ø22mm - W Series Oiltight W Series Switches and Pilot Devices: 22mm W Series offer flexibility in space-saving package Key features include: P board mount, solder or screw terminal ollective mounting saves space Non-reflective lens Highly visible marking plate Tamper proof construction ight touch reduces strain Gold or silver contacts emovable contacts simplify wiring and facilitate PB applications W Series switches and pilot lights can be mounted collectively on 1.0" centers. ombined with pcb terminals and locking lever removable contacts, this eases manufacture of pre-fab pushbutton arrays (as pictured). P Board tracing/soldering of contacts can be done in tandem with panel cutting/operator installation. All W series units mount by means of a locking ring that comes on from the rear of the panel, as such they can not be removed from outside the panel and are relatively tamperproof. ombining the snap action and tactile feel of miniature commercial pushbuttons with the size and ruggedness of industrial pushbuttons, W pushbuttons are a unique solution to many applications. hoose from standard silver contacts or low-level gold plated contacts. s available in.110" solder tab, M3 screw, or pcb pins. U ecognized File # E55996 SA ertified File No. 21451 egistration No. J9551801-108
Oiltight ø22mm - W Series Specifications Specifications Operating Temperature Storage Temperature Operating Humidity ontact esistance Insulation esistance Switch Unit Dielectric Strength Illumination Unit Vibration esistance Shock esistance Mechanical ife Electrical ife Degree of Protection Insulation Voltage 25 to +60 (without freezing) ED illuminated type: 25 to +50 40 to +80 45 to 85% H 50mΩ maximum (initial value) 100MΩ minimum (500V D megger) Between live part and ground: 2,500V A, 1 minute Between terminals of different poles: 2,500V A, 1 minute Between terminals of the same pole: 1,000V A, 1 minute Between live part and ground: 2,500V A, 1 minute Operating extremes: 5 to 55Hz, Amplitude 1.0mm p-p Damage limits: 1,000 m/sec 2 (Approx. 100G) Operating extremes: 100 m/sec 2 (Approx. 10G) Momentary: 1,000,000 operations minimum Maintained: 500,000 operations minimum Selectors: 250,000 operations minimum Momentary: 100,000 operations minimum (at 1,800 operations/hour) Maintained/Selector: 100,000 operations minimum (at 900 operations/hour) Watertight/oiltight IP65 (IE Pub529) (except key selectors) 250VA/D Materials Style enses Operators Marking Plates polyarylate polyacetate acrylic resin.110" Solder tab/quick connect P board terminal (gold contacts only) Screw terminal (DPDT units only) ontact atings ontact Material Thermal urrent ontact ating emarks 30VD/0.1A resistive Gold-clad cross-bar 3A Minimum applicable load (reference value): 5V, 1mA A/D. 125VA/0.1A resistive (Applicable range is subject to the operating condition and load.) ontact 5A 30VD/2A resistive 30VD/1A inductive 125VA/3A resistive(50/60hz) 125VA/2A inductive (50/60Hz) 125VD/0.4A resistive 125VD/0.2A inductive 250VA/2A resistive(50/60hz) 250VA/1.5A inductive (50/60Hz) A inductive load: PF=0.6 to 0.7, D inductive load: /=7ms maximum. amp atings ED Voltage 6V A/D ±10% 12V A/D ±10% 24V A/D ±10% 120V A ±10% 240V A ±10% urrent/wattage 17mA max 11mA max 11mA max 10mA max 10mA max U ecognized File # E55996 SA ertified File No. 21451 Incandescent 6.3V A/D ±5% 1W 12V A/D ±10% 1W 24V A/D ±10% 1W egistration No. J9551801 ED lamps contains a built-in current-limiting resistor and reverse polarity protection diode. -109
Oiltight ø22mm - W Series ED and Incandescent Pilot ights (Sub-Assembled) emovable * + Operator + amp + ens = ompleted Unit * emovable terminals are applicable for PB terminated types only. Part Numbers: Pilot ight Operators Termination Style Solder P Board Screw ound W1P-00 W1P-0 W1P-00M Square W2P-00 W2P-0 W2P-00M 1. equires W-00V removable terminals in addition to operator. 2. Solder and screw terminals are unibody design (they do not use a removable terminal block). Part Numbers: enses Type ound W1A-P1-➁ Part Number Square W2A-P1-➁ In place of ➁, specify ens olor ode. Part Numbers: amps (not included in assemblies) Type Voltage Part Number ED 6V A/D±10% STD-6➁ 12V A/D±10% STD-1➁ 24V A/D±10% STD-2➁ 120V A±10% STD-H2➁ 240V A ±10% STD-M4➁ Incandescent 6.3V A/D IS-6 12V A/D IS-12 ➁ ED/ens olor ode olor ode Amber A Green G ed Blue S White W Yellow Y 24V A/D IS-24 1. In place of ➁, specify the ED olor ode. 2. The ED contains a current-limiting resistor and reverse polarity protection diode. -115
ø22mm - W Series Oiltight Part Numbers: W1S Selector Switches Style Position ontact Material ontact Part Number Solder/Tab P Board Screw ound SPDT W1S-21 W1S-21V 90 2-position maintained Gold DPDT W1S-22 W1S-22V W1S-22M 3PDT W1S-23 W1S-23V SPDT W1S-25 DPDT W1S-26 W1S-26M 3PDT W1S-27 45 3-position DPDT W1S-32 W1S-32V W1S-32M maintained Gold 3PDT W1S-33 W1S-33V DPDT W1S-36 W1S-36M 3PDT W1S-37 1. Knob color: Black; Directional Indication olor: White 2. For contact operation, see next page. 3. For sub-assembly part numbers, see page -118. Part Numbers: W1K Keylock Selector Switches Style Position ontact Material ontact Part Number Solder/Tab P Board Screw ound SPDT W1K-21A W1K-21VA 90 2-position Gold DPDT W1K-22A W1K-22VA W1K-22MA maintained 3PDT W1K-23A W1K-23VA SPDT W1K-25A DPDT W1K-26A W1K-26MA 3PDT W1K-27A 45 3-position DPDT W1K-32A W1K-32VA W1K-32MA maintained Gold 3PDT W1K-33A W1K-33VA DPDT W1K-36A W1K-36MA 3PDT W1K-37A Part Numbers: W1F ED and Incandescent Illuminated Selector Switches Style Position ontact Material ontact Part Numbers Solder/Tab P Board Screw ound SPDT W1F-210-➁ W1F-210V-➁ 90 2-position Gold DPDT W1F-220-➁ W1F-220V-➁ W1F-220M-➁ maintained 3PDT W1F-230-➁ W1F-230V-➁ SPDT W1F-250-➁ DPDT W1F-260-➁ W1F-260M-➁ 45 3-position maintained Selector and Keylock Switches (Assembled) 1. Every key selector uses an identical key. 2. The key is removable in all positions. 3. If a different configuration is required, contact an IDE representative for more information. 4. For contact operation, see next page. 5. For sub-assembly part numbers, see page -118. Gold 1. In place of ➁, specify color code. See previous page for color codes. 2. amps must be ordered separately for all illuminated pushbuttons. See previous page. 3. For contact operation, see next page. 4. For sub-assembly part numbers, see page -118. 3PDT W1F-270-➁ DPDT W1F-320-➁ W1F-320V-➁ W1F-320M-➁ 3PDT W1F-330-➁ W1F-330V-➁ DPDT W1F-360-➁ W1F-360M-➁ 3PDT W1F-370-➁ -116
Oiltight ø22mm - W Series ontact Operations ontact Operation: Selector and Keylock Switches Position 90 2-Position Maintained ontact SPDT DPDT 3PDT eft N Operator Position and ontact Position (Top View) eft enter ight N ight N eft enter ight N N N _ eft N N ight N eft enter ight N N N eft ight eft ight eft ight DPDT N N N N N N 45 3-Position Maintained 3PDT eft enter ight eft enter ight eft enter ight N N N N N N N N N Arrangements (Bottom View): W and W B Pushbuttons 3 pole illuminated 2 pole illuminated 3 pole non-illuminated amp (+) X1 N N N amp (+) X1 N N N N N amp ( ) amp ( ) SPDT has, and N only on the center. DPDT has,, and N only on the right and left. SPDT has, and N only on the right. DPDT has,, and N only on the right and center. -117
Oiltight ø22mm - W Series Dimensions: Selector and Keylock Switches, continued and ayouts W1F ED and Incandescent Illuminated Selector Switches M3 Screw over W-V2M 8.2 54.9 6.8 6.8 5 5 4.85 6.5 1.2 53.5 5.4 36 over W-V2 6.8 6.8 6 6 6.5 4.85 P Board (solder) 0.8 0.5t 1.2 2.6 Gasket ocking ing TOP OK Anti-otation ing 47 Tab (solder) Width 2.8 0.5t 8.5 11.7 9 36 0.5 9 Panel Thickness: 0.8 to 6 mm 17.5 23.2 ound 18 25.4 ø25.8 OK 16.2 ound w/square Bezel Screw P Board Solder/Tab Screw P Board Solder/Tab X1 N 25.8 18 25 N OK 18.2 16.2 18 25 26.2 OK 1.0 2.6 1.2 2-0.6 ayouts W P Board Drilling ayout P Board Bottom View 0.265" (6.8mm) 0.189" (4.85mm) 0.265" (6.8mm) 0.254" (6.5mm) W B P Board Drilling ayout P Board Bottom View 0.265" (6.8mm) 0.189" (4.85mm) 0.265" (6.8mm) Pilot ights P Board Drilling ayout P Board Bottom View 0.047" (1.2mm) 0.443" (11.35mm) ø0.047" (ø1.2mm) holes Mounting Hole ayout ø0.87" +0.02" - 0 (ø22.3 +0.16" mm) 0 1.014" (26mm) Note 2 0.047" (1.2mm) ø0.047" (ø1.2mm) holes 0.047" (1.2mm) 1. When determining mounting centerlines, allow for easy operation. 2. Mushroom (Ø 1.17" (Ø 30mm)) = 1.248" (32mm) Tab terminal = 1.014" (26mm) (with/without terminal cover) P board terminal = 1.014" (26mm) Screw terminal = 1.56" (40mm) 3. Mushroom (Ø 1.17" (Ø 30mm) = 1.248" (32mm) Tab terminal = 1.053" (27mm) (with terminal cover) Tab terminal = 1.014" (26mm) (without terminal cover) P board terminal = 1.014" (26mm) Screw terminal = 1.014" (26mm) ø0.047" (ø1.2mm) holes 1.014" (26mm) Note 3-123