green Produc (RoHS complian) To mee he world-wide cusomer requiremens for environmenally friendly producs and o be complian wih governmen regulaions he device is available as a green produc. Green producs are RoHS complian (i.e Pb-free finish on leads and suiable for Pb-free soldering according o IPC/JEDEC J-STD-020). For furher informaion on alernaive packages, please visi our websie: hp://www.infineon.com/packages. Dimensions in mm Daa Shee 33 Rev. 1.0

High Speed CAN Transceiver wih Bus Wake-up Revision Hisory 10 Revision Hisory Revision Dae Changes 1.0 Daa Shee creaed. Daa Shee 34 Rev. 1.0

Please read he Imporan Noice and Warnings a he end of his documen Trademarks of Infineon Technologies AG µhvic, µipm, µpfc, AU-ConverIR, AURIX, C166, CanPAK, CIPOS, CIPURSE, CoolDP, CoolGaN, COOLiR, CoolMOS, CoolSET, CoolSiC, DAVE, DI-POL, DirecFET, DrBlade, EasyPIM, EconoBRIDGE, EconoDUAL, EconoPACK, EconoPIM, EiceDRIVER, eupec, FCOS, GaNpowIR, HEXFET, HITFET, HybridPACK, imotion, IRAM, ISOFACE, IsoPACK, LEDrivIR, LITIX, MIPAQ, ModSTACK, my-d, NovalihIC, OPTIGA, OpiMOS, ORIGA, PowIRaudio, PowIRSage, PrimePACK, PrimeSTACK, PROFET, PRO-SIL, RASIC, REAL3, SmarLEWIS, SOLID FLASH, SPOC, SrongIRFET, SupIRBuck, TEMPFET, TRENCHSTOP, TriCore, UHVIC, XHP, XMC. Trademarks updaed November 2015 Oher Trademarks All referenced produc or service names and rademarks are he propery of heir respecive owners. Ediion Published by Infineon Technologies AG 81726 Munich, Germany 2016 Infineon Technologies AG. All Righs Reserved. Do you have a quesion abou any aspec of his documen? Email: erraum@infineon.com IMPORTANT NOTICE The informaion given in his documen shall in no even be regarded as a guaranee of condiions or characerisics ("Beschaffenheisgaranie"). Wih respec o any examples, hins or any ypical values saed herein and/or any informaion regarding he applicaion of he produc, Infineon Technologies hereby disclaims any and all warranies and liabiliies of any kind, including wihou limiaion warranies of non-infringemen of inellecual propery righs of any hird pary. In addiion, any informaion given in his documen is subjec o cusomer's compliance wih is obligaions saed in his documen and any applicable legal requiremens, norms and sandards concerning cusomer's producs and any use of he produc of Infineon Technologies in cusomer's applicaions. The daa conained in his documen is exclusively inended for echnically rained saff. I is he responsibiliy of cusomer's echnical deparmens o evaluae he suiabiliy of he produc for he inended applicaion and he compleeness of he produc informaion given in his documen wih respec o such applicaion. For furher informaion on echnology, delivery erms and condiions and prices, please conac he neares Infineon Technologies Office (www.infineon.com). WARNINGS Due o echnical requiremens producs may conain dangerous subsances. For informaion on he ypes in quesion please conac your neares Infineon Technologies office. Excep as oherwise explicily approved by Infineon Technologies in a wrien documen signed by auhorized represenaives of Infineon Technologies, Infineon Technologies producs may no be used in any applicaions where a failure of he produc or any consequences of he use hereof can reasonably be expeced o resul in personal injury.