TracVision. with Multi-service Interface Box/Controller. TracVision M1DX User s Guide

Similar documents
TracVision M3 DX Version. Circular Configuration. TracVision M3 User s Guide

TracVision Interface Box Circular Configuration for North America. TracVision Interface Box User s Guide

TracVision R6 & Multi-service Interface Box. User s Guide

TracVision R1DX. with Multi-service Interface Box/Controller. TracVision R1DX Installation Guide

Welcome! Troubleshooting. Can the antenna see the satellite? Turning On the System. Single-Receiver Setup. Product Serial Number

TracVision R6DX Installation Guide

TracVision M1 Installation Guide. TracVision

KVH Tri-Sat AutoSwitch Kit Installation and Operation Instructions for TracVision M3DX

TracVision M5/M7 Control Panel Configuration. TracVision M5/M7 User s Guide

TracVision R6DX Installation Guide

TracVision M5/M7 User s Guide

TracVision Master Receiver Selector Quick Start Guide

TracVision M9 Standard Configuration. TracVision M9 User s Guide

TracVision M5/M7. Configuration. GyroTrac. User s Guide

TracVision M5/M7 Switchplate Configuration. TracVision M5/M7 User s Guide

Portable In-Motion Automatic Satellite System. Model VQ3000

Portable Automatic Satellite System. Model VQ2000

Subject: DISH Network s Reconfiguration of the 129 W Satellite

Satellite Television. A Guide to TracVision G4. user s guide. Operating Instructions. KVH TracVision G4

IMPORTANT! Special Instructions for the TracVision M3DX Conversion System ( )

Satellite Television. A Guide to TracVision 6. user s guide. Operating Instructions. KVH TracVision 6

TracVision M1/M3. Satellite TV to go!

SATFI UK User Manual Ver. 1.0 SATFI UK DP300. User Manual

In-Motion Automatic Satellite System. Model V30

In-Motion Automatic Satellite System. Model V30

Troubleshooting Guide

TracVision TV1 & TV3. Ultra-compact systems for bringing the best satellite TV entertainment onboard

Automatic Satellite System. Model V20

KOP4800 Owner s Manual

WINEGARD. Operation Manual Made in the U.S.A. For up-to-date information on receiver compatibility and programming, visit

Automatic Satellite System. Model KD5500

Free Way 1M. In Motion Satellite Antenna. User Manual. Ver. 1.0

WINEGARD. RoadTrip Digital Satellite Mobile TV Antenna for Two Receivers. OPERATION MANUAL Made in the U.S.A. U.S. Patent Nos.

Specifications. Compatible Receivers. Compatible Satellites. DIRECTV Sat DISH Sat DIRECTV Receiver Compatibility

OSD. EXECUTIVE / MiniDome USERS MANUAL. USING THE MOTOSAT DISH POINTING SYSTEM EXECUTIVE / MiniDome OSD

INSTALLATION & OPERATION PROCEDURE FOR SEA TEL HDTV 110 WEST CONVERTER KIT

Personal Information Page

KD5500. Automatic Satellite TV Antenna for DISH Programming. Owner s Manual

Satellite Television. A Guide to TracVision LF/SF. owner s manual. Installation Instructions User s Guide Technical Manual. KVH TracVision LF/SF

UC1000 Universal Controller

15 Marine Satellite System. Model 1200-KU

Field Service Procedure Replacement PCU Kit, Coastal

500+ channels. With the all-new KVH TracVision M-series, enjoy satellite TV wherever you operate!

Satellite Terminal Troubleshooting Guide. Release 2.2

Satellite Television. A Guide to TracVision LF/SF. owner s manual. Installation Instructions User s Guide Technical Manual. KVH TracVision LF/SF

TracVision RV1 User s Guide

TracVision 95W LNB Installation

TracVision M-series. Enjoy Satellite TV...wherever you go!

TracVision TV-series. Sophisticated technology that s simple to use for the best TV entertainment onboard

Intellian MIM Serial Number

TracVision M-series Enjoy Satellite TV...wherever you go!

Field Service Procedure Replacement PCU Kit, ST24

In-Motion Satellite System. Model 9754 Model 9754-LP

RV SATELLITE ANTENNA AUTOMATIC SKEW TWIN LNB SSA-850

VHF + UHF Amplified HDTV Antenna Model OA8000 & OA8001 Installation Instructions Reception Frequencies

KOP4800 Owner s Manual

Troubleshooting Guide 9630 Series

Specifications. Dual Satellite Tracking Meter. With a built in 22Khz tone generator. Overview

TracVision HD7. Installation Guide

ATLANTA ASF 2033HD+ DVB-S/S2 METER. User`s Manual

TV for Trucks. Great for team driving or recording shows while traveling. Automatic In-Motion Roof-Mounted Satellite TV Antenna

HD Digital Set-Top Box Quick Start Guide

Instruction Manual. Do not return antenna to place of purchase. Power Inserter. See page 2 for setup instructions

Owner s Manual. Sat-Meter MSK 15. Order No.:

PORTABLE SATELLITE TV SYSTEM VQ1000 OPERATION MANUAL

CAUTION RISK OF ELECTRIC SHOCK NO NOT OPEN

OCEAN TV. Satellite Antennas. Ocean Series O60M Installation and User Manual Version 1.1. Ocean TV Ocean Series Antennas

User s Guide. Model VQ4400

VQ4500 & VQ4510 Owner s Manual

User Guide. Do not return antenna to place of purchase

TracVision HD-series. Delivering the finest TV entertainment, in high definition, wherever you cruise

When this guideline is to be used?

Be sure to run the vehicle engine while using this unit to avoid battery exhaustion.

VQ4900 Owner s Manual. To start using your DISH Tailgater Pro right away, see the Quick Reference Guide.

TracVision Mobile Receiver. for DIRECTV Service. User s Guide

Automatic Satellite System. KD-2200 Stationary KD-3200 In-Motion

Evolution Digital HD Set-Top Box Important Safety Instructions

Mobile Satellite TV Antenna With FastFind Remote Operating Manual

Rain+Birdt. Landscape Irrigation & Maintenance Remote System. Quick Start Guide 4.00 F G H K 9X. c n. System Components

UHF Pro Remote Control

DIGITAL VIDEO RECORDING (DVR) SERVICES

Instructions Manual

Bonding. Black Ground Wire Indicates # 17ga CCS Bond. Green Bonding Wire Indicates # 10ga Solid Copper. External Wall

Brillantes Fernsehen. Seaman. user manual. English. Seaman 37 Seaman 45 Seaman 60

Dealer Training Test. Winegard Dealer Training

Field Service Procedure Replacement GACP Control Panel Kit, ST24

Installation Guide. TracVision M7. TracVision M7 GyroTrac Configuration

TracVision HD7. Installation Guide

USER MANUEL. SNIPE 2 Ref R13

User s Guide. Models VQ4400 & VQ4410

Table of Contents. 1. Safety Use. 2. General Description. 3. Connection Diagram. 4. Operations and Management. 4.1 Display Status. 4.

Cisco 9865H Signal Decoder Troubleshooting Guide

Sea-King Fully Stabilized Marine Satellite System 9762-SW. Installation and Operating Instructions

WINEGARD. Movin View. Digital Satellite Mobile Antenna for Two Receivers for Use While Stationary or In-Motion Model MV-4002

For receivers and programming, call

DVB-T Box, USB Monheim/Germany Tel. +49 (0)9091/ Fax +49 (0)9091/ Hama GmbH & Co KG.

KOP4800 Owner s Manual

Instruction Manual for DIRECTV Users

DIRECTV Multi-Satellite Receiver SIR-S60W. Owner s Manual

EAGLE RE-1 CONTROLLER For Use On MotoSAT HD Mounts

Transcription:

TracVision M1DX with Multi-service Interface Box/Controller TracVision M1DX User s Guide

TracVision M1DX Multi-service Interface Box/ Controller Configuration User s Guide This user s guide provides all of the basic information you need to operate, set up, and troubleshoot the TracVision M1DX satellite TV antenna system. For detailed installation information, please refer to the TracVision M1DX Installation Guide. Please direct questions, comments, or suggestions to: KVH Industries, Inc. 50 Enterprise Center Middletown, RI 02842-5279 USA Tel: +1 401 847-3327 Fax: +1 401 849-0045 E-mail: info@kvh.com Internet: www.kvh.com If you have any comments regarding this manual, please e-mail them to manuals@kvh.com. Your input is greatly appreciated! KVH Part # 54-0580 Rev. C 2008-2011, KVH Industries, Inc., All rights reserved. U.S. Patents Pending

Trademark Information TracVision, KVH, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH Industries, Inc. DVB (Digital Video Broadcasting) is a registered trademark of the DVB Project. DIRECTV is an official trademark of DIRECTV, Inc. DISH Network is an official trademark of EchoStar Communications Corporation. All other trademarks are the property of their respective owners. Disclaimer Every effort has been made to ensure the correctness and completeness of the material in this document. No company shall be liable for errors contained herein. The information in this document is subject to change without notice. No warranty of any kind is made with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Table of Contents Table of Contents 1 Introduction Using this Manual...3 System Overview...5 2 Operation Receiving Satellite TV Signals...11 Turning the System On/Off...12 Understanding the Status Screen...13 Switching Satellites...14 Changing the Satellite Switching Mode...16 Product Care...17 3 System Preferences Adjusting the Display Brightness...21 Entering Latitude/Longitude...22 4 Setup DISH Network Setup...25 DIRECTV Setup...30 Manual Mode Setup...32 Resetting the System to Change Setup...33 i

Table of Contents 5 Troubleshooting Five Simple Checks...37 System Status Lights...38 Error Messages...40 Running the Diagnostics Test...41 Viewing System Information...43 Calibrating the Gyros...45 Changing Tracking Parameters...46 Technical Support...48 A Wiring Diagrams Wiring Diagram - 1 Receiver...51 Wiring Diagram - 2 Receivers...52 Wiring Diagram - 3 Receivers...53 B Menus Quick Reference Guide Interface Box Menus...57 ii

Chapter 1 - Introduction 1. Introduction Contents This chapter provides a basic overview of this manual and your TracVision system. Using this Manual... 3 System Overview... 5 1

Chapter 1 - Introduction Using this Manual This manual provides complete operation, setup, and troubleshooting information for your TracVision system. Who Should Use This Manual Flowchart Conventions The user should refer to the Operation and System Preferences chapters to learn how to operate the system. The user, installer, or servicing technician should refer to the Setup chapter for information on configuring the system for the desired satellite TV service and satellites. The user, installer, or servicing technician should also refer to the Wiring Diagrams appendix for information on connecting additional receivers. The user and/or servicing technician/installer should refer to the Troubleshooting chapter to help identify the cause of a system problem. When instructions indicate to select a specific menu option, press the corresponding interface box button located below the display (see Figure 1). Figure 1 Example of Menu Option and Corresponding Interface Box Button ANTENNA= MANUAL? 3

Chapter 1 - Introduction Typographical Conventions This manual uses the following typographical conventions: Text Example SELECT SATELLITES See System Overview on page 5. Description Text as it appears on the interface box display; also denotes receiver remote control buttons Cross-reference to another chapter in the manual or to a website Types of Notices This manual uses the following types of notices to call attention to important or related information: IMPORTANT! Be sure to read these carefully to ensure proper operation and configuration of your TracVision system. NOTE: Notes contain useful information about system settings. TIP: Tips contain helpful information, allowing you to get the most out of your TracVision system. Related Documentation In addition to this User s Guide, the following documents are provided with your TracVision system: Document Installation Guide Product Registration Form Warranty Statement Contents List Description Complete installation instructions Details on registering the product Warranty terms and conditions List of every part supplied in the kit 4

SATELLITE CANCEL OFF-AIR HDTV SATELLITE RECEIVER POWER SYSTEM INFO TracVision M1DX User s Guide Chapter 1 - Introduction System Overview Your TracVision M1DX is a state-of-the-art, actively stabilized antenna system that delivers live satellite TV to your mobile audio/video entertainment system. A basic system is illustrated below. Detailed wiring diagrams are provided in Wiring Diagrams on page 49. Figure 2 TracVision M1DX Basic System Diagram KVH TracVision M1DX Antenna KVH Multi-service Interface Box/Controller Satellite TV Receiver Customer-supplied; see page 6 for list of KVH-validated receivers Television Customer-supplied 5

Chapter 1 - Introduction System Components The TracVision M1DX system includes the following components: The antenna uses integrated DVB technology to quickly acquire and track the correct satellite, switch between satellites, and send TV signals to the interface box. Internal gyros allow the antenna to track the satellite at all times, even while you re on the move! Compatible Receivers The multi-service interface box/controller supplies power to the antenna and delivers satellite TV signals to your satellite TV receiver. The interface box also allows you to set up the system using the pushbuttons and LCD display. NOTE: Henceforward, this manual uses the term interface box to refer to the multi-service interface box/controller. To ensure compatibility with the TracVision system, KVH recommends the receiver models shown in the table below. These receivers have all been validated by KVH to work well with the TracVision system. For information on connecting different receiver models, contact KVH Technical Support at 401-847-3327. Figure 3 KVH-Validated Receivers Standard-Definition Models DIRECTV D12 D11 D10 DISH Network 311 211k 211 High-Definition (HD) Models DIRECTV HD not supported DISH Network 211k 211 6

Chapter 1 - Introduction DISH Network Configuration DIRECTV Configuration Other than a satellite TV receiver, no additional components are necessary to receive both highdefinition (HD) and standard-definition N E T W O R K programming from three DISH Network satellites: 119, 110, and either 61 or 129 (choose the third satellite for your particular region - see DISH Network Setup on page 25). The antenna will automatically switch between these three satellites as necessary as you change channels using the primary receiver s remote. You can receive DIRECTV programming from the 101 and 119 satellites without any special equipment. All you need is a DIRECTV receiver. The antenna will automatically switch between these two satellites as necessary as you change channels using the primary receiver s remote. 7

Chapter 2 - Operation 2. Operation Contents This chapter explains everything you need to know to operate the TracVision system. Receiving Satellite TV Signals... 11 Turning the System On/Off... 12 Understanding the Status Screen... 13 Switching Satellites... 14 Changing the Satellite Switching Mode... 16 Product Care... 17 9

TracVision TracVision M1DX User s Guide Chapter 2 - Operation Receiving Satellite TV Signals Television satellites are located in fixed positions above the Earth s equator and beam TV signals down to certain regions of the planet (not worldwide). To receive TV signals from a satellite, you must be located within that satellite s unique coverage area. TIP: For your convenience, KVH provides links to several websites that offer satellite coverage information. Simply visit our website at www.kvh.com/ footprint. Figure 4 Example of a Satellite Location and Coverage Area Equator In addition, since TV satellites are located above the equator, the TracVision antenna must have a clear view of the sky to receive satellite TV signals. Anything that stands between the antenna and the satellite can block the signal, resulting in lost reception. Common causes of blockage include trees, buildings, bridges, and onboard equipment. Heavy rain, ice, or snow might also temporarily interrupt satellite signals. Figure 5 Example of Satellite Blockage Blocked! 11

Chapter 2 - Operation Turning the System On/Off Turning On the System Since the interface box supplies power to the antenna, you can turn the antenna on or off using the interface box Power switch. Follow the steps below to turn on your TracVision system. 1. Make sure the antenna has a clear view of the sky. 2. Turn on your satellite TV receiver and TV. 3. Press the Power switch on the front of the TracVision interface box. Figure 6 Interface Box Components Display Power Switch Status Lights Buttons Turning Off the System 4. Wait one minute for system startup. Once the antenna finds the correct satellite, all three status lights on the interface box should be lit green. If any lights are not lit green, see System Status Lights on page 38. Follow the steps below to turn off your TracVision system. 1. Press the Power switch on the front of the TracVision interface box. 2. Turn off your satellite TV receiver and TV. 12

Chapter 2 - Operation Understanding the Status Screen Following startup, the interface box displays the current system status. Figure 7 Interface Box Status Screen Antenna State Service TRACKING DISH 119 DISH 1000/129 MODE Satellite Signal Strength Operating Mode Screen Field Antenna State Service Satellite Signal Strength Operating Mode Description Current state of the antenna: Idle Initializing Searching Tracking Error Satellite TV service currently set up in the TracVision system: DTV (DIRECTV) DISH (DISH Network) MAN (Manual) Satellite that the antenna is currently tracking This number refers to the satellite s orbital slot, which is its longitudinal location above the equator. Strength of the satellite TV signal, as measured by RF level The more bars, the stronger the signal, just like a cell phone. Three bars = good reception. Mode of operation currently set up in the TracVision system: Dual-Sat (DIRECTV) DISH 1000/129 (DISH Network) DISH 1000/61 (DISH Network) DISH 500 (DISH Network) For a list of satellites tracked in each operating mode, see Setup on page 23. 13

Chapter 2 - Operation Switching Satellites If your system is set up to track multiple satellites, you can easily switch between them. Use the switching method that applies to your particular setup. You can identify the current satellite switching method by the format of the status screen: Status Screen Examples TRACKING DISH 119 DISH 1000/129 MODE Satellite Switching Method Automatic TRACKING DISH 119 PUSH TO SWITCH SAT Manual 14

Chapter 2 - Operation Automatic Switching Manual Switching All operating modes provide automatic satellite switching using the primary receiver (the receiver connected to the Unstacked Output jack on the interface box). The antenna will automatically switch satellites as you change channels using the primary receiver s remote. NOTE: The receiver might take up to 30 seconds to display video when changing channels, switching between satellites, and/or switching between standard-definition and high-definition channels. NOTE: DISH Network receivers may switch to a different satellite on their own in response to a blockage condition. For example, if the antenna s view of the 110 satellite becomes blocked for over a minute, the receiver may try switching to the 119 satellite. If this occurs, you will see an error message on the TV. Once the antenna can see the selected satellite again, the receiver will automatically switch back and the error message will disappear. How Switching Satellites Affects Additional Receivers The TracVision system tracks one satellite at a time. Therefore, if you switch satellites using the primary receiver, televisions connected to other receivers might display different programming, no programming, or an error message. Simply select a channel carried by the new satellite, or use the primary receiver to switch back to the original satellite. Only the primary receiver controls satellite selection. If you set up the system to track a custom set of satellites in Manual mode, you can use the interface box to switch among them. Simply press the CHANGE button until the display shows the desired satellite. Then press ACCEPT. 15

Chapter 2 - Operation Changing the Satellite Switching Mode Unless your system is set up in Manual mode, the antenna will automatically switch satellites as you change channels using the receiver s remote control. However, if you want to manually select a satellite for some reason, the interface box allows you to switch from automatic to manual switching. (You can also switch back to automatic switching using this same menu function.) Follow the steps in the flowchart below to change the satellite switching mode. Figure 8 Satellite Switching Mode Press MENUS until DIAGNOSTICS= No is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE Press MENUS until SAT SWITCH= AUTO is displayed. SAT SWITCH= AUTO NEXT MENU CHANGE SAT SWITCH= MANUAL? SAT SWITCH= MANUAL 16

Chapter 2 - Operation Product Care Please consider the following antenna care guidelines for maintaining peak performance: Periodically wash the exterior of the antenna dome with fresh water and mild detergent. Avoid harsh cleansers and volatile solvents (such as acetone) and do not spray the dome directly with high-pressure water. If you wish to paint the dome, use only non-metallic automotive paint without a primer coat. Any paint that contains metal will block satellite signals and impair reception. 17

Chapter 3 - System Preferences 3. System Preferences Contents This chapter explains how to change the brightness and latitude/ longitude settings. Adjusting the Display Brightness... 21 Entering Latitude/Longitude... 22 19

Chapter 3 - System Preferences Adjusting the Display Brightness Follow the steps in the flowchart below if you need to adjust the brightness of the interface box display. Figure 9 Brightness Setting Press MENUS until BRIGHTNESS is displayed. BRIGHTNESS= HIGH NEXT MENU CHANGE BRIGHTNESS= MEDIUM? Press CHANGE until the desired setting is displayed: HIGH, MEDIUM, or LOW. BRIGHTNESS= MEDIUM Press EXIT to exit the menu. 21

Chapter 3 - System Preferences Entering Latitude/Longitude Follow the steps in the flowchart below to enter your vessel s latitude and longitude into the system. The antenna will use your position information to speed up satellite acquisition. (If the antenna knows where you are located, it knows where it should start looking for the satellite.) Figure 10 Latitude/Longitude Setting Press MENUS until LAT/LONG is displayed. LAT/LONG= 41N, 071W NEXT MENU CHANGE LAT/LONG= 41N, 071W? LAT/LONG= 41N, 071W LAT/LONG= 55N, 012E? Press CHANGE to set each digit plus N/S (north or south) and E/W (east or west). Press ACCEPT to save each digit. RESTARTING ANTENNA 22

Chapter 4 - Setup 4. Setup Contents When you turn on the TracVision system for the first time, the interface box display shows SYSTEM NEEDS SETUP. This chapter explains how to set up the system for your desired satellite TV service. DISH Network Setup... 25 DIRECTV Setup... 30 Manual Mode Setup... 32 Resetting the System to Change Setup... 33 23

Chapter 4 - Setup DISH Network Setup You can set up the system for any one of the following DISH Network operating modes: Mode Satellites Tracked N E T W O R K DISH 1000/129 119, 110, and 129 DISH 1000/61 119, 110, and 61 DISH 500 119 and 110 Whichever mode you choose, the antenna will automatically switch between satellites as necessary as you change channels using your primary receiver s remote control. DISH 1000/129 or DISH 1000/61 To ensure you receive the best satellite reception, use the map in Figure 11 to help determine the appropriate DISH 1000 mode for your geographic area. Check with DISH Network for local channels availability. Figure 11 Approximate Areas Recommended for DISH 1000 Modes = DISH 129 Satellite Recommended = DISH 61 Satellite Recommended DISH 500 Select this mode if you wish to receive programming from just the 119 and 110 satellites for DISH 500 service. Setup Process Once you have chosen an operating mode, perform the steps on the following pages to set up the system for DISH Network service: 1. Set the operating mode in the antenna 2. Run receiver Check Switch tests 25

Chapter 4 - Setup Step 1 - Set the Operating Mode in the Antenna Follow the steps in Figure 12 to set up the antenna for your selected DISH Network operating mode. Then keep the antenna turned on for the next step. NOTE: If the status screen does not show SYSTEM NEEDS SETUP, follow the steps in Resetting the System to Change Setup on page 33. Figure 12 DISH Network Setup TRACKING DTV 101 SYSTEM NEEDS SETUP Press any button to begin. SERVICE= DIRECTV? SERVICE= DISH? MODE= DISH 1000/129? Press CHANGE until desired mode displays; then press ACCEPT. MODE= DISH 1000/61? MODE= DISH 500? INSTALLING DISH SATS Displays satellites installed for the selected mode. RESTARTING ANTENNA

Chapter 4 - Setup Step 2 - Run Receiver Check Switch Tests IMPORTANT! If your primary receiver was preconfigured by KVH for your desired DISH Network satellites, you only need to run one Check Switch test to set up the system, not two as described below. To configure the primary receiver for your selected DISH Network mode and automatic satellite switching, you need to run two Check Switch tests on the receiver. The first Check Switch test finds the correct satellites; the second configures the receiver for those satellites. To configure additional receivers for your selected mode, you need to run just one Check Switch test on each (see page 29). IMPORTANT! If you remove a receiver from the vessel and configure it for a home setup, you will need to repeat this step to reconfigure that receiver for a mobile setup whenever you reconnect it to the TracVision system. Primary Receiver - Run Two Check Switch Tests Follow these steps to run two Check Switch tests on the primary receiver, which is connected to the Unstacked Output jack on the interface box. This receiver controls satellite selection. 1. Make sure the vessel is docked in calm water, and ensure the antenna has an unobstructed view of the sky so it can see all of the desired satellites. 2. Apply power to the TV and receiver. (If the antenna is turned off, turn it back on using the interface box power switch and wait for system startup, until the interface box shows TRACKING. ) 3. Using the receiver s remote, go to the Point Dish/ Signal Strength screen (press MENU, 6, 1, 1). 4. Choose Check Switch, then press SELECT. 5. Choose Test, then press SELECT. 6. Wait at least 15 minutes, or until the interface box shows PLEASE RUN ANOTHER CHECK SWITCH, before proceeding to allow the antenna to find all of the satellites. Disregard any messages that appear on the TV screen; they do not correctly indicate when the antenna is ready for the next Check Switch test. 7. Once you have waited the appropriate amount of time, select Test again to run a second Check Switch test. 27

Chapter 4 - Setup 8. Once the Check Switch test is complete, refer to the tables in Figure 13 and verify the values displayed on your TV match those required for your selected service. If your values match: Exit the menu and allow the receiver to download the program guide. If your values do not match: Reset the system (follow the process on page 33), then repeat the entire DISH setup process, starting with Step 1 on page 26. Figure 13 Expected Check Switch Results DISH 1000/129 Results Port 1 2 3 Satellite 119 110 129 Trans OK OK OK Status Switch Reception Verified SW64 DISH 1000/61 Results Port 1 2 3 Satellite 119 110 61.5 Trans OK OK OK Status Switch Reception Verified SW64 DISH 500 Results Input 1 1 2 2 Satellite 119 119 110 110 Polarity Odd Even Odd Even Status Switch Reception Verified SW42 28

Chapter 4 - Setup Additional Receiver(s) - Run One Check Switch Test IMPORTANT! You do not need to run a Check Switch test on an additional receiver if it was preconfigured by KVH for your desired DISH Network satellites. If any receivers are connected to the Stacked Output jack on the interface box, follow these steps to run a single Check Switch test on each additional receiver, one at a time. 1. Temporarily disconnect the primary receiver from the Unstacked Output jack on the interface box. Connect the additional receiver in its place. 2. Perform Steps 1-5 on page 27 to run the test. 3. Wait 15 minutes, then verify that the values displayed on the TV match those shown in Figure 13 on page 28. If the values do not match, try running another Check Switch test. 29

Chapter 4 - Setup DIRECTV Setup You can set up the system for any one of the following DIRECTV operating modes: Mode Tri-Sat Auto Satellites Tracked Not used Tri-Sat Pairs Dual-Sat 101 and 119 Tri-Sat Auto or Tri-Sat Pairs Not Used These modes are no longer used. The Tri-Sat Auto mode supported the Tri-Sat AutoSwitch; the Tri-Sat Pairs mode supported the HDTV Converter. Neither of these devices is available today. Dual-Sat Select this mode to receive programming from the 101 and 119 satellites for DIRECTV service. Follow the steps in Figure 14 on page 31 to set up the antenna. NOTE: If the status screen does not show SYSTEM NEEDS SETUP, follow the steps in Resetting the System to Change Setup on page 33. 30

Chapter 4 - Setup Figure 14 DIRECTV Setup TRACKING DTV 101 SYSTEM NEEDS SETUP Press any button to begin. SERVICE= DIRECTV? MODE= TRI-SAT AUTO? Press CHANGE until DUAL-SAT is displayed. MODE= TRI-SAT PAIRS? MODE= DUAL-SAT? INSTALLING DTV SATS 101 119 RESTARTING ANTENNA 31

Chapter 4 - Setup Manual Mode Setup If none of the automatic modes described earlier include all of the satellites you wish to track, you can set up the system in Manual mode to track up to five satellites of your choice. You will then be able to switch between these satellites using the buttons on the interface box. Follow the steps in Figure 15 to set up the antenna in Manual mode. NOTE: If the status screen does not show SYSTEM NEEDS SETUP, follow the steps in Resetting the System to Change Setup on page 33. Figure 15 Manual Mode Setup TRACKING DTV 101 SYSTEM NEEDS SETUP Press any button to begin. SERVICE= DIRECTV? Press CHANGE until SERVICE= MANUAL is displayed. SERVICE= MANUAL? SAT 1 OF 5= 101? SAT 2 OF 5= NONE? Press CHANGE until the display shows the desired satellite: 61, 72, 82, 91, 101, 110, 119, 129, or NONE. Then press ACCEPT. Repeat this procedure for satellites 3-5. Then press ACCEPT. INSTALLING SATS XXX XXX XXX XXX XXX RESTARTING ANTENNA 32

Chapter 4 - Setup Resetting the System to Change Setup If you need to change the antenna s setup to receive a different satellite TV service and/or track a different satellite, follow the steps in Figure 16 to reset the system. Once the system has reset to its factory conditions, you will be able to set up the system as described earlier in this section. IMPORTANT! (DISH Network only) You will need to reconfigure all of the receivers after you select a different operating mode. Refer to page 27 for details. Figure 16 Factory Reset Press MENUS until DIAGNOSTICS= No is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE SYSTEM RESET= YES? RESET TO FACTORY? ACCEPT EXIT SYSTEM RESET TRACKING DTV 101 SYSTEM NEEDS SETUP 33

Chapter 5 - Troubleshooting 5. Troubleshooting Contents This chapter identifies potential problems along with their possible causes and solutions. It also explains how to get technical support. Five Simple Checks... 37 System Status Lights... 38 Error Messages... 40 Running the Diagnostics Test... 41 Viewing System Information... 43 Calibrating the Gyros... 45 Changing Tracking Parameters... 46 Technical Support... 48 35

Chapter 5 - Troubleshooting Five Simple Checks If you are experiencing a problem receiving satellite TV with your TracVision system, perform the five simple checks below. If none of these are the problem, check the status lights on the interface box and/ or perform a diagnostics test, as explained in System Status Lights on page 38 and Running the Diagnostics Test on page 41. TIP: You can also try resetting the satellite TV receiver. Turn off and unplug the receiver, wait one minute, then plug it back in and turn it back on. Can the antenna see the satellite? The antenna requires an unobstructed view of the sky to receive satellite TV signals. Common causes of blockage include trees, buildings, bridges, mountains, and onboard equipment. Is there excessive dirt or moisture on the antenna dome? Is it raining heavily? Dirt buildup or moisture on the dome can reduce satellite reception. Clean the exterior of the dome periodically. Heavy rain or snow can weaken satellite TV signals. Reception should improve once the inclement weather subsides. Is the receiver configured for your selected mode? (DISH Network Only) All DISH Network receivers that you connect to the TracVision system need to be configured for the antenna s operating mode. To configure a receiver, you need to run its Check Switch test. Refer to the step-bystep instructions on page 27. Is everything turned on and connected properly? Make sure the power switch on the front of the interface box is turned on (the VOLTAGE light on the front of the interface box should be lit green). Also, make sure your TV and receiver are both turned on and set up for the satellite input. Finally, check the cables connecting all of these components to ensure none have come loose. 37

Chapter 5 - Troubleshooting System Status Lights Three status lights on the front of the interface box indicate the current status of the system and can help you identify problems (see Figure 17). Figure 17 System Status Lights Status Lights VOLTAGE Light During normal operation, all three status lights should be lit green. The following tables explain what the different light conditions indicate. The table below explains what the VOLTAGE light indicates. Light is... Indicates Description Off Green Green, flashing Orange Red, flashing Off OK Cable Open Low Power Bad Power Interface box is off (power switch is off) or no power input Good power (10-16 VDC at interface box) Open detected in antenna cable (check the antenna coax connection) Low power (9-10 VDC) at interface box) Insufficient power (less than 9 VDC or more than 16 VDC input) 38

Chapter 5 - Troubleshooting RECEIVER Light The table below explains what the RECEIVER light indicates. Light is... Indicates Description Green OK Good communications with receiver Orange Orange, flashing No comm Overload No communications with receiver; receiver is off or disconnected Overload or short circuit detected on the antenna cable Red Fault Power fault detected in interface box ANTENNA Light The table below explains what the ANTENNA light indicates. Light is... Indicates Description Off Green Green, flashing Orange, flashing Off Tracking Searching Overload Antenna is off, disconnected, or has insufficient power Antenna is tracking the selected satellite Antenna is searching for a satellite Overload or short circuit detected on the antenna cable Red No comm No communications with antenna Red, flashing Fault Error detected in antenna 39

Chapter 5 - Troubleshooting Error Messages The table below lists possible error messages and the appropriate corrective action. Warning SYSTEM SAT MISMATCH PRESS TO FIX SAT NOT INSTALLED TRACKING DTV 101 SYSTEM NEEDS SETUP Description The interface box and antenna are out of sync. Just press ACCEPT to synchronize. The receiver is tuned to a channel carried by a satellite that is not installed in the antenna. You might need to change your setup. This is not a true error message. This screen indicates that the system needs to be configured for the desired satellite service/ configuration. Refer to Setup on page 23 for detailed setup information. 40

Chapter 5 - Troubleshooting Running the Diagnostics Test In addition to the front panel status lights, the interface box includes a self-test function within its Diagnostics menu. Follow the steps in Figure 18 to perform a diagnostic test. For information on diagnostic test results, see Diagnostic Test Results on page 42. Figure 18 Diagnostics Test Press MENUS until DIAGNOSTICS= No is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE RUN TEST= NO NEXT MENU CHANGE RUN TEST= YES? RUNNING TEST Once the test is complete, the display shows the antenna status. ANTENNA: TRACKING PRESS TO CONTINUE Press MENUS to scroll through the remaining status messages. 41

Chapter 5 - Troubleshooting Diagnostic Test Results The table below lists all of the status messages. Status Message ANTENNA: TRACKING PRESS TO CONTINUE SATELLITE: 119 PRESS TO CONTINUE BIT ERROR: OK,928 PRESS TO CONTINUE AGC LEVEL: OK,22500 PRESS TO CONTINUE SAT 1: 119 PRESS TO CONTINUE LAT/LONG: 41N, 071W PRESS TO CONTINUE CABLE STATE: OK PRESS TO CONTINUE SYSTEM DC: OK,12.3 PRESS TO CONTINUE ANTENNA DC: OK,41.0 PRESS TO CONTINUE Description Antenna status: Idle, Initializing, Searching, Tracking, or Error Name of the currently selected satellite Bit error rate: OK: Less than 2001 High: Between 2001-8000 Bad: Greater than 8000 Automatic gain control level: OK: Between 20000-25000 Bad: Less than 20000 or greater than 25000 List of installed satellites. Press MENUS to scroll through the list Last latitude/longitude that you entered into the antenna Antenna cable status: OK, Open, or Shorted Input voltage (DC power): OK: 10-16 VDC Low: 9-10 VDC Bad: Less than 9 VDC or more than 16 VDC Antenna voltage (DC power): OK: 39-42 VDC Low: 37-39 VDC Bad: Less than 37 VDC 42

Chapter 5 - Troubleshooting Viewing System Information You can view the TracVision system s software versions and serial numbers on the interface box display. Follow the steps in Figure 19 to display the system information. For more information on system information results, see System Information Results on page 44. Figure 19 System Information Press MENUS until DIAGNOSTICS= No is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE Press MENUS until SHOW SYS INFO=NO is displayed. SHOW SYS INFO= NO NEXT MENU CHANGE SHOW SYS INFO= YES? KVH INDUSTRIES PRESS TO CONTINUE Press MENUS to scroll through the system information screens. 43

Chapter 5 - Troubleshooting System Information Results The table below lists all of the status information messages. Information Message TRACVISION M1 PRESS TO CONTINUE SYS SW: 1.2 PRESS TO CONTINUE RF SW: 1.3 PRESS TO CONTINUE MOTOR SW: 1.4 PRESS TO CONTINUE JBOX SW: 1.5 PRESS TO CONTINUE ANT.SER.# 081201234 PRESS TO CONTINUE JBOX SER.# 081205678 PRESS TO CONTINUE Description Model of TracVision Antenna Version of antenna main software Version of antenna RF software Version of antenna motor controller software Version of interface box software Serial number of antenna Serial number of interface box NOTE: The first 4 digits of the serial number indicate the year and month (YYMM) the product was manufactured. For example, if the antenna has a serial number of 081201234, it was built in December 2008. 44

Chapter 5 - Troubleshooting Calibrating the Gyros The TracVision antenna s gyros continuously measure the motion of your vessel and send this data to the antenna s motor control circuitry to keep the antenna pointed at the satellite. At the factory, each antenna gyro is precisely calibrated to work with the antenna s circuit board. Therefore, if you ever replace a gyro or circuit board in your antenna, follow the steps in Figure 20 to recalibrate the gyros for the new part. IMPORTANT! Calibrate the gyros only if directed by KVH Technical Support, and only while the vessel is stationary in calm water. A poor gyro calibration can reduce the performance of the antenna. Figure 20 Gyro Calibration Press MENUS until DIAGNOSTICS= NO is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SYSTEM RESET= NO NEXT MENU CHANGE Press NEXT MENU until CAL GYRO= NO is displayed. CAL GYRO= NO NEXT MENU CHANGE CAL GYRO= YES? CALIBRATING GYRO AZ: EL: CALIBRATING GYRO AZ: PASS EL: PASS Verify that azimuth (AZ) and elevation (EL) gyros both pass. 45

Chapter 5 - Troubleshooting Changing Tracking Parameters On rare occasions, a satellite service provider may change the configuration of one of its satellites. Since your TracVision antenna identifies a satellite based on the configuration data it has stored in memory, the antenna will no longer be able to track the satellite if its configuration changes. For this reason, the interface box allows you to change any satellite parameter stored in the antenna s memory. IMPORTANT! Change tracking parameters only if directed by KVH Technical Support. An incorrect tracking parameter can significantly reduce the performance of the antenna. Follow the steps in Figure 21 on the next page to change a tracking parameter for an installed satellite. 46

Chapter 5 - Troubleshooting Figure 21 Tracking Parameter Changes Press MENUS until DIAGNOSTICS= NO is displayed. DIAGNOSTICS= NO NEXT MENU CHANGE DIAGNOSTICS= YES? ENTERING DIAGNOSTICS SATELLITE= 119? Select the satellite you need to modify. POLARIZATION= RIGHT? Select the polarization you need to modify. SYSTEM RESET= NO NEXT MENU CHANGE BAND= USA? CHANGE ACCEPT Press NEXT MENU until TRACKING PARAMS= NO is displayed. TRACKING PARAMS= NO NEXT MENU CHANGE TRACKING PARAMS=YES? FREQUENCY= 12345? NEXT PARAM CHANGE Select 10700-12700MHz. SYMBOL RATE= 12345? NEXT PARAM CHANGE Select 10000-45000 kilosymbols per second. FEC CODE= 5/6? NEXT PARAM CHANGE Select 1/2, 2/3, 3/4, 5/6, 6/7, 7/8, or Auto. NETWORK ID= 0x1234? NEXT PARAM CHANGE Select 0x0000-0xffff (hexadecimal). DONE? NEXT PARAM ACCEPT 47

Chapter 5 - Troubleshooting Technical Support Product Registration Your TracVision system is a sophisticated electronic device; only KVH-authorized technicians have the tools and expertise necessary to diagnose and repair a system fault. Therefore, if you experience an operating problem or require technical assistance, please call or visit your local authorized TracVision dealer or distributor. You can find an authorized technician near you by visiting our website at www.kvh.com/wheretogetservice. If you need help finding an authorized technician, please contact KVH Technical Support: Phone: +1 401 847-3327 E-mail: techs@kvh.com (Mon.-Fri., 9 am-6 pm ET; Sat. 9 am-2 pm ET) Be sure to register your TracVision system with KVH. The registration process is quick, easy, online, and ensures the best possible service from KVH. Visit www.kvh.com/register or refer to the Product Registration Form. When you register, you ll enjoy a wide range of benefits, including: Free e-mail notification of enhancements and software updates to improve the performance of your system Fast, convenient customer and technical support Alerts about changes and improvements to services and programming Product news and special offers Complete privacy - KVH will never sell or share your data with other companies or organizations 48

Appendix A - Wiring Diagrams Appendix A Wiring Diagrams Contents This appendix provides wiring diagrams for various receiver configurations. Wiring Diagram - 1 Receiver... 51 Wiring Diagram - 2 Receivers... 52 Wiring Diagram - 3 Receivers... 53 49

Appendix A - Wiring Diagrams Wiring Diagram - 1 Receiver To Antenna Interface Box To KVH Antenna Unstacked Output Satellite TV Receiver (Primary) Satellite In 51

Appendix A - Wiring Diagrams Wiring Diagram - 2 Receivers To Antenna Interface Box Stacked Output Unstacked Output To KVH Antenna Satellite TV Receiver (Primary) Satellite In NOT USED This receiver controls satellite selection Input INPUT To To TV Destacker Output OUTPUT / To RECEIVER Satellite TV Receiver Satellite In Destacker (Single-Output) Required The single-output destacker (KVH part #19-0347) converts a stacked signal into an unstacked signal, which standard satellite TV receivers are configured to decode. The interface box has two satellite TV outputs: Unstacked and Stacked. You will need to install the destacker between the Stacked output and your second receiver. Primary Receiver Controls Satellite Selection 52 The receiver that you connect to the Unstacked output is the primary receiver. If the system is set up for automatic switching, the primary receiver controls satellite selection.

Appendix A - Wiring Diagrams Wiring Diagram - 3 Receivers To Antenna Interface Box Stacked Output Unstacked Output To KVH Antenna Destacker Input INPUT Satellite TV Receiver (Primary) Satellite In To RECEIVER This receiver controls satellite selection 2 1 To TV Satellite In Satellite TV Receivers Satellite In Destacker (Dual-Output) Required The dual-output destacker (KVH part #19-0410) converts a stacked signal into two unstacked signals, which standard satellite TV receivers are configured to decode. The interface box has two satellite TV outputs: Unstacked and Stacked. You will need to install the destacker between the Stacked output and your second and third receivers. Primary Receiver Controls Satellite Selection The receiver that you connect to the Unstacked output is the primary receiver. If the system is set up for automatic switching, the primary receiver controls satellite selection. 53

Appendix B - Menus Quick Reference Guide Appendix B Menus Quick Reference Guide Contents This appendix provides a quick reference guide to the interface box menu structure. Interface Box Menus... 57 55

Appendix B - Menus Quick Reference Guide Interface Box Menus Press EXIT at any time to exit the menu BRIGHTNESS= HIGH NEXT MENU CHANGE HIGH - MEDIUM - LOW LAT/LONG= 41N, 071W NEXT MENU CHANGE Enter your position DIAGNOSTICS= NO NEXT MENU CHANGE SYSTEM RESET= NO NEXT MENU CHANGE RUN TEST= NO NEXT MENU CHANGE Reset system to factory conditions to change system setup Run system self-test SHOW SYS INFO= NO NEXT MENU CHANGE View system information SAT SWITCH= AUTO NEXT MENU CHANGE AUTO - MANUAL CAL GYRO= NO NEXT MENU CHANGE Calibrate antenna gyros TRACKING PARAMS= NO NEXT MENU CHANGE Change satellite tracking parameters 57

www.kvh.com KVH Industries, Inc. Middletown, RI U.S.A. Tel: +1 401 847 3327 Fax: +1 401 849 0045 E-mail: info@kvh.com KVH Europe A/S Kokkedal, Denmark Tel: +45 45 160 180 Fax: +45 45 160 181 E-mail: info@kvh.dk KVH Norway AS Horten, Norway Tel: +47 33 03 05 30 Fax: +47 33 03 05 31 E-mail: commboxsales@kvh.com KVH Singapore Singapore Tel: +65 6829 2343 Fax: +65 6829 2121 E-mail: infokvhsingapore@kvh.com